LED Area Luminaire Area and Roadway Lighting
An economy LED luminaire that delivers big on style and performance The specifier searching for an economy LED outdoor area luminaire that also delivers big on style and performance is often left at an impasse. Finding a luminaire with any two of the three qualities is simple enough... but finding all three together seemed hopeless. Until now. Introducing the Emco LED Outdoor Area Luminaire Combining commanding aesthetics, advanced LED performance and attractive pricing, the Emco LED Area luminaire is perhaps the most versatile and cost effective luminaire on the market. 16" LED Area luminaire wall mount shown with black paint (LP) 2 21" LED Area luminaire shown with natural aluminum paint (NP)
16" LED Area luminaire mast arm mount shown with natural aluminum paint (NP) With an extremely low profile, the LED Area luminaire is an obvious choice for street and roadway applications. The mast arm mount is designed for a smooth transition from the luminaire to the mast arm, bringing style and grace to a usually utilitarian application. In addition to the standard arm mount, the Emco LED Area luminaire is also available in wall mount configurations. The Emco LED Area luminaire redefines what designers and specifiers can expect from an economy LED luminaire. Striking from every vantage, its angular profile is distinctly modern, though subdued enough to blend into any architectural environment. At night is when LED Area luminaire truly shines, with an advanced low-wattage, high-power LED array available in four distribution patterns. Available in two sizes and four LED wattages, the LED Area luminaire is ideal for a wide range of applications. Combined with a rugged die cast aluminum housing that will stand up to the harshest conditions, it s clear that the Emco LED Area luminaire sets a new standard for area illumination for LEDs. 16" LED Area luminaire shown with bronze paint (RP) 3
It's not enough to simply place high power LEDs into existing luminaires. Thermal management is crucial. If the generated heat is not adequately removed, the LEDs will run at higher temperatures, not only lowering their efficiency, but also shortening their life and threatening their reliability. The LED Area luminaire is specifically designed to handsomely address this issue. The streamlined die cast aluminum housing is defined by deep integral airways that direct substantial airflow over the luminaire and dissipate heat. At just over three inches deep, these air channels cool the system components while allowing for a remarkably sleek profile just 4.5" maximum height. From front-to-back, inside and out, every aspect speaks to the thoughtful, economical and stylish approach to both initial and long-term performance. Engineered for Easy Assembly Extruded arm assemblies are designed with integral guide channels and a double-nut-through-bolt that effectively makes it impossible to misalign the luminaire and pole. Designed for Easy Maintenance The internal components are totally enclosed within the rain-tight, dusttight and corrosion-resistant die cast aluminum housing. Access to the compartment is simple, requiring the removal of two screws allowing the cover plate to hinge open. Integral ird Deterrent Deliberately spaced and specifically sized cables deter bird nesting and perching, helping to keep the luminaire clean and running at maximum efficeincy. 21" LED Area luminaire shown with RAL5024 paint.
Designed to perform, engineered to last The heart of the luminaire is its high-performance optical system, available in four distinct distribution patterns. The system utilizes an integral array of long-lasting, energy-efficient LEDs oriented to achieve an IES Type II, III, IV, or V distribution with full cutoff performance, consistent uniformity and minimal light trespass. Aided by an integral thermal control system, the LED arrays carry L70 ratings of up to 100,000 hours, minimizing the hassle and expense of maintenance. The result is minimal required maintenance and reduced energy costs, saving both time and money. Field Rotatable Optics The LED arrays are fully rotatable in 90 increments on 21" luminaires, permitting aiming of the distributions in any of four directions. As a result, the luminaires and poles maintain a consistent visual alignment while light is placed where it is needed most. Type 2 These optics create an asymmetric distribution pattern with wide lateral throw. This distribution works well in walkway and roadway applications where more light is required street side than house side. Type 3 Type 3 optics produce an asymmetrical pattern that directs the majority of the light forward and equally on both sides of the luminaire. In a back-to-back configuration, it creates a rectangular pattern which can extend pole spacings. Type 4 The Type 4 pattern is suitable for applications where light is primarily required forward with minimal backlight. Typical installations include perimeter poles. Type 5 Type 5 optics produce a symmetrical square distribution pattern that distributes light equally on all sides of the luminaire. The optical system is universal for most area lighting applications. 5
LED Area Luminaire Specifications GENERAL DESCRIPTION: Emco LED Area luminaires combine a low profile style with advanced LED performance and thermal management technology to deliver outdoor area lighting that is as energy efficient and aesthetically pleasing as it is remarkably economical. HOUSING: The housing is one-piece, die cast aluminum and mounts to a pole, utilizing an extruded arm. Additionally, LED Area luminaires mount easily to a wall or to a mast arm while providing smooth visual transitions. LED THERMAL MANAGEMENT: The LED Area luminaire design provides die cast aluminum integral thermal radiation fins to provide the excellent thermal management so critical to long LED system life. LED PERFORMANCE: PREDICTED LUMEN DEPRECIATION DATA Ambient Temperature C 25 C 40 C LED Wattages / Driver ma L70 Hours 70LA, 150LA / 400 ma 100,000 110LA, 210LA / 600 ma 75,000 70LA, 150LA / 400 ma 65,000 110LA, 210LA / 600 ma 50,000 Predicted performance derived from LED manufacturer s data and engineering design estimates, based on IESNA LM-80 methodology. Actual experience may vary due to field application conditions. L70 is the predicted time when LED performance depreciates to 70% of initial lumen output. OPTICAL SYSTEMS: Lensed LED arrays are set to achieve IES Type II, Type III, Type IV and Type V distributions. Individual LED arrays are replaceable. ELA21 optics are rotatable. ELECTRICAL: Luminaires are equipped with an LED driver that accepts 120V through 277V, 50hz to 60hz, input. Driver output is based on the LED wattage selected. Component-to-component wiring within the luminaire will carry no more than 80% of rated current and is listed by UL for use at 600 VAC at 302 F / 150 C or higher. Plug disconnects are listed by UL for use at 600 VAC, 15A or higher. LED board, LED driver and LED array are RoHS compliant. FINISH: Each standard color luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) textured polyester powdercoat finish. Standard colors include bronze (RP), black (LP), white (WP), and natural aluminum (NP). Consult factory for specs on optional or custom colors. LAELS: All luminaires bear UL or CUL (where applicable) Wet Location labels. WARRANTY: Emco luminaires feature a 1 year limited warranty. Emco LED luminaires with LED arrays feature a 5 year limited warranty covering the LED arrays. See Warranty Information on sitelighting.com for complete details and exclusions. DIMENSIONS Arm Mount - Direct to Pole A G F C Dimensions ELA16 ELA21 A Side Arm 4.5" / 11.43 cm 4.5" / 11.43 cm A Wall racket 7.25" / 18.42 cm 7.25" / 18.42 cm Side Arm 6.28" / 15.95 cm 9.28" / 23.57 cm D E Mast Arm Wall racket 7.80" / 19.81 cm 7.80" / 19.81 cm 2.59" / 18.42 cm 2.59" / 18.42 cm C 16.53" / 41.99 cm 21.52" / 54.66 cm D 2" / 5.08 cm 2" / 5.08 cm E 15.2" / 38.61 cm 15.7" / 39.88 cm F 4.6" / 11.68 cm 4.6" / 11.68 cm G 1.53" / 3.89 cm 1.53" / 3.89 cm Prior to ordering, consult Submittal Data Sheet on sitelighting.com for the most current information, notes and exclusions. 6 Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program.
PREFIX MOUNTING OPTICAL SYSTEM LED WATTAGE LED SELECTION VOLTAGE Ordering PAINTED FINISH OPTIONS Example ELA16 1 5 110LA NW UNIV NP F ELA16 ELA21 1 Single 2 Twin @180 2@90 Twin @90 3 Triple @90 3@120 Triple @120 4 4 Way W Wall Mount Recessed J-ox WS Wall Mount Surface Conduit MA Mast Arm Mount Requires a 2 3/8" Mast Arm 2 IES Type II 3 IES Type III 4 IES Type IV 5 IES Type V ELA16 70LA 110LA ELA21 150LA 210LA CW Cool White 6,000 K, 75 CRI NW Neutral White 4,000 K, 75 CRI UNIV 120V through 277V 50hz or 60hz RP ronze LP lack WP White NP Natural Aluminum OC Optional Color Specify Optional Color or RAL ex: OC-LGP or OC-RAL7024 SC Special Color Specify. Must supply color chip. F 1 LF PC 1 PCR HS PTF2 PTF3 PTF4 DL SPR DCC OPTIONS F 1 LF PC 1 PCR HS PTF2 PTF3 PTF4 DL SPR DCC NOTES: Fusing In Head In-Line/In-Pole Fusing Photocontrol and Receptacle Photocontrol Receptacle only External House Side Shield Pole Top Fitter - 2 3/8" - 2 7/8" Dia. Tenon Pole Top Fitter - 3" - 3 1/2" Dia. Tenon Pole Top Fitter - 3 1/2" - 4" Dia. Tenon Diffusing Lens Reduces performance significantly. Surge Protection for 120V through 277V Input Not available with Fusing (F) option. Dual Circuit - LED Array Control ELA21 only. Provides dual level control capability. Each LED array can be switched or circuited separately. 1. Provide specific input voltage. Photocontrol Placement Cast seat allows for secure placement of the photocontrol receptacle at the top of the luminaire. (W/WS) Wall Mount Plate olt Pattern (MA) Mast Arm Mount 2.75" 6.985 cm 3.75" 9.525 cm 1.75" 4.445 cm Dia. Wall Mounting Plate may be mounted over (not to) a recessed j-box (by others) and in all cases must be properly supported to structure as indicated. Surface conduit mount requires conduit entry from below. See installation instruction sheets on sitelighting.com for more details. A (W/WS) Wall Mount Holes for 3/8" (.9525 cm) Studs or olts (by others) NOTE: Wall mounting bracket is secured to wall with 3/8" (.9525 cm) studs or bolts (by others.) Structural members must be present in wall to accept bolts. ELA16 ELA21 Effective Projected Area (EPA) Single Twin 3/4 Approximate Weight - Single Luminaire.87 ft 2 1.74 ft 2 2.49 ft 2 21 lbs.081 m 2.162 m 2.232 m 2 9.53 kg.95 ft 2 1.9 ft 2 2.79 ft 2 31 lbs.089 m 2.177 m 2.26 m 2 14.07 kg Prior to ordering, consult Submittal Data Sheet on sitelighting.com for the most current information, notes and exclusions. Philips Gardco reserves the right to change materials or modify the design of its product without notification as part of the company s continuing product improvement program. 7
1611 Clovis arker Road San Marcos, TX 78666 512/753-1000 800/227-0758 Fax: 512/753-7855 sitelighting.com Emco Lighting by Philips Gardco Warranty Emco luminaires feature a 1 year limited warranty. Emco LED luminaires with LED arrays feature a 5 year limited warranty covering the LED arrays. See Warranty Information on sitelighting.com for complete details and exclusions. 2010 Koninklijke Philips Electronics N.V. All Rights Reserved. Document order number: E100-002/1210