METROLOGIC INSTRUMENTS, INC. IS6520/MS6520 Cubit Series Omnidirectionl Br Code Scnner Instlltion nd User s Guide
LOCATIONS Corporte Hedqurters North Americ Metrologic Instruments, Inc. Customer Service: 1-800-ID-METRO 90 Coles Rod Tel: 856-228-8100 Blckwood, NJ 08012-4683 Fx: 856-228-6673 Emil: info@metrologic.com Internet: www.metrologic.com Europen Hedqurters Germny, Metrologic Instruments GmbH Tel: +49 89 89019 0 Middle Est nd Afric Dornierstrsse 2 Fx: +49 89 89019 200 82178 Puchheim b. Emil: info@europe.metrologic.com Munich, Germny Germny Emil: info@de.metrologic.com Asi Spin Metrologic Eri lbéric SL Tel: +34 913 272 400 Julián Cmrillo 29, D-1 Fx: +34 913 273 829 Edificio Dipsón Emil: info@es.metrologic.com 28037 Mdrid Itly Metrologic Instruments Itli srl Tel: +39 0 51 6511978 Vi Emili 70 Fx: +39 0 51 6521337 40064 Ozzno dell Emili (BO) Emil: info@it.metrologic.com Frnce Metrologic Eri Frnce SA Tel: +33 (0) 1 48.63.78.78 69 Rue de l Belle Etoile Fx: +33 (0) 1 48.63.24.94 ZI Pris Nord II, BP 50057 Emil: info@fr.metrologic.com 95947 ROISSY CDG CEDEX United Kingdom Metrologic Instruments UK Limited Tel: +44 (0) 1256 365900 58 Tempus Business Centre Fx: +44 (0) 1256 365955 Kingsclere Rod, Bsingstoke Emil: info@uk.metrologic.com Hmpshire RG21 6XG Russi Metrologic Russi Tel: +7 095 Bolshy Novodmitrovsky 14 RU-125015 Emil: info@ru.metrologic.com Moscow Russi Singpore Metrologic Asi (Pte) Ltd Tel: 65-6842-7155 No. 8 Kki Bukit Plce Fx: 65-6842-7166 4 th Floor Emil: info@sg.metrologic.com Singpore 416186 Chin Metro (Suzhou) Technologies Co., Ltd. Tel: 86-512-62572511 221 Xing Hi Street Fx: 86-512-62571517 Suzhou Industril Prk Emil: info@cn.metrologic.com Suzhou, Chin 215021 Jpn Metrologic Jpn Co., Ltd. Tel: 81-03-3839-8511 Mtsunoy Building, 6 Floor Fx: 81-03-3839-8519 3-14-8 Higshiueno Emil: info@jp.metrologic.com Titou-Ku, Tokyo 110-0015 Jpn South Americ Brzil Metrologic do Brsil Ltd. Tel: 55-11-5182-8226 Ru d Pz 2059 Fx: 55-11-5182-8315 CEP 04713-002 Emil: info@br.metrologic.com Chácr Snto Antônio São Pulo, SP, Brsil Outside Brzil Metrologic South Americ Tel: 55-11-5182-7273 Ru d Pz 2059 Fx: 55-11-5182-7198 CEP 04713-002 Emil: info@s.metrologic.com Chácr Snto Antônio São Pulo, SP, Brsil Copyright 2003 by Metrologic Instruments, Inc. All rights reserved. No prt of this work my be reproduced, trnsmitted, or stored in ny form or by ny mens without prior written consent, except by reviewer, who my quote brief pssges in review, or provided for in the Copyright Act of 1976. Products nd brnd nmes mentioned in this document re trdemrks of their respective compnies. ii
TABLE OF CONTENTS Introduction...1 Scnner nd Accessories...2 Quick Strt...3 Instlling the IS6520-41/MS6520-41 to the Host System...4 Instlling the IS6520-47/MS6520-47 to the PC...5 Disconnecting the PowerLink Cbles from the Scnner...6 Scnner Prts...7 Mounting Holes...7 Stnds...8 Audible Indictors...9 Filure Modes...10 Visul Indictors...11 Progrmming Modes...12 Lbels...15 Mintennce...15 Optiml Low nd Close Depth of Field...16 Optiml High nd Norml Depth of Field...17 Fr Depth of Field...18 Troubleshooting Guide...19 Appendix A Design Specifictions...23 Appendix B Defult Settings...25 iii
TABLE OF CONTENTS Appendix C Scnner Pinout Connections...29 Cble Connector Configurtions...29 Appendix D Wrrnty nd Disclimer...31 Appendix E Notices...32 Appendix F Ptents...34 Index...35 iv
INTRODUCTION Metrologic's Cubit is compct, omnidirectionl br code scnner tht cn be used s presenttion scnner or s the scnning component in Originl Equipment Mnufcturer (OEM) pplictions. Incorporting the ltest in scnning technology Cubit cn scn nd decode ll stndrd br codes in ny orienttion. As n OEM product, the IS6520 is both esy to use nd instll. The IS6520 is equipped with three threded mounting holes, seril progrmming nd PowerLink quick-disconnect cbles. The modulr design of Cubit llows the unit to be tilored to meet the needs of specific ppliction. As retil scnner, the MS6520 s user-friendly mounting brcket bolts securely to the countertop or wll for fixed-mount scnning. Cubit s smll size nd ggressive scn pttern mke it idel for convenience, sporting goods, pprel nd toy/hobby stores. Furthermore, Cubit hs the option of direct connection to 5-Volt power source or plug-in the Metrologic power supply provided with the scnner. SCANNER INTERFACE 6520-41 Full RS-232C nd Light Pen Emultion 6520-47 Keybord Wedge, Stnd Alone Keybord nd RS-232C Trnsmit/Receive 1
SCANNER AND ACCESSORIES The following is list of the prts included in the IS6520/MS6520 Kit. Cubit IS6520/MS6520 - Omnidirectionl Scnning Engine Instlltion nd User s Guide* MLPN 00-02421 MetroSelect Scnner Configurtion Guide* MLPN 00-02407 or MLPN 00-02561 *Avilble for downlod on Metrologic s website, www.metrologic.com. The following items re dependent on the type of IS6520/MS6520 Kit ordered. Some items my not be included in your kit. AC to DC Power Trnsformer - Regulted 5.2 VDC @ 650 ma output. One of the following my be included: 2 120 VAC United Sttes MLPN 45-45593 220 VAC 240 VAC Continentl Europen MLPN 45-45591 220 VAC 240 VAC United Kingdom MLPN 45-45592 PowerLink Cble with built in power jck (IS6520-41/MS6520-41 only) One of the following my be included: Stndrd - MLPN 53xxx* - 2.7 m (9') coiled cord, long strin relief Or Optionl - MLPN 54xxx* - 2.1 m (7') stright cord, short strin relief *xxx specifies connection to the host Keybord Wedge Powerlink nd Adpter Cble MLPN 54-54002 Powerlink cble with 5-pin DIN femle connector nd 6-pin mini Din mle connector nd n dpter cble with 5-pin DIN mle connector nd 6-pin mini DIN femle connector. (IS650-47/MS6520-47 only) Mounting Hrdwre - Three M3 screws re included for mounting purposes. Tilt Stnd - MLPN 46-46486 Fixed Verticl Stnd - MLPN 46-46145 To order dditionl items, contct the deler, distributor or cll Metrologic's Customer Service Deprtment t 1-800-ID-METRO (1-800-436-3876).
QUICK START 1. Connect the 10-pin RJ45 mle connector into the jck on the Cubit IS6520/MS6520. You will her click when the connection is mde. 2. Connect the L-shped plug of the power supply into the power jck on the PowerLink cble. 3. Connect the power supply into n AC outlet. Mke sure the AC input requirements of the power supply mtch the AC outlet. 4. When the IS6520 is redy to scn, the green LED will turn on, the red LED will flsh nd the scnner will beep once. 5. Plce br code in front of the scnning window. The scnner will beep once nd flsh the red LED if the br code ws successfully decoded. NOTE: Cubit is shipped from the fctory progrmmed with defult settings. Refer to the MetroSelect Progrmming Guide for instructions on how to configure the scnner. 3
INSTALLING THE IS6520-41/MS6520-41 TO THE HOST SYSTEM 1. Turn off the host system. 2. Connect the 10-pin RJ45 mle connector into the jck on the Cubit IS6520/MS6520. You will her click when the connection is mde. Note: If the Cubit IS6520 is receiving power from the host system, skip to step #5. (See cution sttement below) 3. Connect the L-shped plug of the power supply into the power jck on the PowerLink cble. 4. Connect the power supply into n AC outlet. Mke sure the AC input requirements of the power supply mtch the AC outlet. 5. Connect the PowerLink cble to the proper port on the host system. 6. Turn on the host system. Note: Plugging the scnner into port on the host system does not gurntee tht scnned informtion will be communicted properly to the host system. The scnner is shipped from the fctory progrmmed with defult settings. Plese refer to the MetroSelect Progrmming Mnul (MLPN 2407) for instructions on chnging the scnner s configurtion. In ddition, plese check tht the scnner nd host system re using the sme communiction protocol. Cution: To mintin complince with pplicble stndrds, ll circuits connected to the scnner must meet the requirements for SELV (Sfety Extr Low Voltge) ccording to EN 60950. To mintin complince with stndrd CSA C22.2 No. 950/UL 1950 nd norm EN 60950, the power source should meet pplicble performnce requirements for limited power source. 4
INSTALLING THE IS6520-47/MS6520-47 TO THE PC 1. Turn off the PC. 2. Connect the 10-pin RJ45 mle connector into the jck on the Cubit IS6520/MS6520. You will her click when the connection is mde. 3. Connect the L-shped plug of the power supply into the power jck on the PowerLink cble. Refer to Mnufcturer s Recommendtion below. 4. Connect the power supply into n AC outlet. Mke sure the AC input requirements of the power supply mtch the AC outlet. 5. Disconnect the keybord from the PC. 6. The PowerLink cble is terminted with 5-pin DIN femle connector on one end, nd 6-pin mini DIN mle on the other. Metrologic will supply n dpter cble with 5-pin DIN mle connector on one end nd 6-pin mini DIN femle connector on the other. According to the termintion required, connect the pproprite end of the dpter cble to the PowerLink cble, leving the necessry termintion exposed for connecting to the keybord nd the keybord port on the PC. Refer to Appendix C pge 31 for pin ssignments. 7. Connect to the PowerLink cble to the keybord nd the keybord port on the PC. 8. Power up the PC. & Mnufcturer s Recommendtion: Metrologic recommends the use of n externl power supply with IS6520-47/MS6520 Keybord Wedge pplictions. Powering the IS6520-47/MS6520 directly from the computer keybord connector could interfere with the opertion of the scnner or the computer. Not ll computers supply the sme current through the keybord port, explining why scnner would work on one computer nd not nother. Cution: To mintin complince with pplicble stndrds, ll circuits connected to the scnner must meet the requirements for SELV (Sfety Extr Low Voltge) ccording to EN 60950. To mintin complince with stndrd CSA C22.2 No. 950/UL 1950 nd norm EN 60950, the power source should meet pplicble performnce requirements for limited power source. 5
DISCONNECTING THE POWERLINK CABLES FROM THE SCANNER Before removing the cble from the scnner, Metrologic recommends tht the power on the host system is off nd the power supply hs been disconnected from the PowerLink cble. & 1. Locte the smll pin-hole on the bck of the scnner. 2. Bend n ordinry pperclip into the shpe shown bove. 3. Insert the pperclip (or other smll metllic pin) into the smll pin-hole. 4. You will here fint click. Pull gently on the strin-relief of the PowerLink cble nd it will slide out of the scnner. 6
SCANNER PARTS A. Speker Serves s n udible indictor. C B. Green & Red LEDs During norml opertion, the green LED is on. This indictes tht the lser is on nd the unit is redy to scn. On successful red of br code, the red LED will turn on. After communiction to the host is complete, the red LED will turn off. The LEDs re lso used s dignostic indictors nd mode indictors. A D B C. Output Window Lser light emits form this perture. D. PowerLink Cble The IS6520/MS6520 scnner hs 10-pin modulr jck. The 10-pin modulr plug on the PowerLink cble connects into the IS6520/MS6520. MOUNTING HOLES Ech IS6520/MS6520 Cubit is equipped with three threded mounting holes locted on the bck of the scnner. The following digrm shows the exct loction of ech mounting hole. The mounting holes re 6 millimeters deep nd re threded for use with 3 millimeter screws. Cution: Using screw tht is longer thn 6 millimeters cn potentilly dmge the scnner. 7
STANDS Fixed Verticl Stnd (MLPN 46-46145) Optionl purchse.. Fixed Verticl Stnd... Qty. 1 b. #7 x 1.00 Wood Screw... Qty. 3 e. d. c. M3 x 0.5 x 6 mm Screw... Qty. 3 c.. b. Tilt Stnd (MLPN 46-46486) Shipped with the MS6520 only. c. Tilt Stnd... Qty. 1 d. #8 x 1.00 Wood Screw... Qty. 3 Fixed Verticl Stnd Instlltion (MLPN 46-46145) Tilt Stnd Instlltion (MLPN 46-46486) Step 1: Drill three #43 pilot holes in the countertop. Step 2: Attch the stnd to the countertop with the three #7 wood screws provided. Step 3: Attch the scnner to the stnd with the three M3 screws provided. Step 1: Drill three #39 pilot holes in the countertop. Step 2: Insert the scnner into the rubber boot (the MS6520 is shipped ssembled). Step 3: Tilt the scnner forwrd in the stnd. Step 4: Attch the stnd to the countertop using the three #8 wood screws provided. Step 5: Tilt the scnner bck into plce. 8
AUDIBLE INDICATORS When the IS6520/MS6520 scnner is in opertion, it provides udible feedbck. These sounds indicte the sttus of the scnner. Eight settings re vilble for the tone of the beep (norml, 6 lternte tones nd no tone). To chnge the tone, refer to the MetroSelect Progrmming Guide MLPN 2407. One Beep When the scnner first receives power, the green LED will turn on, then the red LED will flsh nd the scnner will beep once. (The red LED will remin on for the durtion of the beep.) The scnner is redy to scn. When the scnner successfully reds br code, the red LED will flsh nd the scnner beeps once (if progrmmed to do so). If the scnner does not beep once nd the green light does not flsh, then the br code hs not been successfully red. Rzzberry Tone This tone is filure indictor. Refer to Filure Modes" pge 10. Three Beeps - During Opertion During opertion of the scnner, the red LED will flsh while the scnner simultneously beeps three times (while going into progrmming mode). The red LED will continue to flsh until the unit exits progrm mode. Upon exiting progrm mode, the scnner will beep three times nd the red LED will stop flshing. When configured, 3 beeps cn lso indicte communictions timeout during norml scnning mode. When using one-code-progrmming, the scnner will beep three times (the current selected tone), followed by short puse then by high tone nd low tone. This tells the user tht the single configurtion br code hs successfully configured the scnner. Three Beeps - On Power Up This is filure indictor. Refer to Filure Modes on pge 10. 9
FAILURE MODES Flshing Green nd One Rzzberry Tone This indictes the scnner hs experienced lser subsystem filure. Return the unit for repir t n uthorized service center. Flshing Green nd Red nd Two Rzzberry Tones This indictes the scnner hs experienced motor filure. Return the unit for repir t n uthorized service center. Continuous Rzzberry Tone with Both LEDs Off If, upon power up, the scnner emits continuous rzzberry tone, then the scnner hs n electronic filure. Return the unit for repir t n uthorized service center. Three Beeps - On Power Up If the scnner beeps 3 times on power up then, the nonvoltile memory tht holds the scnner configurtion hs filed. Return the unit for repir t n uthorized service center. 10
VISUAL INDICATORS There is red LED nd green LED on IS6520/MS6520. When the scnner is on, the flshing or sttionry, ctivity of the LEDs indictes the sttus of the current scn nd the scnner. No Red or Green LED The LEDs will not be illuminted if the scnner is not receiving power from the host or trnsformer. Stedy Green When the lser is ctive, the green LED is illuminted. The green LED will remin illuminted until the lser is dectivted. During the power sve mode, the lser will turn on nd turn off. During this period, the green LED remins illuminted. Stedy Green nd Single Red Flsh When the scnner successfully reds br code, the red LED will flsh nd the scnner will beep once. If the red LED does not flsh or the scnner does not beep once, then the br code hs not been successfully red. Stedy Green nd Stedy Red After successful scn, the scnner trnsmits the dt to the host device. Some communiction modes require tht the host inform the scnner when dt is redy to be received. If the host is not redy to ccept the informtion, the scnner's red LED will remin on until the dt cn be trnsmitted. Stedy Green nd Flshing Red This indictes the scnner is in progrm mode. A rzzberry tone indictes tht n invlid br code hs been scnned in this mode. Stedy Red, Green Off This indictes the scnner my be witing for communiction from the host. 11
PROGRAMMING MODES The IS6520/MS6520 Cubit hs 3 modes of progrmming. Br Codes: Cubit cn be configured by scnning the br codes locted in the MetroSelect Configurtion Guide (MLPN 2407). Plese refer to this guide for instructions. This mnul cn be downloded for FREE from Metrologic s website (www.metrologic.com). MetroSet : This user-friendly Windows-bsed configurtion progrm llows you to simply point-nd-click t the desired scnner options. This progrm cn be downloded for FREE from Metrologic website (www.metrologic.com), or set-up disks cn be ordered by clling 1-800-ID-METRO. Seril Progrmming: This mode of progrmming is idel for OEM pplictions. This mode gives the end-user the bility to send series of commnds using the seril port of the host system. The commnds re equivlent to the numericl vlues of the br codes locted in the MetroSelect Configurtion Guide (MLPN 2407). How does Seril Progrmming work? 1. Ech commnd sent to the scnner is the ASCII representtion of ech numerl in the configurtion br code. The entire numeric string is frmed with n ASCII [stx] nd n ASCII [etx]. EXAMPLE #1: Commnd for Disbling Codbr Commnd = [stx]100104[etx] String Sent to Scnner = 02h 31h 30h 30h 31h 30h 34h 03h (All vlues re hexdeciml). 2. If the commnd sent to the scnner is vlid, the scnner will respond with n [ck]. 3. If the commnd sent to the scnner in invlid, the scnner will respond with [nk]. NOTE: If this occurs, the end-user must strt over t the very beginning of the configurtion sequence. Simply re-trnmsitting the invlid commnd will not work, you must strt over. 4. During progrmming, the motor nd lser remin ctive. YOU CANNOT SCAN ANY BAR CODES WHILE IN PROGRAM MODE. 5. There is 20 second window between commnds. If 20 second timeout occurs, the scnner will send [nk] nd you must strt over. 12
PROGRAMMING MODES (CONTINUED) 6. To enter seril progrm mode, send the following commnd [stx]999999[etx]. 7. To exit seril progrm mode, send the following commnd [stx]999999[etx], the scnner will respond with n [ck] nd long beep. 8. This mode uses the current Bud Rte, Prity, Stop Bits nd Dt Bits settings tht re configured in the scnner. The defult settings of the scnner re 9600, Spce, 2, 7 respectively. If commnd is sent to the scnner to chnge ny of these settings, the chnge will NOT tke effect until fter seril progrm mode is exited. EXAMPLE #2: The following exmple will set the scnner to the fctory defult settings, Disble Scnning of Code 128 br codes, chnge the beeper tone, nd dd G s progrmmble prefix. HOST SCANNER FEATURE COMMAND ASCII REPRESENTATION RESPONSE Enter Progrm Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ck] or 06h Lod Defults [stx]999998[etx] 02h 39h 39h 39h 39h 39h 38h 03h [ck] or 06h Disble Code 128 [stx]100113[etx] 02h 31h 30h 30h 31h 31h 33h 03h [ck] or 06h Alternte Tone 1 [stx]318565[etx] 02h 33h 31h 38h 35h 36h 35h 03h [ck] or 06h Prog. Prefix #1 [stx]903500[etx] 02h 39h 30h 33h 35h 30h 30h 03h [ck] or 06h Code Byte 0 [stx]0[etx] 02h 30h 03h [ck] or 06h Code Byte 7 [stx]7[etx] 02h 37h 03h [ck] or 06h Code Byte 1 [stx]1[etx] 02h 31h 03h [ck] or 06h Exit Progrm Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ck] or 06h The scnner will emit long beep! The commnds sent to the scnner do not include the smll superscripted 3 tht you see in front of ech br code string in the MetroSelect mnul. THE 3 SHOULD NOT BE SENT, IT IS A CODE TYPE DESIGNATION ONLY! As you will note for commnds requiring dditionl br codes to be scnned (such s prefixes, suffixes, timeouts, etc.), simply send the code bytes in the sme order tht you would normlly scn the br codes. 13
PROGRAMMING MODES (CONTINUED) EXAMPLE #3: The following exmple shows the events tht occur when n invlid br code is sent. This smple will lod the fctory defult settings nd then set the bud rte to 19200. HOST SCANNER FEATURE COMMAND ASCII REPRESENTATION RESPONSE Enter Progrm Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ck] or 06h Lod Defults [stx]99999:[etx] 02h 39h 39h 39h 39h 39h 3Ah 03h [nk] or 15h Invlid commnd ws sent, you must strt over! Enter Progrm Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ck] or 06h Lod Defults [stx]999998[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ck] or 06h 19200 Bud Rte [stx]415870[etx] 02h 34h 31h 35h 38h 37h 30h 03h [ck] or 06h Exit Progrm Mode [stx]999999[etx] 02h 39h 39h 39h 39h 39h 39h 03h [ck] or 06h The scnner will emit long beep! This exmple illustrtes 2 importnt points. First, if n invlid commnd is sent from the host, the scnner responds with [nk] nd the end-user must strt over from the beginning. Second, if commnd is sent to chnge the Bud Rte, the new bud rte does not tke effect until fter the end-user exits progrm mode. ABREVIATED ASCII TABLE Chrcter Hex Vlue Deciml Vlue [STX] 02h 2 [ETX] 03h 3 [ACK] 06h 6 [NAK] 15h 21 0 30h 48 1 31h 49 2 32h 50 3 33h 51 4 34h 52 5 35h 53 6 36h 54 7 37h 55 8 38h 56 9 39h 57 14
LABELS Ech scnner hs lbel on the bck of the unit. This lbel hs the model number, dte of mnufcture, seril number, CE nd cution informtion. The following is n exmple of this lbel: MAINTENANCE Smudges nd dirt cn interfere with the proper scnning of br code. Therefore, the output window will need occsionl clening. 1. Spry glss clener onto lint free, non-brsive clening cloth. 2. Gently wipe the scnner window. 15
OPTIMAL LOW AND CLOSE DEPTH OF FIELD WIDTH OF SCAN FIELD (mm) 250 123 225 200 105 175 J H G D B 95 82 73 150 125 100 75 50 DISTANCE: SCANNER FACE TO BAR CODE (mm) 49 45 40 25 0 Minimum Br Code Element Width A B C D E F G H J K mm -.15 -.17 - -.25.33.53 - mils - 5.7-6.8 - - 10 13 21 - Note: The sme depth of field is chieved when progrmming Cubit for either Optiml Low Depth of Field or Close Depth of Field. 16
OPTIMAL HIGH AND NORMAL DEPTH OF FIELD WIDTH OF SCAN FIELD (mm) 123 250 225 200 105 175 J H G D B 95 82 73 68 58 150 125 100 75 50 DISTANCE: SCANNER FACE TO BAR CODE (mm) 49 45 25 0 Minimum Br Code Element Width A B C D E F G H J K mm -.15 -.17 - -.25.33.53 - mils - 5.7-6.8 - - 10 13 21 - Note: The sme depth of field is chieved when progrmming Cubit for either Optiml High Depth of Field or Norml Depth of Field. 17
FAR DEPTH OF FIELD WIDTH OF SCAN FIELD (mm) J 123 114 250 225 200 105 175 H G D B 95 91 82 77 73 150 125 100 75 50 DISTANCE: SCANNER FACE TO BAR CODE (mm) 49 45 25 0 Minimum Br Code Element Width A B C D E F G H J K mm -.15 -.17 - -.25.33.53 - mils - 5.7-6.8 - - 10 13 21-18
TROUBLESHOOTING GUIDE The following guide is for reference purposes only. Contct Metrologic representtive t 1-800-ID-METRO or 1-800-436-3876 to preserve the limited wrrnty terms. All Interfces IS6520/MS6520 Series Troubleshooting Guide SYMPTOMS POSSIBLE CAUSE(S) SOLUTION No LEDs, beep or motor spin No power is being supplied to the scnner Check trnsformer, outlet nd power strip. Mke sure the cble is plugged in to the scnner No LEDs, beep No power is being supplied to the scnner front host Some host system s cnnot supply enough current to power Omni-Quest. Use the power supply included with the scnner. 3 beeps on power up Non-voltile RAM filure Contct Metrologic Representtive, if the unit will not hold the progrmmed configurtion Continuous rzz tone on power up RAM or ROM filure Contct Metrologic Representtive, if the unit will not function Rzz tone nd green LED flsh t power up VLD filure Contct Metrologic Representtive Rzz tone nd both LEDs flsh t power up Scnner motor filure Contct Metrologic Representtive Unit scns, Communictes nd beeps twice Sme symbol timeout set too short Adjust sme symbol timeout for longer time 19
TROUBLESHOOTING GUIDE (CONTINUED) All Interfces IS6520/MS6520 Series Troubleshooting Guide (continued) SYMPTOMS POSSIBLE CAUSE(S) SOLUTION The unit powers up, but does not scn nd/or beep Beeper disbled. No tone selected Enble beeper. Select tone The unit powers up, but does not scn nd/or beep Scnning prticulr symbology tht is not enbled UPC/EAN, Code 39, interleved 2 of 5, Code 93, Code 128 nd Codbr re enbled by defult. Verify tht the type of br code being red hs been selected The unit powers up, but does not scn nd/or beep The scnner hs been progrmmed for chrcter length lock, or minimum length nd br code being scnned does not stisfy the progrmmed criteri Verify tht the br code tht is being scnned flls into the criteri. (Typicl of Non- UPC/EAN codes.) (The scnner defults to minimum of 4 chrcter br code) The unit scns br code, but locks up fter the first scn (red LED stys on) The scnner is configured to support some form of host hndshking but is not receiving the signl If the scnner is setup to support ACK/NAK, RTS/CTS, XON/XOFF or D/E, verify tht the host cble nd host re supporting the hndshking properly The unit scns, but the dt trnsmitted to the host is incorrect The scnner's dt formt does not mtch the host system requirements Verify tht the scnner's dt formt mtches tht required by the host. Mke sure tht the scnner is connected to the proper host port 20
TROUBLESHOOTING GUIDE (CONTINUED) All Interfces IS6520/MS6520 Series Troubleshooting Guide (continued) SYMPTOMS POSSIBLE CAUSE(S) SOLUTION Scnner beeps t some br codes nd NOT for others of the sme br code symbology The print qulity of the br code is suspect Check print mode. The type of printer could be the problem. Chnge print settings. For exmple chnge to econo mode or high speed Scnner beeps t some br codes nd NOT for others of the sme br code symbology The spect rtio of the br code is out of tolernce Check print mode. The type of printer could be the problem. Chnge print settings, ie chnge to econo mode or high speed Scnner beeps t some br codes nd NOT for others of the sme br code symbology The br code my hve been printed incorrectly Check if it is check digit, chrcter, or border problem Scnner beeps t some br codes nd NOT for others of the sme br code symbology The scnner is not configured correctly for this type of br code Check if check digits re set properly Scnner beeps t some br codes nd NOT for others of the sme br code symbology The minimum symbol length setting does not work with the br code Check if the correct minimum symbol length is set 21
TROUBLESHOOTING GUIDE (CONTINUED) RS-232 only IS6520/MS6520 Series Troubleshooting Guide (continued) SYMPTOMS POSSIBLE CAUSE(S) SOLUTION Powers up OK nd scns OK but does not communicte properly to the host Com port t the host is not working or configured properly Check to mke sure tht the bud rte, dt bits, stops bits nd prity of the scnner nd the communiction port mtch nd the progrm is looking for "RS- 232" dt Powers up OK nd scns OK but does not communicte properly to the host Cble not connected to the proper com port Check to mke sure tht the bud rte, dt bits, stops bits nd prity of the scnner nd the communiction port mtch nd the progrm is looking for "RS- 232" dt Powers up OK nd scns OK but does not communicte properly to the host Com port not operting properly Check to mke sure tht the bud rte, dt bits, stops bits nd prity of the scnner nd the communiction port mtch nd the progrm is looking for "RS- 232" dt The host is receiving dt but the dt does not look correct The scnner nd host my not be configured for the sme interfce font Check tht the scnner nd the host re configured for the sme interfce font Chrcters re being dropped Interchrcter dely needs to be dded to the trnsmitted output Add some Interchrcter dely to the trnsmitted output by using the MetroSelect Progrmming Guide MLPN 2407 22
APPENDIX A Design Specifictions Opertionl Light Source: VLD 650 ± 10 nm, 0.681 milliwtts (PEAK) Depth of Field: 0 mm to 176 mm (0 to 7 ) for 0.33 mm (13 mil) br code t defult setting (progrmmble) Scn Speed: 1000 scn lines/second Scn Pttern: 5 fields of 4 prllel lines (omnidirectionl) Scn Lines: 20 Min Br Width: 0.145 mm (5.7 mil) Decode cpbility: Autodiscrimintes ll stndrd br codes; for other symbologies cll Metrologic System Interfces: RS-232, Light Pen Emultion, Keybord Wedge, Stnd Alone Keybord Print Contrst: 35% minimum reflectnce difference Roll, Pitch, Yw: 360, 60,60 Indictors: Green = lser on, redy to scn; Red = good red, decoding Beeper Opertion: 7 tones or no beep Mechnicl Length: 102 mm (4.0") Width: 83 mm (3.25") Height (front edge): 70 mm (2.75") Height (bck edge): 55 mm (2.25") Weight: 298 g (10.5 oz) Termintion: 10 Position Modulr RJ45 Mounting Holes: 3 mm threded; mximum depth of 6 mm (0.24 ) 23
APPENDIX A (CONTINUED) Design Specifictions Electricl Power: Input Voltge: Operting Current: DC Trnsformers: EMC: Lser Clss: 1.0 W 5 VDC ± 0.25 V 200 ma typicl @5VDC Clss 2; 5.2 VDC @ 650 ma FCC, ICES-003 & EN 55022 Clss A CDRH Clss II EN 60825-1:1994/A11: 1996 CLASS 1 Environmentl Operting Temperture: Storge Temperture: Humidity: Light Levels: Contminnts: Ventiltion: -20 C to 40 C (-4 F to 104 F) -40 C to 60 C (-40 F to 140 F) 5% to 95% reltive humidity, non-condensing Up to 4840 Lux (450 footcndles) Seled to resist irborne prticulte contminnts None required Specifictions subject to chnge without notice. 24
APPENDIX B Defult Settings Mny functions of the scnner cn be "progrmmed" - tht is, enbled or disbled. The scnner is shipped from the fctory progrmmed to set of defult conditions. The defult prmeter of the scnner hs n sterisk (*) in the chrts on the following pges. If n sterisk is not in the defult column then the defult setting is Off or Disbled. Every communiction does not support every prmeter. If the communiction supports prmeter listed in the chrts on the following pges, check mrk will pper. Prmeter Defult RS-232* Light Pen UPC/EAN * Code 128 * Code 93 * Codbr Interleved 2 of 5 (ITF) * MOD 10 Check on ITF Code 11 Code 39 * Full ASCII Code 39 MOD 43 Check on Code 39 MSI-Plessey MSI-Plessey, 10/10 Check Digit MSI-Plessey, MOD 10 Check Digit * Prf Support ITF Symbol Lengths Vrible Minimum Symbol Length 4 Symbol Length Lock None Brs High s Code 39 * Spces High s Code 39 Brs High s Scnned Spces High s Scnned DTS/SIEMENS 25
APPENDIX B (CONTINUED) Prmeter Defult RS-232* Light Pen DTS/NIXDORF * NCR F NCR S Poll Light Pen Source Beeper Tone Norml Beep/Trnsmit Sequence Before Trnsmit Communiction Timeout None Rzzberry Tone on Timeout Three Beeps on Timeout No Beeps on Timeout * Enter Power Sve Mode 10 mins. Sme Symbol Rescn Timeout: 200 msecs Sme Symbol Rescn Timeout: 500 msecs Progrmmble in 50 msec steps * (MAX 6.35 seconds) Sme Symbol Rescn Timeout: 1250 msecs Sme Symbol Rescn Timeout: 2000 msecs Interchrcter Dely Progrmmble in 1 msec steps(max 255 msecs) 1 msecs 10 msecs in KBW Number of Scn Buffers 1 Trnsmit UPC-A Check Digit * Trnsmit UPC-E Check Digit Expnd UPC-E Convert UPC-A to EAN-13 Trnsmit Led Zero on UPC-E Convert EAN-8 to EAN-13 Trnsmit UPC-A Number System * 26
APPENDIX B (CONTINUED) Prmeter Defult RS-232* Light Pen Trnsmit UPC-A Mnufcturer ID# * Trnsmit UPC-A Item ID# * Trnsmit Codbr Strt/Stop Chrcters CLSI Editing Trnsmit Mod 43 Check Digit on Code 39 Trnsmit Code 39 Stop/Strt Chrcters Trnsmit Mod 10/ITF Trnsmit MSI-Plessey Check Chrcters Prity Spce Bud Rte 9600 8 Dt Bits 7 Dt Bits * Trnsmit Snyo ID Chrcters Nixdorf ID LRC Enbled UPC Prefix UPC Suffix Trnsmit AIM ID Chrcters STX Prefix ETX Suffix Crrige Return * Line Feed * Tb Prefix Tb Suffix DE Disble Commnd FL Lser Enble Commnd DTR Hndshking Support RTS/CTS Hndshking Chrcter RTS/CTS * 27
APPENDIX B (CONTINUED) Messge RTS/CTS Prmeter Defult RS-232* Light Pen XON/XOFF Hndshking ACK/NA K Two Digit Suppliments s code 39 Five Digit Suppliments s code 39 Booklnd s code 39 977 (2 digit) Supplementl Requirement Suppliments re not Required * Two Digit Redundncy * Five Digit Redundncy 100 msec to Find Supplement Progrmmble in 100 msec steps (MAX 800 msec) * Coupon Code 128 s code 39 Progrmmble Code Lengths 7 vl. Progrmmble Prefix Chrcters 10 vil. Suffix Chrcters Prefixes for individul Code Types Editing Inter Scn-Code Dely Progrmmble (100 msec steps) Function/Control Key Support Minimum Element Width Progrmmble in 5.6 µsec steps Depth of Field 800 msec 1 msec Optiml High Depth of Field * Norml Depth of Field Optiml Low Depth of Field Close Depth of Field Fr Depth of Field 28
APPENDIX C Scnner Pinout Connections The IS6520/MS6520 scnner interfces terminte to 10-pin modulr jck. The seril # lbel indictes the interfce enbled when the scnner is shipped from the fctory. 1 10 IS6520-47 / MS6520-47 Keybord Wedge IS6520-41 / MS6520-41 RS-232/LTPN Pin Function Pin Function 1 Ground 1 Ground 2 RS-232 Trnsmit Output 2 RS-232 Trnsmit Output 3 RS-232 Receive Input 3 RS-232 Receive Input 4 PC Dt 4 RTS Output 5 PC Clock 5 CTS Input 6 KB Clock 6 DTR Input/LTPN Source 7 PC +5V 7 Reserved 8 KB Dt 8 LTPN Dt 9 +5VDC 9 +5VDC 10 Shield Ground 10 Shield Ground Cble Connector Configurtions Stndrd PowerLink cble (MLPN 53000 or 54000) 9-pin D-type femle connector to the PC Pin Function 1 Shield Ground 2 RS-232 Trnsmit Output 3 RS-232 Receive Input 4 DTR Input 5 Power/Signl Ground 6 Light Pen Dt 7 CTS Input 8 RTS Output 9 +5VDC* 9-Pin D-Type Connector 9 5 6 1 * If PowerLink power supply is plugged into the PowerLink cble, +5V will NOT be vilble on this pin. This pin is used when the host is supplying +5V to the scnner. 29
APPENDIX C (CONTINUED) Keybord Wedge Powerlink nd Adpter Cble (MLPN 54-54008) The Keybord Wedge PowerLink cble is terminted with 5-pin DIN femle connector on one end, nd 6-pin mini DIN mle on the other. Keybord Wedge PowerLink Cble 4 2 5 1 3 5-Pin DIN, Femle 2 1 4 3 6 5 6-Pin DIN, Mle Metrologic will supply n dpter cble with 5-pin DIN mle connector on one end nd 6-pin mini DIN femle connector on the other. 2 5 4 3 1 5-Pin Din, Mle Adpter Cble 1 2 3 4 5 6 6-pin Mini Din, Femle According to the termintion required, connect the pproprite end of the dpter cble to the PowerLink cble, leving the necessry termintion exposed for connecting to the keybord nd the keybord port on the PC. The pin ssignments re s follows: PowerLink Cble Adpter Cble 5-pin Femle DIN 5-pin Mle DIN Pin Function Pin Function 1 Keybord Clock 1 PC Clock 2 Keybord Dt 2 PC Dt 3 No Connect 3 No Connect 4 Power Ground 4 Power Ground 5 +5 Volts DC 5 +5 Volts DC 6-pin Mle Mini-DIN 6-pin Femle Mini-DIN Pin Function Pin Function 1 PC Dt 1 Keybord Dt 2 No Connect 2 No Connect 3 Power Ground 3 Power Ground 4 +5 Volts DC 4 +5 Volts DC 5 PC Clock 5 Keybord Clock 6 No Connect 6 No Connect 30
APPENDIX D Wrrnty nd Disclimer Limited Wrrnty The IS6520/MS6520 Cubit scnners re mnufctured by Metrologic t its Blckwood, New Jersey, U.S.A. fcility. The IS6520/MS6520 Cubit scnners hve two (2) yer limited wrrnty from the dte of mnufcture. Metrologic wrrnts nd represents tht ll IS6520/MS6520 Cubit scnners re free of ll defects in mteril, workmnship nd design, nd hve been produced nd lbeled in complince with ll pplicble U.S. Federl, stte nd locl lws, regultions nd ordinnces pertining to their production nd lbeling. This wrrnty is limited to repir, replcement of Product or refund of Product price t the sole discretion of Metrologic. Fulty equipment must be returned to the Metrologic fcility in Blckwood, New Jersey, U.S.A. or Puchheim, Germny. To do this, contct Metrologic s Customer Service/Repir Deprtment to obtin Returned Mteril Authoriztion (RMA) number. In the event tht it is determined the equipment filure is covered under this wrrnty, Metrologic shll, t its sole option, repir the Product or replce the Product with functionlly equivlent unit nd return such repired or replced Product without chrge for service or return freight, whether distributor, deler/reseller, or retil consumer, or refund n mount equl to the originl purchse price. This limited wrrnty does not extend to ny Product which, in the sole judgement of Metrologic, hs been subjected to buse, misuse, neglect, improper instlltion, or ccident, nor ny dmge due to use or misuse produced from integrtion of the Product into ny mechnicl, electricl or computer system. The wrrnty is void if the cse of Product is opened by nyone other thn Metrologic s repir deprtment or uthorized repir centers. THIS LIMITED WARRANTY, EXCEPT AS TO TITLE, IS IN LIEU OF ALL OTHER WARRANTIES OR GUARANTEES, EITHER EXPRESS OR IMPLIED, AND SPECIFICALLY EXCLUDES, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE UNDER THE UNIFORM COMMERCIAL CODE, OR ARISING OUT OF CUSTOM OR CONDUCT. THE RIGHTS AND REMEDIES PROVIDED HEREIN ARE EXCLUSIVE AND IN LIEU OF ANY OTHER RIGHTS OR REMEDIES. IN NO EVENT SHALL METROLOGIC BE LIABLE FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES TO PERSON OR PROPERTY, OR EFFECT ON BUSINESS OR PROPERTY, OR OTHER DAMAGES OR EXPENSES DUE DIRECTLY OR INDIRECTLY TO THE PRODUCT, EXCEPT AS STATED IN THIS WARRANTY. IN NO EVENT SHALL ANY LIABILITY OF METROLOGIC EXCEED THE ACTUAL AMOUNT PAID TO METROLOGIC FOR THE PRODUCT. METROLOGIC RESERVES THE RIGHT TO MAKE ANY CHANGES TO THE PRODUCT DESCRIBED HEREIN. Metrologic Instruments, Inc. Metrologic Instruments GmbH 90 Coles Rod Dornierstrsse 2 Blckwood, NJ 08012-4683 82178 Puchheim b Customer Service Deprtment: Munich, Germny 1-800-ID-METRO (1-800-436-3876) TEL: 49-89-89019-0 TEL: 856-228-8100 FAX: 49-89-89019-200 FAX: 856-228-6673 31
APPENDIX E Notices Notice This equipment hs been tested nd found to comply with limits for Clss A digitl device, pursunt to Prt 15 of the FCC Rules. These limits re designed to provide resonble protection ginst hrmful interference when the equipment is operted in commercil environment. This equipment genertes, uses nd cn rdite rdio frequency energy nd, if not instlled nd used in ccordnce with the instruction mnul, my cuse hrmful interference to rdio communictions. Opertion of this equipment in residentil re is likely to cuse hrmful interference, in which cse the user will be required to correct the interference t his own expense. Any unuthorized chnges or modifictions to this equipment could void the users uthority to operte this device. This device complies with Prt 15 of the FCC Rules. Opertion is subject to the following two conditions: (1) This device my not cuse hrmful interference, nd (2) this device must ccept ny interference received, including interference tht my cuse undesired opertion. Notice This Clss A digitl pprtus complies with Cndin ICES-003. Remrque Cet ppreil numérique de l clsse A est conforme à l norme NMB-003 du Cnd. Cution Use of controls or djustments or performnce of procedures other thn those specified herein my result in hzrdous lser light exposure. Under no circumstnces should the customer ttempt to service the lser scnner. Never ttempt to look t the lser bem, even if the scnner ppers to be nonfunctionl. Never open the scnner in n ttempt to look into the device. Doing so could result in hzrdous lser light exposure. The use of opticl instruments with the lser equipment will increse eye hzrd. Atención L modificción de los procedimientos, o l utilizción de controles o justes distintos de los especificdos quí, pueden provocr un luz de láser peligros. Bjo ningun circunstnci el usurio deberá relizr el mntenimiento del láser del escáner. Ni intentr mirr l hz del láser incluso cundo este no esté opertivo. Tmpoco deberá brir el escáner pr exminr el prto. El hcerlo puede conllevr un exposición peligros l luz de láser. El uso de instrumentos ópticos con el equipo láser puede incrementr el riesgo pr l vist. Attention L'emploi de commndes, réglges ou procédés utres que ceux décrits ici peut entrîner de grves irrditions. Le client ne doit en ucun cs essyer d'entretenir lui-même le scnner ou le lser. Ne regrdez jmis directement le ryon lser, même si vous croyez que le scnner est inctif. N'ouvrez jmis le scnner pour regrder dns l'ppreil. Ce fisnt, vous vous exposez à une ryonnement lser qú êst hzrdous. L'emploi d'ppreils optiques vec cet équipement lser ugmente le risque d'endommgement de l vision. Achtung Die Verwendung nderer ls der hier beschriebenen Steuerungen, Einstellungen oder Verfhren knn eine gefährliche Lserstrhlung hervorrufen. Der Kunde sollte unter keinen Umständen versuchen, den Lser-Scnner selbst zu wrten. Sehen Sie niemls in den Lserstrhl, selbst wenn Sie gluben, dß der Scnner nicht ktiv ist. Öffnen Sie niemls den Scnner, um in ds Gerät hineinzusehen. Wenn Sie dies tun, können Sie sich einer gefährlichen Lserstrhlung ussetzen. Der Einstz optischer Geräte mit dieser Lserusrüstung erhöht ds Risiko einer Sehschädigung. Attenzione L utilizzo di sistemi di controllo, di regolzioni o di procedimenti diversi d quelli descritti nel presente Mnule può provocre delle esposizioni rggi lser rischiose. Il cliente non deve ssolutmente tentre di riprre egli stesso lo scnner lser. Non gurdte mi il rggio lser, nche se credete che lo scnner non si ttivo. Non prite mi lo scnner per gurdre dentro l pprecchio. Fcendolo potete esporvi d un esposizione lser rischios. L uso di pprecchi ottici, equipggiti con rggi lser, ument il rischio di dnni ll vist. 32
APPENDIX E (CONTINUED) Europen Stndrd Wrning This is clss A product. In domestic environment this product my cuse rdio interference in which cse the user my be required to tke dequte mesures. Funkstöreigenschften nch EN 55022:1998 Wrnung! Dies ist eine Einrichtung der Klsse A. Diese Einrichtung knn im Wohnbereich Funkstörungen verurschen; in diesem fll knn vom Betrieber verlngt werden, ngemessene Mßnhmen durchführen. Stndrd Europeo Attenzione Questo e un prodotto di clsse A. Se usto in vicinnz di residenze privte potrebbe cusre interferenze rdio che potrebbero richiedere ll utilizztore opportune misure. Attention Ce produit est de clsse A. Dns un environnement domestique, ce produit peut être l cuse d interférences rdio. Dns ce cs l utiliseteur peut être mené à predre les mesures déqutes. 33
APPENDIX F Ptents Ptent Informtion This METROLOGIC product my be covered by one or more of the following U.S. Ptents: U.S. Ptent No.; 4,960,985; 5,081,342; 5,216,232; 5,260,553; 5,340,971; 5,525,789; 5,557,093; 5,627,359; 5,637,852; 5,777,315; 5,789,731; 6,029,894; 6,098,885; 6,209,789; 4,360,798; 4,369,361; 4,387,297; 4,460,120; 4,496,831; 4,593,186; 4,607,156; 4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,923,281; 4,933,538; 4,992,717; 5,081,342; 5,015,833; 5,017,765; 5,059,779; 5,117,098; 5,124,539; 5,130,520; 5,132,525; 5,140,144; 5,149,950; 5,180,904; 5,200,599; 5,229,591; 5,247,162; 5,250,790; 5,250,791; 5,250,792; 5,262,628; 5,280,162; 5,280,164; 5,304,788; 5,321,246; 5,324,924; 5,396,053; 5,396,055; 5,408,081; 5,410,139; 5,436,440; 5,449,891; 5,468,949; 5,479,000; 5,532,469; 5,545,889; No license right or sublicense is grnted, either expressly or by impliction, estoppel, or otherwise, under ny METROLOGIC or third prty intellectul property rights (whether or not such third prty rights re licensed to METROLOGIC), including ny third prty ptent listed bove, except for n implied license only for the norml intended use of the specific equipment, circuits, nd devices represented by or contined in the METROLOGIC products tht re physiclly trnsferred to the user, nd only to the extent of METROLOGIC S license rights nd subject to ny conditions, covennts nd restrictions therein. Other world wide ptents pending. 34
INDEX A AC input/outlet...2, 3, 4, 5, 29 Accessories...2 Approvls...15, 32, 33 Assignments Pin...29 Audible...9 Autodiscrimintes...23 B Br code1, 3, 9, 11, 12, 15, 16, 17, 18, 20, 21, 25 Br width...23 Beep... 3, 9, 10, 11, 19, 20, 21, 26 C Cble...2, 3, 22, 30 communiction...29, 30 detchble...1, 6, 29, 30 pin ssignments...29, 30 powerlink...4, 5, 6, 30 Cution... 4, 5, 7, 15, 32, 33 CDRH...24 Ce...32 Communiction...4, 11, 22, 25 Complince...32, 33 Current...9, 19, 24 Customer service...2, 31 D DC trnsformer...24 Decode cpbility...23 Defult settings...25, 26, 27, 28 Depth of field... 16, 17, 18, 23, 28 Design specifictions...23 Disclimer...31 E Electricl...24 F Filure indictor(s)... 9 Filure modes... 9, 10 G Green LED... 11, 19 H Host... 2, 4, 6, 11, 20, 22, 29 I Indictors... 9, 10, 11, 23 udible... 9 LED... 7, 9, 10, 11, 19, 20 Visul... 11 Input voltge... 24 Instlltion... 4, 7, 8 Interfces... 1, 19, 20, 21, 23 K Keybord wedge... 1, 2, 29, 30 L Lbels... 15 Light levels... 24 Light pen... 25, 26, 27, 28 Light Pen... 1, 23, 25, 26, 27, 28 Light source... 23 List... 2 M Mintennce... 15 N Notices... 32, 33 35
INDEX O Operting current...24 Operting temperture...24 Opertion...9, 23, 32 Opertionl...23 Output window...7 P Prts...2, 7 PC...4 Port...5, 22 Power supply...1, 2, 5, 29 Powerlink...2, 3, 4, 6 Progrmming guide...3, 9, 12 Progrmming modes...12, 13, 14 Q Quick strt...3 R Rzzberry tone...9, 10, 11, 26 Red LED...9, 11, 20 Repir...10 RMA...31 RS-232... 22, 23, 25, 26, 27, 28 S Scn lines... 23 Scn pttern... 23 Scn speed... 23 Service... 2, 10, 31 Specifictions... 23, 24 System interfces... 23 T Termintion... 5, 23 Tones... 9, 10, 23 Trnsformers... 24 Troubleshooting... 19, 20, 21, 22 V Ventiltion... 24 Visul... 11 Voltge... 24 W Wrrnty... 19, 31 Weight... 23 Window... 7, 15 36
July 2003 Printed in the USA 00-02421A