Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) ~ SUNRISE TELECOM incorporated SunSet STS- 1 User's Manual 58351 Version 2.00 Sunrise Telecom...Q step ahead
1.0 SPECIFICATIONS CONNECTORS 8T8-1 Receive!Transmit - BNC DS3 Receiveffransmit - BNC DS1 Receiverrransmit/External Clock - Bantam Serial Port - 8 pin Mini DIN RS232C (V.24), DTE DC Power STATUS AND ALARM INDICATORS 8TS-1: Pulses, Frame Sync, Alarm, Errors, BPV, Pointer D83: Pulses, Frame Sync, Alarm, Errors OS1NT1.5: Pulses, Frame Sync. B8ZS, Errors, Alarm, VT Pointer Test pattern: Pat Sync, Bit Error General: Power, Low Battery Charging 20 Tri-state Indicators: Red, Green, Off (Example: Frame Sync Green = frame sync established, Frame Sync Red = loss of frame) STS-1 GENERAL Framing: Conforms to ANSI T1.105, GR-253-CORE Line Coding: B3ZS Clock Source: Internal (51.840 MHz, ±5 ppm), Loop (recovered) OS3 drop/insert, DS1NT1.5 drop/insert Payload Formats: 083, D83/D81, VT1.5 STS-1 Transmitter Nominal Levels: High, DSX, Low DSX conforms to ANSI T1.102, Bellcore GR-253-CORE STS-1 Receiver Input Impedance: 750 Input Sensitivity: +3 db to -26 db resistive loss, or 450 f1. cable loss from STSX 1 DS3 GENERAL Signal Directions: multiplexed through 8TS-1 connectors, or directly to DS3 connectors. D83 connectors require 8W351. Framing: Unframed, M13, C-bit parity. Conforms to ANSI T1.1 02. 107, 107A, 403, and 404. Also Bellcore TR-TSY-000009 and TR-TSY-000191 Line Coding: B3ZS Ch.7 Specs & Configs 7-1
Clock Source: Internal (44.736 rvlhz, ±5 ppm), Loop (recovered) Test Patterns: 1111, 1100, 1010, 0000; Programmable up to 24 bits, 10 user patterns up to 24 bits with names, 2 15 _1, 2 2-1, 2 23 1; 1-in-8, 1-in-16; 3-in-24 FEAC data link in C-bit parity framing control and analysis (requires option SW361) Loopbacks: FEAC loopbacks per AI\JSI T1.401, 1\1113 C-Bit loopback per TR-TSY-000009 (requires option SW361) Payload Fonnats: DS3 or DS3IDS] DS3 Transmitter Transmit Signal Source: DS3 Test pattern, DS1 Test pattern broadcast, DS 1 AIS broadcast, ~oop received DS3 signal Nominal Voltages: High, DSX, Low Pulse Shape conforms to CCITIG. 703. Bel/core TR-TSY-000499. DS1 Insert: Insert DS1 on desired channel. Other channels have DS1 test pattern copies, AJS, or are looped through from DS3 receiver. DS1 generated internally or from DS1 Rx connector. Generate Yellow Alarm (X-bits alarm), AIS and IDLE DS3 Receiver Input Impedance: 7SQ. Input Sensitivity: DSX: up to 26 db resistive or 6 db cable loss from DSX High/low: +6 db to -26 db resistive loss Jitter tolerance: Conforms to TR-TSY-000009 DS1 Drop: drop to internal receiver or drop to DS1 TX connector DS1 General Signal Directions: multiplexed through ST8-1 or DS3 connectors, or directlythrough DS1 connectors. DS1 and DS3 connectors require SW351. Clock Source: Internal (1.544 Mbps ±5 ppm), loop (recovered, ±300 ppm), External (1.544 Mbps ±300 ppm, 0 to -30 db resistive) Framing: Unframed, superframe (SF/D4), ESF, SLC-96~. Conforms to ANSI T1.1 02, 107, 107A, 403. and 404. Also Bellcore -rr-tsy-000009 and -rr-tsy-000191. *SLC is a reg. trademark of AT&T. Line Coding: AMI, 88ZS Test Patterns: Standard Patterns: 1111, 1100, 1010, 0000; 1-in 8 (1 :7), 1-in-16, 3-in-24; QRS. 2 6-1, 2 7-1 t 2 9-1 t 2 11 _1, 2 15 _1, 2 2 _ 7-2 SunSet STS-l;JVersion 2.00
1, 2 23 _1 User Programmed Patterns: 10 ea patterns up to 32 bits long, alphanumeric name up to 10 characters for each pattern Test Pattern Inversion Fractional T1: Any arbitrary combination of 1 to 24 channels. Nx56 or Nx64 format. Autoconfigure (requires option SW370). ANSI T1.403 data link send and receive. Bit oriented messages, performance report message (requires option SW371). TR-TSY-000008 SLC-96 data link monitor. Mode I and III (requires option SW371). Loopbacks: CSU/NIU loop up/down, inband, ESF datalink, programmable up to 32 bit control Other intelligent NIUs: Support for Westell and Teltrend looping line repeaters, central office repeaters, performance monitoring NIUs, maintenance switches (requires option SW372) CSU/NIU Emulation: Responds to in-band and ESF datalink loopbacks by looping up. Line and Payload style loopbacks. Manual loopback control. Simultaneous line measurements (requires option SW373). DS1 Transmitter Pulse Shape: Conforms to CCInG. 703, Bellcore TR-TSY-000499 Output Levels: 0, -7.5, -15, -20 db DS1 Receiver Input Frequency: 1.544 Mbps, ±300 ppm Input Impedance: Term, DSXMON, and Loop 100.0. Bridge >10000. Input Sensitivity: Term, Bridge +6 db to -36 db cable loss. DSXMON -15 db to -26 db resistive loss. Measurements G.821 and general errors: Bit error, bit error rate, errored seconds, 0;0 errored seconds, severely errored seconds, 0;0 severely errored seconds, error-free seconds, % error-free seconds, available seconds, unavailable seconds, sync loss seconds, degraded minutes ST8-1: Signal loss second, frame loss second, loss of clock second, out of frame, loss of pointer second, path AIS second, line AIS second, path yellow second, REI second, section CV 81, line CV 82, path CV 83, BPV, Positive/Negative pointer adjustments, APS counts, Path REI, frequency, new pointer Ch.7 Specs & Configs 7-3
D83: Frame loss seconds, loss of signal seconds, BPV, BPV rate, F-bit error, F-bit error rate, P-bit error, C-bit error, FEBE, AIS seconds, yellow alarm seconds, frequency D82: F-bit error, frame loss seconds, AIS seconds, signal loss seconds OS 1: BPV, BPV rate, F-bit error, bit error, CRC-6 block error, CRC 6 block error rate, BPV, out of frame count, change of frame alignment count, frequency, level, AIS seconds, loss of frame seconds, loss of signal seconds, yellow alarm seconds, low density seconds, excess zeroes seconds, frequency VT1.5: VT LOP seconds, FEBE, VT yellow alarm seconds, VT AIS seconds, BIP-2 error, VT pointer Positive/Negative adjustment, New Oata Flag General 8W options upgradable via SunWare cartridge replacement Error Injection: DS1: BPV, Logic, FBE (083/081, VT1.5, 81/0S1); 083: BPV, Logic, BFE, FEBE, C-Bit, P-Bit (81/0S3). Rate for BPV and Logic only. Alarm Generation: AIS, Yellow, OS3 idle Remote Control: menu-driven, VT102 terminal emulation Printer: Print every 5 (or 3) to 99 minutes, print at end of measurement, print on error/alarm events, print screen alphanumerics Storable System Configurations Operating temperature: 0 to 50 C (32 to 122 0 F) Storage temperature: -20 to 70 C (-4 to 158 0 F) Size: 10.5 x 7 x 27 em (4 x 2.8 x 10.5 11 ) Weight 1.36 kg (3 Ib) Humidity: 5% to 90% noncondensing 2.0 Configurations Here are the various items which may be ordered in addition to the basic STS-1 88350. The following packages provide everything you need in one convenient order number. If you prefer, you may order most items individually. Model SS350 7-4 Name and Description SunSet STS-1 Chassis Body of test set. Comes with 120 VAC Battery Charger, SunWare Cartridge and SunSet ST8-1 Use(s Manual. SunSetSTS-IPVersion 2.00