L SERIES Hypertac modular connectors employ a do-ityourself system based on the building block principle. They offer a wide variety of combinations available in a single connector frame. Thus, the user is capable of selecting the connector that fulfills the exact requirements with off-the-shelf components. One of the many advantages of the Hypertac contact used is its low extraction and insertion forces. In this application it enables the user to assemble large numbers of contacts into a connector which is still able to mate and unmate smoothly and easily The L series can be built up for the following: Rack and panel applications -- Standard -- With jackscrews (standard & quick disconnect) -- With floating mounting Cable applications -- Hooded with rounded or flat cable clamps -- With jack screws (standard & quick disconnect) Programming applications The system is composed of two basic elements: the modules and the frames. 1. The modules are the connector elements of the system. Various types of contacts are available, such as signal, power, coaxial, etc. These contacts are mounted in small plastic blocks. Crimp contacts are also available in plastic blocks that can be mounted individually or together into the frame. The width of each module block is designated in units. The modules have fixed contacts with: 2 contacts @ 50 200 amps amps (Type M) P) 2 contacts @ 25 50amps (Type C) M) 32 contacts @ 15 25amps (Type B) C) 54 contacts @ 816 amps amps (Type A) N) 17 3 contacts @ 815 amps amps (Type D) B) 5 contacts @ 8 amps (Type A) 17 contacts @ 8 amps (Type D) 2 contacts @ 5 amps (Type E) 2 contacts high voltage (Type H) SnapIn crimpcontacts: 1 contact @ 200 amps (Type G) 1 contact @ 100 amps (Type K) 2contacts @25and50amps(TypeU) 3 contacts @ 25 amps (Type V) 3 contacts @ 15 amps (Type S) 5 contacts @ 8 amps (Type R) 30 contacts @ 4 amps (Type W) 3 contacts coaxial (Type V) 2. The frames hold the modules in position. They range from a basic frame consisting of 2 side rails and 2 end caps to more complex versions with jack screws, hoods, cable clamps, etc. All frames are available in numerous lengths to conform to almost any combination of modules. With the L Series, specially designed connectors can be purchased quickly and inexpensively, eliminating the extra cost and delay of custom tooling. Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com 4 / 1
5 4 3 2 1 L SERIES MULES Module A 8 Amp Contact Rating H Width: 1 Unit H Contacts: 5 Hypertac R Fixed Contacts H.059 (1.50mm) Gender Termination Plating Part Number.079 (2.00).063 (1.60) Up to 16 AWG LAFSTAH.177 (4.50).039 (1.00) Straight Dip Solder LAFDTAH (9.00).630 (16.00).157 (4.00).984 (25.00).209 (5.30) Empty Block ZLM005--001 (LAHT).059 (1.50) 10 in LAMST.079 (2.00).256.063 (1.60) Up to 16 AWG LAMSTH.059 (1.50) (9.00).256 Straight Dip Solder 10 in LAMDT.039 (1.00) LAMDTH Crimp Termination: R See Modules page L3. Crimp R Modules Intermate Intermate with A Modules. with A Modules. Plating Reference: Pins: Sockets: S 10 in gold (min) over Ni S 50 in gold (min) over Ni S 50 in gold (min) over Ni on mating surface, gold flash over Ni on termination 1) S For ordering information regarding modules assembled in frames,, see page pg. L20 4/18. 2) S Dimensions in inches (mm) 3) S If assembling the modules into a frame, two YHD0027 clips are required per module File No.: UL E102195 Extraction Force Contact Life Cycles Breakdown voltage Dielectric Withstanding Voltage Insulation Resistance Temperature Rating Insulator Contact Material: Approx. Weight: (pin) (socket) 8amps < 2.5 milliohms 1--5oz. >100,000 >2000V RMS 1500V RMS >10 6 megohms @ 500 VDC -- 55C to+125c Diallyl-phthalate Brass BeCu wires + brass body M:.2 oz. (6.2g) F:.15 oz. (4.3g) 4 / 2 Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com
5 4 3 2 1 Module R 8 Amp Contact Rating.280 (7.10) max. L SERIES MULES H Width: 1 Unit H 5 Hypertac R Snap In Crimp Contacts H.059 (1.50mm) H Can be mounted by itself or in a frame Gender Wire Dimensions Plating Part Number Replacement Gauge Contact.057.104 18--22 LRF1 YSK015--013AH (1.45) (2.65).022.076 24--26 (.560) (1.93) LRF2 YSK015--009AH.071.108 16 (1.80) (2.75) LRF3 YSK015--014AH.079.122 14 (2.00) (3.10) LRF4 YSK015--045AH.630 (16.00).157 (4.00).197 (5.00).906 (23.00).217 (5.50).104 (2.65) Empty Block ZLR005--001 (LRH) 531 (13.50) 1.142 (29.00).058 (1.48).291 (7.40).213 (5.40).057.104 10 in 18--22 (1.45) (2.65) 24--26.022.076 10 in (.560) (1.93) 16.071.108 10 in (1.80) (2.75) 10 in 14.079.122 (2.00) (3.10) LRM1 LRM1H LRM2 LRM2H LRM3 LRM3H LRM4 LRM4H YPN015--009RG YPN015--009RH YPN015--004RG YPN015--004RH YPN015--010RG 010G YPN015--010RH 010H YPN015--033RG YPN015--033RH and Straight Dip Termination: See page L2. A Modules Intermate with R modules. Crimp tool: AF8 Insertion/Extraction Tool: S0150.01 Positioner: Style 1 & 3 TP592 Style 2 TP655 Style 4 TP1128 Plating Reference ACCESSORIES Pins: S 10 in gold (min) over Ni S 50 in gold (min) over Ni Sockets: S 50 in gold (min) over Ni on mating surface, Contactgold Resistance flash over Ni Extraction termination Force 1) S For ordering information regarding modules assembled in frames, see pg. L20 2) S Dimensions in inches (mm) Extraction Force Contact Life Cycles Breakdown voltage Dielectric Withstanding Voltage Insulation Resistance Temperature Rating Insulator Contact Material: Approx. Weight (pin) (socket) 8amps < 2.5 milliohms 1--5oz. >100,000 >1600V RMS 1200V RMS >10 4 megohms @ 500 VDC -- 55C to+105c Nylon Brass BeCu wires + brass body M:.22 oz. (6.4g) F:.16 oz. (4.6g) Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com 4 / 3, see page 4/18. File No.: UL E102195 File No.: CSA LR83002 -- LRF1, LRF2, LRF3, LRM1, LRM1H, LRM2, LRM2H, LRM3, LRM3H Only
L SERIES MULES Module B 15 Amp Contact Rating H Width: 1.5 Unit H Contacts: 3 Hypertac R Fixed Contacts H.098 (2.50mm) Gender Termination Plating Part Number.138 (3.50).102 (2.60) up to 12 AWG LBFSTAH.177 (4.50).098 (2.50) (9.00) Straight Dip Solder LBFDTAH.256.315 (8.00) Empty Block ZLM003--001 (LBHT).984 (25.00).256.098 (2.48) up to 12 AWG 10 in LBMST LBMSTH.098 (2.48).098 (2.50) Crimp Termination: S See Modules page L5. S Modules Intermate with B Modules. Plating Reference.256 (9.00) Straight Dip Solder Pins: S 10 in gold (min) over Ni S 50 in gold (min) over Ni Sockets: S 50 in gold (min) over Ni on mating surface, Contactgold Resistance flash over Ni Extraction termination Force 1) S For ordering information regarding modules assembled in frames,, see page pg. L20 4/18. 2) S Dimensions in inches (mm) 3) S If assembling the modules into a frame, two YHD0027 clips are required per module File No.: UL E102195 10 in LBMDT Extraction Force Contact Life Cycles Breakdown voltage Dielectric Withstanding Voltage Insulation Resistance Temperature Rating Insulator Contact Material: Approx. Weight (pin) (socket) LBMDTH 15 amps < 1 milliohms 3--25 oz. >100,000 >1600V RMS 1200V RMS >10 6 megohms @ 500 VDC -- 55C to+125c Diallyl--phthalate Brass BeCu wires + brass body M:.35 oz. (10.4g) F:.25 oz. (7.4g) 4 / 4 Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com
22--18 LSF2 L SERIES MULES H Width: 1.5 Units H Contacts: 3 Hypertac R Snap In Crimp Contacts Module S H.098 (2.50mm) H Can be mounted by itself or in a frame 15 Amp Contact Rating Gender Wire Dimensions Plating Part Number Replacement Contact Gauge (9.00) 14--13 12.059.122 LSF1 YSK025--003AH (1.50) (3.10).077.122 (1.95) (3.10).100.150 (2.54) (3.81) YSK025--004AH LSF4 YSK025--013AH.256.324 (8.22) Empty Block ZLS003--002 (LSH).522 (13.25) 1.140 (28.95).098 (2.49).295 (7.50).315 (8.00) 22--18 22--18 14--13 14--13.059.122 (1.50) (3.10).077.122 (1.95) (3.10) 10 in 10 in LSM1 LSM1H LSM2 LSM2H YPN025--002G YPN025--002H YPN025--003G YPN025--003H 12 12.100.150 (2.54) (3.81) 10 in LSM4 LSM4H YPN025--011RG YPN025--011RH and Straight Dip Termination: See page L4. B Modules Intermate with S Modules. ACCESSORIES Crimp tool: M309 Positioner: TP1179 Insertion/Extraction Tool: S0250.01 Plating Reference Pins: S 10 in gold (min) over Ni S 50 in gold (min) over Ni Sockets: S 50 in gold (min) over Ni on mating surface, Contactgold Resistance flash over Ni Extraction termination Force 1) For ordering information regarding modules assembled in frames, see pg. L20 2) Dimensions in inches (mm), see page 4/18. File No.: UL E102195 File No.: CSA LR83002 (milliohms) Extraction Force Contact Life Cycles Breakdown voltage Dielectric Withstanding Voltage Insulation Resistance Temperature Rating Insulator Contact material Approx. Weight: 15 amps < 1.5 milliohms 3.0 -- 28.3 oz. >100,000 >2000V RMS 1500V RMS >10 4 megohms @ 500 VDC -- 55C to+105c Nylon BeCu wires + brass M:.23 oz. (6.5g), F:.35 oz. (10g) Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com 4 / 5
L SERIES MULES Module C&M 25 or 50 Amp Contact Rating C=.138 (3.50) M=.177 (4.50) C=.177 (4.50) M=.193 (4.90).177 (4.50) Width: 2 Units Contacts: 2 Hypertac Fixed Contacts.138 (3.50mm) Rating Gender Termination Plating Amps Part Number 10 AWG 50 in 8AWG 25 50 LCFSTAH LMFSTAH.138 (3.50) (9.00) Straight Dip Solder 50 in 25 50 LCFDTAH LMFDTAH.374 (9.50).425 (10.80) Empty Block ZLM002--001 (LCHT).984 (25.00) Crimp Termination: U Modules Intermate with C and M Modules. Plating Reference.137 (3.48) C =.256 M =.335 (8.50) See Above.137 (3.48).177 (4.50) C =.256 M =.335 (8.50) (9.00).138 (3.50) 10 AWG 8AWG Straight Dip Solder Pins: 10 in gold (min) over Ni 50 in gold (min) over Ni Sockets: 50 in gold (min) over Ni on mating surface, Contactgold Resistance flash over Ni Extraction termination Force 10 in 50 in 10 in 50 in 10 in 50 in 10 in 50 in File No.: UL E102195 1) Recognized components file no.: UL E102195 2) For ordering information regarding modules assembled in frames, see pg. 4 / 18 3) Dimensions in inches (mm) 4) If assembling the modules into a frame, two YHD0027 clips are required per module 25 50 25 50 Extraction Force Contact Life Cycles Breakdown voltage Dielectric Withstanding Voltage Insulation Resistance Temperature Rating Insulator Contact Material: Approx. Weight (pin) (socket) LCMST LCMSTH LMMST LMMSTH LCMDT LCMDTH LMMDT LMMDTH C: 25 amps M: 50 amps C: <.8 m M:.4 m C: 4--32 oz. M: 4--40 oz. 100,000 >3000V RMS 2250V RMS >10 6 Megohms @ 500 VDC -- 55 C to + 125 C Diallyl--phthalate Brass BeCu wires + brass body :.44 oz. (12.5g) :.31 oz. (8.9g) 4 / 6 Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com
Module U 25 or 50 Amp Contact Rating.374 (9.50).266 (6.75) L SERIES MULES H Width: 2 Units H Contacts: 2 Hypertac R Snap In Crimp Contacts H.138.098 (3.50mm) contacts H Can be mounted by itself or in a frame Gender Wire Dimensions Plating Rating Part Replacement Contact Gauge Amps No. 22--20.059.122 (1.50) (3.10) 25 LUF1 YSK035--009AH 18--16.077.122 (1.95) (3.10) 25 LUF2 YSK035--010AH 14--12.112.161 (2.85) (4.10) 25 LUF3 YSK035--011AH 6.217.285 (5.50) (7.25) 50 LUF4 YSK035--030AH 8--10.177.217 (4.50) (5.50) 50 LUF5 YSK035--028AH 2 1.431 (10.95).197.906 (5.00) (23.00).104 (2.65).522 (13.25) Empty Block ZLU002-- 001 (LUH) ACCESSORIES Crimp tool: Styles 1, 2, 3, 5: T1264 Style 4: T712 Postitioner: Styles 1, 2, 3: SP612 Style 4: T758 Style 5: T1559 Insertion/Extraction Tool: S0350.01 and Straight Dip Termination: See page L6. C and M Modules Intermate with U Modules. Plating Reference 1.140 (28.95).137 (3.48).295 (7.50).266 (6.75) 22--20 18--16 14--12.059.122 (1.50) (3.10).059.122 (1.50) (3.10).112.161 (2.85) (4.10).217.285 (5.50) (7.25) Pins: S 10 in gold (min) over Ni S 50 in gold (min) over Ni Sockets: S 50 in gold (min) over Ni on mating surface, Contactgold Resistance flash over Ni Extraction termination Force 1) S For ordering information regarding modules assembled in frames, see pg. L20 2) S Dimensions in inches (mm) 6 8--10.177.217 (4.50) (5.50) 10 in 10 in 10 in 10 in 10 in File No.: UL E102195 File No.: CSA LR83002 LUF5, LUM5, LUM5H Only, see page 4/18. 25 25 25 50 50 LUM1 LUM1H LUM2 LUM2H LUM3 LUM3H LUM4 LUM4H LUM5 LUM5H YPN035--005G YPN035--005H YPN035--006G YPN035--006H YPN035--007G YPN035--007H YPN035--025RG YPN035--025RH YPN035--023RG YPN035--023RH Extraction Force Contact Life Cycles Breakdown voltage Dielectric Withstanding Voltage: Insulation Resistance Temperature Rating Insulator Contact Material: (pin) (socket) Approx. Weight: 25 or 50 amps <.8 milliohms 4--35oz. >100,000 >2800V RMS 2100V RMS >10 4 Megohms @ 500 VDC -- 55C to + 105C Nylon Brass (pin) BeCu wires + brass body M:.45 oz. (12g) F:.29 oz. (7.9g) Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com 4 / 7
6 5 4 3 2 1 9 8 7 L SERIES MULES Module D 8 Amp Contact Rating.063 (1.60).051 (1.30).177 (4.50) H Width: 2 Units H Contacts: 17 Hypertac R Fixed Contacts H.047.047. (1.20mm) Gender Termination Plating Part Number up to 20 AWG LDFSTAH.047 (1.19) (9.00) Straight Dip Solder LDFDTAH.236 (6.00).134 (3.40).067 (1.70).118 (3.00) 12 13 14 15 10 16.984 (25.00) 11 17.423 (10.75) Empty Block ZLM017--001 (LDHT) Plating Reference.046 (1.17).046 (1.18).256.051 (1.30).063 (1.60).047 (1.19).177 (4.50).256 (9.00) up to 20 AWG Straight Dip Solder Pins: S 10 in gold (min) over Ni S 50 in gold (min) over Ni Sockets: S 50 in gold (min) over Ni on mating surface, Contactgold Resistance flash over Ni Extraction termination Force 10 in 1) S For ordering information regarding modules assembled in frames,, see page pg. L20 4/18. 2) S Dimensions in inches (mm) 3) S If assembling the modules into a frame, two YHD0027 clips are required per module File No.: UL E102195 Extraction Force Contact Life Cycles Breakdown voltage Dielectric Withstanding Voltage Insulation Resistance Temperature Rating Insulator Contact Material: (pin) (socket) LDMST LDMSTH 10 in LDMDT LDMDTH 8amps < 3.0 milliohms 1.0 -- 4.5 oz. >100,000 >1800V RMS 1350V RMS >10 6 megohms @ 500 VDC -- 55C to+125c Diallyl--phthalate Brass BeCu wires + brass body Approx. Weight M:.31 oz. (9 g) F:.45 oz. (13 g) 4 / 8 Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com
Module W 4 Amp Contact Rating L SERIES MULES H Width: 2 Units H Contacts: 30 Hypertac R Removable Contacts H 4.024.024 0.60mm) Gender Termination Crimp 18--20 AWG Dimensions.055.035.051.071 (1.39) (.90) (1.30) (1.80) Plating 50 in Part Number LWFRRTAH Replacement Contact YSK006--089AH ) Crimp 22-26 AWG.035.055 (1.39) (.90).051.071 (1.30) (1.80) 50 in LWFRTAH YSK006--011AH 22 26 AWG.039 (1.00).057 (1.45) 50 in LWFSTAH YSK006--010AH.982 (24.95).864 (21.95).700 (17.78).100 (2.54) Empty Block ZLM030-002 ZLM030-- (LWFHT) 001 (LWFHT).100 (2.54).300 (7.62) Empty Block.024 (.60) 32 24 16 8 GUE SOCKET.193 (4.90) M 1 9 1725 GUE PIN.982 (24.95).423 (10.75).059 (1.50).864 (21.95).252 (6.40) Crimp 18--20 AWG Crimp 22-26 AWG 22 26 AWG.035.055 (1.39) (.90).035.055 (1.39) (.90).039 (1.00).051.071 (1.30) (1.80).051.071 (1.30) (1.80).057 (1.45) 10 in 50 in 10 in 50 in 10 in 50 in ZLM030-001 (LWMHT) LWMRRT LWMRRTH LWMRT LWMRTH LWMST LWMSTH YPN006--158G YPN006--158H YPN006--021G YPN006--021H YPN006--020G YPN006--020H Plating Reference ACCESSORIES Crimp Tool: AFM8 Positioner: K547 Extraction Tool: S/DEM1.0060 Insertion Tool: T1866 Pins: S 10 in gold (min) over Ni S 50 in gold (min) over Ni Sockets: S 50 in gold (min) over Ni on mating surface, Contactgold Resistance flash over Ni Extraction termination Force S1) s: Guide Holes in position 1 and 32 S2) s: Guide Pins in position 1 and 32 S3) For ordering information regarding modules assembled in frames,, see page pgs. 4/18. L 20 S4) Dimensions in inches (mm) S5) If assembling the modules into a frame, two YHD0027 clips are required per module Extraction Force Contact Life Cycles Breakdown voltage Dielectric Withstanding Voltage Insulation Resistance Temperature Rating Insulator Contact Material: (pin) (socket) 4amps < 5 milliohms.5--2 oz. >100,000 2200 VAC 1650V VAC 5x10 9 ohms min. @ 500 VDC -- 55C to + 125C PPS Brass BeCu wires + brass body Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com 4 / 9
L SERIES MULES Module V Coax H Width: 1.5 Units H Contacts: 3 Hypertac R Contacts (on both signal & ground) H Can be mounted by itself or in a frame Gender Termination Part Number Replacement Contacts.441 (11.20) Crimp Coaxial for RG316 Crimp Coaxial for RG316DB LVFRTAH LVFR1TAH YCX0315--002AH YCX0315--019AH.201 (5.10) Solder Coaxial for RG405 or T--Flex 405 LVFSTAH YCX0315--001AH.291 (7.38).129 (3.27) Crimp Coaxial for RG316 Crimp Coaxial for RG316DB LVMRTH LVMR1TAH YCX0315--004H YCX0315--018H.291 (7.38) Solder Coaxial for RG405 or T--Flex 405 LVMSTH YCX0315--003H ACCESSORIES For Inner Conductor Crimping Crimp tool: AFM8 Positioner: T1957 For Outer Conductor Crimping Crimp tool: HX3 Die Set: T1958 or T2019 for RG316DB Contact Removal Tool: T1982 Cabling Instructions Crimp (R) & (R1) Solder (S) Cable RG316 & RG405 T--Flex 405 RG316DB Socket S50302 S50301 S50307 Pin S50304 S50303 S50308 Please request specs from our Customer Service Department File No.: UL E102195 General Specifications COAXTACt Nominal Impedance 50 ohms Frequency Range DC 3 GHz with RG316 DC 18GHz with RG405 Temperature Rating --55C to125c Materials Brass, Beryllium Copper PTFE Fluorocarbon Finishes Center Contacts and over nickel Housings over copper Wire over nickel Electrical (Based on RG--405 Semi Rigid Cable) VoltageStandingWaveRatio (DCto3GHz)1.20:1max. (3GHz to 18GHz) 1.50:1 max. RF Transmission Loss 0.50 db @ 18 GHz Insulation Resistance 5,000 megohms min. Dielectric Withstanding Voltage 500 VRMS Inner Contact 8 miliohms max. Outer Contact 2 milliohms max. Mechanical Extraction force 1.5 -- 6.0 oz max., 3 oz. average Connector Durability Greater than 25,000 cycles S For ordering information regarding modules assembled in frames, see pg. L20 S Dimensions in inches (mm) S Contact shipped unassembled 1) 2) 3), see page 4/18. 4 / 10 Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com
L SERIES MULES Module V 25 Amp Power H Width: 1.5 Units H Can be mounted by itself or in a frame H Contacts: 3 Hypertac R Contacts Gender Termination Part Number Replacement Contacts.439 (11.15) Crimp 25 Amps (Free Air) (17 Amps (Bundled) 12--14 12-14 AWG LVFP1TAH YSK025--031AH.551 (14.00).276 (7.00) 1.140 (28.95).325 (8.25).514 (13.05) Empty Block ZLV003--001 (LVFHT).197 (5.00).906 (23.00).104 2.65).514 (13.05).906 (23.00).197 (5.00) 1.140 (28.95).104 2.65).551 (14.00).276 (7.00).325 (8.25) Empty Block ZLV003--002 (LVMHT) Plating Reference Crimp tool: Extraction Tool: Positioner:.295 (7.48).122 (3.11) Pins: S 10 in gold (min) over Ni S 50 in gold (min) over Ni Sockets: S 50 in gold (min) over Ni on mating surface, Contactgold Resistance flash over Ni Extraction termination Force ACCESSORIES M309 T1982 T1981 File No.: UL E102195 Crimp 25 25 Amps Amp (FreeAir) 17 Amps (17 Amps (Bundled) Bundled) 12-14 AWG 12--14 AWG S For ordering information regarding modules assembled in frames, see pg. L20 S Dimensions in inches (mm) S Contact shipped unassembled 1) 2) 3), see page 4/18. LVMP1TH YPN025--24H YPN025-024H 25 amps (Free Air) 17 Amps (Bundled) (Bundled) (milliohms) <1.5 milliohms Extraction Force 3.0 -- 17.0 oz. Contact Life Cycles >100,000 Breakdown voltage >1600 VRMS Dielectric Withstanding Voltage 1200 VRMS Insulation Resistance >10 4 megohms @ 500VDC Temperature Rating --55 deg. C to + 105 deg. C Insulator Nylon Contact material: BeCu wires + brass Approx. Weight: M:.32 oz. (9.15g), F:.34 oz. (9.50g) Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com 4 / 11
L SERIES MULES Module G 200 Amp Contact Rating Width is 3.5 units 1 Hypertac removable crimp contact.239 (6.08mm) contact File no. E102195 File no. LR83002 1.142 (29.00) Module K 1.590 (40.40).994 (25.25).239 (6.08).758 (19.25) Recommended for LEH & LPH Frames Only 100 Amp Contact Rating 1.395 (35.45).787 (20.00) Width is 2.5 units 1 Hypertac removable crimp contact.169 (4.30mm) contact File no. E102195 File no. LR83002 2.362 (60.00) INSULATORS Width Break Down Voltage Dielectric Withstanding Voltage: Insulation Resistance Insulator Material CONTACTS Life Cycle Diameter Resistance Extraction Force Material: Pin Socket Plating Reference Reference L (Strip length): Barrel I.D.: Conductor Size Replacement Pins Replacement Sockets ACCESSORIES Crimp Tool: Mounting bracket: Extraction tool: Positioner: TYPE G 3.5 units >1500V RMS 1100 V RMS >10 6 megohms @500 VDC Polyphthalamide >100,000 cycles.239 (6.08) 2004 amperes <.20 milliohms 80 -- 160 oz. TYPE K 2.5 units.169 (4.30) 100 amperes <.35 milliohms 15 -- 90 oz. Copper BeCu wires; copper rear tail; brass body TI = 30 in (min) gold over Ni (pin only) TAH = 50 in (min) gold over Ni on mating surface, gold flash over Ni on termination (sockets only).709 (18.00).445 (11.30) #1/0AWG YPN0612--021RI YSK0612--015AH T1501 T1551 T1500 T1536.591 (15.00).283 (7.20) #4 AWG YPN043--016RI YSK043--010AH T1501 T1551 T1507 T1535 1.142 (29.00).169 (4.30) 1.930 (49.00).541 (13.75) L K F R TAH Plating: TI, TAH Omit for empty insulator Terminal Style: R (crimp) Omit for empty insulator Contact Gender: M =, F =, MULE AVAILABILITY: Standard Modules Type of Module: K (100 amps), G (200 amps) Recommended for LEH & LPH Frames Only 1) Dimensions in inches (mm) 2) Contacts shipped unassembled 3) Approved to 180 amps by CSA for 30 C temperature rise 4) For ordering information regarding modules assembled in frames, see pg. 4/18. 4 / 12 Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com
L SERIES FRAMES FRAME H Plug.220 (5.60) 1.22 1.177 (3.10) (31.0) (29.90).590 (15.00) Plus Y Y 1.26 (32.00) 1.177 (30.00).165 (4.20) Rack and panel with guides Float mounting.049 (1.25mm) 4 max File no. E102195 File no. LR83002 Also mates with the JH Frame L E H 4 Frame Size: 4 -- 20 units P = Plug, E = Receptacle FRAME AVAILABILITY: Frame Sizes 6, 10, 16, 20 QUICKEST DELIVERY Other Whole Unit Frames Sizes 4--19 STANDARD 1/2 Unit Frame Sizes AVAILABLE OPTION (Consult Factory) Frame Sizes 21--30 AVAILABLE OPTION (Consult Factory) Receptacle.591 (15.00) Y.590 (15.00) Plus Y Weight, excluding modules Plug 1.9 oz. (53.2 gm) @ 4 units 2.8 oz. (78.8 gm) @ 20 units Receptacle 1.6 oz. (45.2 gm) @ 4 units 2.5 oz. (70.8 gm) @ 20 units 1.417 (36.00).039 (1.00) 1) See mounting dimensions, pg. L19 2) See ordering information, page pg. L20 4/18. for complete connectors 3) Dimensions in inches (mm) 4) Available option:.125 float. (use modification 398). Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com 4 / 13
L SERIES FRAMES FRAMES MY & MV (Plastic Backshells) H 180_ quick turn or standard multi--turn H Up to 300 signal contacts H Adjustable cable clamp: H >5,000 mating cycles H 36 possible keying combinations.452 to 1.260 in. (11.5 to 32.0 mm) H Rugged black polycarbonate backshell H Built--in pin protection H 12,15,20 & 22 unit lengths LPMY (1/2 Turn Plug) LPMV (Multi -Turn Plug) 1.677 (42.60).984 (25.00) 1.016 (25.80) 1.677 (42.60).984 (25.00).776 (19.70) 2.756 (70.00) 3.939 (100.05) 2.185 (55.50).3.906 (99.20) 2.756 (70.00) 2.185 (55.50).528 (13.40) C.528 (13.40) C A 1.42 (36.00) B A 2 5 4 1 1.614 (41.00) 1.614 (41.00) E D 2.60 (66.00) VIEW OF MATING FACE VIEW OF MATING FACE LEMY (Receptacle for 1/2 Turn) B LEMV (Receptacle for Multi -Turn) B.400 (10.16) 1.480 (37.60) 1.260 (32.00) A E B D 1 2 5 4 1.4800 (37.60) 1.260 (32.00) A B E D 1 2 5 4 VIEW OF MATING FACE.374 (9.50).400 (10.16) VIEW OF MATING FACE.374 (9.50) M3.0 (9.90).870 (22.10) L P MY 12 Frame Size: 12 15, 20 & 22 units (allow 2 units for jackscrew) Y =1/2 Turn, V = Multi--Turn P = Plug, E = Receptacle FRAME AVAILABILITY: LEMY22, LPMY22 QUICKEST DELIVERY LEMY, LPMY Frame Sizes 12, 15, 20 STANDARD LEMV, LPMV Frame Sizes 12, 15, 20, 22 STANDARD LPMMY Frame Sizes 12, 15, 20, 22 AVAILABLE OPTION Number of Units 12 15 20 22 Dimensions A B 2.598 (66.00) 3.110 (79.00) 3.248 (82.50) 3.760 (95.50) 4.331 (110.00) 4.843 (123.00) 4.764 (121.00) 5.276 (134.00) 2 C 3.315 (84.20) 3.965 (100.70) 5.047 (128.20) 5.480 (139.20) 1) See pg. L19 4/17 & L20 4/18 for mounting dimensions and ordering information for complete connectors. 2) Dimensions in inches (mm) 3) Tolerance is 0.020 (0.50mm) 4) Tolerance is 0.040 (1.0mm) 5) 1/2 Turn plug frame without hood available as LPMMY 4 / 14 Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com
L SERIES FRAMES FRAMES A, B and BV H Guides and Jack Screw Available Frame A Simple Rack and Panel Frame B Simple Rack and Panel with Guides Frame BV Rack and Panel with Guides & Jackscrew.472 (12.00) Plug.295 (7.50) Plug.295 (7.50).334 (8.50) Plug 3.906 (99.20).492 (12.50).492 (12.50).472 (12.00) 1.417 (36.00) 1.260 (32.00).295 (7.50) Receptacle L E A 4.236 (6.00).472 (12.00).472 (12.00) 1.417 (36.00) 1.260 (32.00) Frame Size: 4 -- 20 units Frame A, B or BV P = Plug, E = Receptacle Receptacle.236 (6.00) FRAME AVAILABILITY: A, B, BV Frame Sizes 4--20 STANDARD A, B, BV Frame Sizes in Half Units AVAILABLE OPTION.492 (12.50) 1.417 (36.00).236 (6.00).295 (7.50).334 (8.50) Receptacle Weight, excluding modules A and B Plug 1 oz. (28.2 gm) @ 4 units 1.9 oz. (53.8 gm) @ 20 units A and B Receptacle 1 oz. (28.2 gm) @ 4 units 1.9 oz. (53.8 gm) @ 20 units BV Plug 4.7 oz. (133.2 gm) @ 4 units 5.6 oz. (158.8 gm) @ 20 units BV Receptacle 2.5 oz. (70.4 gm) @ 4 units 3.4 oz. (96.0 gm) @ 20 units.935 (23.75) 1) S See mounting dimensions, pg. 4/17. L19 2) S See ordering information, pg. 4/18. L20 for complete connectors 3) S Dimensions in inches (mm) Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com 4 / 15
L SERIES FRAMES FRAME J (Metal Backshell) Hooded connector with round cable clamp Alternate cable clamp locations available Plug.492 (12.50) 2.087 (53.00) Weight, excluding modules Plug 3.5 oz. (99.0 gm) @ 4 units 5.5 oz. (156.6 gm) @ 20 units Receptacle 1.2 oz. (32.8 gm) @ 4 units 2.1 oz. (58.4) gm) @ 20 units 1.417 (36.00).236 (6.00) L P J 14 4 SC10 Note: FRAME JV Cable clamp: SC10, SC15, SC20, SC24 (see pg. L118) 20) not applicable on receptacle Frame Size: 4 -- 20 units P = Plug, E = Receptacle S Plugs with flat cable clamp available. Replace J in part number with K and cable clamp callout to SC33 (33mm) or SC50 (50mm). S Plugs without cable clamp available. Replace J in part number with R and remove SC cable clamp callout. FRAME AVAILABILITY: Frame Sizes 4--20 STANDARD 1/2 Unit Frame Sizes AVAILABLE OPTION (Consult Factory) (Metal Backshell) Hooded connector with round cable clamp Side and double openings also available on special order Jackscrew extraction Plug Receptacle Weight, excluding modules Plug 1.9 oz. (53.2 gm) @ 4 units 2.8 oz. (78.8 gm) @ 20 units Receptacle 1.6 oz (45.2 gm) @ 4 units 2.5 oz. (70.8 gm) @ 20 units.334 (8.50) 3.906 99.20) 1.260 (32.30).472 (12.00).787 (20.00).492 (12.50).236 (6.00).492 (12.50) 2.087 (53.00) 1.417 (36.00) L P JV 6 SC10 Note: Cable clamp: SC10, SC15, SC20, SC24 (see pg. L118) 20) not applicable on receptacle Frame Size: 4 -- 20 units P = Plug, E = Receptacle Receptacle S Plugs with flat cable clamp available. Replace J in part number with K and cable clamp callout to SC33 (33mm) or SC50 (50mm). S Plugs without cable clamp available. Replace J in part number with R and remove SC cable clamp callout. FRAME AVAILABILITY: Frame Sizes 4--20 STANDARD 1/2 Unit Frame Sizes AVAILABLE OPTION (Consult Factory).935 (23.75) 1.260 (32.30).472 (12.00).492 (12.50).295 (7.50) S See mounting dimensions, pg. 4/17 L19 S See ordering information, pg. 4/18 L20 for complete connectors S Dimensions in inches (mm) 1) 2) 3) 4 / 16 Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com
MOUNTING DIMENSIONS For Frame Types: A, B, BV, J, JV, K, KV, R & RV L SERIES L SERIES FRAMES.226 (5.75) STATIONARY STATIONARY WITH JACKSCREW EXTRACTION 3 Alternate Mounting Dimensions for Receptacles to Provide Clearance for Jackscrew Base Hold Down Clamps.207.472 Note 3.126 Note 3 Note 3 (5.25) (12.00) (3.20) 4 Holes.795 (20.20).886 (22.50) X X X.116 (3.00) X.167 (4.25) Plug.116 (3.00) 1.220 (31.00).116 (3.00) For Frame Type H (float mounting) Receptacle.059 (1.50) 1.220 (31.00) Min..116 (3.00) Note 3.161 (4.10) R.197 (5.00) Max. Optional Y 1.457 (37.00).197 (5.00).197 (5.00).161 (4.10) R.197 (5.00) Max. Optional MOUNTING DIMENSIONS 2 Y.591 (15.00).197 (5.00) 1.457 (37.00) Units X Y 1 2 3 4 5 6 7 8 9 10.236.452.669.886 1.102 1.319 1.535 1.752 1.969 2.185 (6.00) (11.50) (17.00) (22.50) (28.00) (33.50) (39.00) (44.50) (50.00) (55.50) 1.319 1.535 1.752 1.969 2.185 2.402 2.618 2.835 3.051 3.268 (33.50) (39.00) (44.50) (50.00) (55.50) (61.00) (66.50) (72.00) (77.50) (83.00) Units X Y 11 12 13 14 15 16 17 18 19 20 2.402 2.618 2.834 3.051 3.268 3.484 3.700 3.917 4.134 4.350 (61.00) (66.50) (72.00) (77.50) (83.00) (88.50) (94.00) (99.50) (105.00) (110.50) 3.484 3.701 3.917 4.134 4.350 4.567 4.784 5.000 5.217 5 (88.50) (94.00) (99.50) (105.00) (110.50) (116.00) (121.50) (127.00) (132.50) (138.00) Units X Y 1) 59 in. oz. (4.2 cm--kg) torque for mounting. 2) Dimensions in inches (mm). 3).010 (.25) maximum radius typical. 21 22 23 24 25 26 27 28 29 30 4.567 4.783 5.000 5.216 5 5.649 5.865 6.082 6.299 6.515 (116.00) (121.50) (127.00) (132.50) (138.00) (143.50) (149.00) (154.50) (160.00) (165.50) 5.650 5 6.083 6.299 6.516 6.732 6.949 7.165 7.382 7.598 (143.50) (149.00) (154.50) (160.00) (165.50) (171.00) (176.50) (182.00) (187.50) (193.00) Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com 4 / 17
L SERIES.400 (10.16).138 (3.50) Required for MY Only 1.220 (31.00) Receptacle MOUNTING DIMENSIONS 3 For Frame Types: MV and MY Dimension A plus.020 (.50) R.010 (.25) Max.472 (12.00).126 (3.20).886 (22.50) Number of Units 12 15 20 22 Dimensions A 2.598 (66.00) 3.248 (82.50) 4.331 (110.00) 4.764 (121.00) The L series connectors are engineered for quick and easy use. Standard frames will be shipped completely assembled with the modules you select mounted. 1 The length of the frame is computed by multiplying the module units by the module quantity and totaling the results. If 1/2 unit spacers are required order (LFH1) (Delete L in assembly part number) LPJ8/4AMST/2CHT/ TG SC15 L P=Plug E = Receptacle Frame type: A, B, BV, BY, H, J, JV, JY, MV, MY, MMY, K, KV, KY,R,RV,&RY Length of Frames 4-20 2 Units. Allow 2 additional units when ordering frames with jackscrews (BV, JV, KV,MV,MY,RV)(upto 30 units are available, consult factory) Cable clamp location (J and JV Frames Only): L = Left R = Right F = Front B=Back Omit for default location: J and JV Frames = top K and KV Frames = front MV and MY Frames = As shown only Cable clamp & cable size: 4 Round cable (J & JV Frames) Max. dia. Min. dia. 10 =.394 (10.0).210(5.35) 15 =.590 (15.0).385 (9.75) 20 =.787 (20.0).605 (15.25) 24 =.945 (24.0).670 (17.0) Number of Modules Module combination by quantity (Refer to catalog page -- for type of module and terminals style etc. using above outline as sample only) Module will be positioned in frame according to sequence listed. Modules R, S & U can be combined with other module types using special adaptors (consult factory). 1) When part number exceeds 24 characters, a special abbreviated part number will be assigned at the time of order. 2) Frames MV and MY available in 12, 15, 20 & 22 units only. 3) Dimensions in inches (mm) 4) There may be some limitations on cable clamp sizes in the shorter length connectors (Consult Factory). Plating: TG = 10 in gold (min) over Ni TH = 50 in gold (min) over Ni TAH = 50 in gold (min) over Ni on mating surface, gold flash over Ni on termination. This represents plating for all the modules in the connector. When mixing platings consult factory. 4 / 18 Hypertronics Corporation Toll Free: 1-800-225-9228 Tel: 978-568-0451 Fax: 978-568-0680 www.hypertronics.com