SB-3691 2x1 HDMI PiP/PoP Selector Switch Scaler INSTRUCTION MANUAL IMPORTANT WARRANTY INFORMATION. If you remove the HDMI screw posts, you must use the provided HDMI Locking Post replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws without installing the HDMI Locking Post replacement screws will void your warranty.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture. 5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth. 6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance. 7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced. 8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated. 9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty. 10. Turn power off and disconnect unit from AC current before making connections. 11. Never hold a power switch in the ON position. 12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices. 13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically blown free of foreign dust and matter. 14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside. 15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices. 16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. 17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time. 18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. 19. Service Information Equipment should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment. C. The equipment has been exposed to rain. D. The equipment does not appear to operate normally, or exhibits a marked change in performance. E. The equipment has been dropped, or the enclosure damaged. THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
TABLE OF CONTENTS MultiVideo Digital Converter Series Thank you for purchasing the SB-3691 2x1 HDMI PiP/PoP Select switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use the selector switcher. CONTENTS INTRODUCTION & CONTENTS...1 FEATURES & SPECIFICATIONS...2 FRONT PANEL...3 BACK PANEL...7 REMOTE CONTROL...8 RS-232 PROTOCOL...10 TYPICAL HOOK-UP & APPLICATION...11 HDMI INPUT & OUTPUT RESOLUTIONS...12 INTRODUCTION The SB-3691 is a professional 2x1 HDMI PiP PoP Selector Scaler Switch in 1080p. Supporting (2) HDMI Inputs and (1) HDMI Output with Picture in Picture (PiP) and Picture of Picture (PoP) features that can be easily configured and controlled. The PiP and PoP functions are only available in 1080p; any other resolution will disable the PiP/PoP ability. Supports video resolutions up to 1080p with a signal bandwidth of 165MHz and a data rate up to 4.95Gbps with no signal degradation. The SB-3691 is HDMI 1.3 and HDCP 1.2 compliant, with CE and FCC certifications. Zoom management can be selected between (5) levels. Input resolutions can be scaled up to 1080p or down to 480p. Supports menu for controlling brightness, contrast and saturation. Control is provided via front panel buttons, RS-232 or wireless IR remote control (included). PACKAGE CONTENTS Check that you have the following components; SB-3691 Select Switcher CD Contents: This manual, Windows GUI RS-232 V.3691.3.0.0 Protocol Instructions Master wireless IR Remote Control (SW-3691) Wall mount bracket (Part # 1INCH-130MM) HDMI Locking Post Replacement Screws Users Guide Power Supply: Input: Universal Type switch 100~240VAC, 50/60Hz / Output: 12VDC 1.25A LOOK A PUPPY!! NOW READ THIS!! IMPORTANT WARRANTY INFORMATION. If you remove the HDMI screw posts, you must use the provided HDMI Locking Post replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws without installing the HDMI Locking Post replacement screws will void your warranty. SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. Never spill liquid of any kind on or into this product. Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. Do not attach the power supply cabling to building surfaces. Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use. We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document. We reserve the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual, or otherwise without express written permission and consent. Copyright 2018. All Rights Reserved. Version 2.9 FEB 2018 3691-20170223-010 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. 1
FEATURES & SPECIFICATIONS FEATURES (2) HDMI Inputs and (1) HDMI Output Scaler Switch Box Supports Picture in Picture (PiP) and Picture of Picture (PoP) in 1080p. Any other resolution will disable the PiP/PoP ability Link speeds up to 4.95Gbps (link clock rate of 165MHz), HDMI 1.3 and HDCP 1.2 compliant Digital video TMDS formats resolutions up to 1080p with Deep color 36bit Supports (2) HDMI (480i/p to 1080p) Inputs Outputs supports: (1) HDMI 1080p-60Hz (1) S/PDIF (1) Stereo audio (AR/AL), Audio output supports PCM 2ch Zoom management can be selected between (5) levels (16) Control Buttons: SW1/ SW2/ PiP/ PoP/ A/ B/ MENU/ ENTER/ RESOLUTION/LOCK/ RESET/ ZOOM/ Up/ Down/ Right/ Left Menu control for color, brightness, contrast and saturation Scaler Supported: Scaling down to 480p and up to 1080p HDMI cable distance for 1080p-60Hz up to 98 feet (30M) Provided IR remote control - Frequency (38KHz) Various User Interface Control: Front panel push buttons IR wireless remote control RS-232 interface control driver for 2000/XP/WIN7-32/WIN7-64/WIN8 Power Supply: Input: Universal Type switch 100~240VAC, 50/60Hz / Output: 12VDC 1.25A SPECIFICATIONS Type of Switcher: (2) HDMI Inputs and (1) HDMI Output Selector Switch Scaler Box HDMI Support: HDMI 1080p@60Hz, H36-bit Deep color HDCP / HDMI Support: HDCP 1.2 Compliant, HDMI 1.3 version Video Bandwidth: Double Data Rates: 165Mhz, Total 4.95Gbps bandwidth Digital Video Support: HD: 480i/ 480p/ 720p and up to 1080i/p PiP/PoP Zoom Function: Selected between 5 levels Input: (2) HDMI (HDMI or DVI digital source) Output: (1) HDMI (To Destination) Switch Controls: Select & Function buttons on front panel IR Remote Control (switch control) RS-232 Scaling Mode: Scaler down to 480p and up to 1080p HDMI Signal Booster: Distance for 1080p cable up to 98 feet (30M) Standby Status: SBY LED indicate STANDBY status Infrared Frequency: 38Khz Firmware Update: Firmware update via RS-232 HDMI I/O Connector: HDMI Type A - SMD 19pin female type Temperature: Operating Temperature 32 F - 100 F (0 C - 32 C) Wall Mount: 1 inch High Wall Mount pairs ( P/N: WM-1INCH-80mm) Dimensions (LxWxH): 6.69 x 5.71 x 1.5 in (170x145x38mm) Power Supply: Input: Universal Type switch 100~240VAC, 50/60Hz / Output: 12VDC 1.25A Safety Approvals: CE, FCC, REACH Weight: 1.5 lb/0.677 Kgs (Unit only) / 3.1 lb/ 1.4 Kgs (Net) As product improvements are continuous, specifications are subject to change and without notice. 2
FRONT PANEL FRONT PANEL 1. IR SENSOR: The IR sensor receives IR commands from the supplied remote control or third party IR emitter. 2. SW1 BUTTON: SOURCE (1) SELECT BUTTON: Source input #1 select button is provided for HDMI source #1 selection. 3. SW2 BUTTON: SOURCE (2) SELECT BUTTON: Source input #2 select button is provided for HDMI source #2 selection. 4. PiP BUTTON: PiP button is provided for Source #1 (A) & Source #2 (B) Picture in Picture function. 5. PoP BUTTON: PoP button is provided for Source #1 (A) & Source #2 (B) Picture of Picture function. 6. A BUTTON: A button is provided for Source #1 (A) instead of Source #2 (B) picture on screen. 7. B BUTTON: B button is provided for Source #1 (B) instead of Source #2 (A) picture on screen. 8. ENTER BUTTON: Press ENTER to confirm entries. 9. MENU BUTTON: Press MENU button to open the On-Screen display interface. To adjust the color CONTRAST S0...M128...E256. Press the LEFT or RIGHT button to do the adjustment and ENTER to change the volume. To adjust the PiP-BORDER. Press the LEFT or RIGHT button to Enable and Disable the border line. To adjust the AUDIO-SWAP. Press the LEFT or RIGHT button to select the SW-1, SW-2, MASTER and MASTER-SWAP. Press the ENTER button to confirm entries or press again to exit the Menu. 3
FRONT PANEL - I/O SELECT BUTTONS FRONT PANEL 4. FUNCTION KEY : PIP (PICTURE IN PICTURE): A/B button (A and B position) To enable the PiP option on a specific Output, perform the following steps: - Press the PiP button. The screen will return to PiP mode status. - Press the PiP button again, to cycle thru the PiP (5) modes. - Center press the ZOOM button repeatedly to cycle thru, the PiP picture will reduce screen size from 1 thru 5 levels. - Center press the UP or DOWN button to select the PiP picture, increase or reduce screen size from 1 thru 8 levels. - Press the A or B button, to setup the A, B position. (the button will illuminate). PIP A, B POSITION TABLE: Type-1: Position A, B Source #1/Source #2 Type-2: Position B, A Source #2/Source #1 The new configuration will be stored. 4
FRONT PANEL - I/O SELECT BUTTONS FRONT PANEL 5. FUNCTION KEY : POP (PICTURE OF PICTURE): A/B button (A and B position) To enable the PoP option on a specific Output, perform the following steps. - Press the PoP button. The screen will return to PoP mode status. - Press the PoP button again, to cycle thru the PoP (2) modes. - Press the ZOOM button repeatedly, the PoP picture will cycle thru the Zoom 1 to Zoom 5 levels. - Press the A or B button, to setup the A,B position (the button will illuminate). PIP A, B POSITION TABLE: Type-1: Position A, B Source #1/Source #2 Type-2: Position B, A Source #2/Source #1 The new configuration will be stored. 5
FRONT PANEL FRONT PANEL 10. LEFT BUTTON: Press the LEFT button to move left on the screen when the SCN-ADJ function is enabled. 11. UP BUTTON: Press the UP button to move up on the screen when the SCN-ADJ function is enabled. 12. DOWN BUTTON: Press the DOWN button to move down on the screen when the SCN-ADJ function is enabled. 13. RIGHT BUTTON: Press the RIGHT button to move right on the screen when the SCN-ADJ function is enabled. 14. SELECT OUTPUT RESOLUTION BUTTON: Press the RES Resolution s button to select the embedded output resolutions. 15. RESET BUTTON: Press the RESET button, the system returns to factory defaults. 16. LOCK BUTTON: - Press and hold LOCK button for 3 seconds to lockout the front panel. - Press and hold LOCK button for 3 seconds to enable the front panel. 17. ZOOM BUTTON: Press the ZOOM button to zoom out on the screen when the SCN-ADJ function is enabled. 18. SBY BUTTON: Standby LED turns on when the unit is powered off for STANDBY status. 19. POWER BUTTON: Press the POWER button to turn on the unit or press it again to turn off the unit. 6
BACK PANEL BACK PANEL 1. DC POWER INLET: The converter suits a DC power plug-pack input connector. Please ensure the plug-pack used is of an approved type and of correct current, voltage output, and connector polarity. DV 12 Volt, power supply 1.25A. POWER JACK: DC Jack - Inner OD Ø 2.1mm (+) Outside OD Ø 5.5mm (GND) Power Input: 12VDC, 1.25A 2. RS-232 CONNECTION: Connects a serial cable to the RS-232 port for control of the converter or update the firmware via a computer. * Firmware procedure is included in a separate document and utilizes the pin marked P. This port also supports Firmware updates. REMOTE CONTROL PORT: Terminal Block female socket (pitch=3.5mm) 3. HDMI INPUT-1: Connects a HDMI signal to the HDMI female connector, which supports HDMI digital video and audio to the HDMI display. If you remove the HDMI screw posts, you must use the provided HDMI Locking Post replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws without installing the HDMI Locking Post replacement screws will void your warranty. HDMI digital video and audio female connector 4. HDMI INPUT-2: Connects a HDMI signal to the HDMI female connector, which supports HDMI digital video and audio to the HDMI display. If you remove the HDMI screw posts, you must use the provided HDMI Locking Post replacement screws to keep the internal HDMI jack secure. Removing the HDMI screws without installing the HDMI Locking Post replacement screws will void your warranty. HDMI digital video and audio female connector 5. HDMI OUTPUT: Connects a HDMI digital video/audio signal link direct to the female HDMI connector, which supports HDMI digital video/audio and DVI digital video sources. HDMI female connector Note: With proper adapters, the scaler can be used with DVI digital video signals. 6. SPDIF OUTPUT: Connects the digital audio output from the digital audio source. Female RCA connector 7. AUDIO OUTPUT: Connects the stereo audio output port of your source audio device to the stereo audio (AR/AL) inputs. Stereo Audio (AR/AL) via (1) OD3.5mm jack connector 7
REMOTE CONTROL & REMOTE PROTOCOL COMMANDS BEFORE MAKING ANY CONNECTIONS OBSERVE THE FOLLOWING: Ensure the main voltage supply matches the label on the supplied plug-pack (+/-10%). Ensure that the power switch is OFF. Ensure that all system grounds (earth) are connected to a common point. Avoid powering equipment within a system from multiple power sources that may be separated by large distances. Connect all audio video sources and destination equipment. Power up all source and destination audio-visual sources. To yield video/audio to an output, select the input source by using the front panel input buttons, the supplied IR remote control, or through the RS-232 serial communication port. Upon power up the switcher will return to its last used setting before being powered down. REMOTE CONTROL IR REMOTE CONTROL KEY : 1. / 2. POWER ON AND OFF: Turns on or off the scaler. 3. SW-1: Selects HDMI #1 source signal. 4. PIP: Picture in Picture (PiP) function. 5. A : Change to the A via others source signal. 6. SW-2: Select HDMI #2 source signal. 7. POP: Picture of Picture (PoP) function. 8. B : Changes to the B via others source. 9. MENU: Open & setup OSD options. 10. / 11. / 12. / 13. ARROW KEYS: Move up, down, left or right between the OSD options. Uses left and right keys to adjust the value of a parameter. Uses down key to enter the next layer of options and up key to move back. 14. ENTER: Confirms your selection/enter the next layer of OSD options 15. HDMI OUTPUT RESOLUTION: 480p 16. HDMI OUTPUT RESOLUTION: 576p 17. HDMI OUTPUT RESOLUTION: 720p 18. HDMI OUTPUT RESOLUTION: 1080i 19. HDMI OUTPUT RESOLUTION: 1080p 20. ZOOM: Opens SCN-ADJ zoom out function. 21. RESET: Opens SCN-ADJ to RESET SCN-ADJ configuration. 22. LOCK: - Press and hold LOCK button for three seconds lockout the front panel. - Press and hold LOCK button for three seconds to enable the front panel. 8
IR DATA CODE LIST IR REMOTE CUSTOM AND DATA CODES (NEC Standard) HOW TO SETUP IR CODES : CUSTOM CODE : 5A69 POWER ON: 5A69 A15E POWER OFF: 5A69 A25D MENU: 5A69 A55A ENTER: 5A69 AB54 FUNCTION KEYS: RESOLUTIONS: SCN-ADJ.: (SW1) SOURCE-1 5A69 956A 480P 5A69 F10E ENTER 5A69 AB54 (SW2) SOURCE-2 5A69 9F60 576P 5A69 F708 UP 5A69 A758 PIP 5A69 EE11 720P 5A69 F40B RIGHT 5A69 AA55 POP 5A69 EF10 1080I 5A69 F50A LEFT 5A69 A956 SELECT BUTTONS: 1080P 5A69 F609 DOWN 5A69 A857 A 5A69 EC13 ZOOM 5A69 AF50 B 5A69 EC12 RESET 5A69 9B64 LOCK 5A69 B54A Example 1: Select SW-1 source Input to Output The IR Data Code: 5A69 956A Example 2: PiP PiP ZOOM ENTER to confirm selection. The IR Data Code: 5A69 EE11 5A69 EE11 5A69 AF50 5A69 AB54 9
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM. VERSION COMPATIBLE V.3691.3.0.0 For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual. Example of the commanded string to select Inputs: FUNCTION COMMAND COMMAND VARIABLES Select source Source xxx; xxx = Input Channel (001~002) (001=SW-1, 002=SW-2) COMMAND EXAMPLE RESPONSE DESCRIPTION Source 001; Source 001#ok; Select source number 1 SB Device RS-232 CONFIGURATION RS-232 cable is a straight thru cable and not null-modem Definition Pin Pin Definition 1 1 DCD TX 2 2 RX RX 3 3 TX 4 4 DTR GND 5 5 GND 6 6 DSR 7 7 RTS 8 8 CTS 9 9 RI PC RS-232 Pin Diagram RS-232 Pin Diagram This port also for Firmware update RS-232 control Terminal Block female socket (pitch=3.5mm) RS-232 SERIAL INTERFACE PROTOCOL COMMANDS The Shinybow switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system. The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1. When the unit recognizes a complete command it will perform the requested action - there is no delimiter character required. 10
TYPICAL APPLICATION INSTALLING DIAGRAM Sample Connection: 1. Using RS-232 commands to control the Selector Switcher (SB-3691) for PiP-PoP function via PC. 2. Input supports: (2) HDMI source devices. 3. Output support: (1) HDMI to displays. NOTE: 1. TV Output Supports: Switch PiP function PoP function 2. Control switch via a PC RS-232 Application RS-232 series controls the Selector Switcher. 11
HDMI INPUT & OUTPUT RESOLUTIONS HDMI (PC) INPUT RESOLUTIONS 640x480@60Hz 1280x768@60Hz 640x480@75Hz 1280x800@60Hz 800x600@60Hz 1280x800@75Hz 800x600@75Hz 1280x960@60Hz 848x480@75Hz 1280x1024@60Hz 852x480@60Hz 1280x1024@75Hz 1024x768@60Hz 1366x768@60Hz 1024x768@75Hz 1365x1024@60Hz 1152x864@75Hz 1400x788@60Hz 1280x720@60Hz 1400x1050@60Hz 1400x1050@75Hz 1440x900@60Hz 1440x900@75Hz 1600x1200@60Hz 1600x1200@75Hz 1680x1050@60Hz 1680x1050@75Hz 1792x1344@60Hz 1792x1344@75Hz 1856x1392@60Hz 1856x1392@75Hz 1152x864@75Hz 1920x1080@60Hz 1920x1200@75Hz 832x6248@75Hz 1152x870@75Hz All of the above PC Input Resolutions work with the following HDMI Output Resolutions. VGA 640x480 SVGA 800x600 480p 720x480 576p 720x576 720p 1080x720 1080i 1920x1080 1080p 1920x1080 HDMI INPUT RESOLUTIONS 480i 720p 480p 1080i 576i 1080p 576p All of the above HDMI Input Resolutions work with the following HDMI Output Resolutions. VGA 640x480 SVGA 800x600 480p 720x480 576p 720x576 720p 1080x720 1080i 1920x1080 1080p 1920x1080 12
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE PRODUCT ). By using or installing the product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the product and return the product to SHINYBOWUSA, Inc. at the return address set forth on the product s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime, without notice to you. RESTRICTIONS ON USE OF THE PRODUCT It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the product. You are authorized to use the product solely in connection with such instructions. Any use of the product not in accordance with such instructions shall void any warranty pertaining to the product. Any and all damages that may occur in the use of the product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage. The product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the product are licensed to you by SHINYBOWUSA, Inc. and/or its affiliates, including any manufacturers or distributors of the product (collectively, SHINYBOWUSA ) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the product. The product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only. SHINYBOWUSA does not transfer either the title or the intellectual property rights to the product and SHINYBOWUSA retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the product, and you may not copy or use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA. The functionality and usability of the product is controlled by SHINYBOWUSA, Inc. from its offices within the State of Texas, United States of America. SHINYBOWUSA makes no representation that materials pertaining to the product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the product may be subject to U.S. export controls. DISCLAIMERS AND LIMITATION OF LIABILITY SHINYBOWUSA may change or modify the product at any time, from time to time. THE PRODUCT IS PROVIDED AS IS AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the product and, therefore, such information or statements should not be relied upon as being current as of the date you use the product. Moreover, any portion of the materials pertaining to the product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the product. TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY SHINYBOWUSA. UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL SHINYBOWUSA S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT. END OF DOCUMENT 13
122 Rose Ln. Suite 303 Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.com