Table of Contents. Quick Reference. Detailed Data Sheets. Mixer Terminology. Technical Article. Questions & Answers. References

Similar documents
Table of Contents. Quick Reference. Detailed Data Sheets. General Information. Questions & Answers. Technical Article. Technical Application MIXE MIXE

IQ Networks. Catalog Products (EAR99/Non-ITAR)

8 TO 18 GHz EVEN-HARMONIC (1/2 LO) BALANCED MIXER

INTEGRATED ASSEMBLIES MICROWAVE SOLUTIONS FROM TELEDYNE COUGAR

Features. = +25 C, IF= 100 MHz, LO = +17 dbm*

MICROLITHIC DOUBLE-BALANCED I/Q MIXER

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

MICROLITHIC DOUBLE-BALANCED I/Q MIXER

Features. = +25 C, As a Function of LO Drive

Features OBSOLETE. = +25 C, As a Function of LO Drive. LO = +13 dbm IF = 70 MHz

Features OBSOLETE. = +25 C, As a Function of LO Drive. LO = +10 dbm. IF = 70 MHz

MICROLITHIC DOUBLE-BALANCED I/Q MIXER

= +25 C, IF= 100 MHz, LO = +15 dbm*

HMC219AMS8 / 219AMS8E. Features OBSOLETE. = +25 C, As a Function of LO Drive. LO = +13 dbm IF = 100 MHz

= +25 C, IF= 100 MHz, LO = +15 dbm*

Parameter LO RF IF Min Typ Max Diode Option (GHz) (GHz) (GHz) LO drive level (dbm)

Parameter Min. Typ. Max. Min. Typ. Max. Units

= +25 C, IF= 100 MHz, LO = +17 dbm*

The Hmc869LC5 is ideal for: Point-to-Point and Point-to-Multi-Point Radio. Parameter Min. Typ. Max. Units

FMMX9000 DATA SHEET. Field Replaceable SMA IQ Mixer From 4 GHz to 8.5 GHz With an IF Range From DC to 3.5 GHz And LO Power of +15 dbm.

High-Value 100 Series (Outdoor)

Features OBSOLETE. = +25 C, As a Function of LO Drive. LO = +13 dbm IF = 100 MHz

Features. = +25 C, As a Function of LO Drive. LO = +10 dbm IF = 100 MHz

Features. Parameter Min. Typ. Max. Units

Features. Parameter Min. Typ. Max. Min. Typ. Max. Units

= +25 C, IF= 100 MHz, LO = +15 dbm*

Multiple Band Outdoor Block Up- and Downconverters

1.5 GHz to 4.5 GHz, GaAs, MMIC, Double Balanced Mixer HMC213BMS8E

OBSOLETE HMC908LC5 MIXERS - I/Q MIXERS, IRMS & RECEIVERS - SMT. GaAs MMIC I/Q DOWNCONVERTER 9-12 GHz. Typical Applications. Functional Diagram

Features. Gain Variation Over Temperature db/ C

Features. Parameter Min. Typ. Max. Units

Features OBSOLETE. LO = +19 dbm, IF = 100 MHz Parameter

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

GaAs MMIC High Dynamic Range Mixer

GaAs, MMIC Fundamental Mixer, 2.5 GHz to 7.0 GHz HMC557A

Features. = +25 C, IF= 1 GHz, LO= +13 dbm* Parameter Min. Typ. Max. Units

CMD180C GHz Fundamental Mixer. Features. Functional Block Diagram. Description

CMD179C GHz Fundamental Mixer. Features. Functional Block Diagram. Description

Features OBSOLETE. = +25 C, As an IRM. IF = MHz. Frequency Range, RF GHz. Frequency Range, LO

Parameter Min. Typ. Max. Min. Typ. Max. Units

10 GHz to 26 GHz, GaAs, MMIC, Double Balanced Mixer HMC260ALC3B

Features. = +25 C, IF= 1 GHz, LO= +13 dbm* Parameter Min. Typ. Max. Units

FMMX9004 DATA SHEET. Field Replaceable SMA IQ Mixer From 15 GHz to 23 GHz With an IF Range From DC to 3.5 GHz And LO Power of +17 dbm.

HIGH-LINEARITY TRIPLE-BALANCED MIXERS T3-0838

FMMX9002 DATA SHEET. Field Replaceable SMA IQ Mixer From 8.5 GHz to 13.5 GHz With an IF Range From DC to 2 GHz And LO Power of +19 dbm.

Parameter Symbol Units MIN MAX. RF Input Power (CW) Pin dbm +20. LO Input Power (CW) Pin dbm +27

Features. = +25 C, IF= 100 MHz, LO= +13 dbm* Parameter Min. Typ. Max. Min. Typ. Max. Units

6 GHz to 26 GHz, GaAs MMIC Fundamental Mixer HMC773A

GaAs DOUBLE-BALANCED MIXER

High Performance Outdoor Test Translators

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

CMD178C GHz Fundamental Mixer. Features. Functional Block Diagram. Description

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

FREQUENCY CONVERTER HIGH-PERFORMANCE OUTDOOR BLOCK UP AND DOWNCONVERTERS. Narda-MITEQ 1 FEATURES OPTIONS

Amplifier Systems. 1:1, Dual 1:1 and 1:2 Redundant Low-Noise. Back to

HP 71910A and 71910P Wide Bandwidth Receiver Technical Specifications

GaAs MMIC Double Balanced Mixer

CMD255C GHz High IP3 Fundamental Mixer. Features. Functional Block Diagram. Description

Instrumentation Grade RF & Microwave Subsystems

Features. = +25 C, IF= 100 MHz, LO= +15 dbm* Parameter Min. Typ. Max. Min. Typ. Max. Units

SATCOM FIBER OPTIC PRODUCTS

DOUBLE-BALANCED MIXERS M1-0008

TRIPLE-BALANCED MIXERS M2-0250

CMD183C GHz I/Q Mixer. Features. Functional Block Diagram. Description

Orbital 694XA Series. Ka BAND EXTERNAL REFERENCE LNB with rear anchor posts. Wide range of Frequencies and Bandwidths LNB 1855R 1000 XA-WN60

Features. = +25 C, As a Function of LO Drive & Vdd. IF = 1 GHz LO = -4 dbm & Vdd = +4V

HMC7053. Block Upconverters. Typical Applications. General Description. Features. Functional Block Diagram. Satellite communications.

Using Surplus 23 GHz Modules At MHz By Al Ward W5LUA

CMD257C GHz High IP3 I/Q Mixer. Features. Functional Block Diagram. Description

DUAL-, TRI- AND QUAD-BAND OUTDOOR BLOCK CONVERTERS

FREQUENCY CONVERTER. MULTIPLE OUTPUT WIDEBAND Ku AND Ka DOWNCONVERTERS. Narda-MITEQ FEATURES OPTIONS

HMC412MS8G / 412MS8GE

11 GHz MDD FIBER OPTIC LINK FEATURES TYPICAL APPLICATIONS

MICROLITHIC DOUBLE-BALANCED MIXER

OBSOLETE HMC215LP4 / 215LP4E. GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, GHz. Typical Applications. Features. Functional Diagram

Parameter LO RF IF Min Typ Max Diode Option (GHz) (GHz) (GHz) LO drive level (dbm)

Ka-Band Outdoor Block Upconverters and Low-Noise Block Downconverters

MICROLITHIC DOUBLE-BALANCED MIXER

MULTIBAND 1/3 RACK-MOUNTED

MICROLITHIC DOUBLE-BALANCED MIXER

Parameter Symbol Units MIN MAX. RF Input power (CW) Pin dbm +23

GaAs MMIC Double Balanced Mixer. Description Package Green Status

Features. = +25 C, 50 Ohm System

GaAs DOUBLE-BALANCED MIXER

Features OBSOLETE. = +25 C, IF = 1.45 GHz, LO = +13 dbm [1]

GaAs MMIC Double Balanced Mixer

MICROLITHIC DOUBLE-BALANCED MIXER

Orbital Ka-ISO. Ext Ref Ka LNB with integrated isolator. Orbital Research Ltd Marine Drive, White Rock, BC. Canada V4B 1A9

MICROLITHIC DOUBLE-BALANCED MIXER

FREQUENCY CONVERTER 1/3 RACK-MOUNTED BLOCK CONVERTER. Narda-MITEQ FEATURES OPTIONS. Unit shown with Option 17. Unit shown without Option 17

Features. = +25 C, LO = 0 dbm, Vcc = Vcc1, 2, 3 = +5V, G_Bias = +2.5V *

Short Form Product Catalog 2017

HMC581LP6 / 581LP6E MIXERS - SMT. HIGH IP3 RFIC DUAL DOWNCONVERTER, MHz. Typical Applications. Features. Functional Diagram

Data Sheet. AMMC GHz Image Reject Mixer. Description. Features. Applications. Absolute Maximum Ratings [1]

HMC7056. Block Upconverters / HPA's. Typical Applications. General Description. Features. Functional Block Diagram

OBSOLETE HMC7056. Block Upconverters / HPA's. Typical Applications. General Description. Features. Functional Block Diagram

GaAs MMIC High Dynamic Range Mixer

HMC485MS8G / 485MS8GE. Features OBSOLETE. = +25 C, LO = 0 dbm, IF = 200 MHz*, Vdd= 5V

Transcription:

Table of Contents Quick Reference Detailed Data Sheets Mixer Terminology Technical Article Questions & Answers References

TABLE OF CONTENTS CONTENTS CONTENTS INTRODUCTION IMAGE REJECTION/IQ DETECTOR Corporate Overview AND W NOISE FRONT-ENDS (CONT.) Technology Overview Low-Noise Image Rejection Specification Definitions CONTENTS Downconverter Assemblies Quality Assurance General Information MTBF Calculations Mixer Terminology Manufacturing IMAGE Flow REJECTION/IQ Diagrams DETECTOR Image Rejection Mixer, I/Q, Device 883 Screening AND W NOISE FRONT ENDS QIFM Circuits General Specifications Application-Driven Mixer Circuits Space-Qualified Application Mixers Guidelines Questions and Answers MIXERS Quick Reference Image Rejection Mixers/QIFMs LNA, Image Rejection Mixers Application Image Guidelines Rejection Mixers and BPSK and QPSK Phase Detectors Quick Reference Technical Article Single-, I/Q Double-Balanced Demodulators and Mixer Extended Dynamic Range Mixers with IF Amplifier Low-Noise Image Rejection Downconverter Ordering Information Double-Balanced, Biasable, Triple-Balanced Assemblies and and MESFET I/Q Demodulators Mixers MODULATORS Sub-Harmonic and Specialty Mixers Application Guidelines Detailed Detailed Data Data Sheets Sheets Quick Reference Double Image Balanced Rejection With IF Mixers Amplifiers and I/Q Demodulators Biphase Modulators and DSB Upconverters Double Balanced Ultra Broadband QPSK and QAM Modulators Double Enhanced Balanced Image High Isolation Rejection Mixers SSB Upconverters and Vector Double-Balanced Biasable Image Wide IF Rejection Bandwidth Mixers Modulators/Phase Shifters Double-Balanced Surface Mount Detailed Data Sheets Triple I/Q Balanced Phase Detector with Optional Biphase Modulators and DSB Upconverters Biasable Low Power QPSK and Modulation Driven Modulators MESFET Video High Amps Dynamic and/or Range Digital Output SSB Upconverters Even Image Harmonic Rejection 1/2 Mixers with Carrier Driven Active Multiplier Mixer General Information Waveguide Integrated IF Amplifiers Mixer Terminology Amplified Low-Noise Image Rejection Modulator Circuit Description in Sampling Mixer Order of Complexity General Downconverter Information Assemblies Modulators and Upconverters Double-Sideband Mixer Circuits Questions and Answers Double-Sideband General Information Mixer Subsystems Technical Application Questions Mixer and Terminology Answers High-Isolation Modulators Balanced Schottky Diode Mixers and High-Level Mixers for MESFET Image Mixers Rejection Mixer, I/Q, Communications Links Technical Article QIFM Circuits Ordering Information Fundamental, Harmonic and Sampling MESFET Application-Driven Mixer Circuits Mixer Circuits MULTIPLIERS Technical Application Introduction Ordering Questions Information and Answers Technical Overview Technical Discussion IMAGE Image REJECTION/IQ Rejection Mixers/QIFMs DETECTOR Design Example AND LNA, W NOISE Image FRONT Rejection ENDS Mixers Specification Definitions Application Guidelines Defining Multiplier Terms Quick BPSK Reference and QPSK Phase Detectors Typical Block Diagrams Image Technical Rejection Article Mixers and Specifications and Typical Values I/Q Demodulators Environmental Conditions Low-Noise Extended Image Dynamic Rejection Downconverter Range Mixers Percentage Bandwidth, Rejection and Size Assemblies and I/Q Demodulators Ordering Information Active Frequency Multipliers Detailed Data Sheets Common Applications Image Rejection Mixers and I/Q Demodulators Quick Reference Enhanced Image Rejection Mixers Passive Frequency Doublers Biasable Image Rejection Mixers Active Frequency Doublers I/Q Phase Detector with Optional Select Bandwidth Doublers and Triplers Video Amps and/or Digital Output Active Frequency Triplers Image Rejection Mixers with High Order Active Multipliers Integrated IF Amplifiers Comb Multiplier Designs

IMAGE REJECTION PRODUCTS This detailed image rejection mixer section summarizes the important input, output and transfer characteristics of these devices. This catalog is also published on our web site: http://www.miteq.com. We look forward to helping you choose the best mixer from our increasing core of state-of-the-art products, so that your system will be more competitive in today s demanding marketplace. Most importantly, we are committed to satisfying not only the written technical specifications of any new product, but to ensure that the product satisfies its intended application requirements. IMAGE REJECTION MIXER APPLICATION GUIDELINES CRITICAL SPECIFICATIONS BEST MODELS CIRCUIT DESCRIPTION Low cost/size IR, IRM octave bands Double balanced Limited power IRB, ARB series Biasable bridge quad Widest bandwidth IRA226 series 2 to 26 GHz, double balanced Narrowest bandwidth IR325HA1 1% double-tuned baluns Low I/Q DC offset IR52, IR14, IR28 Double balanced/tuned baluns Lowest conversion loss IR325HA1 3.5 db, tuned balun Lowest noise figure AR series MITEQ LNA front ends High image rejection IRE, ARE series Quadrature enhanced, 3 db typ. High IP 3, P1 db I series Double balanced MESFET, +33 dbm typical IF amplification IRA, IRBA series 25 db -to-if gain Integrated LNB series Block converter, triple balanced Millimeter, 1/2 ARE series Back-to-back ring quads TYPICAL PEORMANCE RANGES NOISE FIGURE (db) NOISE FIGURE (db) 4 3 2 1 NOISE FIGURE VS. FREQUENCY MODERATE BAND AMPLIFIERS 1 8 16 24 32 4 NOISE FIGURE VS. FREQUENCY MULTIOCTAVE BAND AMPLIFIERS 44 29 17 4 44 3 29 2 17 1 75 6 12 18 24 3 36 42 75 NOISE TEMPERATURE (K) NOISE TEMPERATURE (K) COMPRESSION (dbm) IMAGE REJECTION (db) +25 +2 +15 +1 +5 L MIXER COMPRESSION (INPUT) SCHOTTKY DIODES MESFET M +1 +15 +2 +25 POWER (dbm) IMAGE REJECTION LIMITS 3 (MODELS) ±(2 ), (.5 db) IRE618 I/Q PHASE, AMP ERROR 2 1 ±(1 ), (1 db) I/Q PHASE, AMP ERROR MINIMUM IR NEEDED TO LIMIT IMAGE NOISE TO <.4 db IRO218 6 12 18 24 H 165

IMAGE REJECTION MIXERS AND I/Q DEMODULATORS IR IF HYBRID VCC IR IR/IRM Image Rejection IRB Biasable Image Rejection IRE Enhanced Image Rejection FREQUENCY RANGE NOMINAL CONVERSION IMAGE - INPUT IF POWER SS REJECTION ISOLATION IP 3 MODEL AND (GHz) (dbm) (db) (db) (db) (dbm, Typ.) NUMBER (GHz) (Note 1) (Note 2) (Max.) (Typ./Min.) (Typ./Min.) (Note 2) NOTES PAGE IMAGE REJECTION MIXERS AND I/Q DEMODULATORS IR52LC1.5 2 DC.5 1 13 9.5 18 / 15 2 / 18 16 169 IR12LC1 1 2 DC.5 1 13 8 23 / 18 4 / 3 16 171 IR14LC1 1 4 DC.5 1 13 9.5 2 / 18 2 / 18 16 173 IRM24LC2 2 4 DC.5 1 13 7.5 25 / 18 3 / 2 16 175 IRM28LC2 2 8 DC.5 1 13 9 2 / 18 2 / 18 16 177 IRM48LC2 4 8 DC.5 1 13 8 23 / 18 3 / 2 16 179 IR78LI3Q 7.2 8.4 DC.25 1 13 1.5 3 / 25 3 / 25 15 181 IRM812LC2 8 12 DC.5 1 13 8 23 / 18 3 / 2 16 183 IRM118LC1 1 18 DC.5 1 13 11 2 / 15 2 / 18 16 185 IRM618LC2 6 18 DC.5 1 13 1 2 / 18 2 / 18 16 187 IRM218LC1 2 18 DC.5 1 13 11 2 / 18 2 / 18 18 189 IRM1218LC2 12 18 DC.5 1 13 1 2 / 18 23 / 2 16 191 IRM226LC1 2 26 DC.5 1 13 14.5 18 / 15 18 / 15 18 193 IR1826NI7 18 26 DC.5 16 18 1.5 17 / 15 25 / 2 17 195 IR264NI7 26 4 DC.5 16 18 1.5 17 / 15 2 / 15 17 197 IRJ8595U 8.5 9.5.2.2 7 9 8 25 / 18 35 / 3 14 199 IRJ8595L 8.5 9.5 8 16 7 9 8 25 / 18 35 / 3 14 21 ENHANCED IMAGE REJECTION MIXERS IRE28LI1 2 8.2.2 13 15 9.5 3 / 25 3 / 24 18 23 IRE618LI1 6 18.2.2 13 15 1.5 35 / 25 3 / 24 18 25 BIASABLE IMAGE REJECTION MIXERS IRB218LC1 2 18.2.2-1 +13 12.5 2 / 18 18 / 15 27 I/Q PHASE DETECTOR WITH OPTIONAL VIDEO AMPS AND/OR DIGITAL OUTPUT IQM162.15.17 Video 1 13 1 N/A N/A N/A 29 IQD/IQDD162.15.17 Video 1 13 3.5K N/A N/A N/A 29 GENERAL The output power capability of mixers (with and without LNAs) is chiefly determined by the power used. The specifications shown are mostly mixers using low-level Schottky diodes, but in all cases higher level H diodes are available requiring 1 db more power and yielding a proportional increase in IF output capability. For extremely high dynamic range, with limited power, MESFET mixers with DC bias can be used. Conversely, for applications requiring smallest power (-1 dbm), where high IF output power is not required, DC biased Schottky diode designs (IRB) are cost effective. I/Q demodulators (Q option) operate with output frequencies near DC and, therefore, do not use an IF hybrid. These units are otherwise similar to image rejection circuits with special emphasis on high -to- isolation which insures low DC output offset voltages. Each I and Q output will have 3 db more conversion loss than that of the combined image rejection unit. 166

W-NOISE IMAGE REJECTION DOWNCONVERTER ASSEMBLIES AND I/Q DEMODULATORS LNA LNA IMAGE FILTER IF HYBRID R L I IF SYSMM AR/ARM Low-Noise Image Rejection Mixer Assembly SYSMM Low-Noise Multiplied Mixer Assembly FREQUENCY RANGE NOMINAL -IF NOISE IMAGE OUTPUT IF POWER GAIN FIGURE REJECTION IP 3 MODEL AND (GHz) (dbm) (db) (db) (db) (dbm, Typ.) NUMBER (GHz) (Note 1) (Note 2) (Typ./Min.) (Max.) (Min.) (Note 2) NOTES PAGE IMAGE REJECTION MIXERS WITH INTEGRATED IF AMPLIFIERS IRBA226LC1 2 26.2.2-1 +13 2 / 15 16 (Typ.) 15 15 211 IRA226LC1 2 26.2.2 1 13 23 / 2 15 (Typ.) 15 2 213 IRA5459LR1 5.4 5.9.2.2 7 1 23 / 2 6 2 13 215 IRA8596LR1 8.5 9.6.2.2 7 1 23 / 2 6.5 2 13 217 W-NOISE IMAGE REJECTION DOWNCONVERTER ASSEMBLIES ARM24LC2 2 4.2.2 1 13 3 / 27 1.8 18 16 219 ARM28LC2 2 8.2.2 1 13 3 / 27 2.2 18 16 221 ARM48LC2 4 8.2.2 1 13 3 / 27 2 18 16 223 ARL5359LC2 5.3 5.9.2.2 1 13 33 / 3 3.5 18 16 Limiter 225 ARM812LC2 8 12.2.2 1 13 3 / 27 2.5 18 16 227 ARM618LC2 6 18.2.2 1 13 24 / 22 4 18 15 229 ARM1218LC2 12 18.2.2 1 13 3 / 27 3.5 18 16 231 AR1826LI8 18 26.2.2 16 18 38 / 31 3.3 18 1 233 AR264LI8 26 4.2.2 16 18 32 / 25 4 18 15 234 ARZ227 8.5 9.6.54.66-3 +3 33 / 32 1.2 25 17 235 ARZ991N1R 9.9 1.4.1.2 14 16 21 / 16 3 15 13 237 SBWA3435N1R 34.5 35.5.2.2 2 4 16 / 13 6 15 13 239 AR1314N1R 12-5 14.5 / 1.5 2 4 12 18 33 / 28 2.9 15 18 241 SYSMM1X332 3 32 / 28 2 4 1 14 3 / 25 2.8 15 17 243 SYSMM2X332 3 32 / 14 2 4 1 14 3 / 25 2.8 15 17 243 SYSMM3X332 3 32 / 9.33 2 4 1 14 3 / 25 2.8 15 17 243 SYSMM1X3436 34 36 / 32 2 4 1 14 37 / 31 3.3 15 17 245 SYSMM2X3436 34 36 / 16 2 4 1 14 37 / 31 3.3 15 17 245 SYSMM3X3436 34 36 / 1.67 2 4 1 14 37 / 31 3.3 15 17 245 SYSMM1X3638 36 38 / 34 2 4 1 14 37 / 31 3.3 15 17 247 SYSMM2X3638 36 38 / 17 2 4 1 14 37 / 31 3.3 15 17 247 SYSMM3X3638 36 38 / 11.33 2 4 1 14 37 / 31 3.3 15 17 247 SYSMM1X4345 43 45 / 41 2 4 11 14 29 / 24 4.5 15 17 249 SYSMM2X4345 43 45 / 2.5 2 4 11 14 29 / 24 4.5 15 17 249 SYSMM3X4345 43 45 / 13.67 2 4 11 14 29 / 24 4.5 15 17 249 167

This page is intentionally blank 168

.5 TO 2 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IR52LC1A, IR52LC1B, IR52LC1C AND IR52LC1Q FEATURES / coverage....5 to 2 GHz IF operation... DC to.5 GHz Conversion loss... 8.5 db typical Image rejection... 18 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz.5 2 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz.5 2 power range IR52LC1 dbm +1 +12 +13 IR52MC1 dbm +13 +15 +16 IR52HC1 dbm +17 +18 +2 VSWR Ratio 2.5:1 169 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 8.5 9.5 IR52LC1Q db 11.5 12.5 Single-sideband noise figure db 1 Image rejection (Note 1) < db 15 18 -to- isolation db 18 2 -to-if isolation db 2 Input power at 1 db compression IR52LC1 dbm +6 IR52MC1 dbm +1 IR52HC1 dbm +15 Input two-tone third-order intercept point IR52LC1 dbm +16 IR52MC1 dbm +2 IR52HC1 dbm +25 Amplitude balance IR52LC1Q db ±1.5 Phase balance IR52LC1Q Degrees ±1 Truth table IR52LC1Q Port < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IR52LC1A MHz 2 4 IR52LC1B MHz 4 8 IR52LC1C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IR52LC1Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 Revised: 6/18/12

IR52LC1 TYPICAL TEST DATA VSWR ( = +13 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 1 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 CONVERSION SS 2 3 IMAGE REJECTION 4 1:1 5 2.5.8 1.1 1.4 1.7 2.5.8 1.1 1.4 1.7 2 4 8 12 16 CONVERSION SS (db) AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 3 15 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) -15-3.5.8 1.1 1.4 1.7 2 2 1-1 -2.5.8 1.1 1.4 1.7 2 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C ISOLATION (db) 2 4 6 8 TO TO IF ISOLATION ( = +1 dbm) 1.5.8 1.1 1.4 1.7 2 GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). IR52LC1A, B and C OUTLINE DRAWINGS IR52LC1Q.5 [12.7] 1. [25.4].25 [6.35] IN 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IF OUT > IN < CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8] TERMINATE UNUSED IF OUTPUT.5 [12.7] 25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35].5 [12.7] 1. [25.4].25 [6.35] IN 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IN I Q CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8].5 [12.7] 25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35] IMAGE REJECTION NOTE: All dimensions shown in brackets [ ] are in millimeters. QIFM, I/Q DEMODULATOR 17

1 TO 2 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IR12LC1A, IRO12LC1B, IRO12LC1C AND IRO12LC1Q FEATURES / coverage... 1 to 2 GHz IF operation... DC to.5 GHz Conversion loss... 6.5 db typical Image rejection... 23 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 1 2 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 1 2 power range IR12LC1 dbm +1 +12 +13 IR12MC1 dbm +13 +15 +16 IR12HC1 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 6.5 8 IR12LC1Q db 9.5 11 Single-sideband noise figure db 8.5 Image rejection (Note 1) < db 18 23 -to- isolation db 3 4 -to-if isolation db 2 Input power at 1 db compression IR12LC1 dbm +6 IR12MC1 dbm +1 IR12HC1 dbm +15 Input two-tone third-order intercept point IR12LC1 dbm +16 IR12MC1 dbm +2 IR12HC1 dbm +25 Amplitude balance IR12LC1Q db ±1.5 Phase balance IR12LC1Q Degrees ±12.5 Truth table IR12LC1Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IR12LC1A MHz 2 4 IR12LC1B MHz 4 8 IR12LC1C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IR12LC1Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 171

IR12LC1B TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 6 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 IMAGE REJECTION CONVERSION SS CONVERSION SS (db) AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 1:1 1 1.2 1.4 1.6 1.8 2 3 1.5-1.5-3 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) 1 1.2 1.4 1.6 1.8 2. 25 12.5-12.5-25 1 1.2 1.4 1.6 1.8 2. ISOLATION (db) 5 1 1.2 1.4 1.6 1.8 2 -TO- ISOLATION ( = +1 dbm) 1 2 3 4 5 1 1.2 1.4 1.6 1.8 2 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q)..5 [12.7] 1. [25.4].25 [6.35] IR12LC1A, B and C IN 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IF OUT > IN < CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8] TERMINATE UNUSED IF OUTPUT.5 [12.7] OUTLINE DRAWINGS IR12LC1Q 25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35].5 [12.7] 1. [25.4].25 [6.35] IN 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IN I Q CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8].5 [12.7] 25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35] IMAGE REJECTION NOTE: All dimensions shown in brackets [ ] are in millimeters. QIFM, I/Q DEMODULATOR 172

FEATURES 1 TO 4 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IR14LC1A, IR14LC1B, IR14LC1C AND IR14LC1Q / coverage... 1 to 4 GHz IF operation... DC to.5 GHz Conversion loss... 8 db typical Image rejection... 2 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 1 4 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 1 4 power range IR14LC1 dbm +1 +12 +13 IR14MC1 dbm +13 +15 +16 IR14HC1 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 8 9.5 IR14LC1Q db 11 12.5 Single-sideband noise figure db 1 Image rejection (Note 1) < db 18 2 -to- isolation db 18 2 -to-if isolation db 2 Input power at 1 db compression IR14LC1 dbm +6 IR14MC1 dbm +1 IR14HC1 dbm +15 Input two-tone third-order intercept point IR14LC1 dbm +16 IR14MC1 dbm +2 IR14HC1 dbm +25 Amplitude balance IR14LC1Q db ±1.5 Phase balance IR14LC1Q Degrees ±12.5 Truth table IR14LC1Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IR14LC1A MHz 2 4 IR14LC1B MHz 4 8 IR14LC1C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IR14LC1Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 173

IRO14LC1C TYPICAL TEST DATA VSWR ( = +13 dbm) IMAGE REJECTION/CONVERSION SS ( = +13 dbm/if = 15MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 IMAGE REJECTION CONVERSION SS AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 1:1 1 1.6 2.2 2.8 3.4 4 3 1.5-1.5 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) -3 1 1.6 2.2 2.8 3.4 4 25 12.5-12.5-25 1 1.6 2.2 2.8 3.4 4 ISOLATION (db) 5 1 1.6 2.2 2.8 3.4 4 2 4 6 8 -TO- ISOLATION ( = +13 dbm) 1 1 1.6 2.2 2.8 3.4 4 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). OUTLINE DRAWINGS.5 [12.7] 1. [25.4].25 [6.35] IN IR14LC1A, B and C 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IF OUT > IN < CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8] TERMINATE UNUSED IF OUTPUT.5 [12.7] 25 [6.35] 1. [25.4].25 [6.35] FINISH: NICKEL 1.75 [6.35] IMAGE REJECTION NOTE: All dimensions shown in brackets [ ] are in millimeters..5 [12.7] 1. [25.4].25 [6.35] IN MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) IR14LC1Q 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA M/N XXXXXX S/N XXXXXX.75 [1.91] 2.35 [59.69] IN I Q CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8].5 [12.7] QIFM, I/Q DEMODULATOR 25 [6.35] 1. [25.4].25 [6.35] FINISH: NICKEL 1.75 [6.35] 174

2 TO 4 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IRM24LC2A, IRM24LC2B, IRM24LC2C AND IRM24LC2Q FEATURES / coverage... 2 to 4 GHz IF operation... DC to.5 GHz Conversion loss... 6 db typical Image rejection... 25 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 2 4 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 2 4 power range IRM24LC2 dbm +1 +12 +13 IRM24MC2 dbm +13 +15 +16 IRM24HC2 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 6 7.5 IRM24LC2Q db 9 1.5 Single-sideband noise figure db 8 Image rejection (Note 1) < db 18 25 -to- isolation db 2 3 -to-if isolation db 25 Input power at 1 db compression IRM24LC2 dbm +6 IRM24MC2 dbm +1 IRM24HC2 dbm +15 Input two-tone third-order intercept point IRM24LC2 dbm +16 IRM24MC2 dbm +2 IRM24HC2 dbm +25 Amplitude balance IRM24LC2Q db ±1.5 Phase balance IRM24LC2Q Degrees ±1 Truth table IRM24LC2Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IRM24LC2A MHz 2 4 IRM24LC2B MHz 4 8 IRM24LC2C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IRM24LC2Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 175

IRM24LC2A TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 3 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 VSWR VSWR IMAGE REJECTION (db) 1 2 3 4 CONVERSION SS IMAGE REJECTION CONVERSION SS (db) 1:1 5 2 2.4 2.8 3.2 3.6 4 2 2.4 2.8 3.2 3.6 4 AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 3 1.5-1.5-3 2 2.4 2.8 3.2 3.6 4 2 1-1 -2 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) 2 2.4 2.8 3.2 3.6 4 ISOLATION (db) 1 2 3 4 -TO- ISOLATION ( = +1 dbm) 5 2 2.4 2.8 3.2 3.6 4 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). GENERAL NOTES 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. 2. For upconverter applications, please order Model Number SSM24 Series. See Modulator section of catalog..5 [12.7].75 [1.91].5 [12.7].1 DIA. [2.54] MTG. HOLE (TYP. 2 PLACES) IRM24LC2A, B and C IN IN 1 Davids Drive IRO12A16B S/N XXXXXX NOTES: 1. TERM UNUSED IF PORT INTO 5 OHMS. 2. [5.8] 1.85 [46.99] IF OUT < > 2. FINISH: NICKEL.63 [1.6] IMAGE REJECTION.25 [6.35].375 [9.53] OUTLINE DRAWINGS.25 [6.35].75 [19.5] 1. [25.4] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES) NOTE: All dimensions shown in brackets [ ] are in millimeters..1 [2.54] DIA. MTG. HOLE (TYP. 2 PLACES) NOTE: 1. FINISH: NICKEL.75 [1.91].5 [12.7].5 [12.7] IN IN IRM24LC2Q 1 Davids Drive IRO12A16B S/N XXXXXX 2. [5.8] 1.85 [46.99] I Q.63 [1.6].375 [9.53] QIFM, I/Q DEMODULATOR.25 [6.35].25 [6.35] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES).75 [19.5] 1. [25.4] 176

2 TO 8 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IRM28LC2A, IRM28LC2B, IRM28LC2C AND IRM28LC2Q FEATURES / coverage... 2 to 8 GHz IF operation... DC to.5 GHz Conversion loss... 8.5 db typical Image rejection... 2 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 2 8 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 2 8 power range IRM28LC2 dbm +1 +12 +13 IRM28MC2 dbm +13 +15 +16 IRM28HC2 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 8.5 9 IRM28LC2Q db 11.5 12 Single-sideband noise figure db 9.5 Image rejection (Note 1) < db 18 2 -to- isolation db 18 2 -to-if isolation db 2 Input power at 1 db compression IRM28LC2 dbm +6 IRM28MC2 dbm +1 IRM28HC2 dbm +15 Input two-tone third-order intercept point IRM28LC2 dbm +16 IRM28MC2 dbm +2 IRM28HC2 dbm +25 Amplitude balance IRM28LC2Q db ±1.5 Phase balance IRM28LC2Q Degrees ±1 Truth table IRM28LC2Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IRM28LC2A MHz 2 4 IRM28LC2B MHz 4 8 IRM28LC2C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IRM28LC2Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 177

IRM28LC2A TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 3 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 IMAGE REJECTION CONVERSION SS CONVERSION SS (db) 1:1 2 3.2 4.4 5.6 6.8 8 5 2 3.2 4.4 5.6 6.8 8 AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 3 1.5 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) -1.5-3 2 3.2 4.4 5.6 6.8 8 2 1-1 -2 2 3.2 4.4 5.6 6.8 8 ISOLATION (db) 2 4 6 8 -TO- ISOLATION ( = +1 dbm) 1 2 3.2 4.4 5.6 6.8 8 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTES 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. 2. For upconverter applications, please order Model Number SSM28 Series. See Modulator section of catalog. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). OUTLINE DRAWINGS.5 [12.7].1 DIA. [2.54] MTG. HOLE (TYP. 2 PLACES).5 [12.7].75 [1.91] IRM28LC2A, B and C IN IN 1 Davids Drive IRO12A16B S/N XXXXXX NOTES: 1. TERM UNUSED IF PORT INTO 5 OHMS. 2. [5.8] 1.85 [46.99] IF OUT < >.63 [1.6] IMAGE REJECTION.25 [6.35].375 [9.53].25 [6.35].75 [19.5] 1. [25.4].1 [2.54] DIA. MTG. HOLE (TYP. 2 PLACES) TYPE SMA FEMALE CONNECTOR 2. FINISH: NICKEL (TYP. 4 PLACES) NOTE: 1. FINISH: NICKEL.75 [1.91].5 [12.7].5 [12.7] IN IN IRM28LC2Q 1 Davids Drive IRO12A16B S/N XXXXXX 2. [5.8] 1.85 [46.99] QIFM, I/Q DEMODULATOR I Q.63 [1.6].375 [9.53].25 [6.35].25 [6.35] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES).75 [19.5] 1. [25.4] NOTE: All dimensions shown in brackets [ ] are in millimeters. 178

MODELS: IRM48LC2A, IRM48LC2B, IRM48LC2C AND IRM48LC2Q FEATURES 4 TO 8 GHz IMAGE REJECTION OR I/Q MIXERS / coverage... 4 to 8 GHz IF operation... DC to.5 GHz Conversion loss... 7.5 db typical Image rejection... 23 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 4 8 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 4 8 power range IRM48LC2 dbm +1 +12 +13 IRM48MC2 dbm +13 +15 +16 IRM48HC2 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 7.5 8 IRM48LC2Q db 1.5 11 Single-sideband noise figure db 8.5 Image rejection (Note 1) < db 18 23 -to- isolation db 2 3 -to-if isolation db 25 Input power at 1 db compression IRM48LC2 dbm +6 IRM48MC2 dbm +1 IRM48HC2 dbm +15 Input two-tone third-order intercept point IRM48LC2 dbm +16 IRM48MC2 dbm +2 IRM48HC2 dbm +25 Amplitude balance IRM48LC2Q db ±1.5 Phase balance IRM48LC2Q Degrees ±1 Truth table IRM48LC2Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IRM48LC2A MHz 2 4 IRM48LC2B MHz 4 8 IRM48LC2C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IRM48LC2Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 179

IRM48LC2B TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS (IF = 6 MHz/ = +1 dbm) NOISE FIGURE (db) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 12.5 25 37.5 CONVERSION SS IMAGE REJECTION CONVERSION SS (db) 1:1 4 4.8 5.6 6.4 7.2 8 5 4 4.8 5.6 6.4 7.2 8 AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 3 1.5-1.5-3 2 1-1 -2 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) 4 4.8 5.6 6.4 7.2 8 4 4.8 5.6 6.4 7.2 8 ISOLATION (db) 2 4 6 8 -TO- ISOLATION ( = +1 dbm) 1 4 4.8 5.6 6.4 7.2 8 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTES 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. 2. For upconverter applications, please order Model Number SSM48 Series. See Modulator section of catalog. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q)..5 [12.7].75 [1.91].5 [12.7].1 DIA. [2.54] MTG. HOLE (TYP. 2 PLACES) IRM48LC2A, B and C IN IN 1 Davids Drive IRO12A16B S/N XXXXXX NOTES: 1. TERM UNUSED IF PORT INTO 5 OHMS. 2. [5.8] 1.85 [46.99] IF OUT < > 2. FINISH: NICKEL.63 [1.6] IMAGE REJECTION.25 [6.35].375 [9.53] OUTLINE DRAWINGS.25 [6.35].75 [19.5] 1. [25.4] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES) NOTE: All dimensions shown in brackets [ ] are in millimeters..1 [2.54] DIA. MTG. HOLE (TYP. 2 PLACES) NOTE: 1. FINISH: NICKEL.75 [1.91].5 [12.7].5 [12.7] IN IRM48LC2Q IN 1 Davids Drive IRO12A16B S/N XXXXXX 2. [5.8] 1.85 [46.99] I Q.63 [1.6].375 [9.53] QIFM, I/Q DEMODULATOR.25 [6.35].25 [6.35] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES).75 [19.5] 1. [25.4] 18

FEATURES 7.2 TO 8.4 GHz DIRECT SATELLITE I/Q DEMODULATOR Downlink... 7.2 to 7.7 GHz Uplink... 7.9 to 8.4 GHz MODEL: IR78LI3Q (TRI-BAND, X) Direct I/Q demodulation... DC to 25 MHz (5 ohms) Quadrature output accuracy... 35 db Linear dynamic range... 35 db (2.5 mv DC-offset voltage, 15 mv linear output voltage) High data rate I/Q modulated microwave signals are often demodulated by one direct conversion to baseband using a phase-locked oscillator. However, in order to preserve low BER the quadrature accuracy and signal-tonoise ratio (including residual DC offset voltage) must be high. Recently at MITEQ, the electrical and physical symmetry of our microwave mixer baluns and quadrature couplers have been improved to yield -to- isolation exceeding 45 db with very flat I/Q amplitude and phase response. These mixer qualities insure the low BER and also provide a low output VSWR interface for system baseband low-pass filters. This demodulator is an ideal complement to a similar construction I/Q linear modulator available from MITEQ. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 7.2 8.4 VSWR = +16 dbm Ratio 2:1 2.5:1 power at 1 db compression dbm +5 frequency range GHz 7.2 8.4 power range dbm +1 +13 VSWR Ratio 1.5:1 1.8:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (I or Q output) = dbm db 9.5 1.5 Maximum linear output voltage = +1 dbm, = +3 dbm mv 15 Maximum saturated output voltage = +1 dbm, = +1 dbm mv 4 Maximum DC offset voltage = +1 dbm, off mv 2.5 5 Quadrature phase accuracy Degrees 3 5 Quadrature amplitude accuracy db.5.75 -to- isolation db 25 3 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. I/Q frequency range.5 db bandwidth DC 25 I/Q VSWR (Ref. = 5 ohms) I/Q = 125 MHz Ratio 1.4:1 181

I Q IR78LI3Q TYPICAL TEST DATA 3.5:1 VSWR ( = +1 dbm, = + dbm) QUADRATURE ACCURACY ( = +1 dbm, = dbm) VSWR (RATIO) 3.:1 2.5:1 2.:1 1.5:1 ERROR LEVEL (db) -1-2 -3-4 1.:1 7.2 7.3 7.4 7.5 7.6 7.7-5 7.2 7.3 7.4 7.5 7.6 7.7 128 LINEAR DYNAMIC RANGE (RL = 5 Ω) 12.5 THEORETICAL QUADRATURE ACCURACY WITH VARIOUS PHASE-AMPLITUDE ERRORS OUTPUT VOLTAGE (mv) 32 = +3 dbm 8 = -3 dbm 2 5 DC OFFSET OFF 1.25 7.2 7.3 7.4 7.5 7.6 7.7 PHASE ERROR (db) 1 2 db 17 db 7.5 22 db 5 25 db 2.5 33 db.5 1 1.5 2 2.5 AMPLITUDE ERROR (db) MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C NOTE: Test data supplied at 25 C; conversion loss, phase and amplitude balance. OUTLINE DRAWING.75 [1.95].5 [12.7] 1. [25.4].85 [21.59].1 [2.54] DIA. MTG. HOLE (TYP. 2 PLACES).7 [17.78]].15 [3.81].5 [12.7] IN OUT M/N XXXXXX S/N XXXXXX.25 [6.35].75 [1.95].63 [1.62].375 [9.525].25 [6.35].75 [1.95].25 [6.35] FINISH: NICKEL NOTE: All dimensions shown in brackets [ ] are in millimeters. 182

MODELS: IRM812LC2A, IRM812LC2B, IRM812LC2C AND IRM812LC2Q FEATURES 8 TO 12 GHz IMAGE REJECTION OR I/Q MIXER / coverage... 8 to 12 GHz IF operation... DC to.5 GHz Conversion loss... 6.5 db typical Image rejection... 23 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 8 12 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 8 12 power range IRM812LC2 dbm +1 +12 +13 IRM812MC2 dbm +13 +15 +16 IRM812HC2 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 6.5 8 IRM812LC2Q db 9.5 11 Single-sideband noise figure db 8.5 Image rejection (Note 1) < db 18 23 -to- isolation db 2 3 -to-if isolation db 2 Input power at 1 db compression IRM812LC2 dbm +6 IRM812MC2 dbm +1 IRM812HC2 dbm +15 Input two-tone third-order intercept point IRM812LC2 dbm +16 IRM812MC2 dbm +2 IRM812HC2 dbm +25 Amplitude balance IRM812LC2Q db ±1 Phase balance IRM812LC2Q Degrees ±7.5 Truth table IRM812LC2Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IRM812LC2A MHz 2 4 IRM812LC2B MHz 4 8 IRM812LC2C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IRM812LC2Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 183

IRM812LC2B TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 6 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 CONVERSION SS IMAGE REJECTION CONVERSION SS (db) AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 1:1 8 8.8 9.6 1.4 11.2 12 2 1-1 -2 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) 8 8.8 9.6 1.4 11.2 12 16 8-8 -16 8 8.8 9.6 1.4 11.2 12 ISOLATION (db) 5 2 4 6 8 8 8.8 9.6 1.4 11.2 12 -TO- ISOLATION ( = +1 dbm) 1 8 8.8 9.6 1.4 11.2 12 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTES 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. 2. For upconverter applications, please order Model Number SSM812 Series. See Modulator section of catalog. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q)..5 [12.7].1 DIA. [2.54] MTG. HOLE (TYP. 2 PLACES).5 [12.7].75 [1.91] IRM812LC2A, B and C IN IN 1 Davids Drive IRO12A16B S/N XXXXXX NOTES: 1. TERM UNUSED IF PORT INTO 5 OHMS. 2. [5.8] 1.85 [46.99] IF OUT < >.63 [1.6].25 [6.35].375 [9.53] OUTLINE DRAWINGS.25 [6.35].75 [19.5] 1. [25.4].1 [2.54] DIA. MTG. HOLE (TYP. 2 PLACES) TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES) NOTE: 2. FINISH: NICKEL 1. FINISH: NICKEL IMAGE REJECTION.75 [1.91].5 [12.7].5 [12.7] IN IN IRM812LC2Q 1 Davids Drive IRO12A16B S/N XXXXXX 2. [5.8] 1.85 [46.99] I Q.63 [1.6].375 [9.53] QIFM, I/Q DEMODULATOR.25 [6.35].25 [6.35] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES).75 [19.5] 1. [25.4] NOTE: All dimensions shown in brackets [ ] are in millimeters. 184

FEATURES 1 TO 18 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IRM118LC1A, IRM118LC1B, IRM118LC1C AND IRM118LC1Q / coverage... 1 to 18 GHz IF operation... DC to.5 GHz Conversion loss... 1 db typical Image rejection... 2 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 1 18 VSWR ( = -1 dbm) Ratio 3:1 frequency range GHz 1 18 power range IRM118LC1 dbm +1 +12 +13 IRM118MC1 dbm +13 +15 +16 IRM118HC1 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 1 11 IRM118LC1Q db 13 14 Single-sideband noise figure db 11.5 Image rejection (Note 1) < db 15 2 -to- isolation db 18 2 -to-if isolation db 2 Input power at 1 db compression IRM118LC1 dbm +6 IRM118MC1 dbm +1 IRM118HC1 dbm +15 Input two-tone third-order intercept point IRM118LC1 dbm +16 IRM118MC1 dbm +2 IRM118HC1 dbm +25 Amplitude balance IRM118LC1Q db ±1.5 Phase balance IRM118LC1Q Degrees ±15 Truth table IRM118LC1Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IRM118LC1A MHz 2 4 IRM118LC1B MHz 4 8 IRM118LC1C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IRM118LC1Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 185

IRM118LC1B TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 6 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 CONVERSION SS IMAGE REJECTION CONVERSION SS (db) 1:1 4 8 12 16 2 4 8 12 16 2 AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 3 1.5-1.5-3 AMPLITUDE AND PHASE BALANCE (I,Q, = +1 dbm) 1 4.4 7.8 11.2 14.6 18 3 15-15 -3 1 4.4 7.8 11.2 14.6 18 ISOLATION (db) 2 4 6 8 -TO- ISOLATION ( = +1 dbm) 4 8 12 16 2 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). OUTLINE DRAWINGS.5 [12.7] 1. [25.4].25 [6.35] IRMO118LC1A, B and C TERM IN TERMINATION (5 OHMS) 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IF OUT > IN < CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8] TERMINATE UNUSED IF OUTPUT.5 [12.7].25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35].5 [12.7] 1. [25.4].25 [6.35] IN IRMO118LC1Q TERMINATION (5 OHMS) TERM 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IN I Q CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8].5 [12.7].25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35] IMAGE REJECTION NOTE: All dimensions shown in brackets [ ] are in millimeters. QIFM, I/Q DEMODULATOR 186

6 TO 18 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IRM618LC2A, IRM618LC2B, IRM618LC2C AND IRM618LC2Q FEATURES / coverage... 6 to 18 GHz IF operation... DC to.5 GHz Conversion loss... 9 db typical Image rejection... 2 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 6 18 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 6 18 power range IRM618LC2 dbm +1 +12 +13 IRM618MC2 dbm +13 +15 +16 IRM618HC2 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 9 1 IRM618LC2Q db 12 13 Single-sideband noise figure db 1.5 Image rejection (Note 1) < db 18 2 -to- isolation db 18 2 -to-if isolation db 2 Input power at 1 db compression IRM618LC2 dbm +6 IRM618MC2 dbm +1 IRM618HC2 dbm +15 Input two-tone third-order intercept point IRM618LC2 dbm +16 IRM618MC2 dbm +2 IRM618HC2 dbm +25 Amplitude balance IRM618LC2Q db ±1.5 Phase balance IRM618LC2Q Degrees ±15 Truth table IRM618LC2Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IRM618LC2A MHz 2 4 IRM618LC2B MHz 4 8 IRM618LC2C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IRM618LC2Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 187

IRM618LC2C TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 15 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 CONVERSION SS IMAGE REJECTION CONVERSION SS (db) 1:1 6 8.4 1.8 13.2 15.6 18 5 6 8.4 1.8 13.2 15.6 18 AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 3 1.5 3 15-15 -3 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) -1.5-3 6 8.4 1.8 13.2 15.6 18 6 8.4 1.8 13.2 15.6 18 ISOLATION (db) 2 4 6 8 -TO- ISOLATION ( = +1 dbm) 1 6 8.4 1.8 13.2 15.6 18 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). GENERAL NOTES 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. 2. For upconverter applications, please order Model Number SSM618 Series. See Modulator section of catalog..5 [12.7].75 [1.91].5 [12.7].1 DIA. [2.54] MTG. HOLE (TYP. 2 PLACES) IRM618LC2A, B and C IN IN 1 Davids Drive IRO12A16B S/N XXXXXX NOTES: 1. TERM UNUSED IF PORT INTO 5 OHMS. 2. [5.8] 1.85 [46.99] IF OUT < > 2. FINISH: NICKEL.63 [1.6] IMAGE REJECTION OUTLINE DRAWINGS.25 [6.35].375 [9.53].25 [6.35].75 [19.5] 1. [25.4] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES) NOTE: All dimensions shown in brackets [ ] are in millimeters. IN IN.1 [2.54] DIA. MTG. HOLE (TYP. 2 PLACES) NOTES: FINISH: NICKEL.75 [1.91].5 [12.7].5 [12.7] IRM618LC2Q IN IN 1 Davids Drive IRO12A16B S/N XXXXXX 2. [5.8] 1.85 [46.99] I Q.63 [1.6] QIFM, I/Q DEMODULATOR I Q.375 [9.53].25 [6.35].25 [6.35] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES).75 [19.5] 1. [25.4] 188

FEATURES 2 TO 18 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IRM218LC1A, IRM218LC1B, IRM218LC1C AND IRM218LC1Q / coverage... 2 to 18 GHz IF operation... DC to.5 GHz Conversion loss... 8 db typical Image rejection... 2 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 2 18 VSWR ( = -1 dbm) Ratio 3:1 frequency range GHz 2 18 power range IRM218LC1 dbm +1 +12 +13 IRM218MC1 dbm +13 +15 +16 IRM218HC1 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 8 11 IRM218LC1Q db 11 14 Single-sideband noise figure db 8.5 Image rejection (Note 1) < db 18 2 -to- isolation db 18 2 -to-if isolation db 2 Input power at 1 db compression IRM218LC1 dbm +6 IRM218MC1 dbm +1 IRM218HC1 dbm +15 Input two-tone third-order intercept point IRM218LC1 dbm +16 IRM218MC1 dbm +2 IRM218HC1 dbm +25 Amplitude balance IRM218LC1Q db ±1.5 Phase balance IRM218LC1Q Degrees ±15 Truth table IRM218LC1Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IRM218LC1A MHz 2 4 IRM218LC1B MHz 4 8 IRM218LC1C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IRM218LC1Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 189

IRM218LC1B TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 6 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 CONVERSION SS IMAGE REJECTION CONVERSION SS (db) 1:1 4 8 12 16 2 4 8 12 16 2 AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 3 1.5-1.5-3 AMPLITUDE AND PHASE BALANCE (I,Q, = +1 dbm) 1 4.4 7.8 11.2 14.6 18 3 15-15 -3 1 4.4 7.8 11.2 14.6 18 ISOLATION (db) 2 4 6 8 -TO- ISOLATION ( = +1 dbm) 4 8 12 16 2 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). OUTLINE DRAWINGS GENERAL NOTES 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. 2. For upconverter applications, please order Model Number SSM218 Series. See Modulator section of catalog..5 [12.7] 1. [25.4].25 [6.35] IRM218LC1A, B and C TERM IN TERMINATION (5 OHMS) 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IF OUT > IN < CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8] TERMINATE UNUSED IF OUTPUT.5 [12.7].25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35].5 [12.7] 1. [25.4].25 [6.35] IN IRM218LC1Q TERMINATION (5 OHMS) TERM 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IN I Q CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8].5 [12.7].25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35] IMAGE REJECTION NOTE: All dimensions shown in brackets [ ] are in millimeters. QIFM, I/Q DEMODULATOR 19

MODELS: IRM1218LC2A, IRM1218LC2B, IRM1218LC2C AND IRM1218LC2Q FEATURES 12 TO 18 GHz IMAGE REJECTION OR I/Q MIXERS / coverage... 12 to 18 GHz IF operation... DC to.5 GHz Conversion loss... 8 db typical Image rejection... 2 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 12 18 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 12 18 power range IRM1218LC2 dbm +1 +12 +13 IRM1218MC2 dbm +13 +15 +16 IRM1218HC2 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 8 1 IRM1218LC2Q db 11 13 Single-sideband noise figure db 1 Image rejection (Note 1) < db 18 2 -to- isolation db 2 23 -to-if isolation db 2 Input power at 1 db compression IRM1218LC2 dbm +6 IRM1218MC2 dbm +1 IRM1218HC2 dbm +15 Input two-tone third-order intercept point IRM1218LC2 dbm +16 IRM1218MC2 dbm +2 IRM1218HC2 dbm +25 Amplitude balance IRM1218LC2Q db ±1.5 Phase balance IRM1218LC2Q Degrees ±15 Truth table IRM1218LC2Q PORT < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IRM1218LC2A MHz 2 4 IRM1218LC2B MHz 4 8 IRM1218LC2C MHz 1 2 IF frequency (QIFM, I/Q demodulator) IRM1218LC2Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 191

IRM1218LC2A TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 3 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 CONVERSION SS IMAGE REJECTION CONVERSION SS (db) 1:1 5 12 13.2 14.4 15.6 16.8 18 12 13.2 14.4 15.6 16.8 18 AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 3 1.5-1.5-3 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) 12 13.2 14.4 15.6 16.8 18 3 15-15 -3 12 13.2 14.4 15.6 16.8 18 2 4 6 8 -TO- ISOLATION ( = +1 dbm) 1 12 13.2 14.4 15.6 16.8 18 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). OUTLINE DRAWINGS GENERAL NOTES 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. 2. For upconverter applications, please order Model Number SSM1218 Series. See Modulator section of catalog..5 [12.7].75 [1.91].5 [12.7].1 DIA. [2.54] MTG. HOLE (TYP. 2 PLACES) IRM1218LC2A, B and C IN IN 1 Davids Drive IRO12A16B S/N XXXXXX NOTES: 1. TERM UNUSED IF PORT INTO 5 OHMS. 2. [5.8] 1.85 [46.99] IF OUT < > 2. FINISH: NICKEL.63 [1.6] IMAGE REJECTION.25 [6.35].375 [9.53].25 [6.35].75 [19.5] 1. [25.4] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES).1 [2.54] DIA. MTG. HOLE (TYP. 2 PLACES) NOTE: 1. FINISH: NICKEL.75 [1.91].5 [12.7].5 [12.7] IRM1218LC2Q IN IN 1 Davids Drive IRO12A16B S/N XXXXXX 2. [5.8] 1.85 [46.99] I Q.63 [1.6].375 [9.53] QIFM, I/Q DEMODULATOR.25 [6.35].25 [6.35] TYPE SMA FEMALE CONNECTOR (TYP. 4 PLACES).75 [19.5] 1. [25.4] NOTE: All dimensions shown in brackets [ ] are in millimeters. 192

MODELS: IRM226LC1A, IRM226LC1B, IRM226LC1C AND IRM226LC1Q FEATURES 2 TO 26 GHz IMAGE REJECTION OR I/Q MIXERS / coverage... 2 to 26 GHz IF operation... DC to.5 GHz Conversion loss... 1 db typical Image rejection... 18 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 2 26 VSWR ( = -1 dbm) Ratio 3.5:1 frequency range GHz 2 26 power range IRM226LC1 dbm +1 +12 +13 IRM226MC1 dbm +13 +15 +16 IRM226HC1 dbm +17 +18 +2 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > dbm 1 14.5 IRM226LC1Q db 13 17.5 Single-sideband noise figure db 15 Image rejection (Note 1) < db 15 18 -to- isolation db 15 18 -to-if isolation db 2 Input power at 1 db compression IRM226LC1 dbm +6 IRM226MC1 dbm +1 IRM226HC1 dbm +15 Input two-tone third-order intercept point IRM226LC1 dbm +16 IRM226MC1 dbm +2 IRM226HC1 dbm +25 Amplitude balance IRM226LC1Q db ±1.5 Phase balance IRM226LC1Q Degrees ±15 Truth table IRM226LC1Q Port < > I -9 Q -9 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IRM226LC1A MHz 2 4 IRM226LC1B MHz 4 8 IRM226LC1C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IRM226LC1Q MHz DC 5 IF VSWR (IF = -1 dbm) Ratio 1.5:1 193

IRM226LC1C TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION/CONVERSION SS ( = +1 dbm/if = 15 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 CONVERSION SS IMAGE REJECTION CONVERSION SS (db) AMPLITUDE BALANCE (db) PHASE BALANCE (DEG.) 1:1 2 6.8 11.6 16.4 21.2 26 3 1.5-1.5-3 2 6.8 11.6 16.4 21.2 26 3 15-15 -3 AMPLITUDE AND PHASE BALANCE (I/Q, = +1 dbm) 2 6.8 11.6 16.4 21.2 26 ISOLATION (db) 5 1 2 3 4 5 2 6.8 11.6 16.4 21.2 26 -TO- ISOLATION ( = +1 dbm) 2 6.8 11.6 16.4 21.2 26 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTES 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. 2. For upconverter applications, please order Model Number SSM226 Series. See Modulator section of catalog. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). OUTLINE DRAWINGS.5 [12.7] 1. [25.4].25 [6.35] IRMO226LC1A, B and C TERM IN TERMINATION (5 OHMS) 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IF OUT > IN < CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8] TERMINATE UNUSED IF OUTPUT.5 [12.7].25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35].5 [12.7] 1. [25.4].25 [6.35] IN IRMO226LC1Q TERMINATION (5 OHMS) TERM 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA.75 [1.91] 2.35 [59.69] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES) M/N XXXXXX S/N XXXXXX IN I Q CONNECTORS SMA FEMALE (TYP. 4 PLACES) 2. [5.8].5 [12.7].25 [6.35].25 [6.35] 1. [25.4] FINISH: NICKEL 1.75 [6.35] IMAGE REJECTION NOTE: All dimensions shown in brackets [ ] are in millimeters. QIFM, I/Q DEMODULATOR 194

18 TO 26 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IR1826NI7A, IR1826NI7B, IR1826NI7C AND IR1826NI7Q FEATURES / coverage... 18 to 26 GHz IF operation... DC to.5 GHz power range... +17 to +19 dbm Conversion loss... 9 db typical Image rejection... 25 db typical IR1826NI7Q MITEQ s IR Series of image rejection mixers is useful for wideband test equipment or in ultra-broadband receivers requiring rejection of an unwanted sideband of signal or noise following a low-noise front-end amplifier. These mixers are also useful as linear single-sideband upconverters by operating in the reverse mode. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 18 26 VSWR ( = -1 dbm, = +17 dbm) Ratio 2:1 frequency range GHz 18 26 power range dbm +17 +19 VSWR ( = +17 dbm) Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > db 9 1.5 IR1826NI7Q db 12 13.5 Single-sideband noise figure db 9.5 Image rejection (Note 1) < db 18 25 -to- isolation db 2 25 -to-if isolation db 15 Input power at 1 db compression = +17 dbm dbm +7 Input two-tone third-order intercept point = +17 dbm dbm +17 Amplitude balance IR1826NI7Q db ±1 ±1.5 Phase balance IR1826NI7Q Degrees ±1 ±15 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IR1826NI7A MHz 2 4 IR1826NI7B MHz 4 8 IR1826NI7C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IR1826NI7Q MHz DC 5 IF VSWR (IF = -1 dbm, = +17 dbm) Ratio 1.5:1 195

IR1826NI7C TYPICAL TEST DATA VSWR ( = +17 dbm) IMAGE REJECTION ( = +17 dbm, IF = 15 MHz) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 1:1 5 18 19.6 21.2 22.8 24.4 26 18 19.6 22.8 21.2 24.4 26 CONVERSION SS (IF = 15 MHz, = +17 dbm) -TO- ISOLATION ( = +17 dbm) CONVERSION SS (db) 4 8 12 16 ISOLATION (db) 2 4 6 8 2 1 18 19.6 21.2 22.8 24.4 26 18 19.6 22.8 21.2 24.4 26 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). SMA OR K FEMALE.75 [19.5] IR1826NI7A, B and C.685 [17.399] IF.325 [8.255] TYP. (2 PLACES) SMA OR K FEMALE.312 [7.925] TYP. (2 PLACES).375 [9.525] TYP. (2 PLACES).483 [12.268] IF SMA FEMALE.375 [9.525].82 [2.83].667 [16.942].82 [2.83].12 [2.591] FINISH: IRRIDITE OUTLINE DRAWINGS.583 [14.88] 2-56.125 [3.175] DEEP MIN. TYP. (2 PLACES).585 [14.859].12 [2.591] FINISH: GOLD.16 [4.64].26.163 [4.14].357.52 [6.6] [9.68] [13.28] TYPE 2.9 MM FIELD REPLACEABLE FEMALE CONNECTOR (TYP. 2 PLACES).29 [7.366].195 [4.953].55 [1.397].45 [11.43] IR1826NI7Q IF 1 4X.38 [9.652].28 [7.112].56 [14.224].24 [6.96].39 [9.96].42 [1.67].436 [11.74] 2X #-8 X.1 [2.54] DP.67 [1.72] DIA. THRU MOUNTING HOLES (4 PLACES) IF 2 TYPE SMA FIELD REPLACEABLE FEMALE CONNECTOR (2 PLACES).1 [2.54] OPTIONAL SPACER PLATE IMAGE REJECTION NOTE: All dimensions shown in brackets [ ] are in millimeters. QIFM, I/Q DEMODULATOR 196

26 TO 4 GHz IMAGE REJECTION OR I/Q MIXERS MODELS: IR264NI7A, IR264NI7B, IR264NI7C AND IR264NI7Q FEATURES / coverage... 26 to 4 GHz IF operation... DC to.5 GHz power range... +17 to +18 dbm Conversion loss... 9 db typical Image rejection... 25 db typical IR264NI7Q MITEQ s IR Series of image rejection mixers is useful for wideband test equipment or in ultra-broadband receivers requiring rejection of an unwanted sideband of signal or noise following a low-noise front-end amplifier. These mixers are also useful as linear single-sideband upconverters by operating in the reverse mode. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 26 4 VSWR ( = -1 dbm, = +16 dbm) Ratio 2:1 frequency range GHz 26 4 power range dbm +17 +18 VSWR ( = +16 dbm) Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) > db 9 12 IR264NI7Q db 12 15 Single-sideband noise figure db 9.5 Image rejection (Note 1) < db 18 25 -to- isolation db 2 25 -to-if isolation db 25 Input power at 1 db compression = +16 dbm dbm +7 Input two-tone third-order intercept point = +16 dbm dbm +17 Amplitude balance IR264NI7Q db ±1 ±1.5 Phase balance IR264NI7Q Degrees ±1 ±15 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency (image rejection mode) IR264NI7A MHz 2 4 IR264NI7B MHz 4 8 IR264NI7C MHz 1 2 IF frequency (QIFM, I/Q demodulator mode) IR264NI7Q MHz DC 5 IF VSWR (IF = -1 dbm, = +16 dbm) Ratio 1.5:1 1 Davids Drive, Hauppauge, NY 11788 TEL: (631) 439-922 FAX: (631) 436-743 www.miteq.com Revised: 3/19/13

IR264NI7C TYPICAL TEST DATA CONVERSION GAIN (db) CONVERSION GAIN, > (LSB REJECTED = +16 dbm, = -1 dbm, IF = 15 MHz) -6-8 -1-12 -14 26 28 3 32 34 36 38 4 IMAGE REJECTION, IMAGE < (LSB REJECTED = +16 dbm, = -1 dbm, IF = 15 MHz) 4 ISOLATION (db) -1-15 -2-25 -3-25 -4-45 -5-55 -TO- AND -TO-IF ISOLATION ( = +16 dbm) -6 26 28 3 32 34 36 38 4 3.5:1 -TO- -TO-IF AND PORT VSWR ( = +16 dbm) IMAGE REJECTION (db) 35 3 25 2 15 VSWR (RATIO) 3.:1 2.5:1 2.:1 1.5:1 1 1.:1 26 28 3 32 34 36 38 4 26 28 3 32 34 36 38 4 IMAGE MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation, image rejection (IF Options A, B and C), phase and amplitude balance (IF Option Q). OUTLINE DRAWINGS SMA OR K FEMALE.75 [19.5] IR264NI7A, B and C.685 [17.399] IF.325 [8.255] TYP. (2 PLACES) SMA OR K FEMALE.312 [7.925] TYP. (2 PLACES).375 [9.525] TYP. (2 PLACES).483 [12.268] FINISH: IRRIDITE IF 1 IF SMA FEMALE.583.16 [4.64] [14.88].375 [9.525].26.163 [4.14] 2-56.125 [3.175].357 [6.6].82 [2.83] DEEP MIN. TYP..52 [9.68] (2 PLACES) [13.28].667 [16.942].82 [2.83].12 [2.591] FINISH: IRRIDITE IMAGE REJECTION.585 [14.859].12 [2.591] NOTE: All dimensions shown in brackets [ ] are in millimeters. TYPE 2.9 MM FIELD REPLACEABLE FEMALE CONNECTOR (TYP. 2 PLACES).29 [7.366].195 [4.953] IR264NI7Q.55 [1.397].45 [11.43] 4X.38 [9.652].28 [7.112].56 [14.224].24 [6.96] QIFM, I/Q DEMODULATOR.39 [9.96].42 [1.67].436 [11.74] 2X #-8 X.1 [2.54] DP.67 [1.72] DIA. THRU MOUNTING HOLES (4 PLACES) IF 2 TYPE SMA FIELD REPLACEABLE FEMALE CONNECTOR (2 PLACES).1 [2.54] OPTIONAL SPACER PLATE 198

MODELS: IRJ8595U3A, IRJ8595U6A, IRJ8595U12A AND IRJ8595U15A FEATURES 8.5 TO 9.5 GHz IMAGE REJECTION DOWNCONVERTER coverage... 8.5 to 9.5 GHz coverage... 8.38 to 9.38 GHz IF operation... 2 to 2 MHz Conversion loss... 7 db typical Image rejection... 25 db typical ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 8.5 9.5 VSWR Ratio 2:1 frequency range GHz 8.38 9.38 power range dbm 7 9 VSWR Ratio 2:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss @ Mid-band IF db 7 8 Image rejection @ Mid-band IF db 18 25 -to- isolation db 3 35 -to-if isolation db 25 Output power at 1 db compression dbm -6 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency range IRJ8595U3A MHz 2 4 IRJ8595U6A MHz 4 6 IRJ8595U12A MHz 8 16 IRJ8595U15A MHz 1 2 IF VSWR (IF = -1 dbm) Ratio 1.5:1 199

IRJ8595U12A TYPICAL TEST DATA CONVERSION GAIN (db) -2-4 -6-8 CONVERSION GAIN - UPPER SIDEBAND (LSB REJECTED = +7 dbm = -5 dbm IF= 12 MHz) MIN. -1 85 86 87 88 89 9 91 92 93 94 95 FREQUENCY (MHz) IMAGE REJECTION (db) IMAGE REJECTION 5 45 4 35 3 25 2 MIN. 15 1 83 84 85 86 87 88 89 9 91 92 IMAGE FREQUENCY (MHz) 5 -TO- ISOLATION (LSB REJECTED = +7 dbm = -5 dbm IF= 12 MHz) -TO- ISOLATION (db) 45 4 35 3 25 MIN. MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -55 to +85 C Storage temperature... -65 to +95 C 2 84 85 86 87 88 89 9 91 92 93 FREQUENCY (MHz) NOTE: Test data supplied at 25 C; conversion loss, -to- isolation and image rejection. OUTLINE DRAWING.5 [12.7].8 [2.3].8 [2.3].82 [2.83].66 [16.76].33 [8.38] 1.16 [29.46].84 [21.34] 1. [25.4] IF PORT IF PORT.16 [4.6] (TYP. 3 PLACES) TYPE 'SMA' FEMALE CONNECTOR (TYP. 3 PLACES).38 [9.65] TYP..41 [1.41] PORT.1 [2.54] DIA. MOUNTING HOLES (TYP. 2 PLACES) FINISH: NICKEL NOTE: All dimensions shown in brackets [ ] are in millimeters. 2

8.5 TO 9.5 GHz IMAGE REJECTION UPCONVERTER MODEL: IRJ8595L12A FEATURES coverage... 8.5 to 9.5 GHz coverage... 8.38 to 9.38 GHz IF operation... 8 to 16 MHz ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency range MHz 8 12 16 IF inpedance Ohms 5 frequency range GHz 8.38 9.38 power range dbm 7 9 impedance Ohms 5 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss @ 12 MHz IF db 7 8 Image rejection @ 12 MHz IF db 18 25 -to- isolation db 3 35 -to-if isolation db 25 Output power at 1 db compression dbm -6 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range MHz 8.5 9.5 impedance Ohms 5 21

IRJ8595L12A TYPICAL TEST DATA FREQUENCY + 1 IF 1 IF (MHz) (db) (db) (dbc) 838. -37.9-6.4-27.3 858. -36.8-6.8-28.3 878. -37.5-6.7-25.5 898. -35.7-6.7-23. 918. -34.3-7.5-23.3 938. -34.3-7.1-22.8 NOTE: Units measured at an IF frequency of 12 MHz and at 25 C. MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -55 to +85 C Storage temperature... -65 to +95 C NOTE: Test data supplied at 25 C; conversion loss, -to- isolation and image rejection. OUTLINE DRAWING.5 [12.7].8 [2.3].8 [2.3] 1.16 [29.46].84 [21.34] 1. [25.4] IF PORT.16 [4.6] (TYP. 3 PLACES) TYPE 'SMA' FEMALE CONNECTOR (TYP. 3 PLACES).38 [9.65] TYP..82 [2.83].66 [16.76].33 [8.38] IF PORT NOTE: All dimensions shown in brackets [ ] are in millimeters..41 [1.41] PORT.1 [2.54] DIA. MOUNTING HOLES (TYP. 2 PLACES) FINISH: NICKEL 22

2 TO 8 GHz ENHANCED IMAGE REJECTION MIXERS MODELS: IRE28LI1A, IRE28LI1B AND IRE28LI1C FEATURES / coverage... 2 to 8 GHz Conversion loss... 9 db typical Image rejection... 3 db typical Packaging... Hermetically sealed MITEQ s Model IRE28LI1 enhanced image rejection mixer utilizes a unique architecture developed to provide greater than 3 db of image rejection across multioctave bands. This design inherently suppresses image frequencies by an additional 15 db over conventional image rejection mixers without the need for phase and amplitude alignment during production test, allowing for consistent reliable performance throughout production. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 2 8 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 2 8 power range IRE28LI1 dbm +13 +15 +16 IRE28HI1 dbm +2 +22 +23 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) db 9 9.5 Single-sideband noise figure db 1 Image rejection (Note 1) db 25 3 -to- isolation db 24 3 Input power at 1 db compression IRE28LI1 dbm +8 IRE28HI1 dbm +15 Input two-tone third-order intercept point IRE28LI1 dbm +18 IRE28HI1 dbm +25 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency range IRE28LI1A MHz 2 4 IRE28LI1B MHz 4 8 IRE28LI1C MHz 1 2 IF VSWR (IF = -1 dbm) Ratio 1.5:1 23

IRE28LI1C TYPICAL TEST DATA VSWR ( = +14 dbm) IMAGE REJECTION ( = +14 dbm) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 1:1 2 3.2 4.4 5.6 6.8 8 5 2 3.2 4.4 5.6 6.8 8 CONVERSION SS (IF = 15 MHz, = +14 dbm) -TO- ISOLATION ( = +14 dbm) CONVERSION SS (db) 1 2 3 4 5 2 3.2 4.4 5.6 6.8 8 ISOLATION (db) 2 4 6 8 1 2 3.2 4.4 5.6 6.8 8 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Unit normally aligned for operation with >. If < is desired, please specify at time of order. Operation at both modes is a special option with some degradation in performance. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation and image rejection. OUTLINE DRAWING 1.5 [38.1] 2. [5.8] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES).5 [12.7].5 [12.7].75 [1.91] IN 2.5 [63.5] 2.35 [59.69].15 [3.81] 2.2 [55.88] IF OUT < IN > TERM UNUSED PORT.63 [1.6] CONNECTOR SMA FEMALE (TYP. 4 PLACES).375 [9.53].25 [6.35].25 [6.35] 1.25 [31.75] 1.75 [44.45] FINISH: NICKEL NOTE: All dimensions shown in brackets [ ] are in millimeters. 24

6 TO 18 GHz ENHANCED IMAGE REJECTION MIXERS MODELS: IRE618LI1A, IRE618LI1B AND IRE618LI1C FEATURES / coverage... 6 to 18 GHz power range... +13 to +15 dbm Conversion loss... 8 db typical Image rejection... 35 db typical Packaging... Hermetically sealed MITEQ s Model IRE618LI1 enhanced image rejection mixer utilizes a unique architecture developed to provide greater than 3 db of image rejection across multioctave bands. This design inherently suppresses image frequencies by an additional 15 db over conventional image rejection mixers without the need for phase and amplitude alignment during production test, thereby allowing for consistent reliable performance throughout production. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 6 18 VSWR ( = -1 dbm) Ratio 1.5:1 frequency range GHz 6 18 power range IRE618LI1 dbm +13 +15 +16 IRE618HI1 dbm +2 +22 +23 VSWR Ratio 2.5:1 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) db 8 1.5 Single-sideband noise figure db 8.5 Image rejection (Note 1) db 25 35 -to- isolation db 24 3 Input power at 1 db compression IRE618LI1 dbm +8 IRE618HI1 dbm +15 Input two-tone third-order intercept point IRE618LI1 dbm +18 IRE618HI1 dbm +25 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency range (image rejection mode) IRE618LI1A MHz 2 4 IRE618LI1B MHz 4 8 IRE618LI1C MHz 1 2 IF VSWR (IF = -1 dbm) Ratio 1.5:1 25

IRE618LI1B TYPICAL TEST DATA 6:1 VSWR ( = +14 dbm) IMAGE REJECTION ( = +14 dbm) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 1:1 6 8.4 1.8 13.2 15.6 18 5 6 8.4 1.8 13.2 15.6 18 CONVERSION SS (IF = 45 MHz, = +14 dbm) -TO- ISOLATION ( = +14 dbm) CONVERSION SS (db) 4 8 12 16 ISOLATION (db) 1 2 3 4 5 6 8.4 1.8 13.2 15.6 18 6 8.4 1.8 13.2 15.6 18 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C NOTE: Test data supplied at 25 C; conversion loss, -to- isolation and image rejection. OUTLINE DRAWING GENERAL NOTE 1. Unit normally aligned for operation with >. If < is desired, please specify at time of order. Operation at both modes is a special option with some degradation in performance. 1.5 [38.1] 2. [5.8] MOUNTING HOLES.1 [2.54] DIA. THRU (TYP. 4 PLACES).5 [12.7].5 [12.7].75 [1.91] IN 2.5 [63.5] 2.35 [59.69].15 [3.81] 2.2 [55.88] IF OUT < IN > TERM UNUSED PORT NOTE: All dimensions shown in brackets [ ] are in millimeters..63 [1.6] CONNECTOR SMA FEMALE (TYP. 4 PLACES).375 [9.53].25 [6.35].25 [6.35] 1.25 [31.75] 1.75 [44.45] FINISH: NICKEL 26

2 TO 18 GHz BIASABLE IMAGE REJECTION MIXERS MODELS: IRB218LC1A, IRB218LC1B AND IRB218LC1C FEATURES / coverage... 2 to 18 GHz IF operation... 2 to 2 MHz power range... -1 to +13 GHz Conversion loss... 1 db typical Image rejection... 2 db typical Image rejection mixers are useful for wideband test equipment or in ultra-broadband receivers requiring rejection of an unwanted sideband of signal or noise following a low-noise front-end amplifier. These mixers are also useful as linear single-sideband upconverters by operating in the reverse mode. The MITEQ IRB Series design utilizes two mixers with biasable bridge diode quads, thus allowing operation at very low powers. The bias circuit also automatically compensates for any power variations in the swept source. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 2 18 VSWR ( = -1 dbm, = dbm) Ratio 2:1 frequency range GHz 2 18 power range dbm -1 +13 VSWR ( = dbm) Ratio 2.5:1 DC power +15 VDC ma 25 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (Note 1) ( = -1 dbm, = dbm) > db 1 12.5 Single-sideband noise figure db 1 Image rejection (Note 1) < db 18 2 -to- isolation db 15 18 -to-if isolation db 2 Input power at 1 db compression = dbm dbm -1 Input two-tone third-order intercept point = dbm dbm OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency range IRB218LC1A MHz 2 4 IRB218LC1B MHz 4 8 IRB218LC1C MHz 1 2 IF VSWR (IF = -1 dbm, = dbm) Ratio 1.5:1 27

IRB218LC1A TYPICAL TEST DATA 6:1 VSWR ( = +3 dbm) IMAGE REJECTION ( = +1 dbm) VSWR (RATIO) 5:1 4:1 3:1 2:1 1:1 5 4 8 12 16 2 4 8 12 16 2 IMAGE REJECTION (db) 1 2 3 4 CONVERSION SS ( = -7 TO +13 dbm) (IF = 3 MHz) -TO- ISOLATION ( = +3 dbm) CONVERSION SS (db) 4 8 12 16 = +3 dbm = +13 dbm ISOLATION (db) 2 4 6 8 = +7 dbm 1 4 8 12 16 2 4 8 12 16 2 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion loss, -to- isolation and image rejection. OUTLINE DRAWING TERMINATION (5 OHMS) MOUNTING HOLES.1 [2.54] DIA. THRU TYP. 4 PLACES.5 [12.7] 1. [25.4].25 [6.35] 2.5 [63.5] > IN HAUPPAUGE, N.Y. 11788 MADE IN USA M/N XXXXXX S/N XXXXXX <.75 [1.91] 2.35 [59.69] IF OUT IN +VDC CONNECTORS SMA FEMALE (TYP. 3 PLACES).25 [6.35] 2. [5.8].5 [12.7].25 [6.35].24 [6.1].3 [.76] DIA. X.25 [6.35] LG. (TYP. 2 PLACES) 1. [25.4] 1.625 [41.28] 1.75 [44.45] FINISH: NICKEL NOTE: All dimensions shown in brackets [ ] are in millimeters. 28

I/Q PHASE DETECTOR WITH OPTIONAL VIDEO AMPS AND/OR DIGITAL OUTPUTS MODELS: IQM, IQD AND IQDD162 FEATURES / coverage... 15 to 17 MHz Center frequency... 16 MHz Phase accuracy... ±5 typical I/Q output voltage... ±2.5 volts (IQD Model) Variable offset and gain adjust Internal ±5 volt regulators Optional 8 BIT TTL output (IQDD Model) The IQM, IQD, and IQDD model I/Q phase detectors all utilize high isolation mixers and hybrids to minimize residual AC and DC circuit errors that limit phase accuracy. 1 MHz bandwidth video amplifiers are available (IQD model) to buffer outputs leading to the user s post circuitry or optional MITEQ A/D converters (IQDD model). IQM and IQD models require +13 dbm reference power and -2 to +1 dbm power for DC outputs. For AC video outputs, the lowest input power is limited by noise. The angular accuracy of the IQM and IQD models is measured at the maximum reference power. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. / frequency range (information B/W) MHz 15 17 phase accuracy bandwidth MHz 4 1 VSWR ( = +1 dbm, = +13 dbm) Ratio 1.5:1 power range dbm 1 13 VSWR ( = +13 dbm) Ratio 1.7:1 Current IQD -15/+15 ma -1/+1 IQDD -15/+15 ma -1/+5 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion loss (IQM model) db 8 1 Conversion gain, K (IQD model) Volt=KV RMS COS Ø K ratio 3.5 Equivalent image rejection (see reverse side) IF = 1 MHz db 22 25 Linear phase accuracy tan -1 V Q /V I = 13, = +3 Degrees 5 7 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IQM Output voltage ( = +1 dbm) mv 4 DC offset ( = +13 dbm, off) 5 ohm reference mv 2 5 VSWR ( = +13 dbm) Ratio 1.5:1 IQD Output voltage ( = +1 dbm) Volts 2.5 DC offset ( = +13 dbm, off) mv 3 VSWR ( = +13 dbm) -9 ohm reference Ratio 1.5:1 IQDD TTL 8-BIT clock rate required MHz 2 29

IQ SERIES REFERENCE DATA TEST SETUP FOR EQUIVALENT IMAGE REJECTION (FOR NON-DC VIDEO) 12.5 EQUIVALENT IMAGE REJECTION WITH VARIOUS PHASE-AMPLITUDE ERRORS IN +1 +13 IQD 162 - = 1 MHz 9 TEST SIGNALS FOR MEASURING I/Q PHASE LINEARITY (FOR DC VIDEO) 3 db FREQ. TO PHASE ENCODING CABLE LENGTH +3 dbm +13 dbm tan -1 V Q /V I PHASE ERROR (db) 1 2 db 17 db 7.5 22 db 5 2.5 25 db 33 db.5 1 1.5 2 2.5 AMPLITUDE ERROR (db) -1 VQ TAN VI VERSUS FREQUENCY AND TYPICAL PHASE LINEARITY ERROR OF IQD162C4 25 15 LINEARITY ERROR 5-5 tan -15-1 V O /V I -25-1 135 145 155 165 175 185 FREQUENCY (MHz) 1 6 2-2 -6 PHASE LINEARITY ERROR MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -3 to +7 C Storage temperature... -55 to +125 C GENERAL NOTES 1. Application and test, question and answer sheet are available from MITEQ. 2. limiter models available with -6 to dbm input dynamic range. OUTLINE DRAWING BCK DIAGRAM.75 [1.95] C4 HOUSING (Nonhermetic) 2.5 [63.5] 2.35 [59.69].25 [6.35].5 [12.7].75 [19.5].75 [19.5] 1.5 [38.1] 2. [5.8] H.1 [2.54] DIA. MTG. HOLE (TYP. 4 PLACES).25 [6.35] 1.25 [31.75] CONNECTORS SMA FEMALE (TYP. 4 PLACES) FINISH: NICKEL.463 [11.76].362 [9.195] 1.75 [44.45].25 [6.35] TYP. MODEL DIM. H IQM.5 IQD 1. IQDD 1.5 +15 V -15 V OFFSET IQDD LPF LPF OFFSET GAIN A-D A-D GAIN I VIDEO D D1 D2 D3 D4 D5 D6 D7 CCK D D1 D2 D3 D4 D5 D6 D7 Q VIDEO NOTE: All dimensions shown in brackets [ ] are in millimeters. +15 V -15 V 21

2 TO 26 GHz IMAGE REJECTION MIXERS MODELS: IRBA226LC1A, IRBA226LC1B AND IRBA226LC1C FEATURES / coverage... 2 to 26 GHz IF operation... 2 to 2 MHz power range... -1 to +13 dbm Conversion gain... 2 db typical Image rejection... 2 db typical Biasable Image rejection mixers are useful for wideband test equipment or ultra-broadband receivers requiring rejection of an unwanted sideband of signal or noise following a low-noise front-end amplifier. These mixers are also useful as linear single-sideband upconverters by operating in the reverse mode. The MITEQ IRBA Series design utilizes two mixers with biasable bridge diode quads, thus allowing operation at very low powers. An integrated IF amplifier also makes the unit s sensitivity less dependent on load noise and mismatch. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 2 26 VSWR ( = -3 dbm, = dbm) Ratio 2:1 frequency range GHz 2 26 power range dbm -1 +13 VSWR ( = dbm) Ratio 2.5:1 DC power +15 VDC ma 75 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion gain (Note 1) ( = -3 dbm, = dbm) > db 15 2 Single-sideband noise figure db 16 Image rejection (Note 1) ( = -3 dbm, = dbm) < db 15 2 -to- isolation db 2 25 -to-if isolation db 2 Output power at 1 db compression = dbm dbm +5 Output two-tone third-order intercept point = dbm dbm +15 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency range IRBA226LC1A MHz 2 4 IRBA226LC1B MHz 4 8 IRBA226LC1C MHz 1 2 IF VSWR (IF = -3 dbm, = dbm) Ratio 1.5:1 211

IRBA226LC1A TYPICAL TEST DATA VSWR ( = dbm) IMAGE REJECTION ( = dbm) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 1:1 2 6.8 11.6 16.4 21.2 26 2 6.8 11.6 16.4 21.2 26 5 CONVERSION GAIN (IF = 3 MHz, = dbm) -TO- ISOLATION ( = dbm) CONVERSION GAIN (db) 4 3 2 1 ISOLATION (db) 1 2 3 4 2 6.8 11.6 16.4 21.2 26 5 2 6.8 11.6 16.4 21.2 26 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion gain, -to- isolation and image rejection. OUTLINE DRAWING TERMINATION (5 OHMS) MOUNTING HOLES.1 [2.54] DIA. THRU TYP. 4 PLACES.5 [12.7] 1. [25.4].25 [6.35] 2.5 [63.5] > IN HAUPPAUGE, N.Y. 11788 MADE IN USA M/N XXXXXX S/N XXXXXX <.75 [1.91] 2.35 [59.69] IF OUT IN +VDC CONNECTORS SMA FEMALE (TYP. 3 PLACES).25 [6.35] 2. [5.8].5 [12.7].25 [6.35].24 [6.1].3 [.76] DIA. X.25 [6.35] LG. (TYP. 2 PLACES) 1. [25.4] 1.625 [41.28] 1.75 [44.45] FINISH: NICKEL NOTE: All dimensions shown in brackets [ ] are in millimeters. 212

2 TO 26 GHz IMAGE REJECTION MIXERS/IF AMP INPUT MODELS: IRA226LC1A, IRA226LC1B AND IRA226LC1C FEATURES / coverage... 2 to 26 GHz IF operation... 2 to 2 MHz power range... +1 to +13 dbm Conversion gain... 23 db typical Image rejection... 2 db typical Image rejection mixers are useful for wideband test equipment or ultra-broadband receivers requiring rejection of an unwanted sideband of signal or noise following a low-noise front-end amplifier. The IRA Series of image rejection mixers has an integrated IF amplifier, thus making the overall sensitivity less dependent on the load noise. The mixer/if interface is also optimized for best 2-2 spur performance. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 2 26 VSWR ( = -3 dbm, = +12 dbm) Ratio 2:1 frequency range GHz 2 26 power range dbm +1 +12 +13 VSWR ( = +12 dbm) Ratio 2.5:1 DC power +15 VDC ma 75 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion gain (Note 1) > db 2 23 Single-sideband noise figure db 15 Image rejection (Note 1) < db 15 2 -to- isolation db 2 35 -to-if isolation db 2 Output power at 1 db compression = +13 dbm dbm +1 Output two-tone third-order intercept point = +13 dbm dbm +2 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency range IRA226LC1A MHz 2 4 IRA226LC1B MHz 4 8 IRA226LC1C MHz 1 2 IF VSWR (IF = -3 dbm, = +12 dbm) Ratio 1.5:1 213

IRA226LC1A TYPICAL TEST DATA VSWR ( = +1 dbm) IMAGE REJECTION ( = +1 dbm) VSWR (RATIO) 5:1 4:1 3:1 2:1 IMAGE REJECTION (db) 1 2 3 4 1:1 2 6.8 11.6 16.4 21.2 26 5 2 6.8 11.6 16.4 21.2 26 5 CONVERSION GAIN (IF = 3 MHz, = +1 dbm) -TO- ISOLATION ( = +1 dbm) CONVERSION GAIN (db) 4 3 2 1 ISOLATION (db) 2 4 6 8 2 6.8 11.6 16.4 21.2 26 1 2 6.8 11.6 16.4 21.2 26 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion gain and -to- isolation. OUTLINE DRAWING TERMINATION (5 OHMS) MOUNTING HOLES.1 [2.54] DIA. THRU TYP. 4 PLACES.5 [12.7] 1. [25.4].25 [6.35] > < IN 2.5 [63.5] HAUPPAUGE, N.Y. 11788 MADE IN USA M/N XXXXXX S/N XXXXXX.75 [1.91] 2.35 [59.69] IF OUT IN +VDC CONNECTORS SMA FEMALE (TYP. 3 PLACES).25 [6.35] 2. [5.8].5 [12.7].25 [6.35].24 [6.1].3 [.76] DIA. X.25 [6.35] LG. (TYP. 2 PLACES) 1. [25.4] 1.625 [41.28] 1.75 [44.45] FINISH: NICKEL NOTE: All dimensions shown in brackets [ ] are in millimeters. 214

5.4 TO 5.9 GHz IMAGE REJECTION MIXER/IF AMP MODELS: IRA5459LR1A, IRA5459LR1B AND IRA5459LR1C FEATURES / coverage... 5.4 to 5.9 GHz IF operation... 2 to 2 MHz power range... +7 to +1 dbm Conversion gain... 27 db typical Image rejection... 22 db typical Image rejection mixers are useful for wideband test equipment or ultra-broadband receivers requiring rejection of an unwanted sideband of signal or noise following a low-noise front-end amplifier. The IRA Series of image rejection mixers has an integrated IF amplifier, thus making the overall sensitivity less dependent on the load noise. Now available with sideband selection switch, contact factory. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 5.4 5.9 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 5.4 5.9 power range dbm +7 +1 VSWR Ratio 2:1 Bias +15 Volts ma 15 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion gain db 25 27 Single-sideband noise figure at 25 C db 6 7 Image rejection (Note 1) db 2 22 -to- isolation db 2 25 -to-if isolation db 2 22 Output power at 1 db compression point dbm +3 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency range IRA5459LR1A MHz 2 4 IRA5459LR1B MHz 4 8 IRA5459LR1C MHz 1 2 IF VSWR (IF = -1 dbm) Ratio 1.5:1 215 1 Davids Drive, Hauppauge, NY 11788 TEL: (631) 439-922 FAX: (631) 436-743 www.miteq.com Revised: 6/18/12

IRA5459LR1A TYPICAL TEST DATA -TO- ISOLATION ( = +7 dbm) IMAGE REJECTION ( = +7 dbm) CONVERSION GAIN (db) ISOLATION (db) 2 4 6 8 1 5.4 5.5 5.6 5.7 5.8 5.9 5 4 3 2 1 CONVERSION GAIN ( < ) (IF = 3 MHz, = +7 dbm) 5.37 5.47 5.57 5.67 5.77 5.87 IMAGE REJECTION (db) NOISE FIGURE (db) 2 4 6 8 1 5.43 5.53 5.63 5.73 5.83 5.93 1 8 6 4 2 NOISE FIGURE VS. FREQUENCY ( = +7 dbm, IF = 3 MHz) 5.4 5.5 5.6 5.7 5.8 5.9 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C NOTE: Test data supplied at 25 C; conversion gain, noise figure, image rejection and -to- isolation. OUTLINE DRAWING Revised: 7/1/13 1. [25.4].67 [17.2] 1. [25.4] 2. [5.8].38 [9.65] TYP. 2.38 [6.45] NOTE: All dimensions shown in brackets [ IF GND +V IF +V 1.63 [41.4] GND.25 [6.35].38 [9.65].26 [6.6] ] are in millimeters..67 [17.2] 1.75 [44.45] ±.1 [2.54].69 [17.53].125 [3.18] 2.125 [53.98] ±.1 [2.54].125 [3.18] #6-32 NC-2 TAP X.25 [6.35] DP. MIN. C BORE.171 [4.35] DIA. X.62 [1.57] DP. NEAR SIDE, (4 PLACES) TYPE SMA FEMALE CONNECTORS, TYP. 3 PLACES 1 Davids Drive, Hauppauge, NY 11788 TEL: (631) 439-922 FAX: (631) 436-743 www.miteq.com 216

8.5 TO 9.6 GHz IMAGE REJECTION MIXER/IF AMP MODELS: IRA8596LR1A, IRA8596LR1B AND IRA8596LR1C FEATURES / coverage... 8.5 to 9.6 GHz IF operation... 2 to 2 MHz power range... +7 to +1 dbm Conversion gain... 23 db typical Image rejection... 22 db typical Image rejection mixers are useful for wideband test equipment or ultra-broadband receivers requiring rejection of an unwanted sideband of signal or noise following a low-noise front-end amplifier. The IRA Series of image rejection mixers has an integrated IF amplifier, thus making the overall sensitivity less dependent on the load noise. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 8.5 9.6 VSWR ( = -1 dbm) Ratio 2:1 frequency range GHz 8.5 9.6 power range dbm +7 +1 VSWR Ratio 2:1 Bias +15 volts ma 15 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion gain db 2 23 Single-sideband noise figure at 25 C db 6.5 7.5 Image rejection (Note 1) db 2 22 -to- isolation db 2 25 -to-if isolation db 2 22 Output power at 1 db compression point dbm +3 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency IRA8596LR1A MHz 2 4 IRA8596LR1B MHz 4 8 IRA8596LR1C MHz 1 2 IF VSWR (IF = -1 dbm) Ratio 1.5:1 217 1 Davids Drive, Hauppauge, NY 11788 TEL: (631) 439-922 FAX: (631) 436-743 www.miteq.com Revised: 7/9/13

IRA8596LR1B TYPICAL TEST DATA 5:1 AND VSWR ( = +6 dbm) IMAGE REJECTION ( = +6 dbm) CONVERSION GAIN (db) VSWR (RATIO) 2 4:1 4 3:1 6 2:1 8 1 1:1 8.5 8.78 9 9.22 9.44 9.66 5 4 3 2 1 -TO-IF CONVERSION GAIN ( < ) (IF = 6 MHz, = +6 dbm) 8.5 8.72 8.94 9.16 9.38 9.6 IMAGE REJECTION (db) NOISE FIGURE (db) 1 2 3 4 5 8.5 8.72 8.94 9.16 9.38 9.6 1 8 6 4 2 NOISE FIGURE VS. FREQUENCY ( = +6 dbm, IF = 6 MHz) 8.5 8.72 8.94 9.16 9.38 9.6 MAXIMUM RATINGS Specification temperature... +25 C Operating temperature... -54 to +85 C Storage temperature... -65 to +125 C GENERAL NOTE 1. Standard catalog unit aligned and tested for guaranteed > performance. < guaranteed performance is available, please contact MITEQ. NOTE: Test data supplied at 25 C; conversion gain, noise figure and image rejection. OUTLINE DRAWING Revised: 7/1/13 1. [25.4].67 [17.2] 1. [25.4] 2. [5.8].38 [9.65] TYP. 2.38 [6.45] NOTE: All dimensions shown in brackets [ IF GND +V IF +V 1.63 [41.4] GND.25 [6.35].38 [9.65].26 [6.6] ] are in millimeters..67 [17.2] 1.75 [44.45] ±.1 [2.54].69 [17.53].125 [3.18] 2.125 [53.98] ±.1 [2.54].125 [3.18] #6-32 NC-2 TAP X.25 [6.35] DP. MIN. C BORE.171 [4.35] DIA. X.62 [1.57] DP. NEAR SIDE, (4 PLACES) TYPE SMA FEMALE CONNECTORS, TYP. 3 PLACES 1 Davids Drive, Hauppauge, NY 11788 TEL: (631) 439-922 FAX: (631) 436-743 www.miteq.com 218

2 TO 4 GHz W-NOISE RECEIVER FRONT ENDS MODELS: ARM24LC2A, ARM24LC2B AND ARM24LC2C FEATURES / coverage... 2 to 4 GHz Conversion gain... 3 db typical Noise figure... 1.8 db maximum MITEQ s Model AR Series offers state-of-the-art low-noise amplifiers integrated with our ultra-small image rejection mixers to provide a complete receiver front-end assembly. This device comes in a nonhermetic housing, however a hermetically-sealed housing is available for extreme environmental conditions. ELECTRICAL SPECIFICATIONS INPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. frequency range GHz 2 4 VSWR ( = -1 dbm, = +1 dbm) Ratio 2.5:1 frequency range GHz 2 4 power range dbm +1 +13 VSWR ( = +1 dbm) Ratio 2.5:1 DC power +15 VDC ma 15 219 TRANSFER CHARACTERISTICS CONDITION UNITS MIN. TYP. MAX. Conversion gain (Note 1) db 27 3 Single-sideband noise figure at 25 C db 1 1.8 Image rejection (Note 1) db 18 2 -to- isolation db 4 -to-if isolation db 25 -to-if isolation db 25 Output power at 1 db compression dbm 6 Output two-tone third-order intercept point dbm 16 OUTPUT PARAMETERS CONDITION UNITS MIN. TYP. MAX. IF frequency range ARM24LC2A MHz 2 4 ARM24LC2B MHz 4 8 ARM24LC2C MHz 1 2 IF VSWR (IF = -1 dbm, = +1 dbm) Ratio 2:1 Revised: 7/13/11

2024 © artsdocbox.com Privacy Policy | Terms of Service | Feedback