PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE TFTLCD SBU AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE TFT LCD SBU AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST TITLE : HT2V Preliminary Product Specification P BOE TFTLCD SBU BEIJING BOE OPTOELECTRONICS TECHNOLOGY BOE HYDIS TECHNOLOGY SPEC. NUMBER PRODUCT GROUP. TFT LCD P 5.7.2 OF 25 B232B(/3) A4(2 X 297)
P 5.7. 2 ISION HISTORY. ECN NO. DESCRIPTION OF CHANGES DATE PREPARED P Initial Release 5.6.. W.K. Chang P Change Brightness 5 nit 45 nit typ. 5.7.2 W.K. Chang Change View angle 6/4 typ. (CR>5) 5/3 typ. (CR>) HT2V Product Specification OF 25 B232B(2/3) A4(2 X 297)
P 5.7.2. Contents No.. 2. 3. 4. 5. 6. 7. 8. 9... 2. 3. 4. 5. Item General Description Absolute Maximum Ratings Electrical specifications Optical specifications Interface Connection Signal Timing Specifications Signal Timing waveforms of Interface Signal Input Signals, Display Colors & Gray Scale of Colors Power Sequence Mechanical Characteristics Reliability Test Handling & Cautions Product Serial Number Packing Appendix Page 4 6 7 8 4 6 8 9 2 2 22 23 24 26 HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
. GENERAL DESCRIPTION. Introduction PRODUCT GROUP P 5.7.2. HT2V is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 2. inch diagonally measured active area with VGA resolutions (64 horizontal by 48 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 6,777,26 colors. The TFTLCD panel used for this module is adapted for a low reflection and higher color type. RGB Source Driver Circuit TTL 8bit +5.V CN (5pin) LVDS Tx Timing Controller (LVDS Rx + RSDS) Power Circuit Block Gate Driver Circuit G G48 S S64 TFT LCD Panel (64 RGB 48 pixels) Back light Assembly (6 CCFL Top Bottom Edge Type).2 Features TTL Interface with pixel / clock Highspeed response Low power consumption 8bit color depth, display 6,777,26 colors Incorporated edge type backlight (Four lamps) High luminance and contrast ratio, low reflection and wide viewing angle DE (Data Enable) only Mode RoHS Compliant HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2..3 Application TV use.4 General Specification The followings are general specifications at the model HT2V. <Table. General Specifications> Parameter Specification Unit Remarks Active area 48(H) 36(V) mm Number of pixels 64(H) 48(V) pixels Pixel pitch.6375(h).6375(v) mm Pixel arrangement RGB Vertical stripe Display colors 6,777,26 colors Display mode Normally White Dimensional outline 448.6 339.6 25. (max.) mm Weight 32 (typ.) g Surface Treatment Haze 25%, 3H Backlight Top/Bottom edge side, 6CCFL type HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 2. ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and nonoperational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> [VSS==V] Parameter Symbol Min. Max. Unit Remarks Power Supply Voltage Logic Supply Voltage V DD V IN VSS.5 VSS.3 6.5 V DD +.3 V V Ta = 25 Backlight Lamp Current I BL 3 7 ma Backlight Lamp frequency F L 4 7 khz Operating Temperature T OP +5 ) Storage Temperature T ST 2 +6 ) Note : ) Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 O C max. and no condensation of water. HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
3. ELECTRICAL SPECIFICATIONS 3.Electrical Specifications < Table 3. Electrical specifications > P 5.7.2. [Ta =252 ] Parameter Min. Typ. Max. Unit Remarks Power Supply Voltage Power Supply Current V DD I DD 4.5 5. TBD 5.5.2 V A Note Permissible Input Ripple Voltage V RF mv V DD = 5.V In Rush Current Irush 3. A Note 2 Backlight Lamp Voltage V BL 755 V rms Backlight Lamp Current I BL 3. 6.5 7. ma rms Backlight Lamp operating Frequency F L 4 7 KHz Note 3 Lamp Start Up Voltage 45 V rms Note 4 Lamp Life 5 Hrs I BL = 8.mA Power Consumption P D TBD 6 W P BL 29.4 W I BL =6.5mA, Note 5 P total TBD W Notes :. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD=5.V, Frame rate=75hz and Clock frequency = 67.5MHz. Test Pattern of power supply current a) Typ : Color Bar pattern b) Max : Vertical 2 line pattern 2. The duration of rush current is about 2ms and rising time of Power Input is ms(min) 3. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display 4. The voltage above this value should be applied to the lamps for more than second to startup. Otherwise the lamps may not be turned on. 5. Calculated value for reference (V BL I BL ) 6 excluding inverter loss. HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 4. OPTICAL SPECIFICATION 4. Overview The test of Optical specifications shall be measured in a dark room (ambient luminance lux and temperature = 25±2) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM5) and test unit shall be located at an approximate distance 5cm from the LCD surface at a viewing angle of and equal to. We refer to Ø= (= 3 ) as the 3 o clock direction (the right ), Ø=9 (= 2 ) as the 2 o clock direction ( upward ), Ø=8 (= 9 ) as the 9 o clock direction ( left ) and Ø=27 (= 6 ) as the 6 o clock direction ( bottom ). While scanning and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 3 minutes warmup period. VDD shall be 5.V +/% at 25 C. Optimum viewing angle direction is 6 clock. 4.2 Optical Specifications Parameter [VDD = 5.V, Frame rate = 6Hz, Clock = 25.8MHz, I BL = 6.5mA, Ta =252 ] Symbol Condition Min. Typ. Max. Unit Remark Viewing Angle range Horizontal Vertical 3 9 2 6 CR > 75 75 7 6 Deg. Deg. Deg. Deg. Note Luminance Contrast ratio CR 55 7 Note 2 Luminance of White Y w 35 45 cd/m 2 Note 3 White luminance uniformity Y 75 8 % Note 4 White W x W y.25.26.28.29.3.32 Reproduction of color Red Green R x R y G x G y = (Center) Normal Viewing Angle TBD TBD TBD TBD Note 5 Blue B x TBD B y TBD Response Time Rise Decay T r T d 8 2 ms Note 6 Cross Talk CT 2. % Note 7 HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. Note :. Viewing angle is the angle at which the contrast ratio is greater than. The viewing are determined for the horizontal or 3, 9 o clock direction and the vertical or 6, 2 o clock direction with respect to the optical axis which is normal to the LCD surface. 2. Contrast measurements shall be made at viewing angle of θ= and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR = Luminance when displaying a white raster Luminance when displaying a black raster 3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. 4. The White luminance uniformity on LCD surface is then expressed as : Y = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * (See FIGURE 2 shown in Appendix). 5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 6. The electrooptical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the data input signal ON and OFF. The times needed for the luminance to change from % to 9% is Td, and 9% to % is Tr. 7. CrossTalk of one area of the LCD surface by another shall be measured by comparing the luminance (Y A ) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (Y B ) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix). HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 5. INTERFACE CONNECTION. 5. Electrical Interface Connection CN Module Side Connector : User Side Connector : Hirose FH25S.5SH or Equivalent Pin No Symbol Function Remark Pin No Symbol Function Remark NC NO CONNECTION 26 R RED DATA 2 NC NO CONNECTION 27 3 NC NO CONNECTION 28 G7 4 5 29 3 G6 G5 GREEN DATA (G7 : MSB) 6 VCC 3 G4 7 8 VCC VCC POWER SUPPLY ( + 5.V ) 32 33 G3 9 VCC 34 35 G2 G GREEN DATA NC NO CONNECTION 36 G 2 NC NO CONNECTION 37 3 38 B7 4 5 DE DATA ENABLE 39 4 B6 B5 BLUE DATA (B7 : MSB) 6 DCLK DOT CLOCK 4 B4 7 42 8 R7 43 B3 9 R6 RED DATA 2 R5 (R7 : MSB) 44 45 B2 B BLUE DATA 2 R4 46 B 22 47 23 R3 48 24 R2 RED DATA 49 NC NO CONNECTION 25 R 5 NC NO CONNECTION HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 5.2 Data Input Format Display Position of Input Data (VH) 5.3 Backlight Interface Connection CN2, 22, 23 CN24, 25, 26 Lamp Position Center Outer CN23 CN26 CN2 CN22 CN24 CN25 Module Side Connector User Side Connector CN NO. PIN NO. INPUT 2 2 2 HOT COLD HOT COLD HOT COLD BHSR2VS (JST) or equivalent SM2BHSSTB (JST) or equivalent COLOR FUNCTION White High Voltage White Ground Pink High Voltage Blue Ground Blue High Voltage Pink Ground HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 6. SIGNAL TIMING SPECIFICATION 6. The HT2V is operated by the DE only mode ( TTL Input ) ITEM Symbol Min Typ Max Unit Note CLK Period Frequency t CLK 2 39.7 25.8 35 ns MHz Hsync Frequency f H 3.5 KHz Vsync Frequency f V 6 Hz Horizontal Active Display Term Valid Total t HV t HP 68 64 8 56 t CLK Vertical Active Display Term Valid Total t VV t VP 485 48 525 627 t HP HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 7. SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL 7. Sync Timing Waveforms DCLK tclk.5 VDD Valid data First data Invalid data Pixel, Pixel 2, Invalid data Valid data Second data Invalid data Pixel, Pixel 3, Invalid data DE(Data Enable) HSync thp thv DE(Data Enable) tvp VSync tvv DE(Data Enable) HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
B232B(3/3) A4(2 X 297) SPEC. NUMBER SPEC. TITLE HT2V Product Specification PRODUCT GROUP P OF 25 5.7.2. 8. INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS Green Brighter Darker Black Gray Scale of GREEN Blue Brighter Darker Black Gray Scale of BLUE White Yellow Magenta Red Cyan Green Blue Black Basic Colors Red Brighter Darker Black Gray Scale of RED Darker Brighter White B6 B5 B4 B3 B2 B B G5 G4 G3 G2 G G G6 R3 R4 R5 R6 R R2 R B7 G7 R7 Black Gray Scale of WHITE BLUE DATA GREEN DATA RED DATA Color & Gray Scale
P 5.7.2. 9. POWER SEQUENCE To prevent a latchup or DC operation of the LCD module, the power on/off sequence shall be as shown in below T ms T2 5 ms 2ms T3 2ms T4 T5 5ms T6 ms sec T6 Notes:. When the power supply VDD is V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. Back Light must be turn on after power for logic and interface signal are valid. HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
. MECHANICAL CHARACTERISTICS. Dimensional Requirements P 5.7.2. FIGURE 6 (located in Appendix) shows mechanical outlines for the model HT9E. Other parameters are shown in Table 5. <Table 5. Dimensional Parameters> Parameter Dimensional outline Weight Active area Pixel pitch Number of pixels Backlight Specification 448.6 339.6 25. (max.) 32 (typ.) 48(H) 36(V).6375(H).6375(V) 64(H) 48(V) ( pixel = R + G + B dots) Top / Bottom edge side 6CCFL type Unit mm gram mm mm pixels.2 Mounting See FIGURE 5. (shown in Appendix).3 AntiGlare and Polarizer Hardness. The surface of the LCD has an antiglare coating to minimize reflection and a coating to reduce scratching..4 Light Leakage There shall not be visible light from the backlighting system around the edges of the screen as seen from a distance 5cm from the screen with an overhead light level of 35lux. HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
. RELIABLITY TEST PRODUCT GROUP The Reliability test items and its conditions are shown in below. <Table 6. Reliability Test Parameters > P 5.7.2. No 2 3 4 5 6 7 Low temperature operation test Thermal shock Vibration test (nonoperating) Test Items High temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Conditions Ta = 6, 24 hrs Ta = 2, 24 hrs Ta = 5, 8%RH, 24hrs Ta = 5, 24hrs Ta =, 24hrs Ta = 2 6 (.5 hr), cycle Frequency ~ 3 Hz, Sweep rate 3 min Gravity / AMP.5 G Period X, Y, Z 3 min Gravity Shock test 8 Pulse width (nonoperating) 5G msec, sine wave Direction X, Y, Z Once for each 9 Electrostatic discharge test (nonoperating) Air : 5 pf, 33, 5 KV Contact : 5 pf, 33, 8 KV HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 2. HANDLING & CAUTIONS () Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. (2) Cautions for handling the module As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and back light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. (3) Cautions for the operation When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. (4) Cautions for the atmosphere Dew drop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electroconductive polymer packing pouch and under relatively low temperature atmosphere is recommended. (5) Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. (6) Other cautions Do not disassemble and/or reassemble LCD module. Do not readjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages. HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 3. PRODUCT SERIAL NUMBER HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 4. Packing 4. Packing Order Put Pad into the box. Put silica gels in the box. After sealing the box, attach Packing Label on the attach position sign area of the box. Place a cover on the top of the box. As shown in the figure, place the Modules bundled by shielding bag in the box. HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 4.2 Packing Note Box Dimension : 346mm(W) 526mm(D) 448mm(H) Package Quantity in one Box : 5pcs 4.3 Box label Label Size : 8 mm (L) 56 mm (W) Contents Model : HT2V Q`ty : Module Q`ty in one box Serial No. : Box Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of Product HT2V ### FG CODE HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. 5. APPENDIX Figure. Measurement Set Up Figure 2. White Luminance and Uniformity Measurement Locations (5 points) HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. Figure 3. Response Time Testing Display data White(TFT OFF) Black(TFT ON) White(TFT OFF) Optical Response % 9% TR TF % % Time Figure 4. Cross Modulation Test Description VIEW AREA VIEW AREA L3 32,256 96,256 Y B (2, 52) 32,768 96,768 Y A (2,52) L Y B Y CrossTalk (%) = A Y A Where: Y A = Initial luminance of measured area (cd/m 2 ) Y B = Subsequent luminance of measured area (cd/m 2 ) The location measured will be exactly the same in both patterns HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. Figure 5. TFTLCD Module Outline Dimensions (Front view) HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)
P 5.7.2. Figure 6. TFTLCD Module Outline Dimensions (Rear view) HT2V Product Specification OF 25 B232B(3/3) A4(2 X 297)