Installation and Operating Instructions
The information provided in these installation instructions may be modified without prior notification. All previous versions cease to be valid with the publication of these instructions. The information in these installation instructions has been compiled in good faith and based on the best knowledge available to us. DORMA accepts no liability for the correctness and completeness of the details provided. In particular, DORMA cannot accept liability for any consequential damages due to incorrect or incomplete information. The recommendations for installation made in this manual are based on the assumption that prevailing basic conditions are favourable. DORMA accepts no liability for the perfect functioning of the S6-R Reader in external, non-system environments. Despite every effort to prevent mistakes, they can never be completely avoided. Therefore, we would be grateful to receive notification of any errors or omissions. DORMA accepts no liability for the information included in this document being free of protected third party rights. DORMA does not provide any licences for its own or third party patents or other protected rights with this document. It is not permitted to print, reproduce or to pass on this manual, or parts thereof, to third parties, other than for your own use, without the approval of DORMA. All rights reserved. DORMA Time + Access GmbH Postfach 21 01 85 53156 Bonn http://www.dorma-time-access.de E-Mail info@dorma-time-access.de Copyright 2014 by DORMA Time + Access GmbH
Contents 1. General Information....4 1.1 Preface...4 1.2 Correct usage...4 1.3 Safety precautions....4 1.4 Further Sources of Information...5 1.5 Disposal...5 1.6 Functional principle....5 1.7 Read procedure....6 1.8 S6-R Reader System55 delivery package....7 1.9 S6-R Reader Protect delivery package....7 1.10 S6-R Reader TX44 delivery package...7 1.11 S6-R Reader Siedle 611 delivery package...8 1.12 Installation accessories (optional)...8 2. Installation...9 2.1 Requirements for trouble-free operation....9 2.2 Preparation...9 2.5 RS485-Bus....11 2.6 S6-R Reader System55 final installation...11 2.7 TX44 final installation...12 2.8 Protect final installation....13 2.9 Front film for S6-R Reader Protect...14 2.10 Siedle 611 final installation...15 3 Commissioning... 16 3.1 Settings...16 3.2 Signalling...17 4. Service...18 4.1 Firmware...18 4.2 S6-R Reader System55 tampering protection....18 4.3 Antenna trimmer...18 5. Technical Data...19 EC Declaration of Conformity...20 2.3 Connection of S6-R Readers....10 2.4 Power supply...11 DORMA 3
1. General Information 1.1 Preface This installation manual is intended to help you connect and put into operation the S6-R Reader. 1.2 Correct usage This device is intended exclusively for use in attendance recording and access control systems. Further details are described in Chapter 1.6. Use for any other purpose than the one described is not permitted. 1.3 Safety precautions This device has been constructed and tested in accordance with all currently applicable technical regulations. It left the factory with all safety features in perfect working order. To maintain this condition and to ensure risk-free operation, the user must observe the instructions and warnings given in this operating manual. Installation and assembly of electrical equipment may only be carried out by a qualified electrician. During installation, please ensure that the requirements specified in the relevant equipment safety standard for the unit are adhered to since non-compliance could affect the safety of the device. Before switching on, ensure that the operating and control voltages connected do not exceed the permissible levels as specified in the technical data. This unit conforms to EN 60950, protection class III. The units must be operated using a safety extra-low voltage (SELV). Electromagnetic compatibility: The unit is designed for use in residential, commercial and light-industrial environments. The PCB can be damaged by static electricity discharge, so relevant precautionary measures must be observed, such as grounding. These units must not be operated until they are fully installed. If you believe that safe operation is no longer possible, take the unit out of operation and secure it against accidental use. If a failure or malfunction in the unit might result in injury to persons or animals or in damage to works equipment, such damage or injury must also be prevented by taking additional safety measures, such as installing limit switches and safety devices. Switch off the power supply before opening the device. 4 DORMA
1.4 Further Sources of Information The S6-R reader is operated within an access-control system. The documentation for the following system components must be observed. DORMA EAC hardware manual Access control software (host) 1.5 Disposal This device has been manufactured using high-quality materials and components that can be recycled. Information for EU Countries This device is subject to European Directive 2002/96 EC and therefore must be disposed of separately from household waste. As the manufacturer, we will take back our electric and electronic products and dispose of them for you free of charge. Alternatively, you may also contact your waste disposal company. 1.6 Functional principle The S6-R Reader reads ID card data using a contactless connection and sends data to a higher level control unit, where they are evaluated to check whether the ID card is authorised or not. The result is sent to the S6-R Reader, which emits a visual and audible signal to indicate authorisation or not. The control unit communicates with the S6-R Readers via an RS485 bus. DORMA 5
ST102 1.7 Read procedure The type of read procedure supported is indicated by the type key on the nameplate. The positions of the nameplate are shown in the graphics to the right. S6-R-Reader System55 S6-R-Reader TX44 5P93EN2N1 Code PX51 PX71 PX10 Leseverfahren Legic advant / prime Mifare Desfire / Classic Hitag S6R-0-G#-PX##P1-0-0-3-24V 9V-40VDC, 110mA-30mA ## XXXXXXXX-XXXXX-XXX XX S6-R-Reader Protect S6-R-Reader Siedle 611 6 DORMA
1.8 S6-R Reader System55 delivery package A 1x S6-R-Reader System55 B 1x manual A B S6-R READER Installation and Operating Instructions 1.9 S6-R Reader Protect delivery package A 1x reader with 4 m connection cable B 1x manual C 1x front foil D 2x Spax screws (3 x 30 mm) E 2x plastic wall plugs (6 mm) F 2x tapping screws (3.2 x 25 mm) A B C S6-R READER Installation and Operating Instructions D F 2x 2x E 2x 1.10 S6-R Reader TX44 delivery package A 1x Surface-mount casing TX44 B 1x S6-R-Reader C 1x manual A B C S6-R READER Installation and Operating Instructions DORMA 7
1.11 S6-R Reader Siedle 611 delivery package A 1x S6-R-Reader Siedle 611 B 1x manual A B S6-R READER Installation and Operating Instructions 1.12 Installation accessories (optional) A S6-R Reader Protect spacer frame (Item no. 19210601). The spacer frame enables the reader to be surface-mounted or mounted on metal plates (see Chapter 2.7). A C B Surface-mount casing for S6-R Reader System55 1) The surface-mount casing is used to surface-mount S6-R Reader System55. C System55 combination frame 1) 2) The combination frame is always required whenever the reader is flush-mounted. B You can find more installation accessories in our catalogues. 1) Available in different colours 2) Single or multiple frame 8 DORMA
2. Installation 2.1 Requirements for trouble-free operation The following environmental factors may affect the range and functions of the contactless read procedure. Metal There must be no metal objects such as metal wall panelling within a square area measuring 120 x 120 mm and 30 mm deep. Adequate clearance must be ensured at the planning or installation stage. The reader range is reduced if the clearance distance cannot be complied with. 120mm 120mm 30mm Antenna field of another reader To prevent mutual interference, you must not install two readers closer to each other than the minimum specified distance. The minimum distance depends on local conditions, but it should always be greater than 50 cm. min. 50cm 2.2 Preparation 2.2.1 Wall box A wall box (flush-mount or pattress box) is required to install S6-R Readers. The flush-mount or pattress box design must comply with DIN 49073-1. To ensure correct installation, the flush-mount box may only be fitted a maximum of 4 mm behind the wall surface or plasterwork and must be installed in a vertical position in the wall. The front edge may only vary a maximum of 1.5 mm from a straight line parallel with the wall surface. min. 50cm 2.2.2 Cabling Connecting cables must feature a maximum cross-section of 1.5 mm². Data cables should consist of shielded twistedpair cabling with an impedance of 120 Ω. Detailed information regarding cable types and lengths and other specifications for the planning of access systems using our components are included in our DORMA EAC Hardware manual. DIN 49073-1 DORMA EAC Hardware manual DORMA EAC Hardware manual DORMA 9
2.3 Connection of S6-R Readers 10 mm S6-R-Reader System55, TX44, Siedle 611 S6-R-Reader Protect connection cable 2.3.1 Push Terminal ST201 (System55) This push terminal is bus compatible. Cables are looped through the inside of the terminal. The bus is not interrupted when the terminal is removed from the S6-R Reader. Connection specifications Cable type Cable cross-section rigid / flexible 0,2-1,5mm² (AWG 24-16) Plug in rigid max. 2,5 mm 1. 10 mm 10 mm Flexible with wire end sleeve, no plastic sleeve Flexible with wire end sleeve, with plastic sleeve 0,5-1,5mm² 0,5mm² 2. Plug in flexible max. 2,5 mm 1. 10 mm max. 2,5 mm 2. optional 1. 10 mm Remove rigid and flexible max. 2,5 mm 2. 1. 2. 10 DORMA max. 2,5 mm 1.
2.4 Power supply The S6-R Reader s power supply is connected to Terminal 1 and Terminal 3 on the ST201, or to the brown and white wires in the connecting cable (S6-R Reader Protect). The voltage must be between 9 V and 40 VDC. S6-R-Reader System55 A+ B- 1 / 24V 3 / 0V ST201 The S6-R Reader must be connected in a de-energised state only. 2.5 RS485-Bus S6-R-Reader Protect The RS485 bus line is connected to Push Terminals ST201 Signals A+ and B-, or to the green and yellow wire in the connecting cable (S6-R Reader Protect). Signal 24V Wire colours brown A+ green B- yellow 0V white 2.6 S6-R Reader System55 final installation 1. 2. 3. DORMA 11
2.7 TX44 final installation 1. 2. 3. 4. ø6mm 5. 6. 2. 4. 1. 6. 5. 3. 12 DORMA
m 30mm S6-R READER ø6mm 2.8 Protect final installation Installation in flush-mount box S6-R Reader Protect Wall Flush-mount box Installation surface S6-R Reader Protect Montagefläche Installation directly on wall Spacer frame S6-R Reader Wall Protect Cable duct 1A 30mm 2A S6-R-Leser Protect Abstandsrahmen 30mm S6-R-Leser Protect Kabelkanal Wand Unterputzdose ø6mm Installation with cable duct Installation surface 1B 60mm S6-R Reader Protect Spacer frame ø3mm Cable duct ø3mm 2B 3B 60mm ø3mm Spacer frame for Protect Reader (Item no. 1910601) ø3mm Protectleser-Abstandsrahmen (Art.-Nr. 1910601) DORMA 13
Installation on metal plate 1C Metal 60mm S6-R Reader Protect ø3mm Spacer frame ø3mm 2C Use screws F when installing in a pattress box and with spacer frame 60mm ø3mm ø3mm 2.9 Front film for S6-R Reader Protect Once S6-R Reader Protect has been successfully put into operation, the front must be cleaned with a silicon remover and the self-adhesive film affixed to the exposed section. You must do this very carefully to ensure that protection rating IP65 is complied with. Caution: If you remove the self-adhesive film, it cannot be re-used. A new film must be affixed. You can order a replacement film from DORMA, by specifying item number third Spacer frame 1900004912499 in your order. 14 DORMA
2.10 Siedle 611 final installation 1. 2. 2. 1. 3. 4. 1. 2. 5. DORMA 15
3. Commissioning 3.1 Settings SW201 SW201 SW201 1 2 3 4 5 6 7 8 Function Bus adress Configuration protection Bus terminating resistor Bus Address The bus address can be set with the 8-pin DIP Switch SW201. 31 addresses are available. The address 00 is reserved for thecontrol unit. SW201 1 2 3 4 5 Adress (decimal) off off off off off unzulässig on off off off off 01 off on off off off 02 on on off off off 03 off off on off off 04 on off on off off 05 off on on off off 06 on on on off off 07 off off off on off 08 on off off on off 09 off on off on off 10 SW201 1 2 3 4 5 Adress (decimal) on on off on off 11 off off on on off 12 on off on on off 13 off on on on off 14 on on on on off 15 off off off off on 16 on off off off on 17 off on off off on 18 on on off off on 19 off off on off on 20 on off on off on 21 SW201 1 2 3 4 5 Adress (decimal) off on on off on 22 on on on off on 23 off off off on on 24 on off off on on 25 off on off on on 26 on on off on on 27 off off on on on 28 on off on on on 29 off on on on on 30 on on on on on 31 Configuration protection DIP switch 6 of SW201 activates configuration protection. When configuration protection is activated, the configuration cannot be changed or deleted. SW201 6 Configuration protection off on off activ Bus terminating resistors The bus terminating resistors must be switched on if the S6R Reader is the first or last bus device. The configuration protection function is only available with firmware V3.30 or later. Switch 6 is set ex works, and its position should not be changed. An incorrect setting can make the S6R reader unusable! Configuration protection may only be deactivated if the "Load IdendAssembler" system parameter is activated in DORMA MATRIX. 16 DORMA
3.2 Signalling Audible signalling device Online-LED Read-LED Audible signalling device Online-LED Read-LED 3.2.1 Online-LED Online LED Meaning Remark Off No power supply Flashing yellow Offline The S6-R reader is not being polled by a superordinate control unit Illuminate yellow Online The S6-R reader is being polled by a superordinate control unit 3.2.2 Read-LED and audible signals Read-LED Buzzer Meaning Remark Off No booking activity Illuminated green Illuminated red Flashing yellow 1) Flashing yellow + Illuminated green 1) emits a signal for one second emits an intermittent signal for one second emits a short signal every second 1) Authorised booking Unauthorised booking and possibly unrecoverable AoC error AoC write operation Authorised booking despite AoC error Flashing yellow + Illuminated red 1) Temporary AoC error In the case of a temporary error, e.g. due to premature removal of an ID card, it makes sense to repeat the booking Attention: The signals described here are default values. The actual signalling may deviate as a result of modifications to the TP4 terminal configuration! 1) Only if the signalling is activated in the TP4 class konfiguration. DORMA 17
4. Service 4.1 Firmware Plug ST101 is used as an interface for any necessary firmware updates. Light barrier for tampering protection 4.2 S6-R Reader System55 tampering protection A light barrier providing tampering protection is integrated into the S6-R Reader System55. This barrier sends a signal to the higher level control unit if the cover is opened. 4.3 Antenna trimmer This device is optimally adjusted on site and should not be moved. ST101 Antenna trimmer Antenna trimmer ST101 18 DORMA
5. Technical Data Supply voltage 9 V to 40 VDC (SELV) Power consumption 1.2 W; 40 ma at 24 V max. 110 ma at 9 V Reader systems The following reader systems are available, depending on the model: MIFARE (Classic, DESFire) LEGIC (prime, advant) Transmission frequency: 13.56 MHz HITAG Transmission frequency: 125 khz Read range: 2-5 cm The specified read distances are standard distances. They may vary, depending on the ID card type, installation frame and any surrounding metal parts. Anti-tamper contact System55/TX44: Reflected-light barrier Siedle 611: Button Interfaces 1 x RS485 (DP1) Display elements 1 x LED (online) 1 x LED (read) 1 x audible signal unit Operating temperature 20 C to +50 C Storage temperature 20 C to +70 C General design EN 60 950-1, protection class III Protection rating S6-R Reader System55: IP30 S6-R Reader Protect: IP65 S6-R Reader TX44: IP44 S6-R Reader Siedle 611: IP54 Resistance to interference EN 301 489-1, -3 EN 61000-6-2 Interference emissions EN 300 330 EN 301 489-1, -3 Radio range EN 300330-2 Dimensions S6-R Reader System55: B71 x H71 x T24 S6-R Reader Protect: B81 x H81 x T20 S6-R Reader TX44: B71 x H71 x T24 S6-R Reader Siedle 611: B101 x H101 x T24 Weight S6-R Reader System55: 70g S6-R Reader Protect: 280g, including connecting cable S6-R Reader TX44: 70g S6-R Reader Siedle 611: 116g We reserve the right to make technical modifications and improvements that assist the further development of our equipment. DORMA 19
EC Declaration of Conformity 20 DORMA
DORMA 21
EC Declaration of Conformity 125 khz in preparation System55 TX44 Siedle611 22 DORMA
EC Declaration of Conformity 125 khz in preparation Protect DORMA 23
DORMA DEUTSCHLAND GmbH DORMA Platz 1 58256 ENNEPETAL DEUTSCHLAND Tel. +49 2333 793-0 Fax +49 2333 793-4950 WWW.DORMA.DE DORMA TIME + ACCESS GMBH MAINZER STRASSE 36-52 53179 BONN DEUTSCHLAND TEL. +49 228 8554 0 FAX +49 228 8554 175 WWW.DORMA-TIME-ACCESS.DE Z.-Nr.: 1091G-00-B1-GB, 10/14 V2.0 Subject to change