OC7171A-T START-STOP-RESET TIMER

OC7171A-T_GBM_21012 OC7171A-T START-STOP-RESET TIMER Owner s Manual ORBIT CONTROLS AG Zürcherstrasse 137 CH-8952 Schlieren/ZH Tel: + 41 44 730 2753 Fax: + 41 44 730 2783 info@orbitcontrols.ch www:orbitcontrols.ch

SICHERHEITSHINWEISE Das Gerät muss mit selbständiger oder gemeinsamer Sicherung (Schutzschaltern) gesichert werden. Für die einzuhaltenden Sicherheitshinweise s. auch EN 61 010-1 + A2. Das Gerät ist nicht explosionsgeschützt! TECHNISCHE NORMEN Die Anzeigen der Typenreihe OC7171 entsprechen der Europäischen Verordnung 89/336/EWG. Sie erfüllen die Forderungen der folgenden europäischen und tschechischen Normen: EN 55 022, Klasse B EN 61000-4-2, -4, -5, -6, -8, -9, -10, -11. Das Gerät ist zur unbeschränkten Anwendung in Landwirtschaft und Industrie geeignet. ANSCHLUSS Die Stromzuleitung von der Hauptspannungsquelle muss von den Messleitern getrennt verlegt werden. Hersteller-Manufacturer ORBIT CONTROLS AG Zürcherstrasse 137 CH-8952 Schlieren/ZH Switzerland Tel: + 41 44 730 2753 Fax: + 41 44 730 2783 info@orbitcontrols.ch www:orbitcontrols.ch Owner s manual 2

Vor dem Einschalten Überzeugen Sie sich, ob Ihre Sendung das richtige Gerät Orbit Controls Modell OC 7171A-T beinhaltet, einschliesslich einer Betriebsanleitung OC 7171A-T. Vor dem Einschalten des Gerätes überprüfen Sie die Anschlüsse und die Versorgungsspannung. Ein falsch angeschlossenes Gerät kann beschädigt werden und damit auch die mitverbundene Folgeelektronik. Für falsche Handhabung wird jede Haftung abgelehnt. ZU BEACHTEN Dieses Gerät wurde sorgfältig verpackt. Falls es bei Ihnen in beschädigtem Zustand eintrifft, benachrichtigen Sie unverzüglich den Orbit Controls Kundendienst (Tel: +41 44 730 2753 oder Fax: +41 44 730 2783) und nehmen Sie einen Schadenrapport auf, welchen Sie auch von der Transportgesellschaft unterschreiben lassen. Bewahren Sie bitte das Verpackungsmaterial für eventuelle Reklamationen auf. Unpacking Instructions Remove the Packing List and verify that you have received all equipment, including the following: Orbit Controls Model OC 7171A-T Programmable Controller. Operator's Manual OC 7171A-T. If you have any questions about the shipment, please call the Orbit Controls Customer Service Department. NOTE When you receive the shipment, inspect the container and equipment for signs of damage. Note any evidence of rough handling in transit. Immediately report any damage to the Orbit Controls customer service, Phone +4144 730 2753 or Fax +4144 730 2783 and to the shipping agent. The carrier will not honour damage claims unless all shipping material is saved for inspection. After examining and removing contents, save packing material and carton in event the reshipment is necessary. Owner s manual 3

INDEX Programmable Timer OC7171A-T Page 5 1 KEYBOARD 6 2 MENU 6 3 MENU STEPS 7 4 SPECIFICATIONS 7 5 OC7171A-T TERMINALS 8 6 SIGNAL CONDITIONER 8 7 OPTIONS BOARD 9 8 H-TEST and CALIBRATION 10 9 BURST TEST and recommended CONNECTIONS 11 Owner s manual 4

PROGRAMMABLE TIMER OC7171A-T Start-Stop-Reset Timer Six Digits Display Parameter Memory Four Set Point Relays Two Analogue Outputs RS232 and RS485 Mains or DC Supply Model OC7171A-T is a 6 digit Timer with three inputs START, STOP and RESET and two programmable functions as a Timer with a display incrementing between the Start and the Stop signal or as a Timer with display refreshing with the Stop Signal. The Timer Mode is selectable in the Menu Step Fn dsp as Cont or St-St. In the Cont Timer Mode the display increments after the START signal and stops with the STOP signal. The Time value remains at the display. With the next START the display continues to increment by adding the new time value to the previous one. The display can be set to Zero (or to a programmable PRESET) with the RESET signal. In the St-St Timer Mode the instrument starts the operation with START and cumulates the time increments in internal register. After the STOP the Time will be displayed. After next START the increments are cumulated internally and added to the previous increments. After a STOP signal the display shows the addition of the first and the second measurement. A control signal at the RESET input resets the internal counter to zero (not the display). The internal Time Base generates increments 1mS increments. By using the dscale in the menu, the increments can be set for 10mS, 100mS, 1s or 10s. When the RESET input is hard wired with the START input at the terminal block, the counter will be set to Zero after each START. Owner s manual 5

1 KEYBOART MENU ACK UP DOWN SET The key MENU opens the program menu. The required parameter will be confirmed with ACK and set with UP or DOWN. The flashing digit - Cursor can be positioned with ACK. The sign and the decimal point can be set when the flashing digit is positioned outside the display view (no flashig digit visible). The key UP sets the decimal point, DOWN the sign. The key SET terminates the programming mode and the display returns into the measuring mode. 2 MENU (Instrument with all Options installed) SP1 Set Point 1. HSt 1 Hysterese SP1. SP2 Set Point 2. HSt 2 Hysterese SP2. PASS Correct Password permits entry into the menu. FnDSP Display function Cont or St-St PrESET 6 digit display offset with decimal point and sign SCALE 6 digit multiplication of the internal 1mS Time Base. In the Time Measuring Mode the SCALE to be set 1. dscale Dividing constant selectable from :1 to :100 000. dscale=1 =>1mS, dscale=10 =>10mS, dscale=10 => 100mS, dscale=1000 => 1Sek OrdEr Decimal Point Display selection C.ddddd to CCCCCC. CCCCCCC Floating point mode. Aout L Display value for Analogue Output 0/4 ma and 0V. Aout H Display value for Analogue Output 20mA and 10V. Fn Anl Function of the Analogue output: OFF not activated 04 20 directly proportional 20 04 inverted baud Baud rate. rs Adr Address 0 activates RS232. One of addresses 01-31 activates RS485. St PASS Password selection from 20 memorized combinations. StArt Measure Mode SET Termination of the programming mode, start of the measuring mode. Owner s manual 6

3 MENU STEPS (Instrument without Options) PASS FnDSP PrESET SCALE dscale OrdEr St PASS StArt SET Correct Password permits entry into the menu. Display function Cont or St-St 6 digit display offset with decimal point and sign 6 digit multiplication of the internal 1mS Time Base. In the Time Measuring Mode the SCALE to be set 1. Dividing constant selectable from :1 to :100 000. dscale=1 =>1mS, dscale=10 =>10mS, dscale=10 => 100mS, dscale=1000 => 1Sek Decimal Point Display selection C.ddddd to CCCCCC. CCCCCCC Floating point mode. Password selection from 20 memorized combinations. Measure Mode Termination of the programming mode, start of the measuring mode. 4 SPECIFICATIONS DISPLAY: 0... ± 999999, red, 7 Segments, 14.7 mm. INPUTS: Positive Logic 5V CMOS, protected to 28V. Input 15: START Input 13: STOP Input 11: RESET PRESET: SCALE: dscale: OUTPUTS: ORDER: Display Offset 0 to ± 999999 with decimal point and sign. The Preset can be entered into the display with external positive logic signal 5-28V at Terminal 11. 6 digit multiplicating constant with decimal point and sign. In the Time Measurement Mode to be set to 1. Dividing constant of the SCALE. Setable from :1 to :100 000. For Display Increments of 1 Second select dscale=1000 Analogue Output: 0/4-20mA and -10 +10V, selectable as direct acting 04-20 or inverting 20-04 or disabled OFF. Response Time 100ms. Digital Output: RS232 two terminals and RS485 four terminals. 8Bit, No Parity, 1Start, 1 Stop, 1200-19200 bd. Set Points: 2 or 4 Relays 5A-230VAC, or open collectors 48V-100mA. Decimal Point selection (Display resolution): X.XXXXX to XXXXX. SUPPLY: 115/230V ±10%, 50-60Hz, 6VA. Option: 9-36 V DC, 4 W. CABINET: ANSCHLÜSSE: DIN 48x96mm, Depth behind the lens 100mm. Panel cut-out 45x90 mm. IP65 protection from the front. Pluggable screw terminals. Owner s manual 7

5 OC7171A-T TERMINALS Instrument with all Options installed (Standard Inputs) 6 SIGNAL CONDITIONER Headers H1, H2, H3 configure the input signals. The Header H1 activates the three inputs A, B, C and the corresponding three GND. The Header H2 activates the optional Inputs A-A, B-B, C-C for Line Driver Control. HEADER POSITIONS Line Driver Inputs TTL Inputs Owner s manual 8

7 OPTIONS BOARD The Options Board contains two Analogue Outputs 4-20mA and -10 +10V, two serial Data Ports RS232 and RS485 and two Set Points SP3 and SP4. Potentiometers P1, P2, P3, P4 are for calibration of the Analogue Outputs. The calibration can be activated in the H-TEST ( 8) Sub Menu. Owner s manual 9

8 H-TEST and CALIBRATION Service Menu H-TEST is available for Testing, Calibration of the Time Base and Calibration of the Analogue Outputs. During the instrument is switched-on press the key MENU until the display shows HtESt. The test steps can be advanced with the key MENU. Return steps are possible with SET. Segments: HCF.128 All segments will be illuminated. With the key MENU the HCF-Function is activated. The HCF-number defines the Range of the Menu. HCF 128 defines Instruments without options. Each Option has a binary number added to 128: 1 SP1, HSt1 16 Analogue output 2 SP2, HSt2 32 baud 4 SP3, HSt3 64 rs-adr 8 SP4, HSt4 Combinations define more build-in options, such as: HCF.0 Without Menu, the menu is completely blocked. HCF.144 Menu (128) and Analogue Output (16). HCF.240 Menu (128), Analogue Output (16), Baud Rate (32), Address (64). After the selection press ACK to store the settings. Calibration: By applying the key MENU again the calibration of the Time Base for the Frequency Measurement is activated. The display shows CAL.XXX whereas XXX a three digit number is. This code can be set with UP or DOWN and represents scaling of the internal X-tal Time Base. A value of 10 increments represents 0.1Hz difference at input frequency of 10 khz and a display value of 10000.0. After the selection press ACK to store the settings. The calibration has been precisely set during the production at the factory. Set Points: By applying the key MENU again the Set Points SP1-SP4 are energized and the corresponding LEDs illuminated. Analog Output Selection: dac12 or dac16 will be selected in accordance with the build-in hardware option. Analogue Outputs: By applying the key MENU again the Analogue Outputs (Option) are activated. The output signals are available at the instrument s terminals and can be calibrated. The display shows: Out -10, Out -5, Out 0, Out 5, Out 10. By applying the key MENU again the display shows StArt and switches into the measuring mode. Owner s manual 10

9 BURST TEST and recommended CONNECTIONS Tester: Burst-Surge Generator HILO, Model CE-Tester Datum: 15. June 2000 E.U.T.: OC7171, SN: 200615, Supply 230VA Mode: UdiC F Frequency Counter, SCALE = 1, OrdEr = CCCCCC Input: 99998 Hz Display: 99998 9.1 Test Conditions CE-Norms: IEC 801-4 IEC 1000-4-4 EN 50052-1 9.2 Test Set - Up 9.3 Test Results Zone 1: 2kV Burst Display 99998 no change Zone 2: 2kV Burst Display 99998 no change Technician: Oliver Matthews 15. June 2000 CE Approval No: 409/18-30/2001-4568 from 12.6.2001 VTUE Praque. Owner s manual 11