velocity standard 07 V-S-07 Chic and robust - a highly-structural portable 10 x10 exhibit that emphasizes your identity and message seamlessly with a combinaton of fabric graphics, rigid accents and accessories. features and benefits: - Custom appearance - Easy to assemble - Combination of rigid and fabric graphics - Aluminum construction: vertical extrusions 50mm x 100mm - Fully printed counter graphics dimensions: Hardware Assembled unit: 111.5 (w) x 99.375 (h) x 47.5 (d) approx. 2832.1mm(w) x 2524mm(h) x 1206.5mm(d) Counter: 39.37 (w) x 40.5 (h) x 15.2 (d) approx. 999mm(w) x 1028.7mm(h) x 386.08mm(d) Counter internal dimensions: 36.3 (w) x 39.37 (h) x 13.8 (d) approx. 922mm(w) x 1000mm(h) x 351mm(d) Shipping Shipping dimensions - ships in 3 cases Each WMC12x6 case: 52 (l) x 30 (w) x 15 (h) 1320.8mm(l) x 762mm(w) x 381mm(h) Approximate shipping weight (entire kit): 375 lbs / 170.1 kgs additional information: Graphic materials: dye-sublimated fabric & UV prints on 6mm sintra Counter holds max weight 100 lbs / 45.4 kgs Tabletop colors: - Kit includes one frame, one graphic header, five fabric graphic panels, two roller graphic panels, three 50 watt spotlights, one literature holder, one monitor bracket, one storage counter and three WMC12x6 molded cases - Lifetime hardware warranty against manufacturer defects Graphic Panel A,B,C: Total visible area: 11.81 w x 87.32 h 299.9mm(w) x 2217.9mm(h) Panel D: Total visible area: 46.30 w x 86.61 h 1176.1mm(w) x 2199.9mm(h) Panel E & G: Total visible area: 23.62 w x 87.32 h 599.9mm(w) x 2217.9mm(h) Panel F: Total visible area: 34.49 w x 86.61 h 876mm(w) x 2199.9mm(h) Header: Total visible area: 42.375 w x 12 h 1076.325mm(w) x 304.8mm(h) Refer to related graphic template for more information Monitor mount max weight: 50 lbs / 22.7 kgs Lights included: LV1 50 watt, low voltage spotlight, curved arm, silver finish, 19.5 from end to end Canopy can be upgraded to dye-sublimated graphic printed silver black mahogany natural velocity 08.12.15 Nimlok Display and Exhibit Solutions Worldwide For questions contact your local Nimlok distributor
Parts included Part label Qty Part code x16 PM4S3-1200-A-A VE-07 x2 PM4S3-600-L-L VE-08 x2 PM4S3-300-L-L VE-09 x1 PH2-1200-S-S VE-10 x1 PH2-900-S-S VE-99 x2 PS2 VE-11 x2 PH2-600-S-S VE-12 x4 PH2-300-S-S x8 PH2C-1 VE-31 x6 PH-351-S-S Part label Qty Part code Graphic clip x9 - Tool kit x1 V-TK-01 Light x3 LV1-CLP-LIGHT Curved canopy x1 V-S-CAN-02 Standoff x2 CKSO Cable display x1 V-CK3A Monitor mount x1 LM-MB Step stool x1 STEP STOOL Steamer x1 FABRIC STEAMER-ES [3048mm] VE-44 x1 PM4S2-300-L-L SP VC-03 x1 V-CAB-02-DR V-LWS-CT-02 x1 V-LWS-CT-02 Panel A x1 - Panel B x1 - Panel C x1 - VE-53 panel D x1 PM4-RB4 10'-0" [3048mm] Panel E x1 - VE-54 panel F x1 PM4-RB3 Panel G x1 - Header x1 - Counter infill x3-1.
Step 1. Moving from left to right, connect uprights at base using the VE-12s, VE- 08, VE-11s and VE-10 as designated in the diagram below. Connect using the attachment detail shown. Note that the VE-09 and VE-10 lock into the center channel of the upright. Take care to turn locks only half a turn. Step 2. Attach internal connectors to lower uprights using the attachment detail shown below. Slide upper s over the internal connectors to complete the vertical posts. VE-12 VE-09 VE-10 VE-11 VE-12 VE-11 VE-12 VE-12 V-12 VE-12 WITH S WITH S POST W/ STOP 1-2- Tension Glides TOP BOTTOM STOP STOP HORIZONTAL BY HORIZONTAL BY 2.
VE-08 Step 3. Connect the VE-08/VE-44 horizontals to the completed uprights where designated in the diagram using the attachment detail below. VE-08 VE-07 VE-07 Step 4. Assure monitor mount is secured to the VE-99s using the wingnuts as seen in the attachment detail below. Attach both VE-99s, with monitor mount attached, to the designated uprights using attachment detail below. VE-44 WITH S WITH S HORIZONTAL BY HORIZONTAL BY 3.
Step 5. Attach VE-53/VE-54 to the designated uprights as shown in attachment detail. Insert graphic clips into VE-09/VE-10 where designated and turn clockwise to tighten. Pull graphics down from VE-53/VE-54 and snap rods into clips. When removing, never pull on the graphic, always pull on the graphic rod. VE-53 VE-53 PANEL D VE-54 PANEL VE-54 F PH GRAPHIC CLIP HORIZONTAL BY BOTTOM Dyesub Graphic Graphic Rod CLIP MIDDLE CHANNEL The CLIP locations are represented by orange dots on the drawings. 4.
Step 6. Using the attachment detail show, push rubber gasket around edge of panels A, B, C, E and G into the designated channels as seen in diagram below. GRAPHIC PANEL G E GRAPHIC PANEL G I TOP GRAPHIC PANEL B GRAPHIC PANEL C GRAPHIC PANEL A PULL TABS Fabric graphic is installed by pressing into TOP and BOTTOM channel. To pull the graphic out of the channels, use TABS on the back side. BOTTOM PULL TABS Fabric graphic is installed by pressing into TOP and BOTTOM channel. To pull the graphic out of the channels, use TABS on the back side. 5.
Step 7. To attach cable display, insert clips on end of cables into the front channel of both the VE-12 and VE-44 and twist gently to the right to tighten. To attach header, connect two standoffs to the front channel of designated uprights using detail below. Attach wings to the standoffs using detail below. CHANNEL CABLE DISPLAY TOP CABLE DISPLAY BROCHURE OR GRAPHIC HEADER 2.5 MM HEX KEY STANDOFF STANDOFF CABLE STANDOFF CHANNEL 2.5 MM HEX KEY CABLE DISPLAY Twist in extrusion channel. Gently tight in place BOTTOM Attach STANDOFF to brochure or sintra and gently tight in place. Then link Cables to extrusions top and bottom CABLE DISPLAY STANDOFF INSTALL CABLE DISPLAY IN THE FRONT CHANNEL STANDOFF Top STANDOFF DETAIL Graphic Channel of extrusion NT Toggle STANDOFF STANDOFF Barrel Screw the NT toggle into the base of the STANDOFF barrel and then insert the NT toggle into the channel of the extrusion and twist to tighten into place. Next, place the top of the STANDOFF through the hole in the graphic and then screw on the STANFOFF top to secure the graphic in place. 6.
Step 8. Assemble the canopy by connecting the pieces following the numbered labels. Clean the frame and place it on a clean surface. Carefully remove the graphic and place it around the bottom of the frame, slits on underside of graphic. Pull the cover carefully over the frame and close all zippers. When breaking system down, be sure to fold or roll the graphic neatly and place in bag. Screw supplied plates to the top of designated s as shown in detail below. Slide completed canopy onto tube secured to the plate. CURVED CANOPY CURVED CANOPY SET UP INSTRUCTIONS: 1. CONNECT BOTTOM AND TOP RAILS FOLLOWING THE LABELS 2. CONNECT SIDE RAILS 3. CLEAN THE FRAME AND PLACE THEM ON CLEAN PLACE 4. CAREFULLY REMOVE FABRIC COVER FROM BAGS 5. PLACE COVER AROUND THE BOTTOM OF THE FRAME 6. PULL COVER CAREFULLY UP TO THE TOP 7. CLOSE ALL ZIPPERS 1 8. ADJUST FABRIC AROUND THE FRAME Frame Assembly Assemble frame as shown 2 BREAK DOWN INSTRUCTIONS: REVERSE SET-UP STEPS TO BREAKDOWN FRAME FABRIC CARE INSTRUCTIONS: 1. UNZIP COVER ZIPPERS 2. CAREFULLY REMOVE FABRIC COVER 3. CLOSE ALL ZIPPERS 4. FOLD OR ROLL NEATLY 5. PLACE FABRIC IN COVER BAG PART LIST: PER UNIT 6 30MM DIA. TUBE SECTIONS 1 FABRIC COVER 5 4 6 3 #8 SHEET METAL SCREW REQUIRED W/MINIMUIM OF 3/4" LENGTH TO SCREW THE PLATE TO THE 30MM TUBE #8 SCREW ZIPPER PLATE NOTCH BOTTOM FABRIC PANEL ON CENTER OF THE SPREADER TUBES FOR TUBE CONNECTION (1.25" DIA.). slits in graphic go on the underside of frame VERTICAL 7.
Step 9. Lock VE-31s at bottom of designated uprights using attachment detail below. Attach SP VC-03 counter door, VE-63 and remaining VE-31 to the secured VE-31s. Step 10. Slide front and side infills into the channels of the, SP VC-03 counter door, and VE-63 uprights. SP VC-03 P90R-1000 VE-63 SIDE INFILL FRONT INFILL SIDE INFILL VE-31 VE-31 VE-31 WITH S HORIZONTAL BY 8.
Step 11. Connect three upper VE-31s where designated in diagram below using the attachment detail shown. Set V-LSW-CT-02 counter top onto completed frame. WITH S VE-31 V-LSW-CT-02 VE-31 VE-31 HORIZONTAL BY 9.
Step 12. Slide two lights onto clips and place in middle channel of VE-53 as shown in detail below. LIGHT LIGHT LIGHT LIGHT W/ CLIP Light clip 1- Slide light clip onto the LIGHT. 2-Then slide the LIGHT into the channel at an angle and then gently lower down. LV1 Light 10.
check out these related products: velocity standard 01 velocity standard 05 velocity standard 02 velocity standard 06 velocity standard 03 velocity standard 07 Redesign of this exhibit without approval by Nimlok may result in dangerous and unsafe structures. Nimlok disclaims any responsibility for redesigned exhibits it does not approve in writing. Parts and components such as panels and extrusions are manufactured to metric sizing. We continue to improve and modify our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. See Graphic Templates for graphic bleed specifications. velocity standard 04 velocity standard 08