of Loewe E 2.10_m1 1

of Loewe E 2.10_m1 1

Attention! After updating the M203 firmware to version 2.00 or higher, we recommend completely resetting the M203 interface by pressing the Disable softkey on setup page #2 for several seconds, until setup page #1 automatically appears. Please refer also to page 8 ff.

Content M203 - New features - Switching between stations Installation & Connection Plan Connection M51 Link IN/ OUT RS 232 IR-LINK Setup key Setup #1 slot/ serial port selection Slot address M51/M100 operation Slot address M219 operation RS232 mode Auto Standby Serial Interface RS-232 Link Video Controller & complete reset Connection plan Loewe TV with M51 Loewe TV with M219 HDMI Switcher with M51 HDMI Switcher with M219 Overview video products HDMI Switcher 4x1/4x2/6x2 Loewe TV Changing the Loewe IR code SCART connection between M51 and Loewe Setup # 2 1. Selecting audio source Unknown audio sources 2. Assigning video input Disable Setup #2 Reset Technical data Guarantee Included in delivery 3 3 4 5 5 6 6 7 7 7 8 9 9 10 11 11 12 12 12 13 14 15 15 15-16 17 18 19 19 20 21 22 22 23 23 23 1

Introduction M203 M203 Loewe With the Re:connect M203, Revox offers an interface, for the intelligent control of many of the Loewe televisions. The correct picture input is automatically selected at the television with the help of the interface. Additionally, the next or previous TV programme can be selected for the television, through the M218 wallmounted keypad. Multiroom Planer V2.00.00 The new Multiroom Planner doesn't just calculate the correct address assignment for the M219 Side room amplifiers and M217 wall-mounted displays, it also calculates the slot addresses for the M200 series Re:control products in the side room. Take advantage of the possibility to be able to determine in advance, all M203, M217 and M219 addresses simply and quickly and at the same time save the information as system documentation. You will find more information about addressing the M203 in the side room, on Page 6 of this manual. You can download the new Multiroom Planner V2.00 free-ofcharge from the download area of the Revox Homepage, under www.revox.com. New features from software V2.00 From software version 2.00, the M203 can be connected not only to an M51 but also to the M219 Side room amplifier. As a result, a Loewe television can also be controlled from an side room, using the M219 Side room amplifier. The option of connecting an M203 interface to an M219 exists with the first four Side room amplifiers for each zone. As a result, a total of 16 Side room amplifiers can be connected with an M203 interface in a Revox Multiroom system with 4 different zones. In the same way as with the setup of an M51, you define which video input at the Loewe televisions activated by which M219 audio source, through the M203 Setup. The local inputs Local 1 3 at the M219 can be used for the control, as well as the audio sources of the Multiroom Central unit. Important advice: If you want to use the software version 2.00, the complete Revox system must be updated to the level 2.00, or higher. 2

M203 Introduction Switching between stations using the Revox wall-mounted keypad The M203 offers the option of selecting specific stations using the skip keys (<>) on an M218 wallmounted keypad, once the TV tuner has been selected. This comfort function requires two settings: 1/2 Audio IN assignment M51/ M100 in combination with M203 The sound input, e.g. TV, Aux1, Optical, etc., of the remote device must be assigned to one of the following Remote buttons in the Remote menu: Local Local 1 Local 2 Local 3 TV Assignment example M219 in combination with M203 There is no need to make an assignment through the Remote menu with an M219, because its local audio inputs (Local 1-3) are always assigned to the IR commands Local, Local 1, Local 2 and Local 3. Continue with point 2/2 2/2 TV Tuner assignment M203 Setup #2 - Input The second assignment affects Setup #2 in the M203. Here, the physical audio source of the TV sound that was assigned to a Local Remote button in the first step, is assigned to the television's TV Tuner. In the example above, the audio source TV calls the television tuner. As well as the Multiroom central unit sources, a side room amplifier also offers its own local Inputs 1-3 for the TV Tuner assignment. 3

Installation & Connection M203 Installation The M203 interface can be installed easily and quickly. There are two types of fixing available. 1) The four outside fixing holes ( 4,2 mm ) are used for a permanent installation. 2) Revox recommends using the two slots on the side for a variable installation. Connection plan Re:system M51, M100 resp. Re:connect Further Re:connect products: M201, M202, etc IR-/ wall-mounted remote control M204/ M218 RS232 seriell interface Fixing hole 4,2 mm Slotted hole 4 x 20 mm / 15 mm Serial interface activity display Setup button 4

M203 Connection: M203 with M51/ M100/ M219 Socket: M51 LINK IN Setup: - M219: Yes The M203 interface is connected with the M51 LINK socket on the back of the M51 or the M219 LINK socket on the Side room amplifier, using the supplied telephone cable. If you want to use a different cable, you should only use a non-crossed, 4-core telephone cable with an RJ11 plug (6P4C modular). Max. cable length: 100 m Max. cable resistance: 0.1 Ω /m Installation & Connection Connection: M203 with external interfaces Socket: M51 LINK OUT Setup: - M219: Yes The M203 interface is designed for the connection of further external interfaces: M51/ M100 operation Currently, the following further products can be connected with the M51:: 4 M200 Domotic interface 4 M201 IR interface 4 M202 Ethernet interface 4 M203 (2. Interface) 4 M217 Display M219 operation With the M219, the LINK OUT can be used for the connection of an M217 Display. Use a non-crossed, 4-core telephone cable with an RJ11 plug (6P4C modular). Max. cable length: 100 m Max. cable resistance: 0.1 Ω /m 5

Installation & Connection M203 Connection: M203 with seriell interface Socket: RS232 Setup: # 4 from page 8 M219: Yes Using the serial RS232 inter-face, The M203 interface can be used with other (TV) devices, which also have a serial interface. Many of the Loewevideo products have a serial interface and are therefore very easy to integrate into the Revox World. The M203 Interface is also suitable as an interface to domestic facility management systems such as AMX or Crestron, which have a special Revox protocol. Even a Windows PC with the M230 control program can be connected to the serial interface on the M203. You will find further information from Page 8. Serial cables with a maximum length of 10 metres can be used. Connection: M203 with IR controller Socket: IR-Link Setup: - M219: Yes The connection to an IR receiver or a wall-mounted remote control is done through the 3-pin, screwfixable Phoenix plug connection. Revox recommends the use of a 2- core screened cable (microphone cable), where the screening is used as ground. This cable may be a maximum of 30 metres in length. Please ensure that you use the correct polarity when setting up as otherwise you might damage your equipment. Symbols: + Pos. voltage. 20V (DC) IN IR Signal - Ground The maximum number of IR receivers that can be switched in parallel per M203 is 3. 6

M203 Setup key Setup #1 Configuration @ M51, M100 Function: Addr. assignment Display: Slot Address Connection: M51-Link M219: Yes M51, M100 operation (p. 9+10) Using the Setup key, you call up the M203 menu, which is shown in the M51, M100 display. If the M203 interface is connected with an M219 Additional room amplifier, the M51 display is also used. In the case of an M10 installation, display is done using the M230 service program or M-Scope. A different address must be assigned through the slot address, if a second M203 (M200) is connected to the M51 Link output, so that both don t occupy the same slot address. This would cause errors. In the case of a double address assign-ment, neither of the two M203s (M200s) would be shown in the Version list. Slot address: #11 or #12 The two slot addresses 11 and 12 are available for selection. The following message appears if the selected address is already assigned: Using the Softkeys you can get to pages #1 and #2 Setup page #2 only appears if a video device has been selected on page #1 as Serial Port Mode. 7

Configuration M203 Setup #1 @ M219 Example M219 operation - fig. Page 9+11 In respect of the M219, the slot address defines the assignment to the Side room amplifier. A M203 can only be connected to an Side room amplifier within the address range x1 x4. In Figure A, an M203 could be connected to each of the Side room amplifiers 31 34. The M219 amplifiers 35 and 38 on the other hand may not be connected with an M203 interface. Fig A. Multiroom version list / Zone 3 The slot address defines which Side room amplifier the M203 interface should communicate with. This is necessary because of the bus system, although in each case, the M203 is individually connected with the M219. Only one M203 interface can be used per Side room amplifier. Address assignment : Zone 1-4 M219/ 217 M200/ M203 x 1 x 11 x 2 x 12 x 3 x 13 x 4 x 14 x 5 x 6 x 7 x 8 The figure below shows the Multiroom version list from Zone 3 for the M203 interfaces. You get to this menu by repeatedly pressing the Zone softkey in the sub-menu (M51, M230 etc.) of: Setup Multiroom Version Zone x In this case, an M203 interface was assigned to the Side room amplifier with address 4, through the slot address 314. Amplifiers 1 3 do not have an M203. Fig B. Multiroom version list / Zone 3 x 1 x 4: x 5 x 8: x 11 x 14: only M219 M217 or M219 only M200 / M203 8

M203 Setup #1 RS232 Modus Function: RS232 interface Display: Serial Port Mode Connection: RS232 M219: Yes The function of the serial interface (Serial Port) can be configured for the following applications: RS-232 Link HDMI CLUX 41AT HDMI CLUX Cx1C Gefen HDMI Switcher 4x2 Gefen HDMI Switcher 6x2 Loewe* L27xx Loewe* SL1xx Loewe* SL2xx Loewe* SL3xx In order to ensure problem-free operation, the Loewe TVs has to be equipped with the latest SW version with date June 2016 or later. Please take note of the important information on page 8 relating to a complete reset of the M203. Setup #1 Auto Standby Function: Auto Standby Display: Auto Standby Connection: RS232 M219: Yes Configuration The Auto Standby function enables the TV to remain switched on, even in the case of selected audio sources that do not activate a video input at the TV, e.g. the M51 radio tuner. The Auto Standby option is only shown in the menu if Loewe has been selected as Serial Port Mode. Auto Standby: ON The television switches itself off automatically as soon as an audio source is selected, which either cannot activate a video input, e.g. Tuner, or which is disabled Auto Standby: OFF After the television has been switched on, it remains on permanently until the M51/ M100/ M219 is switched off, irrespective of which audio source is selected. 9

Configuration M203 RS-232 Link. Standardised serial interface (RS232 protocol) for connection to a PC or another serial interface. Application: You should select this setting if you want to use the M230 control program for PCs or if you want to access the Revox System through domestic facility management equipment such as Crestron and AMX. 10

M203 Configuration Video Controller. If a video controller for a video product was selected on page #1 Port Mode, a second menu page, Setup # 2 is available. This page enables you to selectively switch on and/or between video inputs on a Loewe device or an HDMI Switcher, dependant on the selected M51/ M100 or M219 source. The convenient integration can of course also be used for the M51 s integrated DVD player. Please refer to the picture on the next page Connection : Video 1). The audio source and video input links referred to in the example are defined in Setup #2. You will find an exact description of the links, starting from page 16. Example M200 with M51: A SAT receiver can conveniently be integrated through the automatic selection of the video input on the TV by the M51. Its picture output is connected, for example, to the HDMI- 1 input on the Loewe TV, while the audio signal is connected to the Optical input on the M51. Please also refer to the picture on the next page. If you now select the source SAT (Optical) at the M51, the Loewe TV automatically transmits the SAT receiver picture over the input HDMI-1 and the sound from the SAT receiver is transmitted over the M51. Complete reset? Yes You should always carry out a complete reset with each new configuration as well as when changing to another TV model. To do this, press the Disable softkey on Setup page #2 and keep it pressed, until the system automatically returns you to page 1. No A complete reset is not necessary with an assignment change within a TV model. 11

Configuration M203 Connection A plan: Loewe TV (L2700) with M51 Connection plan: Loewe TV (L2700) with M219 12

M203 Configuration Connection A plan: HDMI-Switch (Gefen, CLUX) with M51/ M100 Note The HDMI output on the M51 is only available if the DVS module is installed Gefen : Registered trademark of the Gefen Company/US 13

Configuration M203 Connection plan: Gefen, CLUX HDMI switcher with M219 14

M203 Configuration Gefen HDMI Switcher CLUX HDMI Switcher Loewe TV L27xx The HDMI inputs on the HDMI switcher are activated, dependant on the audio source. If there is no assignment, the HDMI input that was last selected remains active. Setting is done on page #2 in the M203 Setup Product features: - 4 HDMI inputs (4x1, 4x2) - 6 HDMI inputs (6x2) A crossed Sub-D cable (plug plug) is required for the transmission. Type: Plug-Plug For this reason, you should use the enclosed crossover adapter and gender adapter with the supplied Revox cable. + The designation L2700 describes the chassis electronics of the Loewe television and not the television type. Various Loewe televisions with L2700* electronics or higher, e.g. L2710, have had a serial interface for control purposes since 2007. The chassis version can be checked in the Loewe television Service menu. The Loewe televisions with chassis electronics L2700 or higher require a crossover serial cable, also known as a null modem cable, as the control cable between the M203 and the Loewe television. Connection type: Plug - Plug For this reason, you should use the enclosed crossover adapter with the supplied Revox 1:1 cable 9-Pol 9-Pol Pin 2 Pin 3 Pin 3 Pin 2 Pin 5 Pin 5 Max. cable length RS232: 10 m Gefen products are freely available through specialist retail outlets. 15 9-Pol 9-Pol Pin 5 Pin 5 Pin 2 Pin 3 Pin 3 Pin 2 Max. cable length RS232: 10 m Loewe TV Service Menu: TV application software version: Firmware I2CUART version: Loewe T System data V2.2.x or higher V3.1.x or higher

Configuration M203 Loewe TV SL1xx / SL2xx / SL3xx The designation SLxx describes the chassis electronics of the Loewe television and not the television type. The chassis version can be checked in the Loewe television Service menu. Between M203 and Loewe TV a special cable is required, which can be ordered at the Revox service department. Typ:RJ12 SubD9 Max. cable length: 5 m i Audio connection M219 For the analogue audio connection (stereo l/r) between the sideroom amplifier M219 and the Loewe TV with SL chassis a special cubic adapter from Loewe is needed, which can be ordered at Loewe accessories shop. 1 software packet V3.0.41 or higher is required 16

M203 Configuration Changing the Loewe IR code at the television In order to avoid IR conflicts between the Loewe television and the Revox system, the system address at the Loewe television and the remote control must be changed. The reason for this is as follows: Both Revox and Loewe use an RC5 code with the system address 00 for the television. For this reason, both systems will react to some of each other s commands. This IR conflict can be solved if the system address 02 is selected for the Loewe television, instead of the 00. The system address is changed in the following way: At the Loewe television (board operating element): Press the M button briefly Press the - button briefly Then, at the Loewe Assist 1 remote control: press the MENU button within 1 second Now, the service menu should be visible. Select the sub-menu Other adjustments from this menu. Select the menu RC subsystem from the Other adjustments menu. The factory setting for the RC subsystem menu is to set the system address to 00. Now set this to 02. The Loewe TV now reacts to the system address 02 as well as to the originally set 00. 17

Configuration M203 Changing the Loewe IR code at the remote control The remote control must also be set to the system address 02. This is done as follows: Hold the Mute button together with the 2 button pressed, until the red LED under the mute button starts to flash, after about 3 seconds. The IR code is now set to the system address 02. If the system address 02 is already used for another device, the address 01 or 08 can be used instead (see light-coloured marking). In such a case, the system address of the Loewe television must also be set to 01 or 08 accordingly. Address 00 is the factory setting. Sound switching with SCART connection between M51 and Loewe television Sound switching for dual-channel transmissions is only possible at the Loewe television s audio output (Cinch socket), not at the SCART output. This means that if the Loewe television is connected with the M51 using a SCART cable, Eurosport, for example, can be heard in parallel in German through the lefthand channel and in English through the righthand channel. That cannot be changed. Using a special SCART cable, available from Revox under the Part no.: 54 429 110, the channel switching can be used correctly again. In this case, the lefthand and righthand sound channels are disconnected and supplied through the external audio output. Please refer to the graphic. Loewe TV outlet: Audio Out 18 M51 outlet: DVD-SCART

M203 Configuration Setup #2 AV Assignment Function: AV Assignment Display: Source Connection: RS232 M219: Yes Unknown audio sources "Sources unknown" can still be present during the initial configuration, caused by the swap or the de-installation of modules. 1. Selecting audio source To start with, select the M51 / M219 audio source that later should activate a particular video input on the Loewe television/ HDMI Switcher, using the Source softkey. Following switch-on, it can take a few seconds until the M203 interface has identified all the M51 / M219 sources and until the Source Unknown" message disappears. Any remaining unknown sources should be deleted by pressing the Disable softkey twice and then pressing the Delete soft-key. If too many unknown sources are present, we recommend completely resetting the M203 interface by pressing the Disable softkey for several seconds, until Page #1 automatically appears. Using the Source+ and Sourcesoftkeys, you can step forwards and backwards respectively, through a loop of audio inputs, which are currently available on the M51 / M219. If the name of an audio source has been changed, the modified name also appears in the list. An Unknown Source must be deleted manually. You will find more information about this in the previous section. 19

Configuration M203 Intelligent Audio Sources The M203 differentiates between 3 type of audio sources: a. Permanent sources b. Semi-intelligent sources c. Intelligent sources a. Permanent sources In the case of permanent audio sources, including for example the Tuner source, the television is switched on immediately with the corresponding video input that was assigned to it on Setup page #5. Manual switch-on or switch-off through the remote control is not possible. b. Semi-intelligent sources In the case of semi-intelligent sources, you can define through the remote control, whether the television should be switched on with the previously defined video input or not. Such sources have respectively TV ON and TV OFF function keys in the remote control menu. The semi-intelligent sources, such as the M37 Music Server, store the last selected state. If, for example, the video input from the Server was activated at the television using the remote control, the television is automatically activated next time this source is selected. c. Intelligent sources In the case of intelligent sources, it is a question of sources, which, dependant on setting or medium, can transmit a video signal to accompany the audio signal. An example of an intelligent source is the DVD/CD M51 source. If there is a music CD on the M51 drive, the television is not switched on because in this case, no video is required. If, on the other hand, a DVD is identified, the television is switched on. Source Switch on Yes/No DVD/CD: CD Switch on: No o DVD Switch on: Yes SAT: Radio TV Switch on: No o Switch on: Yes 20

M203 Configuration Setup #2 AV Assignment 2. Assigning video inputs In the second step, a video input from the television / HDMI Switcher is assigned to the selected M51/ M219 audio source, using the Input softkey. Using these softkeys, you can step through a loop of video inputs that are available to the television. The following display appears, if a video input is called by one or more audio sources: Assignment example As the televisions that can be selected from have different video inputs, only those video inputs that the corresponding TV device has, are actually displayed. The softkey Store appears as confirmation each time the Input is changed. Press Store if you want to save your changes. Otherwise the original setting is retained. This example shows you that, as well as the currently displayed audio source (DVD), a further audio source has also been assigned to this video input. Using the Source softkeys, you can search for the audio source that also calls this video input. Several audio sources are always required if, for example, the M300/M301 Video switch is used, which bundles several video sources together to one video input on the television. 21

Configuration M203 Setup #2 Disable Disable assignment Using the Disable function, you can undo or disable the assignment of an audio source to a video input. Reset assignment If you want to return the settings in Setup #2 menu to the factory settings, simply press and hold the Disable softkey until the Setup- #1 page appears again. To do this, select the required audio input using the Source ± softkeys and then press the Disable softkey. The Store softkey then appears that you need to press to confirm your change. This resets all input assignments and restores the factory settings. If you don t press Store, the original setting is retained. 22

M203 Appendix Guarantee The guarantee period is 24 months from the date of purchase. Your dealer should be your first contact if you need service. If he can't give you the help you need, send your M203 interface carriage free and without any accessories to your national Sales Office. Please supply a complete description of the problem and a full return postal address. Included in delivery M203 Interface M-Link cable ( 2 m ) Serial PC cable (1:1 - length 3 m) (Plug-Socket) RS232 Crossover adapter Gender adapter Accessories (Installation) Technical data IR-LINK: + Positive voltage 10-20V (DC) IN IR signal - Ground (GND) Dimensions: 113 x 25 x 50 mm (WxHxD) Weight: 150 g Power consumption: 35 ma (without IR receiver) Max. cable length: 100 m (M203- M51/ M100/ M219) Max. cable length: 30 m (M203 - IR receiver) Product subject to technical modifications. 23

Configuration M203 M203 Interface Loewe manual 24