AI Nano CNC for High-Speed, High-Accuracy machining

AI Nano CNC for High-Speed, High-Accuracy machining FANUC Series 30*/31*/32*-MODEL A FANUC Series 300*/310*/320*-MODEL A FANUC Series 300*s/310*s/320*s-MODEL A F30i-A(SpecE)-08 2008.10

:Standard :Standard option :Option :Function included in another option -:Not Available 5 Controlled axis Max. controlled axes (Machine controlled axes + Loader controlled axes) (Machine controlled axes are including Cs axes) Machine groups Control paths 32 axes J802 - - - - - - 20 axes - - - - 9 axes - - - - - - 1group Max. 3 groups S836 - - Max. 2 groups - - - - - - 1 path Max. 10 path S801 - - - - - - Max. 4 path - - - - Max. 2 path - - - - - - Control axes(each path) 2 axes - - - - Simultaneously controlled axes (each path) Controllable axes expansion ( each path ) (including PMC axes and Cs axes) Simultaneously controlled axes expansion( each path) 3 axes - - - - Simultaneous 2 axes Max. 24 axes J801 - - - - - - Max. 12 axes - - - - Max. 5 axes - - - - - - Max. 24 axes J803 - - - - - - Max. 5 axes - - - - - - Max. 4 axes - - - - Axis control by PMC Max. 32axes. (Not available on Cs axis) J804 - - - - - - Designation of Spindle axes ( each path / Total ) Cs contouring control ( each path / Total ) Max. 16axes. (Not available on Cs axis) - - - - Max. 8axes. (Not available on Cs axis) - - - - - - Max. 4 axes / 8 axes S837 - - - - - - Max. 4 axes / 6 axes - - - - Max. 2 axes / 2 axes - - - - - - Max. 4 axes / 8 axes J852 - - - - - - Max. 4 axes / 6 axes - - - - Max. 2 axes / 2 axes - - - - - - Controlled path for Loader Max. 8 path - - - - - - Controlled axes for Loader Simultaneously controlled axes for Loader Axis control by PMC for Loader Max. 2 path - - - - Max. 1 path - - - - - - Max. 4 axes Max. 4 axes Max. 4 axes Basic three axes are X, Y and Z, Axis name additional axes are optional from U, - - - - V, W, A, B and C. Axis name expansion Arbitrary axis name setting Spindle name expansion Synchronous/Composite control Superimposed Control Superimposed control for high-speed cycle machining Synchronous/Composite/Superimposed control by program command In case of G code system A, basic 2 axes are X and Z, additional axes are optional from Y, A, B and C. In case of G code system B/C, basic 2 axes are X and Z, additional axes are optional from Y, U, V, W, A, B and C. Max 3 characters Included in Custom macro function Max. 3 characters. Included in Multispindle function. Superimposed control and, Highspeed cycle machining or High speed binary program operation is S816 S818 - - - - - - - - R554 - - S890 Flexible path axis assignment R607 (8)

5 Axis synchronous control Max. 12 pairs. J843 - - - - - - Max. 6 pairs. - - - - 2 pairs. - - - - - - Twin table control J698 - - - - Parallel Axis Control Only for 1 path control R509 - - - - - Arbitrary angular axis control J924 Inclined Rotary Axis Control S688 - - - - Pivot axis control S665 - - Tandem control J733 Tandem Disturbance Elimination Control Axis synchronous control is S660 Torque control Included in PMC axis control. - - Pole Position Detection Function Control axis detach S744 J807 Chopping J707 - - - - Chopping function by flexible synchronous control Increment system Increment system C IS-A, IS-B J805 Increment system D 0.00001mm 0.00001deg 0.000001inch S694 - - - - - Increment system E 0.000001mm 0.000001deg 0.0000001inch S805 - - Flexible feed gear Optional DMR Arbitrary command multiply 1/9999-9999times S806 Learning control J705 - - Preview repetitive control J706 - - Learning control for parts cutting Learning Control for Rigid Tap Dual position feedback HRV2 control HRV3 control R510 R539 J704 J398 HRV4 control J399 - - Inch/metric conversion Interlock Machine lock Emergency stop Over travel Stored stroke check 1 all / each axis J876 Stored stroke check 1 area expansion R552 - - Stroke limit external setting Stored stroke check 2,3 Stored limit check before move Stroke limit area changing function Chuck and tail stock barrier J720 - - - - Mirror image Follow-up Servo off/mechanical handle each axis Chamfering on/off - - - - Interference check for each path Only for more than 2 path control J839 - - - - J845 J840 J749 R585 Interference check for rotary area S643 - - Built-in 3D interference check R541 - - 3D interference check with Open CNC *12 R542 - - Unexpected disturbance torque detection function J718 FANUC AC SERVO MOTOR i Series Unexpected disturbance torque detection S812 Fine torque sensing J982 - - Rotary axis control J743 - - Position switch J846 High speed position switch J987 - - Direction-dependent type of high speed position switch Linear scale I/F with absolute address reference mark Linear scale I/F expansion with absolute address reference mark Temporary absolute coordinate setting 0.0001mm 0.0001deg 0.00001inch All / each axis, each direction, block start, cutting block start S721 - - J670 S730 J786

5 Dual check safety Safety spindle speed limit override S661 R626 Axis immediate stop function R613 - - Operation Automatic operation MDI operation DNC operation DNC operation with memory card Schedule function Program number search Sequence number search Sequence number comparison and stop Program restart Auxiliary function output in the program restart CF card and PCMCIA Card Attachment is Program restart is *2 J844 J838 R576 Quick program restart R630 (8) Tool retract and recover Manual intervention and return Wrong operation prevention Retraction for Rigid tapping Retraction for 3-dimensional rigid tapping Buffer register Dry run Single block Manual continuous feed (JOG) Manual reference position return Manual 2nd/3rd/4th reference position return Reference position setting without DOG Reference point setting with mechanical stopper Reference point setting with mechanical stopper by Grid Method Reference position return speed set Reference position shift J823 R623 J664 R575 R558 J729 S945 Manual handle feed 1-unit 1 unit J835 Manual handle feed 2/3-units 2 units/3 units J836 Manual handle feed 4/5-units Max. 5 units S858 Manual handle feed rate Manual handle feed multiple 10 million 1 10 m n m 0 2000 0 2000 R600 3-dimensional manual feed S679 - - Handle interruption Manual interruption of 3-dimensional coordinate system conversion FANUC AC SERVO MOTOR i Series with I/O Link Manual handle interface Incremental feed 1 10 100 1000 10000 Jog and handle simultaneous mode J837 S949 S722 Manual numerical command J667 - - Reference position signal output S629 Retrace J730 - - - - Manual handle retrace J998 Manual handle retrace for multi path R606 - - Direction change movement in auxiliary function output block function Manual handle retrace is S628 Manual liner/circular interpolation Only for 1path J774 Active block cancel High speed program check I/O Link expansion 3rd channel is Dual check safety is Reader/puncher interface is Rigid tapping and Retraction for rigid tapping are 3rd/4th reference position return function is Manual handle feed 1-unit is required Manual handle feed 1-unit, Handle interruption and 3-dimensional coordinate conversion are required S627 S880

5 Dwell/Auxiliary function time override function Pulse superimposed function Interpolation functions Nano interpolation Positioning R500 R559 Single direction positioning G60 J812 Exact stop mode Tapping mode Cutting mode Exact stop Linear interpolation Circular interpolation G61 G63 G64 G09 Exponential interpolation J711 - - Dwell in seconds and dwell in revolution (In case of dwell in Dwell (Second designation) revolution for M system, threading, synchronous cutting option is ) Polar coordinate interpolation Cylindrical interpolation Cylindrical interpolation by plane distance command Helical interpolation J815 J816 Cylindrical interpolation is R578 (8) J819 Circular interpolation plus max. 4 Helical interpolation B J655 - - - - - - axes linear interpolation. Involutes interpolation J710 - - Helical involute interpolation S853 - - Hypothetical axis interpolation J652 - - Conical/spiral interpolation J780 - - Smooth interpolation J777 - - Nano smoothing AI contour control I or is S687 - - Nano smoothing 2 AI contour control I or is R512 - - - - Thread cutting, synchronous cutting Multi threading Thread cutting retract Continuous threading Variable lead thread cutting J824 J825 J827 Circular thread cutting J731 - - Circular thread cutting B Helical interpolation is R631 - - - - - Polygon turning Polygon machining with two spindles Skip Multi-step skip G31 J817 J708 J849 High-speed skip Input signal is 8 points. J848 Torque limit skip Reference position return Reference position return check 2nd reference position return 3rd/4th reference position return Manual handle feed 1-unit, Manual handle feed 2/3-unit (or Manual handle feed 4/5-unit) and Handle interruption are required G00 (Linear interpolation type positioning is possible) Circular interpolation plus max. 2 axes linear interpolation Spindle serial output is G28 G27 J830 Floating reference position return J831 - - Normal direction control J813 - - - - NURBS interpolation J669 - - 3 dimensional circular interpolation S673 - - - - Balanced cutting Only for more than 2 path control J834 - - - - Index table indexing J822 - - - - Continuous high-speed skip J770 - - - - - Gentle normal direction control J986 - - - - - Continuous dressing for grinding machine J630 - - - - Infeed control for grinding machine J631 - - - - High-speed cycle cutting J832 - -

5 High-speed cycle machining retract function J663 - - High-speed cycle machining and High-speed cycle machining skip function S662 - - Macro executor are High-speed cycle cutting additional variables A High-speed cycle cutting additional variables B High-speed cycle cutting additional variables C High-speed cycle cutting additional variables D High-speed cycle machining operation information output function General purpose retract 131,072 variables J745 - - 262,144 variables J746 - - 768,432 variables S640 - - 2,000,000 variables R513 - - R609 - - J997 Path Table Operation S886 - - Spindle Speed fluctuation detection for Path Table Operation Polygon turning function for Path Table Operation Threading start position shift function for Path Table Operation R605 - - R598 - - R599 - - High speed binary program operation R516 - - High speed binary program operation retract function Feed function Rapid traverse rate Max. 999.999m/min 1 m Max. 99.9999m/min 0.1 m Rapid traverse override Fo, 25, 50, 100% or 0 100%(1% Step) Feed per minute Feed per revolution Without position coder feed per revolution Without position coder constant surface speed control Tangential speed constant control Cutting feedrate clamp Automatic acceleration/deceleration Rapid traverse bell-shaped acceleration/deceleration Optimum torque acceleration/deceleration Positioning by optimum acceleration Bell-shaped acceleration/deceleration after cutting feed interpolation Linear acceleration/deceleration before cutting feed interpolation Feedrate override 0-254% S658 - - S675 J693 J829 - - 2nd feedrate override 0-254% J810 - - One-digit F code feed J820 - - - - Inverse time feed J715 - - - - Jog override 0-655.34% Override cancel Manual per revolution feed - - - - External deceleration J842 Feed stop J847 - - Automatic corner deceleration Feedrate control with acceleration in circular interpolation Linear acc/dec after cutting feed interpolation High-speed cycle machining and Macro executor are High-speed cycle machining and Macro executor are Path Table Operation is Path Table Operation and Spindle control with servo motor are Path Table Operation and custom macro are High speed binary program operation is Max. 99.9999m/min 0.01 m Max. 99.9999m/min 0.001 m For M system, threading, synchronous cutting option is Included in constant surface speed control. Included in constant surface speed control. Rapid traverse: linear Cutting feed: exponential, linear Included in AI contour control I or Included in AI contour control I or J809

5 AI contour control I Look-ahead block no. is Max 30 S807 Look-ahead block no. is Max 200 AI contour control II (32i Max 80) (Path number <= 4 S808 and Axes number <=20) Look-ahead block no. is Max 600 High-speed processing AI contour control is (Path number <= 2 S809 - - and Axes number <=12) Look-ahead block no. is Max 1000 Look-ahead blocks expansion S815 - - AI contour control is required Bell-type acceleration/deceleration before look ahead interpolation Included in AI contour control I or Jerk control AI contour control is S678 Rigid tapping bell-shaped acceleration/deceleration Rigid tapping is Optimum torque Rigid tapping is acceleration/deceleration for rigid tapping R533 programmable rapid traverse overlap Program input Tape code Label skip Parity check Control in/out Optional block skip 1 EIA/ISO Horizontal and vertical parity S702 R502 Optional block skip 9 J955 Max. programmable dimension Program file name Sequence number Absolute/incremental programming Decimal point programming/pocket calculator type decimal point programming Input unit 10 time multiply Diameter/Radius programming Dynamic switching of diameter/radius specification Plane selection Rotary axis designation Rotary axis roll-over 32 characters N8 digit Combined use in the same block G17 G18 G19 S630 - - Polar coordinate command J818 - - - - Coordinate system setting Automatic coordinate system setting Workpiece coordinate system G52 - G59 J894 Workpiece coordinate system preset Addition of workpiece coordinate system 48-pairs Addition of workpiece coordinate system 300-pairs Direct input of workpiece origin offset value measured Manual absolute on and off J917 48 pairs J895 300 pairs J919 - - Direct drawing dimension programming J870 - - - - G code system A - - - - G code system B/C J871 - - - - Lathe/Machining center G code system switching function Chamfering/Corner R J875 - - - - R597 Optional chamfering corner R S615 - - - - Programmable data input Programmable parameter input Sub program call Custom macro Addition of custom macro common variables Custom macro common variables between each path 9 digit (R,I,J and K is 12digit ) Included in workpiece coordinate system. Tool offset for Milling and Turning function is G10 10 folds nested J873 #100 - #199 #500 - #999 J887 Only for more than 2 path control

5 Interruption type custom macro Canned cycle - - - - Multiple repetitive cycles J877 - - - - Multiple repetitive cycles II Pocket profile J889 - - - - Canned cycle for drilling In-position check switching function for drilling canned cycle Circular interpolation by R programming J874 J890 Canned cycle for drilling is R648 (8) R,I,J,K 12digit Mirror image for double turret J881 - - - - Automatic corner override Scaling Coordinate system rotation 3-dimensional coordinate system conversion J891 J892 J893 J713 Tilted working plane command S676 - - Tilted working plane command with Guidance Programmable mirror image R522 - - J880 Figure copying J897 - - - - - Tape format for FS15 J882 - - Tape format for FS10/11 J882 - - - - - - Macro executor Macro executor + C language executor C-language executor additional SRAM Middle-Level Task of C Language Executor Custom software (Total amount of each path) 192KByte addition 256KByte 512KByte 1MByte 2MByte 3Mbyte J888 J734 J738 #256K J738 #512K J738#1M J738#2M J738#3M Custom software 4MByte J738#4M (Total amount of each path) 5MByte J738#5M FANUC PICTURE FANUC PICTURE function for non-touch panel display FANUC Auto HMI-NC 6MByte J738#6M 8MByte J738#8M - - Coordinate system shift - - - - Direct input of coordinate system shift - - - - Embedded macro S879 S944 R572 S652 #128K Small-hole peck drilling cycle J896 - - - - Canned cycles for grinding for grinding machine J640 Real time custom macro Pattern data input Program coordinate system changing function M code protect function MANUAL GUIDE i C Language Executor is FANUC PICTURE is Integrated Operation & Programming guidance function S842 J884 S607 - - - - MANUAL GUIDE i Multi path lathe S786 - - - - R594 S790 (8) MANUAL GUIDE i Tilted Working Plane Machining function MANUAL GUIDE i Extended Axis Name function S788 - - S789 Auxiliary/Spindle speed function Auxiliary function M8 digit 2nd auxiliary function B8 digit J920 Auxiliary function lock

5 High-speed M/S/T/B interface Waiting function Multiple command of auxiliary function 3 Spindle speed function S5 digit, binary output Spindle serial output S5 digit, serial output (max. 8 spindles) J850 - - - - - - Constant surface speed control Spindle override 0-254% Actual spindle speed output J855 J856 Spindle orientation 1 spindle J853 - - - - - - - - - - Spindle orientation expansion Max. 8 spindles J861 - - - - - - Max. 6 spindles - - - - Max. 2 spindles - - - - - - Spindle output switching function 1 spindle J854 Spindle output switching function Max. 8 spindles J862 - - - - - - expansion Max. 6 spindles - - - - Spindle synchronous control Simple spindle synchronous control Multi spindle control Spindle positioning Rigid tap Max. 2 spindles - - - - - - J858 J748 J859 J851 J828 Rigid tapping by manual handle J651 - - Arbitrary position reference setting for CS axis M code group check Spindle speed fluctuation detection Spindle control with servo motor Spindle control with Cs contour control Servo/spindle synchronous control Spindle switching function Spindle control switching function for High-speed cycle machining S664 - - J922 J857 J978 J985 S619 R515 R608 - - Spindle tandem control Spindle serial output is S648 - - Thread Start Position Compensation in Changing Spindle Speed function Tool function/tool compensation S946 (8) Tool function T7+1/T6+2/T5+3 - - - - Tool function T8 digit - - - - Tool offset pairs (Note) Specify total of tool offset pairs of each path. (Max. 999-pairs per each path) Max. digit of tool offset is 9. 32-pairs 64-pairs 99-pairs 200-pairs 400-pairs J925 J926 J927 J928 499-pairs S614 - - 999-pairs J721 - - 2000-pairs S622 - - Tool offset memory B Geometry/wear memory S616 - - - - Distinction between geometry and Tool offset memory C wear, or between cutter and tool J937 - - - - length compensation. Common offset memory between each path Only for more than 2 path control Tool length offset - - - - Tool offset Only for more than 2 path control S5 digit, serial output (max. 6 spindles) S5 digit, serial output (max. 2 spindles) High-speed cycle cutting function, High-speed cycle machining operation information output function and Cs contour contol are S617 Tool center point control S677 - - Tool posture control Tool center point control is S994 - - - - Tool center point control and Tool Cutting point command S996 - - - - - - offset memory C are Smooth TCP R639 - - (8) Y-axis offset J934 - - - -

5 4th/5th axis offset R517 - - - - Tool radius Tool nose radius compensation Tool radius Tool nose radius Automatic tool nose radius compensation S942 - - - - compensation is J930 3-dimensional tool compensation J727 - - - - - Cutting point interpolation for cylindrical interpolation S674 - - Tool geometry/wear compensation J931 - - - - Tool geometry/wear compensation 2nd Geometry Tool Offset J980 - - - - is required Tool pair for tool management function: 64 pairs Tool pair for tool management function: 240 pairs Tool pair for tool management function: 1000 pairs Tool management function: Customized data expansion(5 20) Tool management function: Customized data expansion(5 40) Tool management expansion Tool management function for oversize tools Tool management tool attachment/detachment function Tool management expansion B 64 tools S830 240 tools S831 1000 tools S833 Tool offset value counter input - - - - S834 S835 S852 S602 S997 R616 Tool length measurement - - - - Automatic tool length measurement S618 - - - - High speed measuring position reach signal input S998 - - Tool length/work zero point measurement J668 - - - - - Automatic tool offset J932 - - - - Direct input of tool offset value measured - - - - Direct input of offset value measured B J933 Rotary table dynamic fixture offset S728 - - - - - Changing Active Offset Value with Manual Move Tool length compensation in tool axis direction S825 S670 - - - - - - 3-dimensional cutter compensation S667 - - Work setting error compensation S993 - - Wheel wear compensation J633 - - - - - Direct input of offset value measured B for 2 spindle lathe Tool life management Addition of tool pairs for tool life management Automatic alteration of tool position compensation Tool offset for Milling and Turning function Accuracy compensation function Backlash compensation Backlash compensation for each rapid traverse and cutting feed Smooth backlash compensation Stored pitch error compensation Interpolation type pitch error compensation Bi-directional pitch error compensation Extended bi-directional pitch error compensation Max. 1024 pairs Tool offset memory C(milling path), Tool geometry/wear compensation (turning path) are Stored pitch error compensation is Stored pitch error compensation is Stored pitch error compensation, Bidirectional pitch error compensation are J686 - - - - J935 J936 J690 - - - - R595 J841 S644 S656 S657

5 Periodical secondary pitch error compensation Inclination compensation Straightness compensation Interpolation type straightness compensation S634 - - J981 J747 S639 Stored pitch error compensation is 3-dimensional error compensation S666 - - Thermal Growth Compensation Along Tool Vector S860 - - Linear inclination compensation function R520 - - 3-dimensional machine position compensation Hobbing/Electric gear box Simple electric gear box R581 J779 Skip function for EGB axis J696 - - Electric gear box 2 pair S710 - - Electric gear box automatic phase synchronization S711 - - Spindle electric gear box S720 - - Flexible synchronous control S709 - - Automatic phase synchronization for Flexible synchronous control S611 - - Flexible synchronous control is Inter-Path Flexible synchronous control S610 - - Function for gas cutting machine Functions for gas cutting machine Only for 1path R535 - - - - - Automatic exact stop check Only for 1path R505 - - - - - Torch swing for gas cutting machine Only for 1path R506 - - - - - In-acceleration/deceleration signal Only for 1path R519 - - - - - Gentle curve cutting Only for 1path R504 - - - - - Corner control by feedrate Only for 1path R508 - - - - - Tool offset B Only for 1path R507 - - - - - Editing operation Part program storage size *3 (Note) Specify total of part program storage size of each path. of registerable programs 63 of registerable programs expansion 1 of registerable programs expansion 2 Part program editing Program protect 32Kbyte - - - - - - 64Kbyte 128Kbyte 256Kbyte 512Kbyte 1Mbyte 2Mbyte J943 J944 J945 J946 J947 J948 4Mbyte J949 - - 8Mbyte J959 - - Max. 1000 programs J953 Max 4000 programs J954 - - Key and program encryption J778 - - Extended part program editing Playback J879 Machining time stamp J964 - - Background editing Multi part program editing Memory card program edit & operation Stored pitch error compensation is Stored pitch error compensation is Stored pitch error compensation is 128points. Stored pitch error compensation is Flexible synchronous control is Including background editing only available on 15"and 10.4" display unit Max 63 programs. The tool on PC is required to convert and store files to memory card J956

5 Memory card program entry count extension Template program function Multi-path editing function Max. 1000 programs S995 R561 R615 High speed program management R647 (8) Setting and display Status display Clock function Current position display Program comment display Parameter setting and display Parameter check sum function Alarm display Alarm history display Operator message history display Operation history display Remote diagnostic Run hour and parts count display Actual cutting feedrate display Display of spindle speed and T code at all screens Directory display of floppy cassette Optional path name display Operating monitor screen Servo setting screen Only for more than 2 path control Load meter etc. Spindle setting screen Only for i series Servo waveform display Maintenance information screen Software operator's panel Software operator's panel general purpose switch Extended software operator's panel general purpose switch Machine operation menu Multi-language display Selection of Five Optional Language Dynamic display language switching Data protection key Protection of Data at Eight Levels English Japanese German French Spanish Italian Chinese Chinese(simplified characters) Korean Portuguese Dutch Danish Swedish Hungarian Czech Polish Russian Turkish included in Multi-Language display 4 types Erase CRT screen display Manual or Automatic *1 Parameter set supporting screen Machining condition selecting function Program name 31 characters External message or external data input is Machine remote diagnosis package + Ethernet (Function:Reading CNC/PMC status, etc.) Included in reader/puncher interface Software operator's panel is Included in software operator's panel general purpose switch AI contour control I or is J971 J960 J961 S844 J965 S839 S841 J970 J968 J967 S829 J969 J678 J962 J650 S691 S690 S689 S739 S849 R587 R521 S828 S637

5 Nano soothing, Machining condition Machining quality level adjustment R593 - - selecting function are required Help function Self-diagnosis function Periodic maintenance screen Display of hardware and software configuration Servo information screen Spindle information screen Graphic function touch panel control External touch panel interface Virtual MDI Key J972 J682 J685 S883 Ethernet Display function Only Stand-alone type R950 CNC screen dual display function CNC screen display for 19" LCD Data input/output Reader/puncher interface Reader/puncher interface Reader/puncher interface expansion of receiving buffer *11 Fast data server S884 R624 J900 J901 R511 S737 Data server buffer mode Fast data server is required J728 - - Data server explorer connection Fast data server is required R953 (8) External tool offset External machine zero point shift External message External data input External key input External workpiece number search 9999 External program number search 1-9999 Memory card input/output Screen hard copy *2 Power Mate CNC manager External I/O device control One touch macro call Automatic data backup Interface function Embedded Ethernet J910 J912 J911 J913 J674 J902 S655 J381 Fast Ethernet Option board is S707 PROFIBUS-DP master Option board is S731 PROFIBUS-DP slave Option board is S732 DeviceNet master Option board is S723 DeviceNet slave Option board is S724 FL-net Option board is J692 FL-net/Ethernet coexisting function Option board is R951 Enhanced Embedded Ethernet function R952 CC-Link Remote Device function Option board is R954 (8) Others Status output signal Control unit incorporated type display unit *8 *9 (Not available in 300i /310i /320i ) Reader/puncher (Ch.1) interface Reader/puncher (Ch.2) interface Only 1 path control/option board is required Including External tool offset, External tool offset, and External message. NC ready, servo ready, automatic operation, automatic operation start lamp, feed hold, reset, NC alarm, distribution end, rewinding, inch input, cutting, inposition, thread cutting, tapping, etc. 7.2" monochrome LCD 8.4" color LCD 10.4" color LCD 15" color LCD

5 Control unit dimensions for LCD unit mounted type (depth) Stand alone type display *8 *10 Stand alone type control unit (width) MDI unit Without option slots (depth 60mm except 15"LCD) Option 1 slots (depth 90mm except 15"LCD) Option 2 slots (depth 110mm except 15"LCD) 10.4" color LCD 15" color LCD CNC display unit for automotive Option 2 slots (width 60mm) Option 4 slots (width 90mm) Separate MDI (ONG small, horizontal type) *1 Separate MDI (ONG vertical type, horizontal type) Separate MDI (personal computer key Type A, width 290mm) Separate MDI (personal computer key Type B, width 400mm) Touch panel Only for 10.4", 15" LCD *9*10 *1 1st PMC path Max. step number ladder: 100000 2nd PMC path 3rd PMC path Max. step number ladder: 64000 Max. step number ladder: 64000 PMC/L function Max. step number ladder: 5000 - - - - - - 1st path PMC message display function 2nd path PMC message display function 3rd path PMC message display function I/O Link expansion 2nd channel I/O Link expansion 3rd channel I/O Link expansion 4th channel 128Kbyte 256Kbyte 128Kbyte 128Kbyte DI/DO points: addition 1024/1024 points DI/DO points: addition 1024/1024 points DI/DO points: addition 1024/1024 points S977 #128K S977 #256K S978 #128K S979 #128K S981 S985 Step sequence Only 1st PMC path S982 Nonvolatile PMC extra relay function Nonvolatile PMC data table area expansion (7KB) Nonvolatile PMC data table area expansion (10KB) Extended PMC ladder instruction function S986 - - - - - - S984 S967#7K S967 #10K R851 PMC Function Block function R852 (8) Standard operator's panel Machine interface (I/O Link) Max. DI/DO points: 4096/4096 points (FS30i ) 3072/3072 points (FS31i /32i ) (Note) If using more than 1024/1024 points, I/O Link expansion option is necessary. (For expanding 4096/4096 points, option board is ) I/O Link - AS-i converter 55 keys 55 keys + Pointing Device I/O Unit-MODEL A I/O Unit-MODEL B Operator's panel I/O module Power magnetics control I/O module Connection panel I/O module (DI/DO module, 2A output module, Analog input module) Connection panel I/O module type-2 (DI/DO module) Terminal type I/O module

5 Manual pulse generator Pendant type manual pulse generator Handy machine operator s panel With axis selection and magnification switches FANUC AC SERVO MOTOR i series Connectable servo motor FANUC AC SERVO MOTOR i series FANUC LINEAR MOTOR Li S series FANUC SYNCHRONOUS BUILT-IN SERVO MOTOR Di S series FANUC AC SPINDLE MOTOR i series Connectable spindle motor FANUC AC SPINDLE MOTOR i series FANUC BUILT-IN SPINDLE MOTOR Bi series FANUC-NSK SPINDLE UNIT series Connectable servo amplifier FANUC SERVO AMPLIFIER FANUC SERVO AMPLIFIER i series i SV series Separate type rotary/linear encoder with TTL rectangle A/B phase signal Separate detector interface unit (for full-closed control) Separate type rotary/linear encoder with FANUC serial interface Separate type rotary/linear encoder with analogue 1Vp-p A/B phase signal Input power supply Ambient temperature of unit *10 DC24V±10% LCD mounted type control unit, display unit for stand-alone type control unit At operating: 0-58 At nonoperating: -20-60 Stand alone type control unit At operating: 0-55 At nonoperating: -20-60 Ambient relative humidity *10 Normally: 75%RH or less (No dew, nor frost allowed) Short term (within one month): 95%RH or less(no dew, nor frost allowed) Vibration IEC68-2-6 conforming

Software of personal computer part in case of the CNC system which is 300i/ 310i /320i -MODEL A or connected with personal computer via HSSB(High Speed Serial Bus) Operating system Extended library Software packages Development tools s Windows XP Professional / Embedded *4 FOCAS2 *7 Option Basic operation package 2 Option CNC screen display function Option Ladder editing package Option Visual Studio.NET *4 Microsoft Corp..NET class library for 19" LCD Option Remarks Software of GUI part in case of the CNC system which is 300i s/310i s/320i s-model A s Operating system Extended library Software packages Development tools Windows CE.NET Windows Embedded CE 6.0 *4 FOCAS2 *7 CNC screen display function embedded Visual C++ 4.0, Visual Studio.NET Visual Studio 2005 (for CE6.0) *4 Microsoft Corp. Remarks Hardware of Windows CE GUI part of incorporated type 300i s/310i s/320i s-model A CPU Main memory File memory Monitor Ports Ambient temperature of unit Ambient relative humidity s Remarks MIPS CPU 128MBytes or 256MBytes CompactFlash card *4 Built-in 10.4" color TFT LCD (640x480 dots), or 12.1" color TFT LCD (800x600 dots), or 15.0" color TFT LCD (1024x768 dots) Touch panel Option PCMCIA x1 slot Ethernet (100BASE-TX) USB x2 Serial port (RS-232-C) x2 At operating: 0 ~58 At nonoperating: -20 ~60 Normally: 10%~75%RH or less Short term (within one month): 10%~90%RH or less (No dew, nor frost allowed) Serial ports are shared by CNC control and Windows control. *8 Hardware of HSSB(High Speed Serial Bus) and Required hardware of commercially available personal computer in case of the CNC system which is connected with the personal computer via HSSB(High Speed Serial Bus). CNC side interface Connecting cable s Personal computer side interface board Personal computer requirements PCI Bus and HSSB for 1 channel PCI Bus and HSSB for 2 channel Optical fiber cable Option board in case of Display unit incorporated type Basicaly mounted in case of Display unit separate type CPU: Pentium or more PCI slot 1 or more Remarks For PCI slot in the personal computer Using voltage: +5V only Max. length: 100m For environmental requirements of the personal computer, refer to the manual supplied with the machine.

Software of Simulator for PC s NCGuide NCGuidePRO Remarks 1 user :A08B-9010-J730#ZZ11 10 users:a08b-9010-j731#zz11 20 users:a08b-9010-j732#zz11 30 users:a08b-9010-j733#zz11 For Windows 2000/XP PRO 1 user :A08B-9010-J735#ZZ11 Including a CD-R and a protection unit 10 users:a08b-9010-j736#zz11 20 users:a08b-9010-j737#zz11 30 users:a08b-9010-j738#zz11 Hardware of PANELi used in 300i /310i /320i -MODEL A s CPU Main memory External storage Monitor Ports CNC interface Extension slot Ambient temperature of unit Ambient relative humidity Pentium M, Celeron M, Celeron *4 Max. 1GBytes (Max. 512MBytes for Celeron) Hard disk(40gbytes) (Windows XP Professional) CompactFlash cards(master: 2GBytes + Slave: Max. 2GBytes) (Windows XP Embedded) 10.4" color TFT LCD (800x600 dots), 15.0" color TFT LCD (1024x768 dots), or 19.0" color TFT LCD (1280x1024 dots) Touch panel PCMCIA x1 slot Full keyboard x1 / Mouse x1 Serial (RS-232C) x2 / Parallel x1 ATAPI x2 *13 Floppy disk x1 *13 Ethernet (100BASE-TX) USB x2 (rear), USB x1 (front) High-Speed Serial Bus (Optical fiber cable) PCI spec. extension slot *13 (Short card size) x2 (Windows XP Professional) ( ditto ) x1 (Windows XP Embedded) At operating: 5 ~45 (Windows XP Professional) : 0 ~58 (Windows XP Embedded) At nonoperating: -20 ~60 Normally: 10%~75%RH or less Short term (within one month): 10%~90%RH or less (No dew, nor frost allowed) Wet Humidity: 29 or less Option Remarks Display Max. 65536 colors Touch panel is connected to serial port 1. Max. length: 100m *8 *6 Hardware of Display Unit fori s series CNC used in 300i s/310i s/320i s-model A s Remarks CPU Main memory File memory MIPS CPU 128MBytes or 256MBytes CompactFlash card *4 Built-in 10.4" color TFT LCD (640x480 dots), or Monitor 12.1" color TFT LCD (800x600 dots), or *8 15.0" color TFT LCD (1024x768 dots) Touch panel Option PCMCIA x1 slot Ports Ethernet (100BASE-TX) USB x2 Ambient temperature of unit At operating: 0 ~58 At nonoperating: -20 ~60 Normally: 10%~75%RH or less Ambient relative humidity Short term (within one month): 10%~90%RH or less (No dew, nor frost allowed)

(Note) *1 : There are some limitations in case of 300i /310i /320i /300i s/310i s/320i s-model A. *2 : In case of 300i /310i /320i /300i s/310i s/320i s-model A, this function can not be used. *3 : The part program storage size is a value of "Maximum program size when one program is registered". The total value of the program size that can be registered decreases when two or more programs are registered. (The actual registrable value might changes according to the registered number of programs and the program sizes.) *4 : Intel, Pentium are registered trademarks of Intel Corporation. Celeron is the trademark of Intel Corporation. MIcrosoft, Windows, VIsual Studio, and embedded Visual Tools logo are registered trademarks of Microsoft Corporation. CompactFlash is registered trademark of SanDisk Corporation. Each company's name and product's name is the trademark or registered trademark. *6 : Extension Board for IBM PC should be prepared by MTB. *7 : FOCAS2 = FANUC Open Cnc API version 2 *8 : LCD is manufactured by using high precision technology, however it has points which are always bright or dark. This phenomenon is caused by LCD's structure, and not defects. *9 : Please refer to page 16 for hardware of LCD-mounted type 300i s/310i s/320i s-model A. *10 : Please refer to page 17 for PANELi used in 300i /310i /320i -MODEL A and Hardware of Display Unit fori s series CNC used in 300i s/310i s/320i s-model A. *11 : In case of 300i s/310i s/320i s-model A and 30i /31i /32i -MODEL A with 15" LCD (LCD-mounted type), this function can not be used. *12 : The FOCAS2 interface is only provided. The animation software should be prepared by MTB. *13 : In case of 19" LCD type these ports or expansion slot do not exist. *14 : Pay attention that each kind of optical fiber cable is different in maximum length.

FANUC LTD Headquarters Oshino-mura, Yamanashi 401-0597, Japan Phone: 81-555-84-5555 Fax: 81-555-84-5512 http://www.fanuc.co.jp America Asia and Oceania GE Fanuc Intelligent Platforms, Inc. Tel 1-434-978-5000 Fax 1-434-978-5320 FANUC KOREA CORPORATION Tel 82-55-346-0122 Fax 82-55-346-2548 FANUC AMERICA CORPORATION Tel 1-847-898-5000 Fax 1-847-898-5001 FANUC TAIWAN LIMITED Tel 886-4-2359-0522 Fax 886-4-2359-0771 Europe, the middle east and Africa BEIJING-FANUC Mechatronics CO., LTD. Tel 86-10-6298-4726 Fax 86-10-6298-4741 FANUC GE CNC Europe S.A. Tel 352-727979-1 Fax 352-727979-214 FANUC INDIA PRIVATE LIMITED Tel 91-80-2852-0057 Fax 91-80-2852-0051 FANUC EUROPE GmbH Tel 49-7158-187100 Fax 49-7158-187111 FANUC THAI LIMITED Tel 66-2-662-6111 Fax 66-2-662-6120 FANUC GERMANY SERVICE GmbH Tel 49-7158-187300 Fax 49-7158-187411 FANUC MECHATRONICS (MALAYSIA) SDN. BHD. Tel 60-3-7628-0110 Fax 60-3-7628-0220 FANUC FRANCE SERVICE S.A.S Tel 33-1-4569-6333 Fax 33-1-4569-0325 PT. FANUC INDONESIA Tel 62-21-4584-7285 Fax 62-21-4584-7288 FANUC U.K. SERVICE LIMITED Tel 44-1895-634182 Fax 44-1895-676140 FANUC SINGAPORE PTE. LTD. Tel 65-6-567-8566 Fax 65-6-566-5937 FANUC ITALIA SERVICE S.p.A. Tel 39-02-4887-291 Fax 39-02-4571-3566 FANUC OCEANIA PTY. LIMITED Tel 61-2-8822-4600 Fax 61-2-8822-4666 FANUC IBERIA SERVICE S.A. Tel 34-93-664-4820 Fax 34-93-665-0695 FANUC PHILIPPINES CORPORATION Tel 63-2-813-3155 Fax 63-2-813-3157 FANUC TURKEY SERVICE LTD Tel 90-216-3913548 Fax 90-216-3918133 FANUC VIETNAM LIMITED Tel 84-8-3824-6638 Fax 84-8-3824-6637 FANUC BULGARIA SERVICE CORPORATION Tel 359-2-963-3319 Fax 359-2-963-2873 FANUC HONG KONG LIMITED Tel 852-2375-0026 Fax 852-2375-0015 FANUC CZECH SERVICE s.r.o. Tel 420-234-072-950 Fax 420-234-072-960 FANUC HUNGARY SERVICE kft Tel 06-23-507-400 Fax 06-23-507-401 FANUC SOUTH AFRICA (PROPRIETARY) LIMITED Tel 27-11-392-3610 Fax 27-11-392-3615 FANUC AUTOMATION LLC Tel 7-495-956-9780 Fax 7-495-956-9785 All specifications are subject to change without notice. No part of this catalog may be reproduced in any form. The products in this catalog are controlled based on Japan's "Foreign Exchange and Foreign Trade Law". The export of Series 30i/300i/300is-A and Series 31i/310i/310is-A5 from Japan is subject to an export License by the government of Japan. Other models in this catalog may also be subject to export controls. Further, re-export to another country may be subject to the license of the government of the country from where the product is re-exported. Furthermore, the product may also be controlled by re-export regulations of the United States government. Should you wish to export or re-export these products, please contact FANUC for advice. FANUC LTD, 2003 F30i-A(SpecE)-08, 2008.10, Printed in Japan