AX-59/9 Natura Sound Stereo Integrated Ampifier 1W + 1W (Ω) RMS Output Power,.15% THD,, Hz 5W + 5W (Ω) RMS Output Power,.19% THD,, Hz <AX-9> High Dynamic Power, Low Impedance Drive Capabiity Continuousy Variabe Loudness Contro CD DIRECT AMP Switch to Reproduce the Purest CD Sound PURE DIRECT Switch to Reproduce the Purest Source Sound SUBSONIC FILTER Switch to Cut Out Undesirabe Utra-Low-Frequency Signas <For AX-59 ony> PRE OUT/MAIN IN Terminas Usefu for Connecting An Equaizer, Sound Processor, etc. <For AX-59 ony> Remote Contro Capabiity Thank you for seecting this YAMAHA stereo integrated ampifier. CAUTION RISK OF ELECTRIC SHOCK CONTENTS OWNER S MANUAL Safety Instructions... Suppied Accessories... Connections... Operations... 7 Remote Contro Transmitter... 11 Notes about the Remote Contro Transmitter... 1 Troubeshooting... 1 Specifications... 1 IMPORTANT! Pease record the seria number of this unit in the space beow. Seria No.: The seria number is ocated on the rear of the unit. Retain this Owner s Manua in a safe pace for future reference. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Expanation of Graphica Symbos The ightning fash with arrowhead symbo, within an equiatera triange, is intended to aert you to the presence of uninsuated dangerous votage within the product s encosure that may be of sufficient magnitude to constitute a risk of eectric shock to persons. The excamation point within an equiatera triange is intended to aert you to the presence of important operating and maintenance (servicing) instructions in the iterature accompanying the appiance.
SAFETY INSTRUCTIONS 1 Read Instructions A the safety and operating instructions shoud be read before the unit is operated. Retain Instructions The safety and operating instructions shoud be retained for future reference. Heed Warnings A warnings on the unit and in the operating instructions shoud be adhered to. Foow Instructions A operating and other instructions shoud be foowed. 5 Water and Moisture The unit shoud not be used near water for exampe, near a bathtub, washbow, kitchen sink, aundry tub, in a wet basement, or near a swimming poo, etc. Carts and Stands The unit shoud be used ony with a cart or stand that is recommended by the manufacturer. A A unit and cart combination shoud be moved with care. Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn. 7 Wa or Ceiing Mounting The unit shoud be mounted to a wa or ceiing ony as recommended by the manufacturer. Ventiation The unit shoud be situated so that its ocation or position does not interfere with its proper ventiation. For exampe, the unit shoud not be situated on a bed, sofa, rug, or simiar surface, that may bock the ventiation openings; or paced in a buit-in instaation, such as a bookcase or cabinet that may impede the fow of air through the ventiation openings. 9 Heat The unit shoud be situated away from heat sources such as radiators, stoves, or other appiances that produce heat. 1 Power Sources The unit shoud be connected to a power suppy ony of the type described in the operating instructions or as marked on the unit. 11 Power-Cord Protection Power-suppy cords shoud be routed so that they are not ikey to be waked on or pinched by items paced upon or against them, paying particuar attention to cords at pugs, convenience receptaces, and the point where they exit from the unit. 1 Ceaning The unit shoud be ceaned ony as recommended by the manufacturer. 1 Nonuse Periods The power cord of the unit shoud be unpugged from the outet when eft unused for a ong period of time. 1 Object and Liquid Entry Care shoud be taken so that objects do not fa into and iquids are not spied into the inside of the unit. 15 Damage Requiring Service The unit shoud be serviced by quaified service personne when: A. The power-suppy cord or the pug has been damaged; or B. Objects have faen, or iquid has been spied into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normay or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 1 Servicing The user shoud not attempt to service the unit beyond those means described in the operating instructions. A other servicing shoud be referred to quaified service personne. 17 Power Lines An outdoor antenna shoud be ocated away from power ines. 1 Grounding or Poarization Precautions shoud be taken so that the grounding or poarization is not defeated. Caution: Read this before operating your unit 1 To assure the finest performance, pease read this manua carefuy. Keep it in a safe pace for future reference. Insta this unit in a coo, dry, cean pace away from windows, heat sources, sources of excessive vibration, dust, moisture and cod. Avoid sources of humming (transformers, motors). To prevent fire or eectrica shock, do not expose the unit to rain and water. Do not operate the unit upside-down. It may overheat, possiby causing damage. Never open the cabinet. If something drops into the set, contact your deaer. 5 Do not use force on switches, contros or connection wires. When moving the unit, first disconnect the power pug and the wires connected to other equipment. Never pu the wires themseves. Do not attempt to cean the unit with chemica sovents; this might damage the finish. Use a cean, dry coth. 7 Aways set the VOLUME contro to before starting the audio source pay: increase the voume graduay to an appropriate eve after the pay back has been started. To prevent ightning damage, pu out the power cord and remove the antenna cabe during an eectrica storm. 9 When not panning to use this unit for ong periods of time (ie., vacation, etc.), disconnect the AC power pug from the wa outet. 1 Be sure to read the TROUBLESHOOTING section regarding common operating errors before concuding that the unit is fauty. 11 AC outets Do not connect audio equipment to the AC outets on the rear pane if that equipment requires more power than the outets are rated to provide.
FCC INFORMATION 1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when instaed as indicated in the instructions contained in this manua, meets FCC requirements. Modifications not expressy approved by Yamaha may void your authority, granted by the FCC, to use the product.. IMPORTANT : When connecting this product to accessories and/or another product use ony high quaity shieded cabes. Cabe/s suppied with this product MUST be used. Foow a instaation instructions. Faiure to foow instructions coud void your FCC authorization to use this product in the USA.. NOTE : This product has been tested and found to compy with the requirements isted in FCC Reguations, Part 15 for Cass B digita devices. Compiance with these requirements provides a reasonabe eve of assurance that your use of this product in a residentia environment wi not resut in harmfu interference with other eectronic devices. This equipment generates/uses radio frequencies and, if not instaed and used according to the instructions found in the users manua, may cause interference harmfu to the operation of other eectronic devices. Compiance with FCC reguations does not guarantee that interference wi not occur in a instaations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, pease try to eiminate the probem by using one of the foowing measures: Reocate either this product or the device that is being affected by the interference. Utiize power outets that are on different branch (circuit breaker or fuse) circuits or insta AC ine fiter/s. In the case of radio or TV interference, reocate/reorient the antenna. If the antenna ead-in is ohm ribbon ead, change the ead-in to coaxia type cabe. If these corrective measures do not produce satisfactory resuts, pease contact the oca retaier authorized to distribute this type of product. If you can not ocate the appropriate retaier, pease contact Yamaha Eectronics Corp., U.S.A. Orangethorpe Ave, Buena Park, CA 9. The above statements appy ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. We Want You Listening For A Lifetime YAMAHA and the Eectronic Industries Association s Consumer Eectronics Group want you to get the most out of your equipment by paying it at a safe eve. One that ets the sound come through oud and cear without annoying baring or distortion and, most importanty, without affecting your sensitive hearing. Since hearing damage from oud sounds is often undetectabe unti it is too ate, YAMAHA and the Eectronic Industries Association s Consumer Eectronics Group recommend you to avoid proonged exposure from excessive voume eves. SUPPLIED ACCESSORIES After unpacking, check that the foowing parts are contained. Remote Contro Transmitter Batteries (size AA, R, UM-)
CONNECTIONS Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made. When making connections between this unit and other components, be sure a connections are made correcty, that is to say L (eft) to L, R (right) to R, + to + and to. Aso, refer to the owner s manua for each component to be connected to this unit. AX-59 Compact disc payer Turntabe Tape deck Speakers A OUTPUT OUTPUT GND LINE OUT LINE IN Right Left GND AC OUTLETS MM/MC SWITCHED CD REMOTE CONTROL SPEAKERS V Hz W MAX. TOTAL A PRE OUT MAIN IN TAPE PB REC OUT TAPE PB REC OUT B TUNER TAPE 1 TAPE COUPLER A OR B:ΩMIN./SPEAKER A B:ΩMIN./SPEAKER To AC outet OUTPUT LINE OUT LINE IN AUDIO OUT Tuner Tape deck 1 Video cassette payer, LD payer, etc. Right Speakers B Left : Refer to ABOUT THE OTHER REAR PANEL PARTS on page. (MM/MC) switch AX-59 ony Seect either MM or MC position depending on your cartridge, Moving Magnet or Moving Coi type. However, if you use a high output MC cartridge, seect MM position. To seect the MC position, press this switch so that it is hed inward. To seect the MM position, press this switch so that it is reeased outward. MM/MC
AX-9 Compact disc payer Tuner Tape deck 1 Speakers A OUTPUT OUTPUT LINE OUT LINE IN Right Left (U.S.A. mode) GND CD TUNER AC OUTLETS TAPE PB TAPE 1 SPEAKERS SWITCHED V Hz W MAX. TOTAL MAINS REC OUT TAPE PB A TAPE REC OUT B REMOTE CONTROL A OR B:ΩMIN./SPEAKER A B:ΩMIN./SPEAKER GND OUTPUT AUDIO OUT LINE IN LINE OUT To AC outet Turntabe Video cassette payer, LD payer, etc. Tape deck Right Speakers B Left : Refer to ABOUT THE OTHER REAR PANEL PARTS on page. AC OUTLETS (SWITCHED) (U.S.A., Canada, Europe and Genera modes)... SWITCHED OUTLETS (U.K. and Austraia modes)...1 SWITCHED OUTLET Use these to connect the power cords from your components to this unit. The power to the SWITCHED outets is controed by this unit s POWER switch or the provided remote contro transmitter s POWER key. These outets wi suppy power to any component whenever this unit is turned on. The maximum power (tota power consumption of components) that can be connected to the SWITCHED AC OUTLETS is 1 watts. 5
CONNECTING SPEAKERS Connect the SPEAKERS terminas to your speakers with wire of the proper gauge, cut as short as possibe. If the connections are fauty, no sound wi be heard from the speakers. Make sure that the poarity of the speaker wires is correct, that is, + and markings are observed. If these wires are reversed, the sound wi be unnatura and wi ack bass. Do not et the bare speaker wires touch each other and do not et them touch the meta parts of this unit as this coud damage this unit and/or speakers. One or two speaker systems can be connected to this unit. If you connect ony one speaker system, connect it to either the SPEAKERS A or B terminas. Use speakers with the specified impedance shown on the rear of this unit. <U.S.A., Canada and Genera modes ony> Banana Pug connections are aso possibe. Simpy insert the Banana Pug connector into the corresponding termina. How to Connect: Red: positive (+) Back: negative ( ) 1 ➀ Unscrew the knob. ➁ Insert the bare wire. [Remove approx. 5mm (1/ ) insuation from the speaker wires.] ➂ Tighten the knob and secure the wire. ABOUT THE OTHER REAR PANEL PARTS REMOTE CONTROL () connector If you have a YAMAHA turntabe with a termina for remote contro, connect it to this connector by using the cabe provided with the turntabe. This connection aows you to contro the turntabe from the provided remote contro transmitter. GND termina (For turntabe use) Connecting the ground wire of the turntabe to this termina wi normay minimize hum, but in some cases better resuts may be obtained with the ground wire disconnected. AX-59 ony PRE OUT/MAIN IN terminas Removing the jumper pins enabes this unit to independenty perform the functions of a contro ampifier and a power ampifier. These terminas are for connection of a signaprocessing system such as a graphic equaizer or sound processor. If a sound processor or other externa unit is connected between these terminas, the VOLUME contro of this unit can be used for overa adjustment of the eve of sound. To connect such a unit, remove the jumper pins from the PRE OUT/MAIN IN terminas, connect the inputs of that unit to the PRE OUT terminas and its outputs to the MAIN IN terminas. For detais, refer to the owner s manua incuded with the unit to be connected. Notes PRE OUT COUPLER MAIN IN If you wi not use the PRE OUT/MAIN IN terminas, never remove the jumper pins from these terminas. If removed, no sound wi be output from this unit. If you wi use this unit with an externa unit connected between the PRE OUT and MAIN IN terminas, make sure that the CD DIRECT AMP switch and the PURE DIRECT switch on the front pane are turned off. If you wi use this unit as a power ampifier, connect the outputs of an externa contro ampifier etc. to this unit s MAIN IN terminas. In that case, this unit s contros wi not function except the PHONES jack and the SPEAKERS switches, so use the contros on the externa contro ampifier to make voume adjustment etc.
OPERATIONS AX-59 7 1, 7 AX-9 7 1, 7 TO PLAY A SOURCE 1 VOLUME Seect the speakers to be used. SPEAKERS A B ON ON 5 OFF OFF 7 db Turn the power on. Set to the position. POWER * If you use two speaker systems, press both the A and B switches. 5 Pay the source. VOLUME Seect a desired input source. INPUT CD TAPE 1 TUNER TAPE 5 7 db Adjust to the desired output eve. * AX-59 ony If you seect turntabe as an input source ( position), you shoud confirm that the (MM/MC) switch on the rear pane is set to the position corresponding to the type of cartridge being used by the turntabe. (Refer to page.) 7 If desired, adjust the BASS, TREBLE, BALANCE and LOUDNESS contros, etc. (Refer to page 9 1.) To turn off the power Press the POWER switch again. 7
AX-59 1, 5 AX-9 1, 5 TO RECORD A SOURCE TO TAPE (OR DUB FROM A TAPE TO ANOTHER) 1 Seect the source to be recorded. AX-59 AX-9 Set the tape deck to be used for recording in the recording mode. REC OUT CD TAPE 1 TUNER TEAP REC OUT TAPE 1 CD TUNER TAPE 5 To monitor the sound to be recorded (or being recorded), seect the tape deck being used for recording with the INPUT seector. INPUT TAPE 1 CD TUNER Pay the source. TAPE Confirm the source by seecting it with the INPUT seector and turning up the VOLUME contro. TAPE TAPE 1 INPUT CD TUNER 5 7 VOLUME Notes If you want to enjoy another source whie recording, seect it with the INPUT seector. VOLUME, BASS, TREBLE, BALANCE, LOUDNESS contros, CD DIRECT AMP switch and PURE DIRECT switch settings have no effect on the materia being recorded. db
Adjusting the BALANCE contro Adjust the baance of the output voume to the eft and right speakers to compensate for sound imbaance caused from speaker ocation or istening room conditions. Seecting the SPEAKER system Because one or two speaker systems can be connected to this unit, the SPEAKERS switches aow you to seect speaker system A or B, or both at once. AX-59 AX-9 SPEAKERS BALANCE BALANCE A ON OFF B ON OFF L 5 5 R L 5 5 R Adjusting the BASS and TREBLE contros Adjusting the continuousy variabe LOUDNESS contro AX-59 BASS 5 5 TREBLE 5 5 This contro provides compensation for the human ears oss of sensitivity to high and ow-frequency ranges at ow voume. This contro is adjustabe to retain fu tona range at any voume eve. 1 AX-59 AX-9 AX-9 BASS BASS 5 5 : Turn this cockwise to increase (or countercockwise to decrease) the ow frequency response. TREBLE : Turn this cockwise to increase (or countercockwise to decrease) the high frequency response. TREBLE 5 5 LOUDNESS FLAT db 9 5 7 5 7 LOUDNESS FLAT db 9 5 7 VOLUME Set to the FLAT position. Set to the oudest istening eve that you woud isten to. db AX-59 LOUDNESS FLAT db 9 5 7 AX-9 LOUDNESS FLAT 5 7 db 9 Turn unti the desired voume is gained. 9
Using the PURE DIRECT switch You can enjoy the purest possibe sound from your audio sources by setting this switch so that the indicator iuminates. By doing so, the audio signas bypass the BASS, TREBLE, BALANCE and LOUDNESS contros, thus eiminating any aterations to the audio signas. AX-59 ony * The SUBSONIC FILTER switch and the PRE OUT/MAIN IN terminas are aso bypassed. PURE DIRECT Using the CD DIRECT AMP switch You can enjoy the purest possibe CD sound from your CD payer by setting this switch so that the indicator iuminates. By doing so, CD s input signas are sent to the buit-in ampifier specia for CD directy bypassing the INPUT seector, BASS, TREBLE, BALANCE and LOUDNESS contros, and then sent to the power ampifier. This signa routing reproduces the purest CD sound eiminating any aterations to the CD signas. AX-59 ony * The SUBSONIC FILTER switch and the PRE OUT/MAIN IN terminas are aso bypassed. CD DIRECT AMP Setting the SUBSONIC FILTER switch AX-59 ony If you set this switch to ON position, undesirabe utra-owfrequency signas caused by turntabe rumbe or warped records can be cut out without osing sound quaity. Note If both the CD DIRECT and PURE DIRECT switches are on, ony the CD DIRECT switch wi function. SUBSONIC FILTER ON OFF When you isten with headphones Connect the headphones to the PHONES jack. When istening with headphones privatey, set both the SPEAKERS A and B switches to the OFF position. PHONES Open/cose the contro door When it is not necessary to operate contros inside the contro door, cose the door. To cose the door AX-59 ony To open the door 1
REMOTE CONTROL TRANSMITTER The remote contro transmitter provided with this unit is designed to contro a the most commony used functions of the unit. If the CD payer, tuner, turntabe and tape deck connected to this unit are YAMAHA components designed for remote contro compatibiity, then this remote contro transmitter wi aso contro various functions of each component. KEY FUNCTIONS For Contro of This Unit Turns the power on/off. POWER PLAY/CUT SKIP PLAY CD SEARCH PAUSE/STOP DISC SKIP PRESET + A/B/C/D/E TUNER DIR A DECK A/B DIR B TAPE 1 PLAY TAPE Seects input source. REC/PAUSE STOP REC MUTE VOLUME + Turns the voume eve up/down. For Other Component Contro Identify the remote contro transmitter keys with your component s keys. If these keys are identica, their function wi be the same. On each key function, refer to the corresponding instruction on your component s manua. Starts/stops record pay on turntabe. POWER PLAY/CUT SKIP PLAY CD Contros tuner +: Seects higher preset station number. : Seects ower preset station number. A/B/C/D/E: Seects the page (A E) of preset stations. SEARCH PAUSE/STOP DISC SKIP PRESET + A/B/C/D/E TUNER DIR A DECK A/B PLAY DIR B TAPE 1 TAPE REC/PAUSE STOP REC MUTE + VOLUME Contros compact disc payer. * DISC SKIP is appicabe ony to compact disc changer. Contros tape deck. * DIR A, B and DECK A/B are appicabe ony to doube cassette tape deck. * For a singe cassette deck with automatic reverse function, pressing DIR A wi reverse the direction of tape running. 11
STANDBY mode (U.K. and Europe modes ony) Whie the power is on, pressing the POWER key on the remote contro transmitter switches the unit to the STANDBY mode. (In this mode, the indicator is haf iuminated.) Note The POWER switch on the front pane of this unit shoud be turned off when eft unused for a ong period of time. POWER POWER on mode POWER STANDBY mode NOTES ABOUT THE REMOTE CONTROL TRANSMITTER Battery instaation Remote contro transmitter operation range AX-59 AX-9 1 Remote contro sensor Battery repacement If you find that the remote contro transmitter must be used coser to the main unit, the batteries are weak. Repace both batteries with new ones. Notes Use ony AA, R, UM- batteries for repacement. Be sure the poarities are correct. (See the iustration inside the battery compartment.) Remove the batteries if the remote contro transmitter wi not be used for an extended period of time. If batteries eak, dispose of them immediatey. Avoid touching the eaked materia or etting it come in contact with cothing, etc. Cean the battery compartment thoroughy before instaing new batteries. Within approximatey m (19.7 feet) Notes There shoud be no arge obstaces between the remote contro transmitter and the main unit. If the remote contro sensor is directy iuminated by strong ighting (especiay an inverter type of fuorescent amp etc.), it might cause the remote contro transmitter not to work correcty. In this case, reposition the main unit to avoid direct ighting. 1
TROUBLESHOOTING If the unit fais to operate normay, check the foowing points to determine whether the faut can be corrected by the simpe measures suggested. If it cannot be corrected, or if the faut is not isted in the SYMPTOM coumn, disconnect the power cord and contact your authorized YAMAHA deaer or service center for hep. SYMPTOM The unit fais to turn on when the POWER switch is pressed. No sound. The sound suddeny goes off. Ony one side speaker outputs the sound. There is a ack of bass, and no ambience. Sound hums. Sound eve is ow. Sound eve is ow or sound is distorted whie paying a record on the turntabe. (For AX-59 ony) The INPUT seector wi not function though it is turned. Using the BASS, TREBLE, BALANCE, LOUDNESS contros and SUBSONIC FILTER switch (AX-59 ony) does not affect the tone. The remote contro transmitter does not work. The distance or range within which the remote contro transmitter can be used decreases. CAUSE Power cord is not pugged in or is not competey inserted. Incorrect output cord connections. Appropriate input source is not seected. The SPEAKERS switches are not set propery. Speaker connections are not secure. The protection circuit has functioned because of short circuit etc. Incorrect setting of the BALANCE contro. Incorrect cord connections. The + and wires are connected in reverse at the ampifier or speakers. Incorrect cord connections. No connection from the turntabe to the GND termina. The LOUDNESS contro is functioning. The (MM/MC) switch on the rear of this unit is set to the improper position. The CD DIRECT AMP switch is ON. The CD DIRECT AMP or PURE DIRECT switch is ON. Direct sunight or ighting (of an inverter type of fourescent amp etc.) is striking the remote contro sensor of the main unit. The batteries of this remote contro transmitter are too weak. REMEDY Firmy pug in the power cord. Connect the cords propery. If the probem persists, the cords may be defective. Seect an appropriate input source with the INPUT seector. Set the SPEAKERS switch which corresponds to the speakers to be used to the ON position. Secure the connections. Turning the unit off and then on wi reset the protection circuit. Adjust it to the appropriate position. Connect the cords propery. If the probem persists, the cords may be defective. Connect the speaker wires in the correct phase (+ and ). Firmy connect the audio pugs. If the probem persists, the cords may be defective. Make the GND connection between the turntabe and this unit. Set the LOUDNESS contro to the FLAT position. Reset the (MM/MC) switch to the proper position. Switch off the CD DIRECT AMP switch. The CD DIRECT AMP and PURE DIRECT switches must be switched OFF to use those contros. Change position of the main unit. Repace the batteries with new ones. 1
SPECIFICATIONS Minimum RMS Output Power per Channe ohms, Hz to khz,.15% THD...1W+1W ohms, Hz to khz,.% THD...1W+1W <AX-9> ohms, Hz to khz,.19% THD...5W+5W ohms, Hz to khz,.% THD...1W+1W Dynamic Power per Channe (by IHF Dynamic Headroom measuring method) /// ohms...1/17//9w <AX-9> /// ohms...1/15/15/w DIN Standard Output Power per Channe ( ohms, 1 khz,.7% THD) [Europe mode ony]...15w <AX-9>...1W IEC Power [Europe mode ony] ( ohms, 1 khz,.15% THD)...11W <AX-9> ( ohms, 1 khz,.19% THD)...1W Power Band Width ohms, 5W,.% THD...1 Hz to 5 khz <AX-9> ohms,.5w,.% THD...1 Hz to 5 khz Damping Factor ohms, Hz khz...more than <AX-9>...more than Damping Factor (DIN) ohms, Hz [Austraia, U.K. and Europe modes]...more than 1 <AX-9>...more than 1 Maximum Power (EIAJ) 1 khz, 1% THD [Genera mode ony] ohms...15w ohms...17w <AX-9> ohms...1w ohms...15w Input Sensitivity/Impedance MM...5 mv/7 k-ohms MC <AX-59 ony>...1 µv/ ohms CD/TUNER/TAPE/...15 mv/7 k-ohms MAIN IN <AX-59 ony>...1.v/1 k-ohms Maximum Input Signa (1 khz,.7% THD) MM...15 mv MC...1 mv Maximum Input Signa (1 khz,.% THD) <AX-9> MM...115 mv Output Leve/Impedance REC OUT...15 mv/7 ohms PRE OUT...1.V/1 k-ohms <AX-9> REC OUT...15 mv/7 ohms Headphone Jack Rated Output/ Impedance Output Leve ( ohms,.15% THD)...V Impedance... ohms <AX-9> Output Leve ( ohms,.19% THD)...V Impedance... ohms Frequency Response ( Hz to khz) CD/TUNER/TAPE/...±.5 db MAIN IN <AX-59 ony>...±.5 db RIAA Equaization Deviation ( Hz to khz) MM...±. db MC <AX-59 ony>...±.5 db Tota Harmonic Distortion ( Hz to khz) MM to REC OUT (V)...% MC to REC OUT (V)...7% CD/TUNER/TAPE/ to PRE OUT (1V)...5% CD/TUNER/TAPE/ to SP OUT (5W/ ohms)...% <AX-9> MM to REC OUT (V)...% CD/TUNER/TAPE/ to SP OUT (.5W/ ohms)...% Intermoduation Distortion (Rated output/ ohms)...1% Signa-to-Noise Ratio (IHF-A Network) MM (5 mv Input Shorted)... 9 db MC (5 µv Input Shorted)... 7 db CD/TUNER/TAPE/ (Input Shorted) (CD DIRECT AMP; ON)... 11 db <AX-9> MM (5 mv Input Shorted)... db CD/TUNER/TAPE/ (Input Shorted) (CD DIRECT AMP; ON)... 11 db Residua Noise (IHF-A Network) (CD DIRECT AMP; ON)...5 µv (PURE DIRECT; ON)...9 µv Channe Separation (Vo. db) MM/MC (Input Shorted 1 khz/1 khz)...75 db/ db CD/TUNER/TAPE/ (Input 5.1 k-ohms Terminated 1 khz/1 khz)...5 db/5 db <AX-9> CD/TUNER/TAPE/ (Input 5.1 k-ohms Terminated 1 khz/1 khz)...5 db/5 db Tone Contro Characteristics BASS: Boost/cut...±1 db ( Hz) Turnover Frequency...(5 Hz) TREBLE: Boost/cut...±1 db ( khz) Turnover Frequency...(.5 khz) Fiter Characteristics <AX-59 ony> SUBSONIC FILTER...15 Hz, 1 db/oct Continuous Loudness Contro Attenuation... db (1 khz) (Leve reated equaization) Gain Tracking Error ( to db)... db Power Suppy [U.S.A. and Canada modes]...ac 1V, Hz [Austraia and U.K. modes]...ac V, 5 Hz [Europe mode]...ac V, 5 Hz [Genera mode]...ac 11/1//V, 5/ Hz Power Consumption [U.K., Europe, Austraia and Genera modes]...1w <AX-9> [U.S.A. mode]...19w [Canada mode]... VA, 5W [U.K., Europe, Austraia and Genera modes]...1w AC Outets [U.S.A., Canada, Europe and Genera modes] SWITCHED OUTLETS...1W max. tota [U.K. and Austraia modes] 1 SWITCHED OUTLET...1W max. tota Dimensions (W x H x D)...5 x 1 x.5 mm (17-1/ x 5-/ x 15-5/1 ) <AX-9>...5 x 1 x mm (17-1/ x 5-/ x 15-/1 ) Weight...1. kg ( bs. 1 oz.) <AX-9>...9. kg ( bs. oz.) Accessories...Remote contro transmitter Batteries Specifications subject to change without notice. 1
YAMAHA ELECTRONICS CORPORATION, USA ORANGETHORPE AVE., BUENA PARK, CALIF. 9, U.S.A. YAMAHA CANADA MUSIC LTD. 15 MILNER AVE., SCARBOROUGH, ONTARIO M1S R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. -, D-5 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP7 CROISSY-BEAUBOURG 771 MARNE-LA-VALLEE CEDEX, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 5, VÄSTRA FRÖLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD. 17- MARKET ST., SOUTH MELBOURNE, 5 VIC., AUSTRALIA VS 975