SERIES 5570, IMPACT RESISTANT SLIDING GLASS DOOR TO ACHIEVE PROPER ANCHOR EDGE DISTANCE, THE FOLLOWING SHEETS SHOW ANCHOR PATTERNS THAT MUST BE USED WHEN INSTALLING WITH THE FRAME FIN-ADDON. ANCHORS TO BE INSTALLED THROUGH THE MAIN FRAME AND NOT THE FRAME FIN-ADDON. INTERMEDIATE HEAD ANCHORS 25.375" O.C.; SEE SHEETS 2 & 3 FOR QUANTITY/DP, SEE SHEET 6 FOR SPACING 6" B HEAD CLUSTER ANCHORS MIN. O.C.; SEE SHEETS 2 & 3 FOR QUANTITY/DP, SEE SHEET 5 FOR SPACING 6" TABLE A: * MIN. OF 3 THREADS BEYOND THE METAL SUBSTRATE. FOR STEEL STUDS, MIN. FU=45 KSI & MIN. FY=33 KSI. "UNGROUTED CMU" VALUES MAY BE USED FOR GROUTED CMU APPLICATIONS. JAMB ANCHORS 21.6" O.C.; SEE SHEETS 2 & 3 FOR QUANTITY/DP, SEE SHEET 4 FOR SPACING A INTERMEDIATE SILL ANCHORS 25.375" O.C.; SEE SHEETS 2 & 3 FOR QUANTITY/DP, SEE SHEET 6 FOR SPACING C SILL CLUSTER ANCHORS MIN. O.C.; SEE SHEETS 2 & 3 FOR QUANTITY/DP, SEE SHEET 5 FOR SPACING INSTRUCTIONS: 1) KNOWING THE REQUIRED DESIGN PRESSURE OF THE OPENING, THE ANCHOR REQUIREME FOR THE SLIDING GLASS DOORS MAY BE ERMINED FROM DESIGN PRESSURE TABLES 1 OR 2, DEPENDING ON THE REINFORCEMENT LEVEL DESIRED. 2) LOCATE THE SLIDING GLASS DOOR SIZE ON THE TABLE, USING THE FRAME HEIGHT AND THE NOMINAL WIDTH. IF YOUR EXACT SIZE IS NOT SHOWN, ROUND UP TO THE NEXT GREATER LISTED WIDTH AND/OR HEIGHT. 3) CHOOSE WHICH ANCHOR GROUP (A-D) IS MOST APPLICABLE. ANCHORS ARE DEFINED IN TABLE A, THIS SHEET, ALONG WITH THE CORRESPONDING SUBSTRATE, MINIMUM EMBEDMENT AND MINIMUM EDGE DISTANCE. 4) FROM THE DESIGN PRESSURE TABLES (TABLES 1 OR 2), VERIFY THAT THE OPENING'S REQUIRED DESIGN PRESSURE IS MET OR EXCEEDED. USE THE ANCHOR QUANTITIES SHOWN. 5) INSTALL AS PER THE GUIDELINES OF THIS SHEET-SET. GENERAL 1) INSTALLATION SCREWS & FRAME S TO BE SEALED WITH NARROW JOINT SEALANT. 2) DOOR SIZES MUST BE VERIFIED FOR COMPLIANCE WITH EGRESS REQUIREME PER THE IBC, AS APPLICABLE. 3) DRAWINGS DEPICT -GLAZING, HOWEVER INTERIOR-GLAZING MAY BE SUBSTITUTED. GENERAL NOTES 1 OF 9
TABLE 1: ANCHORAGE TYPE PER SUBSTRATE REQUIRED TO ACHIEVE THE DESIGN PRESSURE, USING THE ANCHOR QUANTIES LISTED BELOW. SEE TABLE A, SHEET 1 FOR COMPLETE ANCHOR LIMITATIONS. THE MAXIMUM DP AT THESE ANCHOR QUANTITIES. ADDITIONALLY, THE MAXIMUM POSITIVE DP DUE TO THE SILL HEIGHT MUST ALSO BE CONSIDERED, SEE TABLE B1, THIS SHEET. # OF ANCHORS THROUGH THE HEAD & SILL. (EX: FOR C3+1, 3 ANCHORS CLUSTERED AT MEETING POINT AND 1 ANCHOR REQUIRED AT INTERMEDIATE OF ). TOTAL # OF ANCHORS THROUGH THE JAMB. FOR POCKET CONFIGURATIONS, THE # OF ANCHORS REQUIRED THROUGH THE P-HOOK, PERPENDICULAR TO THE GLASS. TABLE B1: DLO WIDTH = NOM. WIDTH - 8-9/16" DLO HEIGHT = DOOR HEIGHT - 11-1/16" HEIGHT = DOOR HEIGHT - 2-1/2" TABLE 1) IF WATER INFILTRATION RESISTANCE IS REQUIRED,THE LESSER VALUES OF EITHER TABLE 1 AND TABLE B1 ERMINES THE WATER LIMITED (+) DP. 2) IF WATER INFILTRATION RESISTANCE IS NOT REQUIRED, A SILL RISER IS NOT REQUIRED. IF SO, +DP'S SHOWN IN TABLE 1 MAY BE USED. 3) SHEET APPLIES TO 2, 3 AND 4 TRACK CONFIGURATIONS. DP & ANCHOR QUANTITY TABLE 2 OF 9
TABLE 2: ANCHORAGE TYPE PER SUBSTRATE REQUIRED TO ACHIEVE THE DESIGN PRESSURE, USING THE ANCHOR QUANTIES LISTED BELOW. SEE TABLE A, SHEET 1 FOR COMPLETE ANCHOR LIMITATIONS. THE MAXIMUM DP AT THESE ANCHOR QUANTITIES. ADDITIONALLY, THE MAXIMUM POSITIVE DP DUE TO THE SILL HEIGHT MUST ALSO BE CONSIDERED, SEE TABLE B2, THIS SHEET. # OF ANCHORS THROUGH THE HEAD & SILL. (EX: FOR C3+1, 3 ANCHORS CLUSTERED AT MEETING POINT AND 1 ANCHOR REQUIRED AT INTERMEDIATE OF ). TOTAL # OF ANCHORS THROUGH THE JAMB. FOR POCKET CONFIGURATIONS, THE # OF ANCHORS REQUIRED THROUGH THE P-HOOK, PERPENDICULAR TO THE GLASS. TABLE B2: * +/-100.0 PSF FOR ANCHOR GROUPS B, C & D. DLO WIDTH = NOM. WIDTH - 8-9/16" DLO HEIGHT = DOOR HEIGHT - 11-1/16" HEIGHT = DOOR HEIGHT - 2-1/2" TABLE 1) IF WATER INFILTRATION RESISTANCE IS REQUIRED,THE LESSER VALUES OF EITHER TABLE 2 AND TABLE B2 ERMINES THE WATER LIMITED (+) DP. 2) IF WATER INFILTRATION RESISTANCE IS NOT REQUIRED, A SILL RISER IS NOT REQUIRED. IF SO, +DP'S SHOWN IN TABLE 2 MAY BE USED. 3) SHEET APPLIES TO 2, 3 AND 4 TRACK CONFIGURATIONS. DP & ANCHOR QUANTITY TABLE 3 OF 9
NOTES 1) AILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS. 2) REFER TO TABLE A FOR ANCHOR CONSTRAI. 3) SILL ANCHORAGE WITH FIN-ADDON IS UNCHANGED FROM THE BOX FRAME ANCHORAGE..125 1.625.875 FRAME FIN-ADDON 99 ALUMINUM 6063-T6 PART # 19033 EMBEDMENT EDGE DISTANCE SUBSTRATE 99 A 1/ 8 2-TRACK FRAME JAMB ANCHORAGE AIL TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE A, SHEET 1. SUBSTRATE 99 EDGE DISTANCE B TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE A, SHEET 1. EMBEDMENT 1/ 2-TRACK FRAME HEAD ANCHORAGE AIL 1/ EMBEDMENT C EDGE DISTANCE 2-TRACK FRAME SILL ANCHORAGE AIL TYP. ANCHOR TYPE, EMBEDMENT AND EDGE DISTANCE PER SUBSTRATE, SEE TABLE A, SHEET 1. SUBSTRATE JAMB ANCHORS LAYOUT, (PARTIAL VIEW): 21.6" O.C. 21.6" O.C. 2.375" 21.6" O.C. 4.75" FIGURES PERTAIN TO THE FOLLOWING JAMB ANCHOR S: 1) STANDARD ANCHOR S SHOWN. FOR 3 AND 4-TRACK JAMBS, ANCHORS IN THE INTERIOR TRACK MAY BE LOCATED IN THE ADJACENT TRACK AS REQUIRED TO MEET MIN. EDGE DISTANCE CONSTRAI FROM THE INTERIOR. 6" 6" 6" NOA (LM) ANCHOR S A 2-TRACK FRAME JAMB ANCHORS 3-TRACK FRAME JAMB ANCHORS 4-TRACK FRAME JAMB ANCHORS 4 OF 9
HEAD CLUSTER ANCHORS LAYOUT (USES FRAME FIN-ADDON): SILL CLUSTER ANCHORS LAYOUT: FIGURES PERTAIN TO THE FOLLOWING SILL CLUSTER ANCHOR S: 2-TRACK CLUSTER "C3" ANCHOR S 2-TRACK CLUSTER "C5" ANCHOR S 2-TRACK CLUSTER "C3" ANCHOR S 2-TRACK CLUSTER "C5" ANCHOR S 3-TRACK CLUSTER "C3" ANCHOR S 3-TRACK CLUSTER "C5" ANCHOR S 3-TRACK CLUSTER "C3" ANCHOR S 3-TRACK CLUSTER "C5" ANCHOR S 4-TRACK CLUSTER "C3"ANCHOR S 4-TRACK CLUSTER "C5"ANCHOR S 4-TRACK CLUSTER "C3" ANCHOR S 4-TRACK CLUSTER "C5" ANCHOR S 2) TRACK-TO-TRACK DISTANCE IS 2.375": 2.375" FIGURES PERTAIN TO THE FOLLOWING HEAD CLUSTER ANCHOR S: NOA (LM) ANCHOR S B 5 OF 9
HEAD "+" INTERMEDIATE ANCHORS LAYOUT (USES FRAME FIN-ADDON): SILL "+" INTERMEDIATE ANCHORS LAYOUT: "+1" ANCHOR "+2" ANCHOR S "+3" ANCHOR S "+1" ANCHOR "+2" ANCHOR S "+3" ANCHOR S "+1" ANCHOR "+2" ANCHOR S "+3" ANCHOR S "+1" ANCHOR "+2" ANCHOR S "+3" ANCHOR S 4-TRACK INTERMEDIATE "+1" ANCHOR 4-TRACK INTERMEDIATE "+2" ANCHOR S 4-TRACK INTERMEDIATE "+3" ANCHOR S 4-TRACK INTERMEDIATE "+1" ANCHOR 4-TRACK INTERMEDIATE "+2" ANCHOR S 4-TRACK INTERMEDIATE "+3" ANCHOR S FIGURES PERTAIN TO THE FOLLOWING SILL INTERMEDIATE ANCHOR S: FIGURES PERTAIN TO THE FOLLOWING HEAD INTERMEDIATE ANCHOR S: 2) TRACK-TO-TRACK DISTANCE IS 2.375": 2.375" ANCHOR S C 6 OF 9
HEAD 90 CORNER CLUSTER ANCHORS LAYOUT (USES FRAME FIN-ADDON): SILL 90 CORNER CLUSTER ANCHORS LAYOUT: FIGURES PERTAIN TO THE FOLLOWING 90 CORNER SILL ANCHOR S: 90 2-TRACK 90 CORNER "C ANCHOR S 2-TRACK 90 CORNER 2-TRACK 90 CORNER "C ANCHOR S 2-TRACK 90 CORNER 3-TRACK 90 CORNER "C ANCHOR S 3-TRACK 90 CORNER 3-TRACK 90 CORNER "C ANCHOR S 3-TRACK 90 CORNER 90 4-TRACK 90 CORNER "C ANCHOR S FIGURES PERTAIN TO THE FOLLOWING 90 CORNER HEAD ANCHOR S: 4-TRACK 90 CORNER 2) AILS DEPICT ANCHOR QUANTITY AND SPACING, AND WOULD BE SIMILAR FOR OUTSIDE (SHOWN) AND INSIDE CORNER CONFIGURATIONS. 4-TRACK 90 CORNER "C ANCHOR S 4-TRACK 90 CORNER ANCHOR S D 3) TRACK-TO-TRACK DISTANCE IS 2.375": 2.375" 7 OF 9
HEAD 135 CORNER CLUSTER ANCHORS LAYOUT (USES FRAME FIN-ADDON): SILL 135 CORNER CLUSTER ANCHORS LAYOUT: FIGURES PERTAIN TO THE FOLLOWING 135 CORNER SILL ANCHOR S: 135 2-TRACK 135 CORNER "C ANCHOR S 2-TRACK 135 CORNER 2-TRACK 135 CORNER "C ANCHOR S 2-TRACK 135 CORNER 3-TRACK 135 CORNER "C ANCHOR S 3-TRACK 135 CORNER 3-TRACK 135 CORNER "C ANCHOR S 3-TRACK 135 CORNER 4-TRACK 135 CORNER "C ANCHOR S 4-TRACK 135 CORNER 4-TRACK 135 CORNER "C ANCHOR S 4-TRACK 135 CORNER FIGURES PERTAIN TO THE FOLLOWING 135 CORNER HEAD ANCHOR S: 135 2) AILS DEPICT ANCHOR QUANTITY AND SPACING, AND WOULD BE SIMILAR FOR OUTSIDE (SHOWN) AND INSIDE CORNER CONFIGURATIONS. ANCHOR S E 3) TRACK-TO-TRACK DISTANCE IS 2.375": 2.375" 8 OF 9
HEAD ANCHORS LAYOUT @ OR ASTRAGAL (USES FRAME FIN-ADDON): SILL ANCHORS LAYOUT @ OR ASTRAGAL: FIGURES PERTAIN TO THE FOLLOWING D SILL ANCHOR S: 2" 2" 2-TRACK "C ANCHOR S 2-TRACK 2-TRACK "C ANCHOR S 2-TRACK 3-TRACK "C ANCHOR S 3-TRACK 3-TRACK "C ANCHOR S 3-TRACK 4.75" 4-TRACK "C ANCHOR S 4-TRACK 4-TRACK 4-TRACK "C ANCHOR S FIGURES PERTAIN TO THE FOLLOWING D HEAD ANCHOR S: 2) TRACK-TO-TRACK DISTANCE IS 2.375": 2.375" ANCHOR S F 9 OF 9