STC-TB152USB-AT/AS/BTC/BSC Product Specification Software Trigger USB 2.0 Color / Monochrome SXGA CCD Camera
Safety Precautions CAUTION CAUTION RISK OF RISK ELECTRIC OF ELECTRIC SHOCK SHOCK DO NOT DO OPEN NOT OPEN RISK OF ELECTRIC SHOCK DO NOT OPEN!! CAUTION: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT TO CAUTION: REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE REMOVE COVER (OR BACK). NO USER SERVICEABLE TO REDUCE PARTS THE INSIDE. RISK OF ELECTRIC SHOCK, DO NOT PARTS REMOVE INSIDE. COVER (OR BACK). NO USER SERVICEABLE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. REFER PARTS SERVICING INSIDE. TO QUALIFIED SERVICE PERSONNEL. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead The lightning symbol, flash within with an arrowhead equilateral triangle, symbol, The lightning is within flash intended an to equilateral with arrowhead alert the user triangle, to the is symbol, intended within presence to alert an of uninsulated the equilateral user to the triangle, dangerous presence is intended to alert the user to the voltage of uninsulated within the dangerous product s voltage presence of uninsulated dangerous enclosure within the that product s may be of sufficient voltage within the product s enclosure magnitude that may to be constitute of sufficient a risk of enclosure that may be of sufficient magnitude electric to constitute shock to persons. a risk of magnitude to constitute a risk of electric shock to persons. electric shock to persons. For U.S.A. For U.S.A. Warning: Warning: For U.S.A. This Warning: equipment This equipment generates generates and uses and radio uses frequency radio frequency energy energy and if and if not not installed and used properly, I.e., in strict accordance with the This installed equipment and used generates properly, and uses I.e., in radio strict frequency accordance energy with and theif instruction instruction manual, may cause harmful interference to radio not installed manual, and used may properly, cause harmful I.e., in interference strict accordance to radio with the communications. communications. It has been tested and found to comply with the instruction manual, It has may been cause tested harmful and found interference to comply to radio with the limits limits for a Class A computing device pursuant to Subpart J of Part communications. for a Class A It computing has been tested device and pursuant found to to Subpart comply J with of Part the 15 15 of FCC Rules, which are designed to provide reasonable limits of FCC for Rules, a Class which A computing are designed device to pursuant provide reasonable to Subpart J of Part protection against such interference when operated in a commercial protection 15 of FCC against Rules, such which interference are designed when to provide operated reasonable in a commercial environment. environment. protection against such interference when operated in a commercial environment. For Canada For Canada Warning: For Canada Warning: Warning: This digital apparatus does not exceed the Class A limits for radio This digital noise apparatus emissions does from not digital exceed apparatus the Class set A out limits in the for Radio radio noise This emissions digital apparatus does not exceed the Class A limits for radio Interference from Regulations digital apparatus of the Canadian set out in Department the Radio of Interference noise emissions from digital apparatus set out in the Radio Communications. Regulations of the Canadian Department of Interference Regulations of the Canadian Department of Communications. Communications.!!! The exclamation point within an The equilateral triangle is intended to alert The exclamation exclamation point point within within an an equilateral the user to the presence of important equilateral triangle triangle is is intended intended to to alert alert the operating and maintenance (servicing) the user user to to the the presence of of important operating instructions the literature and and maintenance (servicing) instructions accompanying the appliance. in the the literature accompanying the the appliance. WARNING: WARNING: WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE TO THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT FIRE FIRE OR OR SHOCK HAZARD, DO DO NOT NOT EXPOSE THIS THIS APPLIANCE TO TO RAIN RAIN OR OR MOISTURE. Product Precautions Handle the camera with care. Do not abuse the camera. Avoid striking or shaking it. Improper handling or storage could damage the camera. Do not pull or damage the camera cable. During camera use, do not wrap he unit in any material. This will cause the internal temperature of the unit to increase. Do not expose the camera to moisture, or do not try to operate it in wet areas. Do not operate the camera beyond its temperature, humidity and power source ratings. While the camera is not being used, keep the lens or lens cap on the camera to prevent dust or contamination from getting in the CCD or filter area and scratching or damaging this area. Do not keep the camera under the following conditions: In wet, moist, and high humidity areas Under hot direct sunlight In high temperature areas Near an object that releases a strong magnetic or electric field Areas with strong vibrations Use a soft cloth to clean the camera. Use pressured air spray to clean the surface of the glass. DO not scratch the surface of the glass. Product Specification 2 Rev 1.9
Copyright & Disclaimer Sensor Technologies America, Inc. (DBA Sentech America) believes the contents and specifications of its website, catalog, documentation and ads are correct; however, Sentech America provides no representation or warranty regarding such information or product(s) contained therein. It is requested that Sentech America be given appropriate acknowledgement in any subsequent use of such work by a third party. While every effort has been made to ensure that the details contained in Sentech America s website and all documentation are correct and up-to-date, Sentech America assumes no liability, legal or otherwise for any errors in listings, specifications, part numbers, process, software or model applications. Sentech America reserves the right to change specifications, product descriptions, product quality, pricing and application at any time without prior written or oral notice. Any party using such information assumes all risk for any and all damaged caused to themselves, a third party and/or property by virtue of incorrect information and/or failure of these products. By installing and/or using a Sentech America software development kit or other similar product and/or information obtained from Sentech America s website, catalog, documentation or ads, you hereby accept and understand these stated terms and conditions. Product Specification 3 Rev 1.9
Contents I. Specifications... 5-10 A. Electronic Specifications / Mechanical Specifications / Environmental Specifications... 5-6 1. STC-TC152USB-A / TB152USB-A: Case Type... 5 2. STC-TC152USB-B / TB83USB-B: Board Type... 6 B. Connector Specifications... 7 1. USB Connector... 7 2. Input / Output Connector... 7 3. 5V Power Jack... 7 C. Input / Output Signals Specifications (Board Type)... 8-10 1. Input Signals Specifications... 8 2. Output Signals Specifications... 9-10 II. Dimensions... 11 A. STC-TC152SUSB-AT... 11 B. STC-TC152SUSB-AS... 11 C. STC-TC152SUSB-BTC... 12 D. STC-TC152SUSB-BSC... 12 E. STC-TB152SUSB-AT... 13 F. STC-TB152SUSB-AS... 13 G. STC-TB152SUSB-BTC... 14 H. STC-TB152SUSB-BSC... 14 Product Specification 4 Rev 1.9
I. Specifications A. Electronic Specifications / Mechanical Specifications / Environmental Specifications 1. STC-TC152USB-A/ TB152USB-A: Case Type Product STC-TC152USB-AT STC-TC152USB-AS STC-TB152USB-AT STC-TB152USB-AS Electronic 1/2 Interline SXGA Color Progressive CCD: 1/2 Interline SXGA Monochrome Progressive Specs Imager ICX205AK CCD: ICX205AL Total Picture Elements Active Picture Elements Chip Size 1434 (H) x 1050 (V) 1360 (H) x 1024 (V) 7.60 (H) x 6.20 (V) mm Cell Size 4.65 (H) x 4.65 (V) µm Scanning System Progressive Scanning Methods Full Scanning, 1/1 Partial Scanning, ½ Partial Scanning, ¼ Partial Scanning, Variable Partial Scanning Full Scanning, 1/1 Partial Scanning, ½ Partial Scanning, ¼ Partial Scanning, Variable Partial Scanning, Binning, Binning 1/1 Partial Scanning, Binning ½ Partial Scanning, Binning ¼ Partial Scanning, Binning Variable Partial Scanning Mechanical Specs Environ. Specs Pixel Frequency Maximum Frame Rate Resolution Full Scanning ½ Partial ¼ Partial 36.818 MHz (Normal) / 18.4090 MHz (1/2 clock) / 9.20453 MHz (1/4 clock) 19.26 fps (Normal) / 9.63 fps (1/2 clock) / 4.815 fps (1/4 clock) 38.52 fps (Normal) / 19.26 fps (1/2 clock) / 9.63 fps (1/4 clock) 77.04 fps (Normal) / 38.52 fps (1/2 clock) / 19.26 fps (1/4 clock) 1360 (H) x 1024 (V) (Full Scanning) 1360 (H) x 472 (V) (1/2 Partial Scanning) 1360 (H) x 176 (V) (1/4 Partial Scanning) Minimum Scene Illumination 3.22 Lux at F1.2 0.07 Lux at F1.2 Sync. System Electronic Shutter Gain Gamma White Balance Trigger Mode Input / Output Power Dimensions Lens Mount Tripod Weight Input Voltage Consumption Operational Temperature Storage Temperature Vibration Shock 51 (W) x 51 (H) x 46.1 (D) mm Auto / Manual / One shot (software selectable) Internal Auto / Manual (software selectable) Auto / Manual (software selectable) Manual (software selectable) Free-run / Edge preset trigger / Pulse Width Trigger / Start & Stop Trigger (Software Selectable) USB2.0 High Speed +5 V through USB connector / DC Jack 51 (W) x 51 (H) x 48.8 (D) mm Less than 450 ma C Mount 51 (W) x 51 (H) x 46.1 (D) mm 2 screws on the bottom plate Approximately 145g 0 to 40⁰C -30 to 65⁰C - 51 (W) x 51 (H) x 48.8 (D) mm 20Hz to 200Hz to 20Hz (5min./cycle), acceleration 10G, 3 directions 30 min. each Acceleration 70G, half amplitude 6ms, 3 directions 3 times each Standard Compliancy EMS :EN61000-6-2, EMI :EN61000-6-3 (Class B) RoHS RoHS Compliant Product Specification 5 Rev 1.9
2. STC-TC83USB-BT / TC83USB-BS / TB83USB-BT / TB83USB-BS: Board Type Product STC-TC152USB-BTC STC-TC152USB-BSC STC-TB152USB-BTC STC-TB152USB-BSC Electronic 1/2 Interline SXGA Color Progressive CCD: 1/2 Interline SXGA Monochrome Specs Imager ICX205AK Progressive CCD: ICX205AL Total Picture Elements Active Picture Elements Chip Size 1434 (H) x 1050 (V) 1360 (H) x 1024 (V) 7.6 (H) x 6.20(V) mm Cell Size 4.65 (H) x 4.65 (V) µm Scanning System Progressive Scanning Methods Full Scanning, 1/1 Partial Scanning, ½ Partial Scanning, ¼ Partial Scanning, Variable Partial Scanning Full Scanning, 1/1 Partial Scanning, ½ Partial Scanning, ¼ Partial Scanning, Variable Partial Scanning, Binning, Binning 1/1 Partial Scanning, Binning ½ Partial Scanning, Binning ¼ Partial Scanning, Binning Variable Partial Scanning Mechanical Specs Environ. Specs Pixel Frequency Maximum Frame Rate Resolution Minimum Scene Illumination Sync. System Electronic Shutter Gain Gamma White Balance Trigger Mode Input / Output Power Dimensions Lens Mount Full Scanning ½ Partial ¼ Partial Input Voltage Consumption Interface Connector Weight Operational temperature Storage temperature RoHS 36.818 MHz (Normal) / 18.4090 MHz (1/2 clock) / 9.20453 MHz (1/4 clock) 19.26 fps (Normal) / 9.63 fps (1/2 clock) / 4.815 fps (1/4 clock) 38.52 fps (Normal) / 19.26 fps (1/2 clock) / 9.63 fps (1/4 clock) 77.04 fps (Normal) / 38.52 fps (1/2 clock) / 19.26 fps (1/4 clock) 1360 (H) x 1024 (V) (Full Scanning) 1360 (H) x 472 (V) (1/2 Partial Scanning) 1360 (H) x 176 (V) (1/4 Partial Scanning) 2.7 Lux at F1.2 0.12 Lux at F1.2 Auto / Manual / One shot (software selectable Internal Auto / Manual (software selectable) Auto / Manual (software selectable) Manual (software selectable) Free-run / Edge preset trigger / Pulse Width Trigger / Start & Stop Trigger (Software Selectable) 45 (W) x 45 (H) x 43.5 (D) mm USB2.0 High Speed +5 V through USB connector / DC Jack 45 (W) x 45 (H) x 51.5 (D) mm Less than 450 ma C Mount 45 (W) x 45 (H) x 43.5 (D) mm BM08B-SRSS-TB (JST) Approximately 45g 0 to 40⁰C -30 to 65⁰C RoHS Compliant - 45 (W) x 45 (H) x 51.5 (D) mm Product Specification 6 Rev 1.9
B. Connector Specifications 8 8 1 1 (2) (1) (3) (2) (1) (3) Straight Type Right-angle Type 1. USB Connector Please connect the USB cable to this connector. 2. Input / Output signal connector: BM08B-SRSS-TB (JST) Wire Connector (Board Level): WIR-630-8 Pin Assignment: No. Signal I/O 1 +5V DC 2 GND 3 N.C. 4 N.C. 5 IO0 IN 6 IO1 IN 7 IO2 OUT 8 IO3 OUT 3. 5V Power Jack Please supply 5V to this connector. Product Specification 7 Rev 1.9
C. Input / Output Signals Specifications (Board Type) 1. Input Signals Specifications Input signal pins (IO0 and IO1) can be configured with Trigger Input or Readout Request a. Trigger Input Signal Requirements 1) Input Signal Level: High: 2.5 to 5V Low: 0 to 0.3 V 2) Input Impedance: 10 k Ohm 3) Pulse Polarity: Positive or Negative (selectable by the software) 4) Pulse Width: 50 clock to 0.5 seconds Normal clock: 1.35803 useconds to 0.5 seconds 1/2 clock: 2.71607 useconds to 0.5 seconds 1/4 clock: 5.43210 useconds to 0.5 seconds 2.5 to 5V 0 to 0.3 V 50 clock to 0.5 seconds b. Read Out Request Input Signal Requirements 1) Input Signal Level: High: 2.5 to 5 V Low: 0 to 0.3 V 2) Input Impedance: 10k Ohm 3) Pulse Polarity: Positive or Negative (selectable by the software) 4) Pulse Width: 50 clock to 0.5 seconds Normal clock: 1.35803 useconds to 0.5 seconds 1/2 clock: 2.71607 useconds to 0.5 seconds 1/4 clock: 5.43210 useconds to 0.5 seconds 2.5 to 5 V 0 to 0.3 V 50 clock to 0.5 seconds Product Specification 8 Rev 1.9
2. Output signals specifications Output signal pins (IO2 and IO3) can be configured with Strobe signal output, Trigger output, End of exposure or End of Transfer through the software. a. Strobe (Exposure time) output signal specifications 1) Output signal level: 3.3 Vp-p 2) Output impedance: High-impedance 3) Pulse polarity: Positive or Negative (selectable by the software) 4) Pulse width: Exposure time 3.3 V 0 V Exposure time b. Strobe (strobe signal setting) output signal specifications 1) Output signal level: 3.3 Vp-p 2) Output impedance: High-impedance 3) Pulse polarity: Positive or Negative (selectable by the software) 4)Pulse width: Exposure time + setting time 3.3 V 0 V Exposure time + setting time c. Trigger (through) output signal specifications 1) Output signal level: 3.3 Vp-p 2) Output impedance: High-impedance 3) Pulse polarity: Positive or Negative (selectable by the software) 4) Pulse width: As same as input trigger signal 3.3 V 0 V Same as input trigger signal Product Specification 9 Rev 1.9
d. Trigger output signal specifications 1) Output signal level: 3.3 Vp-p 2) Output impedance: High-impedance 3) Pulse polarity: Positive or Negative (selectable by the software) 4) Pulse width: 1 clock to 4094 clocks (selectable by the software) Normal clock: 27.1606 nseconds to 111.196 useconds 1/2 clock: 54.3213 nseconds to 222.391 useconds 1/4 clock: 108.642 nseconds to 444.780 useconds 3.3 V 0 V 1 clock to 4094 clock e. End of exposure output signal specifications 1) Output signal level: 3.3 Vp-p 2) Output impedance: High-impedance 3) Pulse polarity: Positive or Negative (selectable by the software) 4) Pulse width: 1 clock to 4094 clocks (selectable by the software) Normal clock: 27.1606 nseconds to 111.196 useconds 1/2 clock: 54.3213 nseconds to 222.391 useconds 1/4 clock: 108.642 nseconds to 444.780 useconds 3.3 V 0 V 1 clock to 4094 clock f. End of transfer output signal specifications 1) Output signal level: 3.3 Vp-p 2) Output impedance: High-impedance 3) Pulse polarity: Positive or Negative (selectable by the software) 4) Pulse width: 1 clock to 4094 clocks (selectable by the software) Normal clock: 27.1606 nseconds to 111.196 useconds 1/2 clock: 54.3213 nseconds to 222.391 useconds 1/4 clock: 108.642 nseconds to 444.780 useconds 3.3 V 0 V 1 clock to 4094 clock Product Specification 10 Rev 1.9
II. Dimensions A. Dimensions (STC-TC152USB-AT: Color / Right-Angle / Case Type) U1 (C mout screw) 2-M2.6 (Depth 4) 2-M2 (Depth 3) 51 (5.5) 12 40.6 8 51 17 18 8 51 18 (11) 11 7.7 2-M6 (Depth 8) 11 1/4" 20UNC (Screw for tripod) B. Dimensions (STC-TC152USB-AS: Color / Straight / Case Type ) Unit: mm U1 (C mout screw) 2-M2.6 (Depth 4) 51 (5.5) 12 43.3 17 2-M2 (Depth 3) (11) 11 7.7 2-M6 (Depth 8) 11 1/4" 20UNC (Screw for tripod) Unit: mm Product Specification 11 Rev 1.9
C. Dimensions (STC-TC152USB-BTC: Color / Right-Angle / C Mount / Board Type) Unit: mm D. Dimensions (STC-TC152USB-BSC: Color / Straight / C Mount / Board Type) Unit: mm Product Specification 12 Rev 1.9
E. Dimensions (STC-TB152USB-AT: Monochrome / Right-Angle / Case Type) U1 (C mout screw) 2-M2.6 (Depth 4) 2-M2 (Depth 3) 51 (5.5) 12 40.6 8 51 17 18 8 51 18 (11) 11 7.7 2-M6 (Depth 8) 11 1/4" 20UNC (Screw for tripod) Unit: mm F. Dimensions (STC-TB-152USB-AS: Monochrome / Straight / Case Type) U1 (C mout screw) 2-M2.6 (Depth 4) 51 (5.5) 12 43.3 17 2-M2 (Depth 3) (11) 11 7.7 2-M6 (Depth 8) 11 1/4" 20UNC (Screw for tripod) Unit: mm Product Specification 13 Rev 1.9
G. Dimensions (STC-TB152USB-BTC: Monochrome / Right-Angle / C Mount / Board Type) Unit: mm H. Dimensions (STC-TB152USB-BSC: Monochrome / Straight / C Mount / Board Type) Unite: mm Product Specification 14 Rev 1.9
Revisions Revision Date Changes Name Changes 1.0 2008/01/24 New Document Sam Aimono 1.1 2008/03/26 Specifications update (Scanning methods) Add Binning and binning partial (1/1, ½, ¼, variable) for the monochrome type Sam Aimono 2008/05/14 Edited English Michelle Campbell Specifications update (Trigger Mode) Add Pulse width trigger for the trigger mode Add Start & Stop Trigger for the Trigger mode 1.2 2009/03/31 Specifications update (Mechanical specifications of board type) Add Interface Connector Add Connector Specifications (Board Type) Add Input / Output signals specifications (Board Type) 1.3 2009/10/28 Added Wire Connector: WIR-630-8 to page 7 Specifications update (Pixel frequency) Add 1/2 and 1/4 clock speed for the pixel frequency Specifications update (Maximum frame rate) Add 1/2 and 1/4 clock speed for the maximum frame rate 1.4 2010/10/06 Specifications update (Minimum Scene Illumination) Change the minimum scene illumination Specifications update (Temperature) Delete the humidity Specifications update Change from the Environmental conditions to the Environmental specifications. Add the time for Input / Output Signals Specifications Sam Aimono 1.9 2011/07/11 Revise the active picture elements. Revise the resolution Editor s Note: Changed revision number to match STJ: 1.5 1.9 Product Specification 15 Rev 1.9
Sensor Technologies America, Inc. 1345 Valwood Pkwy, Suite 320 Carrollton, Texas 75006-6891 TEL (972) 481-9223 FAX (972) 481-9209 URL http://www.sentechamerica.com/ Sensor Technology Co., Ltd. 7F, Harada Center Building 9-17, Naka cho 4chrome Atsugi-city, Kanagawa 243-0018 Japan TEL +81-46-295-7061 FAX +81-46-295-7066 URL http://www.sentech.co.jp/ Taiwan Sensor Technology, Inc. 3F-6, No. 9, Aiguo W, Rd,. Jhong Jheng District Taipei City 100, Taiwan, R.O.C. TEL 886-2-2383-2331 FAX 886-2-2370-8775 EMAIL: sentech0501@yahoo.com.tw Product Specification 16 Rev 1.9