TFT15, 17, 19 Manual_Layout 2 01/03/2013 15:35 Page 1 TFT LCD monitor USER MANUAL TFT-15 TFT-17 TFT-19
TFT15, 17, 19 Manual_Layout 2 01/03/2013 15:35 Page 2 2
TFT15, 17, 19 Manual_Layout 2 01/03/2013 15:36 Page 3 Contents Setup..................................................................... 4 Functions................................................................. 4 Input Menu............................................................... 5 Video Mode Menu......................................................... 6 VGA Mode Menu........................................................... 7 Troubleshooting........................................................... 7 Technical Specifications................................................... 8 Important Allow enough space between the monitor and the wall to allow ventilation. Avoid excessively warm locations to prevent possible damage to the cabinet or premature component failure. This monitor operates on a AC supply provided by the mains voltage of 90-260V. Do not install the monitor in a location near heat sources, air ducts, direct sunlight, or in a confined area. Please do not tamper with any components inside the monitor, or make any other adjustments not mentioned in this manual. When cleaning the monitor it is advised to use a soft dry cloth. During thunder and lighting storms, unplug the power cord to prevent damage. All maintenance should be performed by monitor service personnel. All monitors are high voltage. 3
TFT15, 17, 19 Manual_Layout 2 01/03/2013 15:36 Page 4 Setup Connecting the Power Supply Remove the power supply and power cable from the packaging. Insert the power cable connector into the power supply. Plug the DC12V jack into the power socket on the monitor which is indicated as DC. Plug the three pin power plug into the main power socket. NOTE - If there is no signal for approximately 180 seconds, the monitor will enter standby mode. For any input other than PC. The monitor will not enter standby mode automatically. If you are not going to use this monitor for a long time, switch off the power switch on the monitor and disconnect the power plug from the wall outlet. Functions Front Controls of the Monitor INPUT MENU DOWN/- UP/+ POWER Selects which input the monitor will display Opens up options for the monitor s input Navigation and adjustment level Navigation and adjustment level Switches the monitor ON/OFF Remote Controller 1. Power Power supply switch 2. Picture Picture mode 3. Left 12. Right VOL +/- or OK 4. Up / Sub-menu Selection 13. Down S-VIDEO mode shortcut key 5. VGA PC mode 6. AV Video mode 7. S-video S-video mode 8. YPbPr YPbPr mode 9. DVI R/L Menu R/L audio shortcut key 10. HDMI HDMI input 11. MENU Menu enter/exit 14. INPUT Source input 15. MUTE Mute Sound 16. FREEZE Freeze enter and exit 1 2 16 15 14 4 11 3 12 13 5 8 10 6 7 9 4
TFT15, 17, 19 Manual_Layout 2 01/03/2013 15:36 Page 5 To turn the monitor power ON Connect the power supply to the monitor and wall outlet, the power indicator will turn red and the monitor is in Standby Mode. In Standby Mode, press the power button and the indicator will change to blue. NOTE - It takes a few seconds before a picture will appear. To turn the monitor power OFF Pressing the power button while the monitor is on will activate Standby Mode. Then disconnect the power plug from the wall outlet. Input Menu Selecting an Input Press the Input button and then the Menu button to scroll through the input options, select VGA, HDMI, VIDEO1, VIDEO2 by pressing UP/+ or the DOWN/- button. The Input selection refers to the input being used on the monitor Rear Inputs of the Monitor AUDIO OUT IN VIDEO 2 OUT IN VIDEO 1 IN VGA IN HDMI IN DC IN 5
TFT15, 17, 19 Manual_Layout 2 01/03/2013 15:36 Page 6 Video Mode Menu Adjusting the Video Mode Menu By pressing the Menu button, you can access the menu options for; Picture, Audio, OSD, Function. To make adjustments in the Sub-menu, press the UP/+ and DOWN/- button. PICTURE AUDIO OSD FUNCTION 6
TFT15, 17, 19 Manual_Layout 2 01/03/2013 15:36 Page 7 VGA Mode Menu Adjusting the VGA Mode Menu Select VGA mode and press the Menu button, select; PC, Audio, OSD or Function. To make adjustments on the Sub-menu, press the UP/+ and DOWN/-button. PICTURE AUDIO OSD FUNCTION Troubleshooting Incorporated in the monitor are the most up-to-date devices to eliminate interference. Local radiation however, can create disturbances. DIATHERMY: Herringbone pattern and partial picture loss can result from the operation of diathermy equipment from a nearby doctor s surgery or hospital. SNOW: Weak signals from long distant cable runs can give the effect of falling snow. CAR IGNITION: Nearby cars and electrical motors can cause small streaks across the picture or make the picture roll. 7
TFT15, 17, 19 Manual_Layout 2 01/03/2013 15:36 Page 8 Technical Specifications MODEL TFT - 15 TFT - 17 TFT - 19 LCD Display 15 TFT LCD 17 TFT LCD 19 TFT LCD Pixel Pitch 0.297 0.264 0.294 Max. Resolution SXGA (1024 x 768) SXGA(1280 x1024) SXGA(1280 x1024) Contrast Ratio 400:1 1000:1 1000:1 Brightness 300cd/m² 400cd/m² 450cd/m² Response Time 6mS (at 25 C) 5mS (at 25 C) 5mS (at 25 C) Display Color 16.2 million 16.7 million 16.7 million View Angle L+/R- 75/75 80/80 80/80 U+/D- 75/60 80/80 80/80 PC Interface VGA (15Pin D-sub) VGA (15Pin D-sub) VGA (15Pin D-sub) Display Mode VGA, HDMI and VGA, HDMI and VGA, HDMI and CVBS (Video) CVBS (Video) CVBS (Video) Power consumption Approx. 23W Approx. 25W Approx. 33W Frequency Horiz. - 30~60 KHz Horiz. - 30~60 KHz Horiz. - 30~60 KHz Vert. - 56~75 KHz Vert. - 56~75 KHz Vert. - 56~75 KHz Signal Connector VGA Cable VGA Cable VGA Cable OSD Menu On Screen On Screen On Screen Power Adapter DC12V 4A DC12V 4A DC12V 4A Operating Conditions Temp. - 5 C ~ 50 C Temp. : 5 C ~ 50 C Temp. : 5 C ~ 50 C Humidity - < 85%RH Humidity - < 85%RH Humidity - < 85%RH Storage Conditions Temp. - 0 C~40 C Temp. - 0 C~40 C Temp. - 0 C~40 C Humidity - < 95%RH Humidity - < 95%RH Humidity - < 95%RH Certification CE, RoHS CE, RoHS CE, RoHS Elite Security Products Unit 7, Target Park, Shawbank Rd Lakeside, Redditch B98 8YN Telephone: 01527 51 51 50 Fax: 01527 51 51 43 email: info@espuk.com