Optical Broadband Platform NEW: Passive optical components

Optical Broadband Platform NEW: Passive optical components Antennen Electronic

Optical Broadband Platform Optical broadband platform for up to 16 modules Equipped with 2 redundant power supply and fan units Wide selection of optical transmitters, amplifiers and return path receivers All optical and electrical connections are located on the rear panel. Test sockets are on the front panel Can be integrated in every HMS-conform monitoring system Pluggable control panel with LC display, LEDs and input keys Tuning and management also via web browser RS 485 remote monitoring and control interface Several optical broadband platforms can be managed using just one controller module Automatic redundant operation of adjacent modules High reliability due to dust-proof designed modules and large cooling ribs Models available for mains voltage (100...240 V AC ) and direct voltage (36...72 V DC ) Design: 19 racking, 4 height units (HU) Kathrein's KOBRA system offers a comprehensive broadband platform meeting all the requirements of optical transmission. A wide range of optical transmitters, amplifiers and return path receivers is complemented by individual units in 19 design. The foundation is based on the 19 broadband platform KBP 4000R, into which a total of 16 modules can be inserted. It is already equipped with two redundant power supply and fan units ensuring reliable operation. The product package additionally includes a pluggable control panel with LC display, status LEDs and input keys. A power bus system in the rear section of the platform enables direct module connection to the 24 V DC supply voltage, to the RS 485 remote supervision and control interface as well as to control panel management. The broadband platform is designed as a 4 HU module carrier and can also be adapted to ETSI cabinets. For use in hubs, for example, the remotely fed broadband platform 48 V DC variant (KBP 4048R) can also be used. Extensive management and monitoring facilities allow flexible and reliable operation in any net configuration. The provided pluggable control panel enables all required settings to be made on inserted devices. The net element controller module Ethernet (NCM 10) plays the leading role in this function. This unit establishes the connection between the control panel and all plugged-in modules via the RS 485 bus. The NCM 10 can thereby control up to three full KBP 4000R or 4048R broadband platforms. On the other hand, it converts the RS 485 data to SNMP/Ethernet and web browser/ Ethernet protocol. Thus, all settings and queries can be carried out via PC with a web browser. In addition, it is possible to integrate the broadband platform in any HMS-compatible monitoring system such as the KOM system from Kathrein. Together with the Kathrein optical compact receivers, the KOBRA can be used to set up an optical distribution system that meets each and every requirement. Modular design and a broad product programme make it possible to design anything in a costeffective fashion from simple optical feeds to classical HFC structures and video distribution in FTTH networks. Kathrein are continually enhancing their products and expanding their product range. Additional product variants are available upon request. 2 3

Functional and reliable - the optical broadband platform in detail The optical broadband platform KOBRA is designed with a sophisticated operation and management concept. The central element is the net element controller Ethernet "NCM 10. This module provides the interface to the rear RS 485 bus to which all platform modules are connected. In addition, it establishes the connection to external management systems, e.g. via web browser, or monitoring systems, such as HMS monitoring systems. Power supply Ethernet NCM 10 +24 VDC µp LC Display I/0 RS485 Input Keys 2 Power supply 3 Gerät 16 Two redundant power supply units, each equipped with double fan units, ensure high reliability. If service is required, the power supply units can even be exchanged under operational conditions (hot-pluggable). Ultimately, it enables local setting of all parameters through the control panel with display and input keys. Decentralized data storage in each individual module allows independent operation (without the controller module) after start-up. Ample cooling ribs guarantee long endurance of all active components. An additional advantage is the dust-proof design of all components. Slim modules, some with dual functions (e.g. return path receiver), ensure high functional density. Minimal space requirement increases cost-effectiveness and makes later upgrading easier. Despite their high output power, the optical amplifiers only require two or three slots. All test sockets are located on the front panel. This guarantees easy access for tests or measurements. The cooling air only flows along the cooling ribs and not through the modules themselves. Disturbances due to dust and dirt are therefore practically ruled out. The optical and RF interfaces are located on the rear panel of the platform, simplifying cabling in 19 racks. 4 5

19" Broadband platform for optical modules Net element controller module Ethernet KBP 4000R 25010022 KBP 4048R 25010021 Up to 16 modules can be inserted into the broadband platform Fitted with 2 redundant power supply and cooling fan units Power supplies can be exchanged under operation Plug-in controller with LC display, status LEDs and input keys Bus for: - 24 V DC module power supply - RS 485 remote monitoring and control interface - Controller management Models available for 100... 240 V AC and 48/60 V DC powering Automatic recognition of inserted modules Design: 19 racking, 4 height units (HU) Can be adapted to ETSI defined cabinets Note: The net element controller module Ethernet NCM 10 is required if modules are to be tuned to other settings and for monitoring purposes NCM 10 26210079 Zum For management Management and und monitoring Überwachung of active aktiver modules in the in 19 der broadband 19 -Breitband- platform Plattform KBP 40xxKBP 40xx Umwandlung Conversion of von RS RS 485485-Daten data in to SNMP/Ethernet- and und Webbrowser/ Ethernet-Protokoll protocol Schnittstelle Interface to displays zu Displays and und input keys on Eingabetasten the front panel der Fronteinheit Automatische Automatic recognition Erkennung of aller modules an den RS connected 485-Bus to angeschlossenen the RS 485 bus Schnittstelle Ethernet interface Ethernet 10/100 10/100 Mbit/s Mbit/s for für SNMPv1 und and Webserver Flash Microcontroller-Technologie micro-controller technology for für schnelle rapid and und simple leichte software Software-Updates updates via über Ethernet die Ethernet-Schnittstelle interface LEDs zur for status Statusanzeige display Niedrige Low power Leistungsaufnahme consumption Hinweis: Note: Ein Up to NCM three 10 broadband kann bis zu platforms drei Breitband- Plattformen KBP 40xxR KBP can be 40xxR managed verwalten and und überwachen monitored by one NCM 10 module Type KBP 4000R KBP 4048R Order no. 25010022 25010021 Input voltage V AC: 100-240 DC: 36-72 Power consumption max. W < 240 < 240 Power consumption of inserted modules max. W < 192 < 192 Dimensions (W x H x D) mm 483 x 102 x 476 483 x 102 x 476 LAN / WAN TCP/IP RJ45-Cable Ethernet NCM 10 Kobra Broadband Platform #1 Kobra Broadband Platform #2 Kobra Broadband Platform #3 µp LC Display RS 485 RS 485 I/O RS 485 17 33 Input Keys 2 18 34 3 19 35 16 32 48 RJ45 Cable RJ45 Cable Weight kg 12 12 Type NCM 10 Order no. 26210079 Power consumption W 2.5 6 7

Directly modulated broadcast transmitters, 1310 nm, extremely linear 1303X2-E 24610353 1305X2-E 24610354 1308X2-E 24610355 1311X2-E 24610356 1313X2-E 24610357 1314X2-E 24610358 Opto-electrical conversion of the forward path signal Extremely linear, low-noise laser with pre-distortion technology Optical output power between 3 and 14 dbm Adjustable optical output level, 0 to -3 db (relative) Active narrowcast input (NC) with high decoupling to the broadcast signal (BC) Electronic tuning elements for attenuation, slope, output level, Optical Modulation Index (OMI) etc. Automatic load control for constant OMI RS 485 interface Optical interface: E-2000, 0.1 db-type (other connector types on request) Test socket for input signal Test socket for RF signal in front of the laser diode Type 1303X2-E 1305X2-E 1308X2-E 1311X2-E 1313X2-E 1314X2-E Order no. 24610353 24610354 24610355 24610356 24610357 24610358 Nominal output level optical dbm 3 5 8 11 13 14 Wave length nm 1310 Optical output level range (relative) db 0 to -3 Optical return loss db > 45 RF frequency range MHz 5-1000 Nominal input level (5 % OMI, Broadcast) Nominal input level (5 % OMI, Narrowcast) Level range (BC), in relation to nominal input level, electronically settable Slope range (BC), electronically settable Level range (NC), electronically settable dbµv 80 dbµv 80 dbµv 73 97 db -3... +16 dbµv 80 92 Decoupling between BC and NC input db > 50 Return loss at 47 MHz db 20-1.5/oct., > 15 Return loss 5-65 MHz db > 18 Impedance Ω 75 Power consumption (operation) W 12 Power consumption (stand-by) W 4 CSO (CENELEC 42) dbc 68 CTB (CENELEC 42) dbc 69 NEW: Active narrowcast input 8 9

Optical return path receivers, twin Optical return path receiver, quad ORM 22E 24710026 ORM 40E 24710018 Opto-electrical conversion of return path signals Two receivers, with individual shut-down Two separate outputs with test sockets Redundant operation possible Optical power monitoring on all inputs Pilot-controlled Wide optical input power range RS 485 Interface Stand-by mode for unused receiver to reduce power consumption Very low power consumption Optical interfaces: E-2000, 0.1 db-type (other connectors on request) TP #1 ICS #1 IN #1 OUT #1 µp RS485 Opto-electrical conversion of return path signals Four receivers, with individual shut-down Four separate outputs, each switchable to the test port Redundant operation possible Optical power monitoring on all inputs Pilot-controlled and optical power controlled AGC as well Wide optical input power range RS 485 Interface for supervision and control Line code evaluation Stand-by mode for unused receiver to reduce the power consumption Very low power consumption Optical interfaces: E-2000, 0.1 db-type (other connectors on request) Requires two slots in KOBRA KBP 40xx-R subrack LEDs LON µp µc PSK AGC Demod (opt. input power RS485 or pilot contr olled ) Optical input -22... +2dBm Optical input -22... +2dBm 0...10dB 0...24dB 0...10dB 0...24dB 20 db test point RF output >85dBµV 20 db test point RF output >85dBµV Optical input RF output -22... +2dBm 0...10dB 0...24dB >85dBµV ICS #2 IN #2 OUT #2 Optical input 20 db test point RF output OR265-nn TP #2-22... +2dBm 0...10dB 0...24dB 20 db test point >85dBµV Type ORM 22E Type ORM 40E 10 Order no. 24710026 Optical interfaces E-2000 Optical wave length nm 1280-1610 Optical input level range dbm -16 to +2 Optical return loss db > 40 RF frequency range MHz 5-160 RF output level at OMI = 5 % dbµv 90 Frequency response db ± 0.75 Return loss db > 19 Pilot control range db 36 Optical modulation index pilot % 5 Test sockets db 20 Impedance Ω 75 Power consumption, normal operation/stand-by W 3.5/1.5 Order no. 24710018 Optical interface E-2000 Optical wave length nm 1280-1610 Detector responsivity A/W 0.8 Receiver noise current at -16 dbm pa/ Hz 2.5 Optical input level range dbm -16 to +2 Optical return loss db > 45 RF frequency range MHz 5-200 RF output level at OMI = 5 % dbµv 75 Frequency response db ± 0.75 Return loss at 47 MHz db > 20 RF output connector F-type Test port connector F-type Pilot control range db 26 Frequency of ALC pilot tone khz 590 640 Optical modulation index pilot % 5 Test sockets db 20 Impedance Ω 75 Power consumption normal operation (all 4 receivers active)/stand-by W 8/1.5 CINR at -11 dbm (4 QAM carrier with 2 MHz bandwidth, 10 % OMI) db 50 11

Optical amplifiers Broadband amplifier, 5-1000 MHz 113S-E 24910028 213S-E 24910029 413S-E 24910030 116S-E 24910031 216S-E 24910032 416S-E 24910033 Amplifies optical signals in the 1550 nm range Optical output power 13 or 16.5 dbm respectively; 1-4 outputs, type dependant Monitoring of optical input and output levels and pump laser current 1 or 2 pump lasers, type dependant Automatic switch-off in case of low input level Low noise figure Stand-by mode for low power consumption Requires two or three slots in the optical broadband platform KBP 40xxR Optical interfaces: E-2000, 0.1 db-type (other connectors on request) TVO 1024 25110033 Broadband amplifier for universal use in forward and return paths For use in the optical broadband platform KOBRA Automatic load control (can be switched off) Frequency range 5-1000 MHz Gain 0... 24 db, electronically settable Slope range 0... 16 db, electronically settable Main input for broadcast signals and secondary input for narrowcast signals Test socket for output signal Stand-by mode for low power consumption RS 485 interface IN IN (coupled) CA1024 ATT, EQ µp OUT TP RS485 Type TVO 1024 Order no. 25110033 Frequency range MHz 5-1000 Type 113S-E 213S-E 413S-E 116S-E 216S-E 416S-E Order no. 24910028 24910029 24910030 24910031 24910032 24910033 Optical wave length nm 1540-1560 Optical interfaces E-2000 Optical return loss db 50 Optical input level dbm -4 +10 Noise figure (at 0 dbm) db < 4.8 Optical output level per output dbm 13 13 13 16 16 16 Optical output power tolerance (1551-1556/1548-1560 nm) db ± 0.5/0.8 No. of outputs 1 2 4 1 2 4 No. of pump lasers 1 1 2 1 2 2 Power consumption, operation W 12 12 24 12 24 24 Power consumption, stand-by W 6 6 10 6 10 10 No. of required slots in KBP 40xxR 2 2 2 2 2 3 Gain, electronically settable db 0 to 24 Slope electronically settable db 0 to 16 Frequency response (7-870 MHz) db ± 0.8 Frequency response (5-1000 MHz) db ± 1.5 Input level narrowcast input 1), relative to main input db + 14 Max. output level 2), CSO > 60 db, CTB > 60 db dbµv 106 Return loss 5-65 MHz db > 18 Return loss 47-1000 MHz db 18-1/oct., > 15 Noise figure 5-870 MHz db 6.5 Noise figure 870-1000 MHz db 7.5 Impedance Ω 75 Power consumption, normal operation W 9 Power consumption, stand-by mode W 1 1) 14 db directional coupler 2) CENELEC channel plan, 42 channels, flat 12 13

Externally modulated transmitters (19" design), 1550 nm Optical amplifiers (19" design) ESA 1085XA-E 24610252 ESA 1085XA-E 24610140 Opto-electrical conversion of forward path signals Designed for operation with optical amplifiers (EDFAs/YEDFA) Excellent parameters enable design of optical distribution systems over 100 km in length Very low-noise, narrow-band DFB laser Optical modulator with 2 optical outputs Automatic RF gain control: CW carrier, video or manual Settable SBS threshold up to 19 dbm Service interface: HTTP/SNMP Ethernet LC display and LEDs on front panel: Optical wavelength 1558.98 nm (ITU channel 23) Additional wavelengths and optical output levels on request Optical interfaces E-2000, 0.1 db-type (other connectors on request) Test socket -20 db Two power supply modules, pluggable/exchangeable during operation Design: 19 racking, 1 height unit, depth 600 mm Power supply 230 V AC or 48 V DC /60 DC, type dependant OBV 1616 24910037 OBV 3216 24910036 OBV 820 24910035 OBV 1620 24910034 Amplifies optical signals in the 1550 nm range Optical output power 16.5 or 20 dbm, 8-32 outputs, type dependant Monitors optical input and output levels as well as pump laser current ErYb-doped optical amplifier Low noise figure LC display, LEDs and input keys on front panel RS 485 interface for management Ideal for FttH or HFC applications Optical interfaces: LC/APC Design: 19 racking, 1 height unit (HU) Two power supply modules, pluggable/exchangeable during operation 14 Type ESA 1085XA-E ESA 1085XA-E Order no. 24610252 24610140 Optical interfaces E-2000 Optical wave length nm 1558.98 Optical output level dbm 2 x 8.5 Relative intensity noise (RIN) dbc/hz -160 Input level, per TV channel, nominal dbµv 80 AGC dynamic range db +3... -6 Return loss at 47 MHz db 20-1.5/ oct., > 15 Frequency range MHz 47-1000 Frequency response, 47-862 MHz db ± 0.75 Test socket db -20 ± 1 RF interfaces F-type connector (female) Voltage supply V 100... 240 AC ± 36... ± 72 DC Power consumption W 60 Type OBV 1616 OBV 3216 OBV 820 OBV 1620 Order no. 24910037 24910036 24910035 24910034 Optical wave length nm 1545-1565 Optical return loss db 45 Optical input level dbm -5 +10 Noise figure (at 0 dbm) db < 5.5 Optical output power per output dbm 16.5 16.5 20 20 Optical decoupling, input db 35 Optical decoupling, output db 35 No. of outputs W 16 32 8 16 Power consumption, max. W 45 45 40 45 Supply voltage V AC 100 240 15

FTTx CATV splitter 19", 1 HU FTTx CATV splitter WDM 19", 1 HU BOS 264LC 25010044 BOS 432LC 25010045 19 racking (1 HU) Suitable for up to 2 x 64 fibres Includes two independent optical 1:64 splitters or four independent 1:32 splitters Combined input and outputs with LC/APC connectors ITU G.694.2 compliant Broadband PLC splitter Integrated fibre tray BOW 064LC 25010041 BOW 232LC 25010046 19 racking (1 HU) to feed in CATV signals with 1550 nm in GBE-FTTx and PON-FTTx networks Suitable for up to 64 fibres Single-fibre solution for Triple Play systems with CATV overlay Data inputs with LC or LC/APC connectors CATV input and combined outputs with LC/APC connectors ITU G.694.2 compliant Type BOS 264LC BOS 432LC Order no. 25010044 25010045 Configuration 2 x 1:64 4 x 1:32 Wave length range nm 1260... 1625 1260... 1625 Max. insertion loss per splitter ¹) db 21.1 18.0 Uniformity db < 1.0 < 1.0 Polarisation dependent loss db 0.4 0.3 Typ. isolation (directivity) db 55 55 Min. return loss db 55 55 Temperature range (operational) C -40... +80-40... +80 Temperature range (storage) C -40... +80-40... +80 Relative humidity (non-condensing) % 90 90 Max. optical output mw < 300 < 300 Dimensions (W x H x D) mm 482 x 45 x 196 482 x 45 x 196 Fibre type (Core diameter/sheathing diameter/ outer diameter) µm 9/125/250 9/125/250 Type of optical connection LC/APC LC/APC Type BOW 064LC BOW 232LC Order no. 25010041 25010046 Configuration 1 x 1:64 with WDM 2 x 1:32 with WDM Wave length data downstream nm 1490 1490 Wave length data upstream nm 1310 1310 Wave length CATV downstream nm 1550... 1560 1550... 1560 Typ. insertion loss data ¹) db 1.0 1.0 Max. insertion loss CATV ¹) db 21.4 18.4 Typ. isolation data upstream to CATV db 55 55 Min. return loss db 55 55 Temperature range (operational) C -40... +80-40... +80 Temperature range (storage) C -40... +80-40... +80 Relative humidity (non-condensing) % 90 90 Max. optical output mw < 300 < 300 Dimensions (W x H x D) mm 482 x 45 x 196 482 x 45 x 196 Fibre type (Core diameter/sheathing diameter/ ¹) Einschließlich opt. Steckverbindungen outer diameter) µm 9/125/250 9/125/250 ¹) Including opt. connectors ¹) Including opt. connectors 16 17

Optical splitters Optical taps BOV 002 24810029 BOV 003 24810042 BOV 004 24810039 BOV 008 24810054 BOV 002-CWDM 24810162 BOV 003-CWDM 24810184 BOV 004-CWDM 24810160 Optical splitters for universal application Low insertion loss Optimised for 1310 and 1550 nm wave lengths Optical connectors: E-2000 (other connector types available on request) High reliability Ultra-compact design, including pigtails BOC 003 24810055 BOC 004 24810056 BOC 005 24810057 BOC 006 24810058 BOC 007 24810059 BOC 008 24810060 BOC 009 24810061 BOC 010 24810062 BOC 012 24810063 BOC 014 24810064 Optical splitters for universal application Low insertion loss Optimised for 1310 and 1550 nm wave lengths Optical connectors: E-2000 (other connector types available on request) Ultra-compact design, including pigtails Type BOV 002 BOV 003 BOV 004 BOV 008 BOV 002- CWDM BOV 003- CWDM BOV 004- CWDM Order no. 24810029 24810042 24810039 24810054 24810162 24810184 24810160 Optical wave length nm 1310 and 1550 1468.5-1617.5 Splitting ratio 1:2 1:2 1:2 1:8 1:2 1:2 1:2 Typ. insertion loss ¹) db 3.2 4.9 6.3 9.5 3.3 5.6 7.4 Max. insertion loss ¹) db 3.6 5.5 7.0 10.6 3.6 5.9 7.7 Uniformity db 0.7 1.1 1.4 2.1 0.7 1.1 1.4 Optical isolation, outputs db 50 ¹ ) Without connector Type BOC 003 BOC 004 BOC 005 BOC 006 BOC 007 BOC 008 BOC 009 BOC 010 BOC 012 BOC 014 Order no. 24810055 24810056 24810057 24810058 24810059 24810060 24810061 24810062 24810063 24810064 Optical wave length nm 1310 und 1550 Typ. tap loss ¹ ) db 3.2 4 5 6 7 8 9 10 12 14 Tap loss tolerance db +/- 0.4 +/- 0.5 +/- 0.6 +/- 0.7 +/- 0.7 +/- 0.8 +/- 0.9 +/- 0.9 +/- 1.3 +/- 1.5 Typ. through loss ¹ ) db 3.2 2.6 1.9 1.5 1.2 0.9 0.8 0.6 0.5 0.4 Through loss tolerance Optical isolation, outputs db +/- 0.4 +/- 0.3 db 50 18 19

Optical patch cables/optical couplers OFC 050/E yellow 24810152 OFC 150/E yellow 24810154 OFC 300/E yellow 24810157 OFC 050/E red 24810151 OFC 150/E red 24810155 OFC 300/E red 24810156 OFC 300/SC 24810104 OFC 300/LC 24810126 OFC 300/LC-E 24810174 Optical patch cables for universal application 2.5 mm patch cord Type OFC 050/E yellow OFC 150/E yellow OFC 300/E yellow OFC 050/E red OFC 150/E red OFC 300/E red OFC 300/ SC OFC 300/ LC OFC 300/ LC-E Order no. 24818152 24818154 24818157 24810151 24810155 24810156 24810104 24810126 24810174 Length cm 50 150 300 50 150 300 300 300 300 Diameter of patch cord mm 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 Opt. attenuation of connectors db 0.1 0.1 0.1 0.1 0.1 0.1 0.3 0.3 0.3 OKU 01/SC 24810031 OKU 01/SC-E 24810099 OKU 01/E 24810100 Optical couplers for universal application Available types: - OKU 01/SC: SC/APC both ends - OKU 01/SC-E: Optical connection adapter SC/APC to E-2000 - OKU 01/E: E-2000 both ends The products described must only be installed by qualified specialists. Please consult the provided instruction manuals for safety instructions that are to be considered during use. 99811337/1/0509/JH/Pf Subject to modification. Technical data represent typical values. Internet: www.kathrein.de E-Mail: catv@kathrein.de KATHREIN-Werke KG Phone +49 (0)8031 184-0 Fax +49 (0)8031 184-385 Anton-Kathrein-Str. 1-3 P. O. Box 10 04 44 83004 Rosenheim GERMANY Antennen Electronic