TS-PMB_bro_en_0758-0600-12.indd 1 Product Brochure 02.00 Test & Measurement Switch Matrix Module High-density, 90-channel, full matrix relay multiplexer module
Switch Matrix Module At a glance Typical applications are production tests in the fields of communications, automobile electronics and general industry electronics, particularly analog in-circuit tests with a large number of channels. The switch matrix module can be used in the R&S CompactTSVP and R&S PowerTSVP. It is a CAN bus controlled module which takes up only one slot. Built-in selftest capability in conjunction with the R&S TS PSAM makes it possible to fully check the module within the system. The matrix module allows test points or test devices to be interconnected either locally or via the analog R&S TSVP interconnection subsystem. Key facts General purpose switch matrix module Control interface based on CAN bus Input signals up to 125 V, up to 1 A Switchable signal ground via relay Selftest capability Fast switching of signal paths Cost-efficient design based on integrated relay cluster Configurations include Single matrix with 90 pins to 4 bus lines Single matrix with 45 pins to 8 bus lines Dual matrix with 45 pins to 4 bus lines Analog measurement bus access to 8 bus lines LabWindows/CVI device driver support GTSL test software library in DLL format EGTSL test software library for in circuit test (ICT) Functional block diagram of the IL2 IL1 Analog bus X30 Coupling relays IL1 IL2 IL3 Local analog bus (LAB) Instrument Lines P1 P2 P3 P4 PXI trigger logic Relay control Pin relays P89 P90 SPI Microcontroller Extension connector X20 LABD1 ABD1 LABC2 ABC2 LABC1 ABC1 LABB1 ABB1 LABB2 ABB2 LABA2 ABA2 LABA1 ABA1 LABD2 ABD2 Analog bus (AB) CAN RAM Sense relays CHA- NO lines 2 TS-PMB_bro_en_0758-0600-12.indd 2
Sophisticated signal routing Typical applications The matrix module allows test devices to be connected to any DUT pins, either locally within the module or throughout the entire instrument by using the R&S TSVP analog bus. Connection/multiplexing of DUT signals to test devices Interconnection of test points locally or via the analog bus Configuration of scalable matrices, from a simple multiplexer to a matrix for numerous measurement devices ICT (in-circuit test) with up to 6-wire measurements Parallel testing through the use of two 4-wire systems Remote switch matrix in fixtures without R&S TSVP Due to the full matrix configuration of the module, no restrictions are placed on how DUT fixtures are wired or how the switching paths are established. Measurement instruments can be connected to the rear panel of the R&S TSVP to avoid cross wiring at the fixture interface. Software support The compact design allows the configuration of test systems with several PXI devices and high-pin count multiplexing in a single unit (one-box solution). This is especially advantageous for functional testing in fully automated test equipment and in-line test solutions. The interconnection solution of the R&S TSVP analog bus is based on the best way of handling analog signals. The analog bus is located immediately above the front connector area where space is provided for on-board signal conditioning and signal routing by coupling relays for the analog bus. This distance to the high-speed PCI bus significantly improves signal quality. A LabWindows/CVI DMM driver in line with the IVI standard is available for the module switching functions. Function panels and online help are available as common features for the LabWindows/CVI driver. The ICT is performed with a dedicated software package, the enhanced generic test software library (EGTSL). Selftest and diagnostics for reliable operation The built-in selftest capability of the module ranges from fast diagnostics to the complete, automated evaluation of all relays and switching paths (R&S TS PSAM required). Diagnostic LEDs on the front panel speed up system integration and allow proper operation to be determined at a glance. Additionally, the dedicated switching modules such as the are controlled via the low-noise, interference-resistant CAN bus, which ensures overall high reliability and signal quality. TS-PMB_bro_en_0758-0600-12.indd 3 Rohde & Schwarz Switch Matrix Module 3
Specifications Specifications Application in R&S TSVP platform R&S CompactTSVP or R&S PowerTSVP 1 slot required Interface Control bus CAN 2.0b (1 Mbit/s) DUT connector (front) DIN 41612, 96 pins Rear I/O connector CompactPCI connector J2, 110 pins Switching characteristics 1) Switching voltage DC/AC (RMS) 125 V/125 V (max.) Switching current DC/AC (RMS) 1 A/1 A (max.) Switching power 10 W/10 VA (max.) Switching time (includes bouncing) 0.5 ms (typ.) Path resistance < 2 Ω/0.5 Ω (typ.) Ground relay 2) Max. voltage DC/AC (RMS) 125 V/125 V (max.) Max. current (switched) DC/AC (RMS) 2 A/2 A (max.) Max. switching power 60 W/60 VA (max.) Switching configurations Analog measurement bus access 8 lines Input pins 90 Instrument lines Configurable as 3 to 8 analog bus lines dual matrix 45 pins to 4 bus lines single matrix 90 pins to 4 bus lines single matrix 45 pins to 8 bus lines Mode of coupling relays local or global Transfer characteristics 3) Crosstalk (channel-to-channel, typ., 50 Ω) 1) Frequency Crosstalk 10 khz 80 db 100 khz 65 db 1 MHz 40 db 10 MHz 10 db All data, carried and switched, resistive load. Data for resistive load. Single module data, typical values. 2) 3) TS-PMB_bro_en_0758-0600-12.indd 4 Rohde & Schwarz Switch Matrix Module 4
General data Power consumption 5 V/4.2 A (max.) Power consumption for 0 to all relays active 0.5 W to 22 W (max.) Environmental conditions Temperature operating temperature range +5 C to +40 C storage temperature range 10 C to +60 C Damp heat +40 C, 80 % rel. humidity, steady state, in line with EN 60068-2-30 Mechanical resistance Vibration sinusoidal 5 Hz to 55 Hz, 0.15 mm amplitude const., 55 Hz to 150 Hz, 0.5 g const., in line with EN 60068-2-6 10 Hz to 300 Hz, acceleration 1.2 g (RMS), in line with EN 60068-2-64 40 g shock spectrum, in line with MIL-STD-810E, method 516.4, procedure I random Shock Product conformity Electromagnetic compatibility EU: in line with EMC Directive 2004/108/EC Electrical safety EU: in line with Low Voltage Directive 2006/95/EC W H D Dimensions applied harmonized standards: EN 61326-1 (industrial environment), EN 61326-2-1, EN 55011 (class A), EN 61000-3-2, EN 61000-3-3 applied harmonized standard: EN 61010-1 Weight 316 mm 174 mm 20 mm (12.44 in 6.85 in 0.79 in) 0.75 kg (1.65 lb) Calibration not required Ordering information Designation Type Order No. Switch Matrix Module 1143.0039.02 R&S CompactTSVP Test and Measurement Chassis R&S TS-PCA3 1152.2518.02 R&S PowerTSVP Industrial Switching Application Chassis R&S TS-PWA3 1157.8043.02 TS-PMB_bro_en_0758-0600-12.indd 5 Rohde & Schwarz Switch Matrix Module 5
Service that adds value Worldwide Local and personalized Customized and flexible Uncompromising quality Long-term dependability About Rohde & Schwarz Rohde & Schwarz is an independent group of companies specializing in electronics. It is a leading supplier of solutions in the fields of test and measurement, broadcasting, radiomonitoring and radiolocation, as well as secure communications. Established more than 75 years ago, Rohde & Schwarz has a global presence and a dedicated service network in over 70 countries. Company headquarters are in Munich, Germany. Environmental commitment Energy-efficient products Continuous improvement in environmental sustainability ISO 14001-certified environmental management system Certified Quality System ISO 9001 Rohde & Schwarz GmbH & Co. KG www.rohde-schwarz.com R&S is a registered trademark of Rohde & Schwarz GmbH & Co. KG Trade names are trademarks of the owners PD 0758.0600.12 Version 02.00 December 2013 (wb) Data without tolerance limits is not binding Subject to change 2004-2013 Rohde & Schwarz GmbH & Co. KG 81671 München, Germany 0758.0600.12 02.00 PDP 1 en Regional contact Europe, Africa, Middle East +49 89 4129 12345 customersupport@rohde-schwarz.com North America 1 888 TEST RSA (1 888 837 87 72) customer.support@rsa.rohde-schwarz.com Latin America +1 410 910 79 88 customersupport.la@rohde-schwarz.com Asia/Pacific +65 65 13 04 88 customersupport.asia@rohde-schwarz.com China +86 800 810 8228/+86 400 650 5896 customersupport.china@rohde-schwarz.com 0758060012 TS-PMB_bro_en_0758-0600-12.indd 6 17.12.2013 10:42:40