0G A is Siemon s advanced, end-to-end augmented category UTP structured cabling system, designed to meet or exceed all 0GBASE-T performance requirements, including alien crosstalk. Siemon s full channel consists of 0G A MAX outlets, Siemon UTP cable and 0G A MAX-series patch panels as well as 0G A MC patch cords and the innovative high-density BladePatch patch cord. The system is supported by multiple work area faceplates and surface mount options in addition to a full suite of Siemon rack and cable management products. 0 W W W. S I E M O N. C O M
0G A MAX MODULES Part of Siemon s end-to-end cabling solution, MAX modules meet or exceed all augmented category performance requirements for support of the 0GBASE-T application standard. This superior level of performance is achieved via an enhanced circuit board design, optimisation of jack pin geometry, and stringent inspection and quality control procedures. 00 MHz Supports 0GBASE-T Application REVOLUTIONARY PCB TUNING Circuit board is tuned and balanced using our patent-pending Phase-Delay technology to maximise performance to 00 MHz. QUICK INSTALLATION Pyramid wire entry system on S0 blocks separates paired conductors when lacing cables to simplify and reduce installation time. Flexible Installation Install from either front or rear of faceplate Easy Termination Terminates with standard 0 termination tools Quick Identification Icons provided for port identification Backward Compatible With category /class E and category e/class D systems and components Universal Wiring T8A and T8B wiring compatible Protective Doors Minimise exposure to dust and other contaminants (not shown) SUPERIOR PERFORMANCE For superior performance, use 0G A modular cords with 0G A MAX modules. MAX MODULES 0GMX-(XX)................... Angled module, T8A/B, rear strain relief cap and protective colour-matching rubber door 0GMX-F(XX).................. Flat module, T8A/B, rear strain relief cap 0GMX-K(XX).................. Keystone module, T8A/B, rear strain relief cap Use (XX) to specify colour: 0 = black, 0 = white, 0 = red, 0 = grey, 0 = yellow, 0 = blue, 07 = green, 09 = orange, 0 = ivory, = bright white, 80 = light ivory, 8 = alpine white Angled modules include one colour-matching, one red, and one blue icon. Door colour is clear for red, yellow, blue and orange angled modules. Flat modules include one colour-matching, one red, and one blue icon. Add -D for optional colour-matching door. Door colour is white for red, yellow, blue, green, and orange modules. Keystone version is designed for integration with various international mounting products and is not compatible with MAX mounting hardware. Add B to end of part number for bulk project pack of 00 modules (angled and flat modules include icons). 0G MAX Modular Faceplates pages 98-99 W W W. S I E M O N. C O M
0G A MAX PATCH PANELS The MAX patch panel provides a rack mount solution enabling augmented category performance in a reliable and flexible modular solution. Available in - and 8-port configurations, the 0G A patch panel s optimised port spacing ensures alien crosstalk performance. SIMPLE PATCH CORD ROUTING Port spacing eliminates need for additional horizontal cable management, saving valuable rack space. PORT IDENTIFICATION Removable designation labels, included, enable proper circuit identification for each port. Standard Fit Panels can be mounted directly on standard 9 inch rack or cabinet Aesthetics Black anodised finish and rolled edges provide a pleasing appearance Optimised for 0Gb/s Port spacing limits the effects of alien crosstalk Port Identification Bold port numbering enables quick identification of outlets Cable Management Panels feature rigid rack mount rear cable managers for easy routing and bend radius control. Modular Design Ports may be partially populated as needed for cost savings REAR CABLE MANAGEMENT Rear cable management bar included for neatly routing horizontal cables to terminations. MAX PATCH PANELS As part of Siemon s end-to-end 0G A system channel, this panel supports system performance specified by 0GBASE-T standards. U 0GMX-PNL-................ -port MAX panel................. 0GMX-PNL-8................ 8-port MAX panel................. Panels include rear cable manager(s), designation labels, cable ties, and mounting hardware. flat 0G A MAX modules available separately. Note: U =.mm W W W. S I E M O N. C O M
0G A BLADEPATCH MODULAR CORDS Siemon s BladePatch patch cord offers a unique augmented category solution for high-density patching environments. It features an innovative push-pull boot design to control the latch, enabling easy access and removal of the cord in tight-fitting areas. The BladePatch cord is ideal for patching high density blade servers, patch panels, or any equipment with RJ- outlets. UNIVERSAL COMPATIBILITY Fits within any standard RJ- outlet. Push-Pull Boot Activates Latch 00 MHz Supports 0GBASE-T Application REVOLUTIONARY LATCH Simply push the boot forward to latch into the outlet and pull back to release. Revolutionary Design Patented push-pull latch design eliminates need to defeat thumb latch used in standard modular plug designs. Enables easy access and removal in high density patching environments Universal Wiring Compatible with T8A/B wiring schemes Snagless Push-pull design eliminates external thumb latch which can snag and break Low Profile Boot Design Optimises sidestackability of patch cords and facilitates use in equipment with extremely high port density Optimised Bend Radius Patent pending design removes outer jacket layer at plug ends to improve bend radius and flexibility High Performance 0G A cords feature dual jacket construction for excellent alien crosstalk performance HIGH DENSITY The push-pull design enables easy access and removal via the boot in tight-fitting areas. BLADEPATCH MODULAR CORDS Combine the BladePatch with Siemon s new MAX modules, patch panels and cable for a complete augmented category channel solution, meeting or exceeding all 0GBASE-T requirements including alien crosstalk. BPA-(XX)-(XX)................ 0G A BladePatch double ended, -pair UTP stranded modular cord with push-pull latching design, colour matching cord/boot, T8A/B, CMG Use st (XX) to specify cord length: 0 = 0.9m, 0 =.m, 07 =.m, 0 =.m, =.m, 0 =.m Use nd (XX) to specify colour: 0 = black, 0 = white, 0 = red, 0 = grey, 0 = yellow, 0 = blue, 07 = green Add B for bulk project pack of 00 modular cords. W W W. S I E M O N. C O M
0G A MC MODULAR CORDS Siemon takes patch cord performance to the next level with our 0G A MC modular patch cords. These next generation cords meet or exceed all augmented category component requirements and provide channel performance to 00 MHz. 00 MHz Supports 0GBASE-T Application METALLIC ISOLATOR Patented metallic isolator shields pairs inside plug for optimum NEXT performance. EXCELLENT BEND RELIEF 7mm boot ensures excellent bend relief, critical for augmented category performance. Universal Wiring Compatible with T8A/B wiring schemes Latch Guard Boots feature a latch guard to protect plug from snagging when pulling through pathways or cable managers High Performance 0G A cords feature dual jacket construction for excellent alien crosstalk performance Superior Quality Internal stranded cordage isolator provides extended flex life and maintains ideal pair geometry. 0 degree crimp provides excellent plugto-cable strain relief without causing pair deformation Optimised Bend Radius Patent pending design removes outer jacket layer at plug ends to improve bend radius and flexibility SUPERIOR PERFORMANCE 00% transmission testing ensures augmented category modular cord specifications and guarantees optimum field performance. MC MODULAR CORDS A variety of plug and cable enhancements contribute to the cords performance including a patented cross-pair isolator, extended frequency cable and an innovative 0 crimp which provides excellent plug-to-cable strain relief without causing pair deformation. Combine the 0G A MC modular cord with Siemon s MAX modules, patch panels and cable for a complete channel solution. MCA-(XX)-(XX)............... 0G A MC, double-ended, -pair UTP stranded modular cord, colour matching jacket/boot, T8A/B, CMG Use st (XX) to specify cord length: 0 = 0.9m, 0 =.m, 07 =.m 0 =.m, =.m, 0 =.m Use nd (XX) to specify colour: 0 = black, 0 = white, 0 = red, 0 = grey, 0 = yellow, 0 = blue, 07 = green Add B for bulk project pack of 00 modular cords. W W W. S I E M O N. C O M
0G A S0 CONNECTION SYSTEM The Siemon S0 offers the best connecting block performance in the telecommunications industry. Its NEXT performance is so exceptional that it is essentially transparent when used as a consolidation point in a standard or augmented category channel.* INTERNAL CROSSTALK BARRIERS Provide superior NEXT performance ( db NEXT margin over category specifications) via 0 pair isolation. PYRAMID WIRE ENTRY SYSTEM Separates paired conductors when lacing cables to simplify and reduce installation time. Coloured Labels Designation strip with interchangeable coloured labels can be mounted between each row of connecting blocks Stand-off Legs Patented stand-off legs may be detached from the block before, during, or after installation on -pair version Superior Design Cable entering through access openings in base is concealed by designation labels * See warranty information for allowable 0G A configurations. Compatibility Utilises same wiring base footprint as standard S0 products to be fully compatible with existing S0 mounting and cable management solutions Easy Termination Utilises same termination practices as existing S0 product and is compatible with all single-position S0 termination tools CABLE ACCESS OPENINGS Allow cables to be routed through the rear of the block directly to the point of termination. S0 FIELD TERMINATION KITS Complete S0 installation kits include S0 wiring blocks with detachable legs*, S0 connecting blocks, and label holders with white designation labels. S0AB-FT................. -pair, S0 field termination kit height: 9.mm, width: 7mm depth: 8.8mm S0AB-8FT................ 8-pair, S0 field termination kit height: 8.9mm, width: 7mm, depth: 8.8mm S0AB-9FT................ 9-pair, S0 field termination kit height: 7mm, width: 7mm, depth: 8.8mm *Legs detachable on -pair version only. W W W. S I E M O N. C O M
0G A S0 FIELD TERMINATED 9 INCH PANELS S0 panels allow wiring blocks to be mounted directly to a 9 inch rack or cabinet. Each panel includes adequate connecting blocks to complete each -pair termination strip on the 0 block as well as label holders with white designation labels. Patented openings between rows allow horizontal cables to be routed from behind the panel and enter the block from the rear, helping to maintain cable geometry up to the point of termination. U S0DB-RFT................ -pair, 9 inch S0 field termination kit.................. S0DB-8RFT............... 8-pair, 9 inch S0 field termination kit.................. S0DB-9RFT............... 9-pair, 9 inch S0 field termination kit.................. \ S0 TOWER FIELD TERMINATION KITS The S0 Tower field termination kits provide a modular, high density, cross-connect, and cable management system. Each kit includes adequate connecting blocks to fully populate tower as well as label holders with white designation labels. The Towers and vertical cable managers are completely modular and can be vertically stacked to accommodate a higher capacity in a single column. The modular design of the large-scale vertical cable managers allow a technician to easily install a high-density cross-connect system without spending valuable time laying out a termination field. S0MB-9FT................ 9-pair, S0 Tower field termination kit height: 0mm, width: mm, depth: mm S0MB-FT -pair, S0 Tower field termination kit height: mm, width: mm, depth: mm S0MB-0FT................ 0-pair, S0 Tower field termination kit height: 7mm, width: mm, depth: mm W W W. S I E M O N. C O M
0G A TRUNKING CABLE ASSEMBLIES Siemon s Category A UTP trunking cable assemblies provide an easily installed and cost effective alternative to individual field-terminated channels. Combining factory terminated and tested MAX modules with Siemon s cable in a high-performance modular cable assembly, trunking cable assemblies are designed to simplify the installation of 0Gb/s systems in data centres and other high-density, high-performance environments. DATA CENTRES Ideal for Data Centre installations where raised floor and ladder rack environments accommodate easy installations. TRIDENT CUT Typical installation utilising Trident cut ensures each cable is terminated at the proper length. Proper Orientation Each leg is cut and labelled for proper module orientation Category A UTP Cable Utilises high quality Siemon cable Factory Terminated and Tested Utilises flat 0G A UTP MAX modules, factory terminated and tested for high performance Identification Each cable assembly is coded with a unique identification number for administrative purposes Breakout Kit Unique breakout kit creates optimal cable orientation and limits cable crossing PROTECTIVE PACKAGING Each assembly is packaged individually to protect factory terminations. TRUNKING CABLE ASSEMBLIES Leg Trunking Cable Assemblies: TDRDE-AA(XXX)(X).........., riser rated (CMR), double ended flat black MAX modules, blue jacket, 00MHz TDPDE-AA(XXX)(X).........., plenum rated (CMP), double ended flat black MAX modules, blue jacket, 00MHz TDLD8E-AA(XXX)(X).........., LS0H rated (IEC 0-), double ended flat black MAX modules, violet jacket, 00MHz TRIDENT/CENTRE CUT Description: Supports left, right or centre exit. Use (XXX) to specify length: 00-m in increments of metre 009-0 ft. in increments of feet Use (X) unit: M = metres, F = feet Other lengths available upon request. Note: These products are made to order. Call for lead time and part number availability in your region. W W W. S I E M O N. C O M 7
0G A -PAIR SOLID ROUND CABLE US COMPLIANCE ISO/IEC 80:00 (Category ) ISO/IEC 80:00, Amendment (draft) TIA/EIA-8-B.-0 (draft) TIA/EIA-8-B.- IEC -:00 (Category ) UL CMR and CSA FT UL CMP and CSA FT CABLE CONSTRUCTION UTP 0.7mm ( AWG) solid bare copper 8.9mm max jacket diameter Round jacket Spiral isolation member 9CP-A-(XX)-RA............ Plenum (CMP, CSA FT) 0m Reel 9CR-A-(XX)-RA............ Riser (CMR, CSA FT) 0m Reel Use (XX) to specify jacket colour: 0 = white, 0 = red, 0 = grey, 0 = yellow, 0 = blue, 07 = green ELECTRICAL SPECIFICATIONS DC Resistance <9.8 Ω/00m DC Resistance Unbalance % Mutual Capacitance Capacitance Unbalance. nf/00m <0 pf/00m Characteristic Impedance - 00 MHz: 00 ± % (ohms) 00-70 MHz: 00 ± % NVP CMP 7% CMR 8% LCL PSANEXT PSAACR-F Delay Skew 0-0log(f /00)dB.-log(f /00)dB 8.-0log(f /00)dB ns PHYSICAL PROPERTIES CMP CMR Pulling Tension (max) 0N ( lbf) 0N ( lbf) Bend Radius (min).mm.mm Installation Temperature 0 to 0 C - to 0 C Storage Temperature -0 to 7 C - to 7 C Operating Temperature -0 to 0 C - to 0 C TRANSMISSION PERFORMANCE GUARANTEED WORST CASE SIEMON TYPICAL Frequency Insertion Loss NEXT PS NEXT ACR PSACR ACR-F PS ACR-F Return Loss Propagation (MHz) (db) (db) (db) (db) (db) (db) (db) (db) Delay (ns).0..8 7. 9.0 7. 9.0 7. 9. 70. 90. 7.8 9.0.8 8.0 0.0 9.0 70 0.0.8.. 89.0. 8.0. 8.7 9. 79.7.7 80.0.7 7.0.0.0 0.0.9. 9. 8.0 7. 77.0. 77.8. 7.8 7.8 7.0.8.0.0.0.0 7..7. 80.0. 7.0 8.8 7..8 7..7 8.0 0.7.0.0.0 0.0 8. 7..8 79.0.8 7.0. 7....7 8.0 8.7 9.0.0.0. 0. 9..9 7.0 9.9 70.0.. 9. 0. 7.9.0.9.0..0 0 0..0.7 7. 7.0..0. 7. 0...8.0 8.8 9.0..0 9 09 00.0 9. 7.8. 8.0..0. 0... 7.8.0.8.0 0..0 8 07 00.0 7..8 9.8.0 7.8 8.0. 8. 0...7.0 8.7 9.0 8.0.0 7 0 0.0. 9. 8..0..0 7..8..8 9.8.0.8 7.0 7..0 0 00.0.. 7..0..0.9 9. 0.9. 8..0..0.8 9.0 0 0.0 7..8. 0.0..0 -.. -. 0..9.0.9.0. 8.0 0 00.0 0. 7.9. 9.0..0 -.8. -.8..7 0.0.7.0.9 7.0 0 00.0...8 7.0.8.0 -..9 -. 8.9.8 9.0 0.8.0..0 0.0*..9..0 0. 0.0-8.8 8. -0.8..8.0 8.8 9.0..0 0 70.0*.7 9.0..0 9. 9.0 -..0-7. 0.0 0..0 7. 7.0.0.0 0 *Performance for frequencies beyond TIA and ISO requirements are for information only. All performance based on 00 metres. Cable Preparation Tool page 8 W W W. S I E M O N. C O M
0G A -PAIR SOLID ROUND CABLE INTERNATIONAL COMPLIANCE ISO/IEC 80:00 (Category ) ISO/IEC 80: 000 Amendment (draft) TIA/EIA-8-B.-0 (draft) TIA/EIA-8-B.- IEC -:00 (Category ) LS0H: IEC 0-, IEC 07 and IEC 0 9CL-A...................... LS0H (IEC 0-) Violet Jacket, 0m Reel 9CL-A-CR................. LS0H (IEC 0-) Violet Jacket, 00m Reel 9CL-A-KR................. LS0H (IEC 0-) Violet Jacket, 000m Reel CABLE CONSTRUCTION UTP 0.7mm ( AWG) solid bare copper 8.mm max jacket diameter Round jacket Centre isolation member ELECTRICAL SPECIFICATIONS DC Resistance <9.8 Ω/00m DC Resistance Unbalance % Mutual Capacitance Capacitance Unbalance. nf/00m <0 pf/00m Characteristic Impedance - 0 MHz: 00 ± % (ohms) 00-70 MHz: 00 ± % NVP 9% LCL PSANEXT PSAACR-F Delay Skew 0-0log (f /00)dB.-log(f /00)dB 8.-0log(f /00)dB ns PHYSICAL PROPERTIES LS0H Pulling Tension (max) 0N ( lbf) Bend Radius (min).mm Installation Temperature 0 to 0 C Storage Temperature -0 to 7 C Operating Temperature -0 to 0 C TRANSMISSION PERFORMANCE TIA/EIA & ISO/IEC SIEMON TYPICAL Frequency Insertion Loss NEXT PS NEXT ACR PSACR ACR-F PS ACR-F Return Loss Propagation (MHz) (db) (db) (db) (db) (db) (db) (db) (db) Delay (ns).0..8 7. 9.0 7. 9.0 7. 9. 70. 90. 7.8 9.0.8 8.0 0.0 9.0 70 0.0.8.. 89.0. 8.0. 8.7 9. 79.7.7 80.0.7 7.0.0.0 0.0.9. 9. 8.0 7. 77.0. 77.8. 7.8 7.8 7.0.8.0.0.0.0 7..7. 80.0. 7.0 8.8 7..8 7..7 8.0 0.7.0.0.0 0.0 8. 7..8 79.0.8 7.0. 7....7 8.0 8.7 9.0.0.0. 0. 9..9 7.0 9.9 70.0.. 9. 0. 7.9.0.9.0..0 0 0..0.7 7. 7.0..0. 7. 0...8.0 8.8 9.0..0 9 09 00.0 9. 7.8. 8.0..0. 0... 7.8.0.8.0 0..0 8 07 00.0 7..8 9.8.0 7.8 8.0. 8. 0...7.0 8.7 9.0 8.0.0 7 0 0.0. 9. 8..0..0 7..8..8 9.8.0.8 7.0 7..0 0 00.0.. 7..0..0.9 9. 0.9. 8..0..0.8 9.0 0 0.0 7..8. 0.0..0 -.. -. 0..9.0.9.0. 8.0 0 00.0 0. 7.9. 9.0..0 -.8. -.8..7 0.0.7.0.9 7.0 0 00.0...8 7.0.8.0 -..9 -. 8.9.8 9.0 0.8.0..0 0.0*..9..0 0. 0.0-8.8 8. -0.8..8.0 8.8 9.0..0 0 70.0*.7 9.0..0 9. 9.0 -..0-7. 0.0 0..0 7. 7.0.0.0 0 *Performance for frequencies beyond TIA and ISO requirements are for information only. All performance based on 00 metres. Cable Preparation Tool page W W W. S I E M O N. C O M 9