Maestro Wireless Dimmers and Switches The Maestro Wireless solution incpates Maestro Wireless load controls, wireless senss, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr SavrTM senss and Pico wireless controls f light control and general switched loads. Features The Maestro Wireless solution provides dimming/ switching of multiple load types, occupancy/vacancy sensing, daylight harvesting, and high-end trim. Lutron patented Clear Connect RF Technology wks through walls and flos. Incpates advanced features such as fade ON/fade OFF, high-end trim, and rapid full-on. Controls include Front Accessible Service Switch (FASSTM) f safe lamp replacement. Two-wire dimmers and switches available f retrofit applications. Power failure memy: If power is interrupted, the control will return to its previously set level pri to interruption. Receiving Devices Maestro Wireless Controls and Non- Dimmers Lamp Dimmers Transmitting Devices Radio Powr SavrTM Senss and Non- Switches Plug-In Modules 694m 09.8. Ceiling-Mounted Occupancy and Vacancy Senss Pico Wireless Controls Wall-Mounted Occupancy and Vacancy Senss Daylight Modules
Maestro Wireless Dimmers Models Available Dimmers CFL/LED/Halogen / Incandescent / Magnetic Low-Voltage MRF-6CL-XX 50 W CFL/LED Dimmer; 600 W Incandescent/Halogen 0 V~ MRF-6MLV-XX 600 W / 600 VA Incandescent/MLV Dimmer 0 V~ MRF-6ND-0-XX* 600 W / 600 VA Spec-Grade wire Dimmer 0 V~ MRF-0D-0-XX 000 W /000 VA Spec-Grade Dimmer 0 V~ -Wire Fluescent MRF-F6AN-DV-XX* 6 A -wire Fluescent Spec-Grade -Wire Dimmer 0 77 V~ Electronic Low-Voltage Dimmer MRF-6ELV-0-XX* 600 W ELV Dimmer 0 V~ * wire required Dimmer 694m 09.8. Companion Dimmers Claro Gloss Finishes MA-R-XX Companion Dimmer 0 V~ MA-R-77-XX Companion Dimmer 77 V~ Satin Cols Satin Finishes MSC-AD-XX Companion Dimmer 0 V~ MSC-AD-77-XX Companion Dimmer 77 V~ Companion Dimmer XX in the model number represents col/finish code.
Ganging and Derating 694m 09.8. When combining controls in the same wallbox, derating is required (see Type and Capacity tables). Only MRF-8ANS controls have fins that need to be removed f multigang installations. No other controls have fins, but they must still be derated in multigang installations. Dimmer Type and Capacity Do not remove outside fins on ends of ganged controls (shaded areas below) Required A B B B C B Maximum Control Voltage Type Minimum A: Not Ganged B: End of Gang C: Middle of Gang Incandescent 5 W 600 W 500 W 400 W MRF-6ND-0,, 0 V~ MLV 5 W / VA 450 W / 600 VA 400 W / 500 VA 00 W / 400 VA MRF-6ELV, 0 V~ ELV 5 W 600 W 500 W 400 W MRF-F6AN-DV,4 0 77 V~ Lighting ballast 0.05 A 6 A 5 A A No Required A B B B C B Maximum Control Voltage Type Minimum A: Not Ganged B: End of Gang C: Middle of Gang MRF-6CL 0 V~ Incandescent, CLF/LED 50 (see W lamp list) See Mixing Lamp Types, page 4 MRF-6MLV,,4 0 V~ MLV 50 VA 450 W / 600 VA 400 W / 500 VA 00 W / 400 VA Incandescent 50 W 000 W 800 W 650 W MRF-0D-0,,4 0 V~ MLV 50 W / VA 800 W /000 VA 600 W / 800 VA 500 W / 650 VA Dimmer Type: MRF-6ND-0, MRF-6MLV, and MRF-0D-0 are designed f use with permanently-installed incandescent, magnetic low-voltage, tungsten halogen only. MRF-6ELV is designed f use with permanently-installed electronic low-voltage only. Do not install dimmers to control receptacles mot-operated appliances. MRF-F6AN-DV is designed f use with permanently installed -wire line voltage control fluescent ballasts LED drivers only (Hi-lume, Hi-lume Compact SETM, Eco-0, and EcoSystem ). MRF-6CL is designed f use with permanently-installed incandescent, CFL, LED, tungsten halogen only. Low-Voltage Applications: Use MRF-6ND-0, MRF-6MLV, and MRF-0D-0 with magnetic (ce and coil) low-voltage transfmers only. Not f use with electronic (solid-state) low-voltage transfmers. Use MRF-6ELV with electronic (solid-state) low-voltage transfmers only. Operation of a low-voltage circuit with lamps inoperative removed may result in transfmer overheating and premature failure. Lutron strongly recommends the following: Do not operate low-voltage circuits without operative lamps in place. Replace burned-out lamps as quickly as possible. Use transfmers that incpate thermal protection fused transfmer primary windings to prevent transfmer failure due to overcurrent. Can control the following power booster/load interface: Hi-Power 4 6TM Boosters (HP-, HP-4, HP-6) f control of most popular lighting sources including Lutron -wire line-voltage control fluescent dimming ballasts (Hi-lume, Hi-lume Compact SETM, Eco-0, and EcoSystem ). 4 Can control the following power boosters / load interfaces: Phase-adaptive Power Modules (PHPM-WBX-DV-WH), -wire Fluescent Power Modules (PHPM-F-DV-WH), Tu-Wire Fluescent Power Modules (PHPM-PA-DV-WH), and 0 0 V (GRX-TVI).
Dimmer Type and Capacity (continued) Mixing Lamp Types Mixing lamp types (using a combination of CFL/LED, and Incandescent/Halogen bulbs) and ganging with other dimmers electronic switches may reduce maximum wattage, as shown. Example: If fins from one side of dimmer are removed and you have two 4 W bulbs installed (total CFL Wattage = 48 W), you may add up to 00 W of incandescent halogen lighting. Total CFL/LED Wattage 694m 4 09.8. Do not remove outside fins on ends of ganged controls (shaded areas below) A B B B C B Total Incandescent/Halogen Wattage A: Not Ganged B: End of Gang C: Middle of Gang MRF-6CL 0 W + 50 W 600 W Or 50 W 500 W Or 50 W 400 W W 5 W + 0 W 500 W Or 0 W 400 W Or 0 W 00 W 6 W 50 W + 0 W 400 W Or 0 W 00 W Or 0 W 00 W 5 W 75 W + 0 W 00 W Or 0 W 00 W Or 0 W 00 W 76 W 00 W + 0 W 00 W Or 0 W 00 W Or 0 W 50 W 0 W 5 W + 0 W 00 W Or 0 W 50 W Or 0 W 6 W 50 W + 0 W Or 0 W Or 0 W 4
Maestro Wireless Switches Models Available Switches Lighting and mot loads MRF-6ANS-XX* 6 A Lighting/ A Fan (/0 HP mot), Electronic Switch 0 V~ MRF-8ANS-0-XX* 8 A Lighting, 5.8 A Fan (/4 HP mot), Spec-Grade Electronic Switch 0 V~ MRF-6ANS-77-XX* 6 A Lighting, Spec-Grade Electronic Switch 77 V~ MRF-8S-DV-XX 8 A Lighting, A Fan (/0 HP mot, 0 V~ only), Spec-Grade Electronic Switch 0 77 V~, no neutral wire required * wire required Switch 694m 5 09.8. Companion Switches Claro Gloss Finishes MA-AS-XX Companion Switch 0 V~ MA-AS-77-XX Companion Switch 77 V~ Satin Cols Satin Finishes MSC-AS-XX Companion Switch 0 V~ MSC-AS-77-XX Companion Switch 77 V~ Companion Switch XX in the model number represents col/finish code. 5
Switch Type and Capacity 694m 6 09.8. Do not remove outside fins on ends of ganged controls (shaded areas below) Required A B B B C B Control Voltage Type Minimum Maximum A: Not Ganged B: End of Gang C: Middle of Gang MRF-8ANS-0, 0 V~ Lighting 5 W 8 A 6.5 A 5 A Fan Mot 0. A /4 HP (5.8 A) /4 HP (5.8 A) /6 HP (4.4 A) MRF-6ANS 0 V~ Lighting 5 W 6 A 5 A.5 A Fan Mot 0. A /0 HP ( A) /0 HP ( A) /0 HP ( A) MRF-6ANS-77 77 V~ Lighting 5 W 6 A 5 A.5 A No Required A B B B C B Maximum Control Voltage Type Minimum A: Not Ganged B: End of Gang C: Middle of Gang 0 77 V~ Incandescent/Halogen 5 W 8 A 8 A / 7 A 4 7 A MRF-8S-DV 0 77 V~ Fluescent/LED/CFL 40 W (LUT-MLC) 8 A 8 A / 7 A 4 7 A 0 V~ Fan Mot 0.4 A /0 HP ( A) /0 HP ( A) /0 HP ( A) Switch Type: MRF-8ANS-0 is designed f use with permanently-installed lighting loads and with fan mot loads up to /4 HP (5.8 A). MRF-6ANS is designed f use with permanently-installed lighting loads and with fan mot loads up to /0 HP ( A). MRF-6ANS-77 and MRF-8S-DV are designed f use with permanently-installed lighting loads. MRF-8S-DV is designed f use with permanently-installed lighting loads and with fan mot loads up to /0 HP ( A, 0 V~ only). F loads larger than 8 A (0 V~), the MRF-8ANS-0 switch can be used with the PHPM-SW-DV-WH power booster. F loads larger than the MRF-6ANS-77 capacity of 6 A (77 V~), the MRF-8ANS-0 can also be used with the PHPM-SW-DV-WH power booster to switch 77 V~ loads. Please note that in this application, the MRF-8ANS-0 switch is providing an input at 0 V~ and the power booster is switching 77 V~. The LUT-MLC ensures proper function with certain fluescent, CFL, and LED load types. 4 Maximum load f double-gang application is 8 A. Triple-gang application derates maximum load to 7 A. 6
Specifications Regulaty Approvals UL Listed. cul Listed (MRF-6CL only). CSA Certified (except f MRF-6CL). FCC Approved. Complies with the limits f a Class B digital device, pursuant to Part 5 of the FCC Rules. Industry Canada Certified. Power Operating voltage: 0 V~ 50/60 Hz (all models) 77 V~ 50/60 Hz (MRF-6ANS-77, MRF-8S-DV, MRF-F6AN-DV) Key Design Features Dimmers On a single-tap, lights fade UP DOWN. On a double-tap, lights go to full ON. When ON, press and hold to engage 0-second fade to OFF. Light levels can be fine-tuned by pressing and holding the dimming rocker until the desired light level is reached. Two-wire dimmers available. Switches On a single-tap, lights turn ON OFF. Two-wire switches available. All Tested to withstand electrostatic discharge without damage memy loss, in accdance with IEC 6000-4-. Tested to withstand surge voltages without damage loss of operation, in accdance with IEEE C6.4-99 Recommended Practice on Surge Voltages in Low-Voltage AC Power Circuits. Controls always operate locally and do not require system control. Power failure memy: should power be interrupted, the control will return to its previously-set level pri to the interruption when power is rested. Uses conventional -way and 4-way wiring. 694m 7 09.8. Multiple location control from Dimmer/Switch and up to nine Companion Dimmers/Switches. Use Lutron Designer (Claro and Satin Cols ) wallplates designer-style wallplates from other manufacturers. Wallplates are sold separately. Lutron Claro and Satin Cols wallplates snap on with no visible means of attachment. Requires a one-gang U.S. wallbox; in (89 mm) deep recommended, 4 in (57 mm) deep minimum. indicat lights. System Communications and Capacity Maestro Wireless controls communicate with the Pico wireless controls and Radio Power SavrTM senss through radio frequency (RF). Maestro Wireless local controls must be located within 60 ft (8 m) line-of-sight 0 ft (9 m) through walls, of Radio Power SavrTM senss. Maestro Wireless local controls must be located within 00 ft (0 m) line-of-sight 0 ft (9 m) through walls, of a Pico wireless control. Up to ten Maestro Wireless controls can be configured to wk together. Environment Ambient operating temperature: F to 04 F (0 C to 40 C), 0% 90% humidity, non-condensing. Indo use only. 7
Dimensions All dimensions are shown as: in (mm) 694m 8 09.8. Front View Side View 4 6 (9) 5 6 (75) 5/6 (8) 8 (0) Mounting Control Mounting Screws Adapter Mounting Screws Wallbox Control Wallplate Adapter Wallplate Wallplate Adapter / Wallplate purchased separately 8
Operation 694m 9 09.8. Dimmer Status LEDs Indicate light level; glow softly as night light when light is OFF Switch Status LED Indicates load status; glows softly as night light when light is OFF Dimming Rocker Press to brighten Press to dim Tapswitch Tap ON / OFF Tapswitch Tap ON / OFF; Double-tap: lights go to full ON FASSTM Front Accessible Service Switch FASSTM Front Accessible Service Switch FASSTM Front Accessible Service Switch Imptant Notice: To service load, remove power by pulling the FASSTM switch out completely on either the Dimmer / Switch Companion Dimmer / Switch. After servicing load, push the FASSTM switch back in fully to reste power to the control. 9
Wiring Diagrams Single-Location Dimmer Installation without MRF-6CL, -6MLV, -0D-0 Dimmer 694m 0 09.8. Multi-Location Dimmer Installation without MRF-6CL, -6MLV, -0D-0 with MA-R / MSC-AD Companion Dimmer Companion Dimmer Dimmer When using controls in single location installations, tighten the blue terminal without any wires attached. Do not connect the blue terminal to any other wiring to ground. Up to nine Maestro Companion Dimmers may be connected to the Maestro Wireless Dimmer. Total blue terminal wire length may be up to 50 ft (76 m). 0
Wiring Diagrams (continued) 694m 09.8. Single-Location Dimmer/Switch Installation with MRF-6ND-0, -6ELV-0, -6ANS-0, -8ANS-0, -6ANS-77 Dimmer/Switch 0 V~ 60 Hz 77 V~ 60 Hz Multi-Location Dimmer/Switch Installation with,4 MRF-6ND-0, -6ELV-0 with MA-R/MSC-AD; -6ANS-0, -8ANS-0 with MA-AS/MSC-AS; -6ANS-77 with MA-AS-77/MSC-AS-77 5 Companion Dimmer/Switch Companion Dimmer/Switch Dimmer/Switch 0 V~ 60 Hz 77 V~ 60 Hz When using controls in single location installations, tighten the blue terminal without any wires attached. Do not connect the blue terminal to any other wiring to ground. 0 V~: MRF-6ND, -6ANS-0, -8ANS-0, -6ELV-0; 77 V~: MRF-6ANS-77, -8S-DV. Up to nine Maestro Companion Dimmers / Switches may be connected to the Maestro Wireless Dimmer / Switch. Total blue terminal wire length may be up to 50 ft (76 m). 4 -wire Dimmers / Switches must be connected on the side of a multi-location installation. 5 Requires MA-AS / MSC-AS f 0 V~ applications, and MA-AS-77 / MSC-AS-77 f 77 V~ applications.
Wiring Diagrams (continued) Single-Location Switch Installation with LUT-MLC MRF-8S-DV Switch 694m 09.8. 0 V~ 60 Hz 77 V~ 60 Hz Optional LUT-MLC Multi-Location Switch Installation with LUT-MLC,,4 MRF-8S-DV with MA-AS / MA-AS-77 MSC-AS / MSC-AS-77 5 Companion Switch Companion Switch Switch Optional 0 V~ 60 Hz 77 V~ 60 Hz LUT-MLC A LUT-MLC ensures proper function when fluescent, CFL, LED loads are used. Install the LUT-MLC inside a load fixture in a separate J-box within the circuit. When using controls in single-location installations, tighten the blue terminal without any wires attached. Do not connect the blue terminal to any other wiring to ground. 0 V~: MRF-6ND, -6ANS-0, -8ANS-0, -6ELV-0; 77 V~: MRF-6ANS-77, -8S-DV. 4 Up to nine Maestro Companion Switches may be connected to the Maestro Wireless Switch. Total blue terminal wire length may be up to 50 ft (76 m). 5 Requires MA-AS / MSC-AS f 0 V~ applications, and MA-AS-77 / MSC-AS-77 f 77 V~ applications.
Wiring Diagrams (continued) 694m 09.8. Single-Location Fluescent Dimmer Installation with MRF-F6AN-DV Dimmer White Lutron Ballast/Driver 77 V~ 60 Hz White Lutron Ballast/Driver Multi-Location Fluescent Dimmer Installation with, MRF-F6AN-DV with MA-R / MA-R-77 MSC-AD / MSC-AD-77 4 Companion Dimmer Companion Dimmer Dimmer White Lutron Ballast/Driver 77 V~ 60 Hz White Lutron Ballast/Driver When using controls in single location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring to ground. Up to nine Maestro Companion Dimmers may be connected to the Maestro Wireless Dimmer. Total blue terminal wire length may be up to 50 ft (76 m). -wire Dimmers must be connected on the side of a multi-location installation. 4 Requires MA-R / MSC-AD f 0 V~ applications, and MA-R-77 / MSC-AD-77 f 77 V~ applications.
Wiring Diagrams (continued) 694m 4 09.8. Single-Location Switch Installation with Power Booster Single Feed MRF-6ANS-0, -8ANS-0 with PHPM-SW-DV-WH Switch Zone In Switched Hot Multi-Location Switch Installation with Power Booster Single Feed, MRF-6ANS-0, -8ANS-0 with MA-AS / MSC-AS and PHPM-SW-DV-WH Companion Switch Switch Zone In Switched Hot When using controls in single-location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring to ground. Up to nine Maestro Companion Switches may be connected to the Maestro Wireless Switch. Total blue terminal wire length may be up to 50 ft (76 m). -wire Switches must be connected on the side of a multi-location installation. 4
Wiring Diagrams (continued) 694m 5 09.8. Single-Location Switch Installation with Power Booster Dual Feed MRF-6ANS-0, -8ANS-0 with PHPM-SW-DV-WH Switch Zone In 77 V~ 60 Hz Switched Hot Multi-Location Switch Installation with Power Booster Dual Feed, MRF-6ANS-0, -8ANS-0 with MA-AS / MSC-AS and PHPM-SW-DV-WH Companion Switch Switch Zone In 77 V~ 60 Hz Switched Hot When using controls in single-location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring to ground. Up to nine Maestro Companion Switches may be connected to the Maestro Wireless Switch. Total blue terminal wire length may be up to 50 ft (76 m). -wire Switches must be connected on the side of a multi-location installation. 5
Wiring Diagrams (continued) 694m 6 09.8. Single-Location Fluescent Dimmer Installation with Power Booster Single Feed MRF-F6AN-DV with PHPM-F-DV-WH, PHPM-PA-DV-WH, PHPM-WBX-DV-WH Dimmer 4 Zone In Dimmed Hot Multi-Location Fluescent Dimmer Installation with Power Booster Dual Feed, MRF-F6AN-DV with MA-R / MSC-AD and PHPM-F-DV-WH, PHPM-PA-DV-WH, PHPM-WBX-DV-WH Companion Dimmer Dimmer 4 Zone In Dimmed Hot When using controls in single location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring to ground. Up to nine Maestro Companion Dimmers may be connected to the Maestro Wireless Dimmer. Total blue terminal wire length may be up to 50 ft (76 m). -wire Dimmers must be connected on the side of a multi-location installation. 4 When using a PHPM, tighten the brass (Sw Hot) terminal of the MRF-F6AN-DV. Do not connect the brass terminal to any other wiring to ground. 6
Wiring Diagrams (continued) 694m 7 09.8. Single-Location Fluescent Dimmer Installation with Power Booster Dual Feed MRF-F6AN-DV with PHPM-F-DV-WH, PHPM-PA-DV-WH, PHPM-WBX-DV-WH Dimmer 4 Zone In 77 V~ 60 Hz Dimmed Hot Multi-Location Fluescent Dimmer Installation with Power Booster Dual Feed, MRF-F6AN-DV with MA-R / MSC-AD and PHPM-F-DV-WH, PHPM-PA-DV-WH, PHPM-WBX-DV-WH Companion Dimmer Dimmer 4 Zone In 77 V~ 60 Hz Dimmed Hot When using controls in single location installations, tighten the blue terminal. Do not connect the blue terminal to any other wiring to ground. Up to nine Maestro Companion Dimmers may be connected to the Maestro Wireless Dimmer. Total blue terminal wire length may be up to 50 ft (76 m). -wire Dimmers must be connected on the side of a multi-location installation. 4 When using a PHPM, tighten the brass (Sw Hot) terminal of the MRF-F6AN-DV. Do not connect the brass terminal to any other wiring to ground. 7
Cols and Finishes Gloss Finishes Satin Finishes 694m 8 09.8. White WH Ivy IV Hot HT Merlot MR Plum PL Turquoise TQ Almond AL Light Almond LA Taupe TP Eggshell ES Biscuit BI Snow SW Gray GR Brown BR Palladium PD Midnight MN Sienna SI Terracotta TC BL briar GB stone BG Mocha Stone MS Goldstone GS Due to printing limitations, cols and finishes shown cannot be guaranteed to perfectly match actual product cols. Col chip keychains are available f me precise col matching: Gloss Finishes: DG-CK- Satin Finishes: SC-CK- Desert Stone DS Stone ST Metal Finish (wallplate only) Limestone LS When using Stainless Steel wallplates, it is recommended that you der the keypad in Midnight (MN). Stainless Steel SS 8