4 TRADE 007 AUDIO 008 VIDEO Tel : 0870 00 00 Fax : 0870 00 00 WEB : www.planetsrs.com 8480 oronation Road Park Royal, London NW0 7QJ video door entry system installation instructions IN008v 0008 Getting started Thank you for choosing SRS. If you are installing this system with one entrance panel continue to step. If however you are installing more than one entrance please follow the instructions (IN4) supplied with the multi entrance relay box. Install the cables Use W08 (BT spec.) twisted paired and RG coaxial cable. See cable layout fig.. Any cable joint is potentially a cause of connection faults, it is therefore prudent to keep junctions to a minimum. For this reason we recommend making connections at the panel (max. telephones) or at ONE point in the riser (usually adjacent to the ). fig. video layout 7n 7 7 Install the video phones The video phones should be connected according to the diagram overleaf. Ignore the dashed wires if additional features are not required. If additional video phones are required to be called simultaneously, please refer to Fig.. fig. 00mm 4 Install the entrance panel Please refer to the instructions (IN4000) supplied with the door entry panel. Operation The video door entry system functions as follows. Upon pressing one of the external buttons the corresponding video phone sounds (only when on hook), the screen will light and display the image from the camera. When the called phone handset is picked up, contact is established and conversation may take place. In order to operate the electric lock the push button marked by a key symbol should be fully depressed. Two other buttons (AN70) are provided for auxiliary use. The picture will stay lit for a preset period ( seconds to minutes) adjustable at the 008 PSU. 007 functions The 007 unit (PSU) has built in lock release timer (with relay output), v ac, v dc, and tone outputs. When the lock release button on the phone is pressed, terminal and (at the phone) are shorted, causing the lock release timer to start which in turn changes the state of the relay. The time can be adjusted between 40 seconds (approx.). The v ac (A) and v dc () terminals may be used to power lock releases up to 0. Amps. ac/dc = number of cores n = number of phones = RG oaxial cable If the installation is for a single apartment (with monitor), or a block of apartments on a single riser (with monitor per apartment) AN00 video distributor is not necessary. However for all other installations it is recommended that the distributor is fitted. See fig. 4. AN70 & AN770S (AN70) and slides into the side of the monitor (AN770S) V V R R Three monitors may be called simultaneously. For simultaneous call add local (AN48S) for each additional monitor. W08 fig. calling more than video monitor M AN48S Local PSU From previous video monitor Alternative diagrams & data sheets are available. all 0870 00 00 or visit www.planetsrs.com. D ME entrance basic system diagram over leaf D ME entrance system with video phones (simultaneous call) D nme entrance system (without Trades button) D nmed entrance system (with Trades button) diagram over leaf D nme entrance system (without Trades button) D nmne multi entrance system (without Trades button) E requirements This product was tested for compliance with E directive 8//EE with the panel connected to Earth. Always ensure that external metal parts are independently connected to mains protective earth to avoid electrical shock hazard. dio Door Entry Systems Video Door Entry Systems Keypads Access ontrol Systems Electric Locking & Accessories SRS Wholesale Limited registered in England No: 4 T No: 4
R e m e m b e r Always fit the lock supressor supplied, SRS TZ. This device must be connect ed to a l l electric locks and electric releases. Fit directly across the lock ter m i n a l s. Trouble shooting The first rule of trouble shooting is to make your system as simple as possible. ie. remove any nonessential conn e c t i o n s. No picture (the monitor lights up) a heck for V at the camera b heck video signal c heck correct connection of video distributor if used No picture (monitor won t light up) a In order for the monitor to light it must be called and get 8V from the PSU. b heck for a call tone at the monitor c heck for 8V on R (ve) & R (ve), both at the PSU and more i m p o r t a n t l y, at the monitor. Poor picture a Failure to fit end of line resistors. For systems w i t h o u t video distributor (AN00) ONE resistor should be fitted across V & V of the last monit o r. For systems w i t h video distributor O N E resistor should be fitted across V & V of the last monitor for each output ( in total if one distributor fitt e d ). b Low power to the video monitor. heck for 8 volts between R and R (ve) at the monitor when the monitor has been called. If the voltage is less than volts then picture quality will be poor. In this case check for overall load (max amp) and cross sectional area of the R & R wires. High pitched screech: a Excessive amplification (volume requires adjustment) b Unhooked handset hanging down & facing wall c Short circuit on wires & d Incorrect cable used e Poor alignment of microphone to hole in front plate. No speech a heck for short circuits and/or breaks on wires &. b heck V dc at speaker unit Lock release will not trigger a heck lock connections b Remove cable(s) from at the 007 (PSU). Trigger input with egress button. If this corrects the fault, check wire to telephone. c With a meter check lock relay output is changing state. fig. 4 connection of video distributor telephone (AN70) and slides (AN770S) telephone (AN70) and slides (AN770S) telephone (AN70) and slides (AN770S) telephone (AN70) and slides (AN770S) V V V4 Out IN Video to monitor Video to monitor Video to monitor Video to monitor 4 Video OUT To IN of next AN00 (or fit resistor across OUT and ) Video IN V V R R V V R R V V R R V V R R SRS Video amera 008 VIDEO
D M E Video Diagram Monitors Entrances One entrance video door entry system calling monitor..04 AN70 & AN770S (AN70) and slides into the side of the monitor (AN770S) V V R R W08 Installation Notes : able requirements : Maximum recommended overall distance for W08 BT spec. twisted paired cable run is 00 metres. For longer cable runs up to 0 metres the cables R & R should be.mm dia. interference. The action of making a call will draw current from at the 008. The timed output R (8vdc) is started. The monitor can be lit only whilst the timer is running and a call has been made. Video Telephone Three monitors may be called simultaneously. For simultaneous call add local (AN48S) for each additional monitor, as shown. A video distributor (AN00) is also recommended if an additional monitor is called simultaneously. TWO wires for terminal of the telephone. White / Green & are shown. This is intentional and should be followed for best results. Two push buttons are available for other functions (eg. opening a second lock) marked / & Q/Q. These are both push to make momentary switches. all button 008 VIDEO 008V Video PSU R R Speaker Unit T amera Unit Z 0 A V A fail locked A V fail locked V fail open N/ GND N/ OM v A V A FAIL LOKED illustrated
D nm E D Video Diagram Monitors Entrances Distributor One entrance video door entry system calling n monitors..0 Installation Notes : Video Note Fit resistor at each monitor if using AN00 as shown. AN70 & AN770S (AN70) and slides into the side of the monitor (AN770S) V V R R W08 able requirements : It is recommended that cables are star wired to the video monitors from a central point Maximum recommended overall distance for W08 BT spec. twisted paired cable run is 00 metres. For longer cable runs up to 0 metres the cables R & R should be.mm dia. interference. The action of making a call will draw current from at the 008. The timed output R (8vdc) is started. The monitor can be lit only whilst the timer is running and a call has been made. Video Telephone Three monitors may be called simultaneously. For simultaneous call add local (AN48S) for each additional monitor. AN70 & AN770S (AN70) and slides into the side of the monitor (AN770S) V V R R W08 TWO wires for terminal of the telephone. White / Green & are shown. This is intentional and should be followed for best results. Two push buttons are available for other functions (eg. opening a second lock) marked / & Q/Q. These are both push to make momentary switches. Optional keypad The programmable keypad is an option which when ordered can be built into the panel or supplied as a separate unit. Set the lock time on the keypad for sec. The actual lock operating time is set by the timer on the 007. AN70 & AN770S W08 (AN70) and slides into the side of the monitor (AN770S) V V R R AN00 Video Distributor V RG oax V RG oax all buttons V4 Out IN RG oax RG oax Master Fit resistor across Out & Gnd of last AN00 RG Speaker Unit T amera Unit V A fail A V fail V fail open N/ 008V 07. 07. lock timer relay (40s) V FAIL LOKED illustrated with transil fitted
D M E /04 Video Diagram Monitors Entrances One entrance video door entry system calling monitor keypad..04 Installation Notes : AN70 & AN770S (AN70) and slides into the side of the monitor (AN770S) V V R R W08 W08 able requirements : Maximum recommended overall distance for W08 BT spec. twisted paired cable run is 00 metres. For longer cable runs up to 0 metres the cables R & R should be.mm dia. interference. The action of making a call will draw current from at the 008. The timed output R (8vdc) is started. The monitor can be lit only whilst the timer is running and a call has been made. Video Telephone Three monitors may be called simultaneously. For simultaneous call add local (AN48S) for each additional monitor. Note: If using AN777 telephone in place of AN70. onnect as per AN70 except add the following: onnect terminal to v (007. terminal ) If door monitoring is required. onnect terminal 8 to v (007. terminal ) via a door monitor microswitch. A video distributor (AN00) is also recommended if an additional monitor is called simultaneously. TWO wires for terminal of the telephone. White / Green & are shown. This is intentional and should be followed for best results. Two push buttons are available for other functions (eg. opening a second lock) marked / & Q/Q. These are both push to make momentary switches. Keypad The programmable keypad is an option which when ordered can be built into the panel or supplied as a separate unit. Set the lock time on the keypad (default is secs) all button Speaker Unit 008 VIDEO 008V video all Tone v ac A 0 Volts 0 v dc Intercom 07/ R R Z RG oax & T amera Unit Built in Keypad optional v 0v N Tmlk OM EGR PSU V A fail A V fail V fail open N/ Relay shown for fail locked
D Video Diagram nm E /4 D Monitors Entrances keypad Distributor Two entrance (with Trades button) video door entry system calling n monitors with video distribution..04 To further monitors AN70 & AN770S (AN70) and slides into the side of the monitor (AN770S) V V R R Use W08 cable twisted pairs minimum Installation Notes: Ignore dashed wires if not required. able Requirements interference. W08 is suitable for distances up to 00 metres. For longer cable runs you should increase the dimensions of the cores according to the chart. Wire metres Trm Function 00 00 00 Loudspeaker 0. 0. 0.8 Microphone 0. 0. 0.8 ommon ve 0.8 0.8.0 Lock release 0. 0. 0.8 all tone 0. 0. 0.8 R monitor power (ve).0.. R monitor power (8v).0.. Diameter of conductors mm AN70 & AN770S (AN70) and slides into the side of the monitor (AN770S) V V R R AN00 Video Distributor for 4 monitors V V V4 Out IN Use W08 cable twisted pairs minimum Video to monitor Video to monitor Video to monitor Video to monitor 4 To IN of next AN00 Master White / Green & white / blue TWO wires for terminal of the telephone. White / Green & are shown. This is intentional and should be followed for best results. 4 entrance relay When current is drawn from PS (entrance A or B) the relay will latch to the calling entrance for approx. 0 seconds or the duration of the call (whichever is longer). The other entrance, if calling, will hear an engaged tone. Site the (07) close to the relay (4). Two push buttons are available for other functions (eg. opening a second lock) marked / & Q/Q. These are both push to make momentary switches. / terminal The / terminal is a connection which can be used instead of terminal. If you are experienceing feedback (and you are sure it not a connection problem) then the / terminal is used to half the volume of the telephone earpiece. Use with caution Optional keypad The programmable keypad is an option which when ordered can be built into the panel or supplied as a separate unit. TR TR 4 OM all buttons Trade button if fitted TR TR 4 Brown OM Trade button if fitted all buttons 7 8 4 0 TRADE Speaker Unit T amera Unit Built in Keypad optional v 0v N Tmlk OM EGR Brown / White oax PS V V N V V EA EB 4 entrance relay RELAY 4 entrance relay 0 PS V V N I Brown / White oax Speaker Unit T amera Unit 7 8 4 0 TRADE PSU V A fail A V fail V fail open N/ V A fail A V fail V fail open N/ R R Z 0 A onnection shown V fail locked GND N/ OM onnection shown V fail locked 008V 07. 07. lock timer relay (40s)