Newtown Township Municipal Renovation and New Public Works. Audio Video Bid Specifications

Newtown Township Municipal Renovation and New Public Works Audio Video Bid Specifications

Table of Contents Vendor Requirements 2 Meeting Room 91.3 Hard Interview Rooms 129 & 131.5 Room 111..6 Room 122..7 Room 139..9 Room 147..10 Room 149..11 Room 153..12 Room 218..13 Rooms 085A, 108, 204.15 Room 117..16 Rooms 119, 120, 121, 150, 151, Public Works 304, 305 17 Room 207 18 Rooms 211.19 Rooms 212.20 Public Works 306...21 1

Vendor Requirements for All Rooms: The vendor is responsible for all miscellaneous items, including patch cables, rack mounting accessories, and parts not listed in the required hardware list. All video wiring must be installed with shielded, plenum rated CAT6 or better. If a data connection is not at the necessary location the vendor is responsible to pull the proper data wiring to match the existing network infrastructure, and naming convention. All Extron equipment will be connected to the existing network, allowing for mobile device control. Vendors are expected to provide full system wiring diagrams with equipment serial numbers. 2

Room: Meeting Room 91 Video Distribution: There will be five full swing arm mounted 75 LED HDTV controllable displays throughout the room capable of showing any room inputs. There will be an additional zone in the community room for meeting over flow that will have an Epson short throw projector shining onto an 87 SMART board. Additionally, the community room short throw projector will have a local wall plate with a 35 HDMI and USB that is only viewable on the projector in the community room. The USB cable is for SMART board interactivity. There will be a matrix switcher located in the equipment rack that will distribute video signals to each output device via shielded twisted pair. There will be two HDMI input wall plates that will transport the video signal back to the switcher via shielded twisted pair. A Barco Clickshare wireless presentation will be mounted behind the closest display to the front of the room. The video signal from the Clickshare will be sent back to the Matrix switcher via shielded twisted pair. There will be a dedicated PC that will live in the equipment rack provided by Newtown Township. A 12 meter USB extender will run back into the ceiling of the main room to extend the signal for a wireless keyboard and mouse. Vendors are responsible for all miscellaneous patch cables. A brightsign digital signage player will be installed on the library wall mounted projector. Audio Distribution: There will be twelve Shure Microflex wireless boundary microphones and two Shure Microflex hand held microphones for in-room sound reinforcement and audio recording of meetings. The microphones will transmit wirelessly to two Shure Access point transceivers mounted in the room. The microphone audio will be sent to an in-rack Extron digital signal processor via a Dante network that will be setup for the room. The DSP will feed a QSC amplifier which will power twelve 4.5" Coaxial in-ceiling loudspeakers. There will be two audio zones that can be combined or act independently. One in the main meeting room and the other in the community room overflow area. The DSP will also send audio to a Denon network recorder that will be configured to save the recording files to a network storage space. For ADA compliance, there will be a Williams Sound FM assistive listening system installed for the hearing impaired. Control: There will be a 7 wall mounted Extron touch panel located in the main room. This touch panel will power off and on each display and control the independent source selection of each display. It will control audio volume levels, audio zone selection, and audio recording. There will be a 5 wall mounted Extron touch panel located in the community room section of the room. This touch panel will power off and on the wall mounted projector and control the source selection. This panel will also control volume for the speakers in that zone. 3

Required Hardware (No Substitutions) QT 1 Epson V11H744520 Epson 685W Projector 1 Epson V12H777020 Projector Wall Mount 1 SMART SBM685 SMART 87" Interactive Whiteboard, 16x10 Widescreen Format 1 SMART EWY3-SBM SBM600 3 Year Warranty Extension 5 Samsung LED HDTV 75"LED HDTV Controllable 5 Chief TS525TU Full Swing Display Mounts 12 Shure MXW6/C=-Z10 Boundary Transceiver, Cardioid 2 Shure MXW2/SM58=-Z10 Handheld Transmitter with SM58 Microphone 2 Shure MXWAPT8=-Z10 8-CH ACCESS POINT TRANSCEIVER 2 Shure MXWNCS8 8-CH NETWORKED CHARGING STATION 1 Extron 60-1211-10 DMP 128 AT 1 QSC PLD4.2-NA 4 Channel 1600 Watt Amplifier 12 Atlas FAP43T-W 4.5" Coaxial In-Ceiling Loudspeaker 2 Extron 60-1421-12 DTP T HWP 4K 231 D 1 Extron 60-1382-01 DTP CrossPoint 86 4K 1 Extron 60-1438-01 DTP HD DA8 4K 230 7 Extron 60-1271-13 DTP HDMI 4K 230 Rx 3 Extron 60-1382-01 DTP HDMI 4K 230 Tx 1 Extron 60-1418-01 IPCP Pro 550 1 Extron 60-1185-02 TLP Pro 520M 1 Extron 60-1394-02 TLP Pro 720M 2 Extron 60-604-02 RSB 129 Rack Shelf 2 Extron 60-190-01 RSU 129 Rack Shelf 1 Barco CSE-200 ClickShare 1 Chief NE1D28P Plexiglas Door for 28U E1 Rack 1 Chief NE1F2823 28U, 23" Deep E1 Series Rack 1 Chief NAC25H 2.5" Heavy Duty Rack Casters 2 Middle Atlantic PD-915R-PL Rack Mount Surge Protector 1 Denon DN700R Network SD/USB Recorder 1 D-Link DGS-12--10P PoE Switch 1 Williams Sound PPA 457 PRO FM Assistive Listening System 1 C2G 41366 35ft Active High Speed HDMI Cable In-Wall, CL3-Rated 2 C2G 38998 12m USB A/B Active Cable (Center Booster Format) (39.4ft) 1 C2G 40110 75ft 3.5mm Stereo Audio Cable With Low Profile Connectors M/M - In-Wall CMG-Rated 1 USB Wireless Keyboard and Mouse 1 Brightsign LS423 signage player Digital signage player 4

Room: Hard Interview Rooms 129 and 131 Outputs The goal of the interview rooms is to capture both audio and video to a reliable recording source. Both rooms will have a Shure hanging microphone in the ceiling, and one camera securely mounted in the designated corner for optimal video capture. An Extron touch panel with a USB port for additional recording will be mounted outside of the interview room. All devices will be connected to an Extron recording device that will be stored in records 114. A wall mounted cabinet will be installed, and used for housing the recording devices, distribution amps, surge protectors, POE adapters, and pre-amps. Interview Room Feeds will be wired using all shielded CAT6 Plenum rated wiring. Installers will be responsible for configuring all devices to the network, and configuration of the Extron SMP 351 recording configuration. Vendors are responsible for all miscellaneous patch cables. Interview rooms 129 and 131 will be wired to the below HDMI inputs on these offices: Conference Room 147 Chief Office 111 Lieutenant 121 Required Hardware (No Substitutions) All below items are QTY 2, and bold items are marked in the cell for quantity. Additional 1x8 video distribution amp will be used for distributing security camera feeds. Extron 60-1594-01 SMP 111 Recording Media Processor Extron 60-1598-01 RCP 101D Remote Control Panel for recording Extron 60-1471-12 USB Extender PLUS series Tx Extron 60-1471-13 USB Extender PLUS series Rx Extron 60-604-02 RSB129 Shelf for rack mounting Equipment Marshall AV-CV-505-M Mini Camera with appropriate lens and mounting hardware Atlas TSD-ML11 1x1 Mic/Line Level Pre-Amp TSD- Power Supply for Pre-Amp Atlas PS24V250MA Atlas TSD-RMK Rack mount kit for Atlas Pre-amp Shure MX202BP/N Mircroflex overhead mic with NO Cartridge/unterminated ends (black) Shure R183B Omni-Directional cartridge (black) Shure RK183WS Black-snap fit windscreen (pkg4) Middle Atlantic PD-915R-PL 15a Rack mount surge strip. Extron QTY 3 60-1438-51 1x8 HDMI in to DTP Output for video distribution (330ft model) Middle Atlantic QTY 1 CWR-26-26PD Wall Mounted cabinet: 26U x26" deep 5

111 (Chief Lunn s Office) A 50 LED HDTV display will be mounted on the designated wall with a Chief tilting mount kit. This display will have a total of five inputs connected to the display, and will require an Extron brand HDMI switcher. The switcher will be controlled via an Extron MLC controller (installed on designated wall). The inputs for this display are listed below, and the only requirement for this section of the proposal is an in-room HDMI connection terminated into a wall plate at the user s desk for extended desktop purposes. Three Extron RX devices will also be part of this room to receive the feed of the interview rooms, and security cameras. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. : 1. In room HDMI 2. Feed from Interview Room 1 3. Feed from Interview Room 2 4. Feed from Security Cameras (holding cells) 5. Cable TV input Required use of parts listed below: Samsung LED HD TV 50"LED HDTV Chief MTM1U Medium Fusion Tilt Mount C2G #39710 HDMI Decora Wall Plate Extron 60-1331-13 HDMI over Cat6 Rx Extron 60-1484-01 HDMI Switcher (needed for inputs on TV) Extron 60-1470-02 MLC Plus 200 Extron 70-212-01 MBU 123 6

Room 122 (Conference Room) The Goal of Room 122 is to create an easy to use reliable video and audio conferencing room. This room will have an Extron Cable Cubby located in the table for easy user connectivity. The cables will consist of HDMI, VGA w/3.5 audio, and electrical outlets with USB charging ports. All wiring will be terminated at the in-room credenza provided by the vendor. The credenza will be a 2 bay setup with half for AV, and the other half for basic storage. The credenza will be used to house an in-room PC supplied by Newtown Township (this will be where the USB from the interactive projector and Vaddio USB 3.0 camera will be connected), surge protector, scaler switcher, POE switch, Audio conferencing system and other miscellaneous in room equipment. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. Displays This conference room will have a main display utilizing a 75 LED HDTV. This display will be mounted at the designated location provided by Newtown Township. We will utilize one input on this display. All switching will take place at the IN1608. Audio A total of four ceiling mounted speakers will be installed, and connected to the Extron scaler/switcher with the built-in amp. The volume will be controlled using the Extron touch panel. Two ceiling mounted microphones will be installed at the best location for audio and video calls. Conferencing Conference room 122 will have the ability to make audio calls by adapting to the current VOIP infrastructure. Vendor shall install 2 hanging microphones, and speakers in this room for making these calls. The backend equipment will be a Clearone Converge Pro 2, and all calls will be dialed utilizing the Extron touch panel. All video calls will be made utilizing a Vaddio Conference Shot 10 PTZ camera. This camera will be connected to the in room OSE PC. End user will utilize SAS for these calls. All user inputs will be installed in a cable cubby at the table. Vendors will be responsible for installing the cubby. A template must be provided prior to the install for the furniture manufacturer to make the cutout. The cable cubby will have power with USB, data, VGA 3.5 and HDMI. All other devices will live in the credenza/rack in the room. 7

Required use of parts listed below: (No Substitutions) Extron 60-1238-13 IN1608 IPCP MA 70 Extron 70-1046-02 Cable Cubby 700 Extron 60-1697-01 AC+USB 224 US Extron 70-1049-80 Cable Cubby 500 CCB & Cable Cubby 700 Routing Template Extron 70-100-11 Two RJ-45 Female to Female Barrels Extron 60-1185-02 TLP Pro 520M Extron 60-1271-13 DTP HDMI 4K 230 Rx Samsung LED HDTV 75" Display Chief XSM1U Fixed Wall Mount Atlas FAP63T Ceiling Mounted Speakers Middle Atlantic 2 Bay Credenza D-Link DGS-12--10P PoE Switch Clearone 910-001-013-W Ceiling Mic Array Clearone 910-3200-003 Converge Pro2 128V Vaddio 999-9990-000W ConferenceShot Camera Middle Atlantic PD-915R-PL Rackmount Power, 9 Outlet, 15A, Basic Surge Middle Atlantic U1 Utility Rackshelf, 1 RU, 10.75"D Middle Atlantic *FEB1 Steel Blank Panel Middle Atlantic CAB-COOL Cabinet Cooler, 20 CFM 8

Rooms 139 Processing Room 139 will have a 40"LED HDTV mounted to the wall via medium tilt mount. The built-in speakers from the display will be used for room audio. The display will be connected to a wall mounted PC provided by Newtown Township to be used in remote arraignments. Mounted on top of the display will be a Logitech webcam and microphone combination. The webcam will be connected to the PC via USB cable. Vendor is responsible programming and commissioning of all installed equipment. 1. PC Required use of parts listed below for each room: (No Substitutions) 1 Samsung UN40J5200AF 40"LED HDTV 1 Chief MTM1U Medium Fusion Tilt Mount 1 Logitech C930e Webcam with HD 1080p Camera 9

Room 147 (Conference Room) Conference Room 147 will have a wall mounted, controllable 75 display. Mounted on the wall behind the display will be a dedicated room PC provided by Newtown Township. Also, mounted behind the display will be an Extron four input HDMI switchers to allow for remote viewing of the two interview room camera feeds and the building NVR. The remote video feeds will require HDMI over twisted pair receivers. The built-in speakers from the display will be used for room audio. An HDMI cable will run from the display and terminated into a wall plate for an additional input into the system. A 5 touch panel will be installed on the wall to control the power of the display, volume control, and input selection. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. Vendor will supply 1 Bay Credenza to house equipment. 2. Dedicated PC 3. Wall Plate HDMI 4. Interview Room 1 5. Interview Room 2 6. NVR Required use of parts listed below: (No Substitutions) Extron 70-212-01 MBU 123 Extron 60-1484-01 SW4 HD 4K Extron 60-1284-02 TLC Pro 521M Extron 60-1331-13 DTP HDMI 4K 330 Rx D-Link DGS-12--10P PoE Switch Samsung LED HDTV 75" Display with RS232 Chief XSM1U Fixed Display Mount C2G #39710 HDMI Wall Plate Middle Atlantic C5-FF27-1 Middle Atlantic C5-VENT1-SM C5 Series Frame, 1 Bay, 27" Deep C5 Silver Vent Middle Atlantic C5K1A1SSTNMZP001 TLAM Wood Kit 10

Room 149 (Squad Room) Vendors will be responsible for installing a 60 LED HDTV display. The main purpose for this feed is to display video from the holding cell camera system. Vendors will be responsible for pulling shielded CAT6 from the splitter in Records 114 to this display. An additional input will also be installed for users to connect devices within the room. Vendors will install an HDMI wall plate, and assume the use of 35 HDMI cable. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. Displays A Samsung 60 LED HDTV display with Chief mounting hardware Audio The speakers in the TV will be utilized for audio. HDMI feed from the holding cell cameras, and an HDMI input wall plate in the room. Required use of parts listed below: (No Substitutions) Samsung LED HD TV 60"LED HDTV Chief LTM1U Large Fusion Micro-Adjustable Tilt Wall Mount C2G #39710 HDMI Decora Wall Plate Extron 60-1331-13 HDMI over Cat6 Rx 11

Room 153 (Break Room) Vendors will be responsible for installing a 50 LED HDTV display. The main purpose for this TV is to display video from the holding cell camera system. Vendors will be responsible for pulling shielded CAT6 from the splitter in Records 114 to this display. An additional input will also be installed for users to connect devices within the room. Vendors will install an HDMI wall plate, and assume the use of 35 HDMI cable. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. Displays A Samsung 50 LED HDTV display with Chief mounting hardware Audio The speakers in the TV will be utilized for audio. HDMI feed from the holding cell cameras, and an HDMI input wall plate in the room. Possibly a CABLE TV input as well Required use of parts listed below: (No Substitutions) Samsung LED HD TV 50"LED HDTV Chief MTM1U Medium Fusion Tilt Wall Mount C2G #39710 HDMI Decora Wall Plate Extron 60-1331-13 HDMI over Cat6 Rx (330ft) 12

Room 218 (Conference Room) The Goal of Room 218 is to create an easy to use reliable video and audio conferencing system. This room will have an Extron Cable Cubby located in the table for easy user connectivity. The cables will consist of HDMI, VGA w/3.5 audio, and electrical outlets with USB charging ports. All wiring will be terminated at the in-room credenza provided by the vendor. The credenza will be a two-bay setup with half for AV, and the other half for basic storage. The credenza will be used to house an in-room PC supplied by Newtown Township (this will be where the USB from the interactive projector and Vaddio USB 3.0 camera will be connected), surge protector, scaler switcher, POE switch, Audio conferencing system and other miscellaneous in room equipment. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. Displays This conference room will have a main display utilizing an Epson interactive projector with the image projected onto a 100 diagonal whiteboard. On the opposite wall a 60 LED HDTV display will be mounted, and utilized for only cable TV input. This display will be connected to the rack where the cable box will be stored, and all control will take place utilizing the touch panel. Audio A total of 4 ceiling mounted speakers will be installed, and connected to the Epson scaler/switcher with the built-in amp. The volume will be controlled using the Extron touch panel. Conferencing Conference room 218 will have the ability to make audio calls utilizing the existing VOIP phone system. Vendor will install two hanging microphones, and speakers in this room for making these calls. The backend equipment will be a Clearone Converge Pro 2, and all calls will be dialed utilizing the Extron touch panel. All video calls will be made utilizing a Vaddio Conference Shot 10 PTZ camera. This camera will be connected to the in room OSE PC. End user will utilize their own SAS for video conferencing calls. All user inputs will be connected in a Cable Cubby at the table. Vendors will be responsible for installing the cubby. A template must be provided prior to the install for the furniture manufacturer to make the table hole. The cubby will have power with USB, data, and HDMI. All other devices will live in the credenza located in the room. 13

Required use of parts listed below: (no Substitutions) Extron 60-1238-13 IN1608 IPCP MA 70 Extron 70-1046-02 Cable Cubby 700 Extron 60-1697-01 AC+USB 224 US Extron 70-1049-80 Cable Cubby 500 CCB & Cable Cubby 700 Routing Template Extron 70-100-11 Two RJ-45 Female to Female Barrels Extron 60-1185-02 TLP Pro 520M Extron 60-1271-13 DTP HDMI 4K 230 Rx Extron 60-1271-12 DTP HDMI 4K 230 Tx Sharp LED HD TV 60" Display Chief LTM1U Tilt Wall Mount Atlas FAP63T Ceiling Mounted Speakers Middle Atlantic Pre-configured C5 Series Credenza, 2 Bay (match finish from Newtown Township furniture) D-Link DGS-12--10P PoE Switch Clearone 910-001-013-W Ceiling Mic Array Clearone 910-3200-003 Converge Pro2 128V Vaddio 999-9990-000W ConferenceShot Camera Middle Rackmount Power, 9 Outlet, 15A, Basic Surge Atlantic PD-915R-PL Middle Utility Rackshelf, 1 RU, 10.75"D Atlantic U1 Middle Steel Blank Panel Atlantic *FEB1 Middle Cabinet Cooler, 20 CFM Atlantic CAB-COOL C2G 53880 USB 2.0 Over Cat5 Superbooster Dongle Kit Epson V11H728022 EPSON BrightLink 696Ui Interactive Projector Epson V12H777020 Projector Wall Mount Epson V12H831000 EPSON 100" White Board/Dry Erase 14

Rooms 085A, 108, 204 (Signage Systems for Lobby) Library Display Vendors will be responsible for installing a 50 LED HDTV display in the designated waiting areas. The display will be securely mounted to the wall, and will be connected to the signage player that will be mounted behind the display. Vendors will also be responsible for pulling data from the display to the network closet. Vendors are not responsible for content creation, but will be responsible for configuring the players on the network, and installing management software. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. In the Library the vendor will use the existing display however all the other wiring and hardware will be provided. Displays A Samsung 50 LED HDTV display with Chief mounting hardware Audio The speakers in the TV will be utilized for audio. The signage player will be connected using the HDMI input of the display. Required use of parts listed below: (No Substitutions) Samsung LED HD TV 50"LED HDTV Chief MTM1U Medium Fusion Tilt Mount Brighsign LS423 signage player Digital Signage Player 15

Room 117 (Outside Agency) Vendors will be responsible for installing a 60 display on the designated wall. This display will have one cable connected via HDMI and terminated to a wall plate for user connected devices. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. Displays A Samsung 60 LED HDTV display with Chief mounting hardware Audio The speakers in the TV will be utilized for audio. A single gang wall plate will be connected using the HDMI input of the display. Required use of parts listed below: (No Substitutions) Samsung LED HDTV 60"LED HDTV Chief LTM1U Large Fusion Tilt Wall Mount C2G #39710 HDMI Decora Wall Plate 16

Rooms 119, 120, 121, 150, 151, 208, 210, 225, Public Works 304, and Public Works 305 Rooms 119, 120, 121, 150, 151, 208, 210, 225 Public Works 304, and 305 will have a wall mounted 50 display in each room. The built in speakers from the display will be used for room audio. An HDMI cable will be ran from the display and terminated into a wall plate for an input into the display. Vendor is responsible programming and commissioning of all installed equipment. A single gang wall plate will be connected using the HDMI input of the display. Required use of parts listed below for each room: (No Substitutions) Each Room Samsung Pro grade display 50"LED HDTV Chief MTM1U Medium Fusion Tilt Mount C2G #39710 HDMI Wall Plate 17

Room 207 Room 207 will have a wall mounted 50 LED HDTV display in each room. The built-in speakers from the display will be used for room audio. An HDMI cable will run from the display and terminated into a wall plate for an input into the display. A video feed from PC in room 212 will be ran to TV Display for NVR reviewing. Vendor is responsible programming and commissioning of all installed equipment. 1. Single gang wall plate will be connected using the HDMI input of the display. 2. Wall mounted PC from room 212 Required use of parts listed below for each room: (No Substitutions) Each Room Samsung Pro grade display 50"LED HDTV Chief MTM1U Medium Fusion Tilt Mount C2G #39710 HDMI Wall Plate 18

Room 211 Vendors will be responsible for installing a 60 display on the designated wall. This display will have one cable connected via HDMI and terminated to a wall plate for user connected devices. Assumed location will be near the user PC so this monitor can be used as an extended desktop display. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. Displays A Samsung 60 LED HDTV display with Chief mounting hardware Audio The speakers in the TV will be utilized for audio. A single gang wall plate will be connected using the HDMI input of the display. Required use of parts listed below: (No Substitutions) Samsung LED HD TV 60"LED HDTV Chief LTM1U Large Fusion Tilt Wall Mount C2G #39710 HDMI Decora Wall Plate 19

Room 212 Vendors will be responsible for installing a 60 display on the designated wall. This display will have one cable connected via HDMI and terminated to a wall plate for user connected devices. Assumed location will be near the user PC so this monitor can be used as an extended desktop display. A township supplied PC will be wall mounted behind the display for viewing of building NVR. From PC a video signal will be ran to room 207 for NVR viewing. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. Displays A Samsung 60 LED HDTV display with Chief mounting hardware Audio The speakers in the TV will be utilized for audio. 1. Single gang wall plate will be connected using the HDMI input of the display. 2. Wall mounted PC Required use of parts listed below: (No Substitutions) Samsung LED HD TV 60"LED HDTV Chief LTM1U Large Fusion Tilt Wall Mount C2G #39710 HDMI Decora Wall Plate 20

Room Public Works 306 Public Works 306 will have a wall mounted 50 LED HDTV controllable display. The built-in speakers from the display will be used for room audio. The contractor will install a cable cubby into the room s conference table. Out of the cable cubby will be an HDMI that will be used for connectivity to the display. The cable cubby HDMI connection will be transported to the display using an HDMI over twisted pair solution. There will be an Extron MLC 100 Plus touch panel installed in the room for power, input, and volume control on the display. Vendors are responsible for all miscellaneous patch cables. Vendor is responsible programming and commissioning of all installed equipment. All user inputs will be connected in a Cable Cubby at the table. Vendors will be responsible for installing the cubby. A template must be provided prior to the install for the furniture manufacturer to make the table hole. The cubby will have power with USB, data, and HDMI. Required use of parts: (No Substitutions) Extron 60-1469-03 MLC 100 Plus Extron 70-1046-02 Cable Cubby 700 Extron 60-1697-01 AC+USB 224 US Extron 70-100-11 Two RJ-45 Female to Female Barrels Extron 70-1049-80 Cable Cubby 500 CCB & Cable Cubby 700 Routing Template Samsung LED HD TV 50"LED HDTV, with RS232 Chief MTM1U Medium Fusion Micro-Adjustable Tilt Wall Mount Gigabit PoE Injector Wireless Keyboard/Mouse Kramer Kramer TP-580T TP-580R HDMI, Bidirectional RS-232 & IR over HDBaseT Twisted Pair Transmitter HDMI, Bidirectional RS-232 & IR over HDBaseT Twisted Pair Receiver 21