CRESTRON SITE PACK, LAST REVISION: 25/01/2017
CABLING INORFMATION IT IS ESSENTIAL THAT THE FOLLOWING INFORMATION IS READ AND UNDERSTOOD TO ENSURE THE SYSTEMS SUPPLIED AND INSTALLED PERFORM TO THE HIGHEST STANDARD. 1: MAIN CONTRACTOR TO UNDERTAKE THE FOLLOWING: 1.1: ENSURE ALL SUB-CONTRACTORS ARE AWARE OF THE STANDARDS AS SET OUT HERE. 1.2: ENSURE THAT ALL CABLES ARE STORED IN DRY SURROUNDINGS AT TEMPERATURES NOT LOWER THAN 5C. 1.3: NOTIFY WHEN ALL CABLING AND BACK BOXES HAVE BEEN INSTALLED AND CUT OUTS HAVE BEEN MADE FOR S SO TESTING AND CERTIFICATION CAN COMMENCE 2: ELECTRICAL CONTRACTOR TO UNDERTAKE THE FOLLOWING: 2.1: INSTALL ALL ULTRA LOW VOLTAGE ELECTRICAL CABLING TO THE CORRECT POSITIONS AS INDICATED WITHIN THIS SITE PACK. 2.2: ALL CABLING TO BE CLEARLY LABELLED AT BOTH ENDS ONLY WITH THE CABLE S SHOWN WITHIN THIS SITE PACK - FAILURE TO CORRECTLY LABEL THE CABLING MAY RESULT IN ADDITIONAL CHARGES BEING MADE TO THE CLIENT. 2.3: SUPPLY AND FIT ALL BACK BOXES AS DETAILED WITHIN THIS SITE PACK. NOTE THAT HEIGHTS AND POSITIONS OF BACK BOXES ARE INDICATED WITHIN THIS SITE PACK BUT ARE SUBJECT TO CONFIRMATION BY THE ARCHITECT. 2.4: CUT OUT ALL IN-CEILING AND IN-WALL POSITIONS AS INDICATED WITHIN THIS SITE PACK - CUT OUT DETAILS WILL BE PROVED UPON REQUEST. 2.5: INSTALL ANY ADDITIONAL MAINS SUPPLIES AS INDICATED WITHIN THIS SITE PACK. 2.6: IN THE CASE OF A LIGHTING CONTROL SYSTEM OR MAINS VOLTAGE RELAYS/CONTROLS, THE ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR ALL TERMINATIONS OF THE HIGH VOLTAGE SYSTEMS IN LINE WITH CURRENT BUILDING/ELECTRICAL REGULATIONS. 2.7: LEAVE ALL CABLES LOOSELY COILED 1M ABOVE FFL (FINISHED FLOOR LEVEL) TO AVO CRUSHING, DAMP, AND COLD. 3: WE ASK THAT THE FOLLOWING STANDARDS ARE FOLLOWED TO ENSURE THE PERFORMANCE OF THE STRUCTURED CABLING: 3.1: IN ORDER TO REDUCE ELECTRO-MAGNETIC INTERFERENCE, ALL ULTRA LOW VOLTAGE CABLING IS TO BE RUN AT LEAST 500MM FROM ANY LOW VOLTAGE (MAINS 120-230V) CABLING. 3.2: WHERE ULTRA LOW VOLTAGE CABLING CROSSES LOW VOLTAGE CABLING (MAINS 120-230V), IT SHOULD SO AT 90 DEGREES (RIGHT ANGLES). 3.3: IT IS NOT RECOMMENDED THAT ANY ULTRA LOW VOLTAGE CABLING IS BENT AT A RADIUS OF LESS THAN 60MM. 3,4: NO ULTRA LOW VOLTAGE CABLING SHOULD BE EXPOSED TO A PULLING TENSION IN EXCESS OF 10N. 3.5: UNLESS OTHERWISE INDICATED, AT EQUIPMENT POSITIONS/HEAD END, AT LEAST 5M OF SPARE CABLE SHOULD BE LEFT (FROM FLOOR OR CEILING LEVEL). 3.6: UNLESS OTHERWISE INDICATED, PLEASE LEAVE 1M OF SPARE CABLE AT ANY WALL OUTLET/CONTROL POINT. 3.7: AT CEILING LOCATIONS, PLEASE LEAVE 1M OF SPARE CABLE UNLESS OTHERWISE INDICATED - PLEASE LEAVE 2M LOOPS WHERE LOOPS ARE INDICATED. 3.8: IT IS NOT RECOMMENDED THAT ANY OPTICAL FIBRE CABLE IS BENT AT A RADIUS OF LESS THAN 200MM. 3.9: IT IS RECOMMENDED THAT OPTICAL FIBRE CABLE IS ONLY CUT WITH APPROVED FIBRE CUTTING TOOLS. OPTICAL FIBRE BEND RADIUS = 200MM NO ALTERATIONS ARE TO BE MADE WITHOUT PRIOR CONSULTATION. EXPLANATION OF CABLE TEXT ELEMENTS: CABLE : AA-S-02 LOWEST FLOOR (A) TOP LEFT ROOM (A) CABLE (S) NUMBER (02) CABLE TYPE: 2 2 CORE CABLE CABLE DESTINATION: HE: AV AUDIO/VEO HEAD END EXPLANATION OF S TWO TEXT ATTRIBUTES ARE USED TO DESCRIBE S AS SHOWN: NAME =DEVICE OPTIONS LCR-LCR BAR S-SUBWOOFER ST-STEREO SIVIOA BLINDS CABLE BEND RADIUS = 90MM = = DEVICE OPTIONS - KEY DESCRIPTION OF THE TECHNOLOGY UNIQUE TO EACH, SEE ABOVE FOR EXAMPLES AND MAIN LEGEND FOR DEVICE OPTIONS FOR EACH REFERENCE ALPHANUMERIC CHARACTERS ENTIFYING THE. FORMAT XX-YY-00 XX = ROOM (FLOORS ARE LABELLED WITH A LETTER STARTING WITH A FOR THE LOWEST FLOOR, ROOMS ARE GIVEN A LETTER STARTING WITH A FOR TOP LEFT ROOM THEN GOING IN ROWS AS IF READING A BOOK, SO AA IS TOP LEFT ROOM ON THE LOWEST FLOOR). YY = ITEM CODE (SP =, KP = KEYPAD, DT = DIGITAL TELEVISION, ETC.). 00 = UNIQUE ITEM NUMBER (01-99) E.G AA-SP-01 = LOWEST FLOOR/TOP LEFT ROOM--1 RG6 COAXIAL CABLE BEND RADIUS = 65MM CONTROL CABLE BEND RADIUS = 65MM CAT6E CABLE - BEND RADIUS = 48MM 2 & 4 CORE CABLE BEND RADIUS = 35MM AUDIO SIGNAL CABLE BEND RADIUS = 25MM NOTE: THIS DIAGRAM IS ONLY FOR USE ON A1 AUDIO SIGNAL CABLE BEND RADIUS = 25MM THREE SHAPE OUTLINES ARE USED TO DESCRIBE THE MOUNTING OF EACH DEVICE AS SHOWN: CEILING WALL FLOOR MOUNTING OPTIONS ON CEILING OR CUT INTO CEILING ON OR IN WALL HEIGHT AS INDICATED IN ELEVATIONS OR AS MARKED IN FLOOR OR FREESTANDING EXAMPLES: + MOUNTING OPTION NAME MOUNT TYPE 2 & 4 CORE CABLE BEND RADIUS = 35MM CAT6E CABLE -BEND RADIUS = 48MM RG6 COAXIAL CABLE BEND RADIUS = 65MM CONTROL CABLE BEND RADIUS = 65MM SIVIOA BLINDS CABLE BEND RADIUS = 90MM Preliminary - not for construction CEILING WALL FLOOR ITEMS THAT WILL NOT BE INSTALLED BUT STILL REQUIRE WIRES RUNNING FOR FUTURE USE OR INSTALLATION ARE INDICATED WITH A BLACK SURROUNDING BOX AS SHOWN BELOW: NAME PRE-WIRE = DEVICE OPTIONS ALL DEVICE OPTIONS AS PER MAIN S OPTICAL FIBRE BEND RADIUS = 200MM Cabling Information 1:1@A1 05/10/2016 KJ KA YB-02-C 2/14
BEND RADIUS FOR OPTICAL FIBRE = 200MM LARGER THAN THIS A3 SHEET SIZE ALLOWS SIVIOA BLINDS CABLE BEND RADIUS = 90MM RG6 COAXIAL CABLE BEND RADIUS = 65MM CONTROL CABLE BEND RADIUS = 65MM CAT6E CABLE - BEND RADIUS = 48MM 2 & 4 CORE CABLE BEND RADIUS = 35MM AUDIO SIGNAL CABLE BEND RADIUS = 25MM NOTE: THIS DIAGRAM IS ONLY FOR USE ON A3 AUDIO SIGNAL CABLE BEND RADIUS = 25MM 2 & 4 CORE CABLE BEND RADIUS = 35MM CAT6E CABLE -BEND RADIUS = 48MM RG6 COAXIAL CABLE BEND RADIUS = 65MM CONTROL CABLE BEND RADIUS = 65MM Preliminary - not for construction SIVIOA BLINDS CABLE BEND RADIUS = 90MM A3 Bend Radii 1:1@A3 05/10/2016 KJ KA YB-02-C 3/14
AUDIO VEO S NAME =DEVICE OPTIONS LCR-LCR BAR S-SUBWOOFER ST-STEREO VEO DISPLAY M-MIRROR TV WP-WEATHERPROOF TV LCD-LIQU CRYSTAL DISPLAY VEO DLP-DIGITAL LIGHT PROCESOR PROJECTOR LED-LIGHT EMITTING DIODE PROJECTION SCREEN F-FIXED M-MOTORISED COMMUNICATIONS S NAME =DEVICE OPTIONS PHONE AND DATA PORT D-DATA F-FIBRE OPTIC P-PHONE INCOMING SERVICES RF REPEATER ACCESS POINT CTV-CABLE TV P-PHONE S-SATELLITE CR-CELLUAR PR-PHONE WAP-WIRELESS ACCESS POINT CONTROL S NAME =DEVICE OPTIONS AA-S-02 HE:AV 2 AA-S-01 HE:AV 2 AA-V-01 HE:AV DIGITALMEDIA AA-C-01 HE:AV DIGITALMEDIA AA-D-01 HE:AV DIGITALMEDIA AA-R-01 HE:AV COAX AB-C-01 HE:AV DIGITALMEDIA AB-C-02 HE:AV DIGITALMEDIA AB-S-02 HE:AV 2 AB-S-01 HE:AV 2 AB-V-11 HE:AV DIGITALMEDIA AB-C-05 HE:AV DIGITALMEDIA AB-D-07 HE:AV DIGITALMEDIA AB-R-01 HE:AV COAX WTH: DEPTH: AC-D-03 AC-D-02 AC-S-01 AC-S-02 AC-R-01 AC-D-01 AC-C-03 AC-V-02 307.9999 MM 126 MM KEYPAD TOUCH PANEL RACK OR AV-AUDIO/VEO HEAD END C-CONTROL D-DATA SEC-SECURITY A-ARTICULATED LIFT/MOUNT M-MOTORISED UB-UNDER BED CEILING M-MASTER WLS-WIRELESS FT-FLIP TOP WLS-WIRELESS FURNISHINGS S NAME =DEVICE OPTIONS MOUNTING OPTIONS ON CEILING OR CUT INTO CEILING TV AA-TV-01 AA-KP-01 AA-SP-01 AA-K-01 AA-SP-02 AA-KP-02 TV AB-TV-01 M AB-PL-01 AC-SP-01 AC-SP-02 DV TV AC-TV-01 WALL FLOOR ON OR IN WALL HEIGHT AS INDICATED IN ELEVATIONS OR AS MARKED IN FLOOR OR FREESTANDING EXAMPLES: + MOUNTING OPTION NAME MOUNT TYPE WTH: 245.999 MM DEPTH: 117 MM AE-S-01 HE:AV 2 AE-S-02 HE:AV 2 HEIGHT: 1926.9989 MM WTH: 1242.9998 MM DEPTH: 686.0007 MM AMPS: 45.00 ST AE-SP-01 AE-K-01 AG-K-01 AG-KP-01 AB-K-01 AV AB-RA-01 AV AB-RA-03 AB-2-01 AE-KP-01 AB-KP-01 AB-K-02 AA-K-02 AB-KP-02 AB-SP-01 AB-SP-02 AB-K-03 AB-TP-01 C AB-EN-01 WAP AC-AP-01 AC-KP-01 AC-K-03 AC-K-01 AC-KP-03 AC-KP-02 AC-K-02 AF-K-01 AF-KP-01 PRE-WIRE CEILING WALL FLOOR CEILING PRE-WIRE ONLY NO CUTOUT AG-SP-01 AG-SP-02 AG-S-01 HE:AV 2 AG-S-02 HE:AV 2 AB-5-01 ROOF AB-5-02 ROOF AB-D-05 HE:BT AB-D-06 HE:BT AB-C-04 AB-C-03 COAX 5 CORE COAX 5 CORE DIGITALMEDIA DIGITALMEDIA HEIGHT: 1574.8 MM WTH: 647.7 MM DEPTH: 101.6 MM AMPS: 63.00 Preliminary - not for construction Plans Ground Floor - A 1:50@A1 05/10/2016 KJ KA YB-02-C 4/14
AUDIO VEO S NAME =DEVICE OPTIONS LCR-LCR BAR S-SUBWOOFER ST-STEREO VEO DISPLAY M-MIRROR TV WP-WEATHERPROOF TV LCD-LIQU CRYSTAL DISPLAY VEO DLP-DIGITAL LIGHT PROCESOR PROJECTOR LED-LIGHT EMITTING DIODE PROJECTION SCREEN PHONE AND DATA PORT INCOMING SERVICES RF REPEATER ACCESS POINT F-FIXED M-MOTORISED COMMUNICATIONS S NAME =DEVICE OPTIONS D-DATA F-FIBRE OPTIC P-PHONE CTV-CABLE TV P-PHONE S-SATELLITE CR-CELLUAR PR-PHONE WAP-WIRELESS ACCESS POINT CONTROL S NAME =DEVICE OPTIONS KEYPAD TOUCH PANEL M-MASTER WLS-WIRELESS FT-FLIP TOP WLS-WIRELESS BA-K-12 HE:C BA-S-02 HE:AV 2 BA-S-01 BA-V-02 BA-C-01 HE:AV DIGITALMEDIA BA-T-02 HE:AV DIGITALMEDIA BA-R-01 HE:AV COAX TV BA-TV-01 BF-K-01 BB-S-02 BB-S-01 BB-C-02 BB-C-01 BB-R-01 BB-D-01 BB-C-03 BB-V-02 FURNISHINGS S NAME =DEVICE OPTIONS RACK OR AV-AUDIO/VEO HEAD END C-CONTROL D-DATA SEC-SECURITY A-ARTICULATED LIFT/MOUNT M-MOTORISED UB-UNDER BED CEILING MOUNTING OPTIONS ON CEILING OR CUT INTO CEILING DV WALL ON OR IN WALL HEIGHT AS INDICATED IN ELEVATIONS OR AS MARKED BA-SP-01 BA-KP-01 BA-K-02 BA-SP-02 BB-SP-02 BB-KP-01 BB-K-02 BB-SP-01 BB-KP-02 BB-TP-01 TV BB-TV-01 BB-KP-03 FLOOR EXAMPLES: + MOUNTING OPTION NAME MOUNT TYPE IN FLOOR OR FREESTANDING CEILING BC-S-01 HE:AV 2 BC-S-02 HE:AV 2 BA-K-01 BC-KP-01 ST BC-SP-01 BC-K-01 BG-KP-02 BF-KP-01 BB-K-01 BB-K-03 BH-K-01 ST BD-SP-01 PRE-WIRE WALL FLOOR CEILING PRE-WIRE ONLY NO CUTOUT BG-KP-01 BG-SP-01 BG-K-01 BG-SP-02 BG-K-02 BH-KP-01 WAP BE-AP-01 WTH: 245.999 MM DEPTH: 117 MM BD-S-02 BD-S-01 BG-S-01 HE:AV 2 BG-S-02 HE:AV 2 BG-R-01 HE:AV COAX BG-D-01 HE:AV DIGITALMEDIA BG-C-01 BG-V-02 TV BG-TV-01 WTH: DEPTH: 308.0004 MM 125.9992 MM Preliminary - not for construction BE-C-01 BE-D-02 Plans First Floor - B 1:50@A1 05/10/2016 KJ KA YB-02-C 5/14
AUDIO VEO S NAME =DEVICE OPTIONS LCR-LCR BAR S-SUBWOOFER ST-STEREO VEO DISPLAY M-MIRROR TV WP-WEATHERPROOF TV LCD-LIQU CRYSTAL DISPLAY VEO DLP-DIGITAL LIGHT PROCESOR PROJECTOR LED-LIGHT EMITTING DIODE PROJECTION SCREEN PHONE AND DATA PORT INCOMING SERVICES RF REPEATER ACCESS POINT F-FIXED M-MOTORISED COMMUNICATIONS S NAME =DEVICE OPTIONS D-DATA F-FIBRE OPTIC P-PHONE CTV-CABLE TV P-PHONE S-SATELLITE CR-CELLUAR PR-PHONE WAP-WIRELESS ACCESS POINT CONTROL S NAME =DEVICE OPTIONS KEYPAD M-MASTER WLS-WIRELESS TOUCH PANEL FT-FLIP TOP WLS-WIRELESS CA-D-04 HE:AV CA-C-03 HE:AV CA-V-02 CA-C-02 HE:AV CA-C-01 HE:AV CA-K-01 HE:C DIGITALMEDIA DIGITALMEDIA DIGITALMEDIA DIGITALMEDIA CA-D-03 CA-D-02 CA-M-01 AB-D-03 FURNISHINGS S NAME =DEVICE OPTIONS RACK OR AV-AUDIO/VEO HEAD END C-CONTROL D-DATA SEC-SECURITY A-ARTICULATED LIFT/MOUNT M-MOTORISED UB-UNDER BED MOUNTING OPTIONS CA-KP-01 WTH: 289.9994 MM DEPTH: 69.9999 MM CEILING WALL ON CEILING OR CUT INTO CEILING ON OR IN WALL HEIGHT AS INDICATED IN ELEVATIONS OR AS MARKED FLOOR IN FLOOR OR FREESTANDING WAP CA-AP-01 CA-SP-03 CA-SP-09 CA-SP-05 CA-TP-01 CA-SP-07 CA-SP-11 EXAMPLES: + MOUNTING OPTION NAME MOUNT TYPE CEILING S CA-SU-02 WALL CA-FI-01 CA-SP-02 S CA-SU-01 CA-PR-01 PRE-WIRE FLOOR CEILING PRE-WIRE ONLY NO CUTOUT CA-SP-01 CA-SP-08 CA-SP-04 CA-SP-10 CA-SP-06 CA-S-01 CA-S-21 CA-S-02 CA-S-22 CA-S-03 CA-S-05 HE:AV 2 CA-S-09 CA-S-08 HE:AV 2 CA-S-04 HE:AV 2 CA-S-07 HE:AV 2 CA-S-11 HE:AV 2 CA-S-10 HE:AV 2 CA-S-06 HE:AV 2 Preliminary - not for construction Plans Loft - C 1:50@A1 05/10/2016 KJ KA YB-02-C 6/14
Preliminary - not for construction Plans Cinema 1:20@A1 05/10/2016 KJ KA YB-02-C 7/14
Preliminary - not for construction Elevations Cinema Screen Wall 1:20@A1 05/10/2016 KJ KA YB-02-C 8/14
Preliminary - not for construction Elevations Cinema Rear Wall 1:20@A1 05/10/2016 KJ KA YB-02-C 9/14
Preliminary - not for construction Elevations Cinema Right Wall 1:20@A1 05/10/2016 KJ KA YB-02-C 10/14
Preliminary - not for construction Elevations Cinema Left Wall 1:20@A1 05/10/2016 KJ KA YB-02-C 11/14
Preliminary - not for construction Elevations TV Kitchen, Master Bed, Beds 2, 3 & 4 05/10/2016 KJ KA YB-02-C 12/14
193 Preliminary - not for construction Elevations Touch Panel, Light Switches 05/10/2016 KJ KA YB-02-C 13/14
Preliminary - not for construction Elevations Dimming Panel 05/10/2016 KJ KA YB-02-C 14/14