Custom Installation Notes: Serial programming interface and IR remote commands for Arcam AVR400

Custom Installation Notes: Serial programming interface and IR remote commands for Arcam AVR400 4

Contents Introduction...3 Conventions...3 Command and response formats...3 Serial Cable Specification...3 transfer format...3 AMX Duet Support...4 s...4 s...4 ate changes as a result of other inputs...4 Reserved Commands...4 command and response sequence...4 System Command Specifications...5 Power (0x00)...5 Display Brightness ()...5 Headphones (0x02)...5 FM genre (0x03)...6 Software version (0x04)...6 Restore factory default settings (0x05)...6 Save/Restore secure copy of settings (0x06)...7 Simulate RC5 IR Command (0x08)...7 Display Information Type (0x09)...8 Request current source (0x1D)...9 Headphone Over-ride (0x1F)...9 Input Command Specifications... 10 Video selection (0x0A)...10 Select analogue/digital (0x0B)...10 Set/Request video input type (0x0C)...10 Output Command Specifications... 11 Set/Request Volume ()...11 Request Mute status (0x0E)...11 Request direct mode status (0x0F)...11 Request decode mode status 2ch (0x10)...12 Request Decode mode status MCH (0x11)...12 Request RDS information (0x12)...13 Set/request Video Output Resolution (0x13)...13 Menu Command Specifications... 14 Request menu status (0x14)...14 Request tuner preset (0x15)...14 Tune (0x16)...14 Request DAB station (0x18)...15 Radio Programme Type/Category (0x19)...15 Request DLS/PDT information (0x1A)...15 Request preset details (0x1B)...16 Network Command Specifications... 16 Network playback status (0x1C)...16 Setup Adjustment Command Specifications... 17 Treble Equalisaton (0x35)...17 Bass Equalisation (0x36)...17 Room Equalisation (0x37)...17 Dolby Volume (0x38)...18 Dolby Leveller (0x39)...18 Dolby Volume Calibration Offset (0x3A)...18 Balance (0x3B)...19 Dolby Pro Logic II Dimension (0x3C)...19 Dolby Pro Logic II Centre Width (0x3D)...19 Dolby Pro Logic II Panorama (0x3E)...20 Subwoofer Trim (0x3F)...20 Lipsync Delay (0x40)...20 Compression (0x41)...21 Request incoming video parameters (0x42)...21 Request incoming audio format (0x43)...22 Request incoming audio sample rate (0x44)...23 Set/Request Sub ereo Trim (0x45)...23 Set/Request Brightness (0x46)...23 Set/Request Contrast (0x47)...24 Set/Request Colour (0x48)...24 Set/Request Picture Mode (0x49)...24 Set/Request Edge Enhancement (0x4A)...25 Set/Request Noise Reduction (0x4C)...25 Set/Request MPEG Noise Reduction (0x4D)...26 Set/Request Zone 1 OSD on/off (0x4E)...26 Set/Request Output Frame Rate (0x50)...27 AVR400 RC5 command codes... 28 Basic Functions...28 Tuner Functions...28 Advanced Functions...29 Applicability Publication Reference This is Arcam technical publication SH235E Issue 1.2 (June 2011). AVR400 software version This document applies to AVR400 RS232 protocol version 1.0 as contained within main software version 2.24 The latest version of this document is available on the Arcam Dealer extranet accessed via http://www.arcam.co.uk/extranet. If you cannot yet access the Dealer extranet, please apply by email to scottc@arcam.co.uk. Changelog Issue A.0: First draft release Issue B.0: Added video bypass, Frame Rate Auto & Frame Rate Follow Input RC5 IR commands. Issue C.0: Corrections to Software Version, clarification to several commands. Issue D.0: Removed direct video select IR commands. Added press-and-hold DIRECT to enable RS232 Various corrections according to Anam comments 06-12-2010 Issue E.0: Corrected response to command 0x50 Output Frame Rate. Issue F.0: Added direct video select IR commands Issue 1.0: Corrected version numbers. Production release. Issue 1.1: Corrections to document errors for volume command Issue 1.2: Updated commands 0x18, 0x19 & 0x1A following bugfixes in software version 2.24 2

Controlling the AVR400 via RS232 Introduction Set-up This document describes the remote control protocol for controlling the AVR400 via the RS232 interface. The AVR400 implements virtual IR commands in order to simplify the protocol. Any operation that can be invoked using the IR remote control can be achieved over RS232 using the Simulate RC5 IR command (0x08). See page 7 for details of this command. The RC5 IR code set is listed from page 28. The AVR400 must be correctly configured for RS232 remote control; by default, RS232 control is disabled for minimum standby power consumption. RS232 can be enabled using the front panel: press and hold the front panel direct button for 4 seconds until RS232 PORT ON is displayed on the VFD. Alternatively, RS232 can be enabled using the OSD menu. Press A followed by U on the CR102 remote control in order to access the setup menu. Use the cursor keys < >, ' and O to enter the General Setup menu and locate the option RS232 Control. Press O,, then O to change this parameter to On. Conventions All hexadecimal numbers begin 0x. Any character in single quotes gives the ASCII equivalent of a hex value. <n> represents an unknown or variable number. Serial Cable Specification DB9 Female 1 5 6 9 1 5 6 9 DB9 Female The cable is wired as a null modem: Connector 1 pin Connector 2 pin Function 2 3 Rx Tx 3 2 Tx Rx 5 5 RS232 Ground transfer format Transfer rate: 38,400bps. 1 start bit, 8 data bits, 1 stop bit, no parity, no flow control. Command and response formats Communication between the remote controller (RC) and the AVR400 takes the form of sequences of bytes, with all commands and responses having the same basic format. The AVR400 shall always respond to a received command, but may also send messages at other times. Each transmission by the RC is the following format: <> <> <> <> <> <> (art transmission):! (): see below. (Command code): the code for the command ( length): the number of data items following this item,excluding the ETR : the parameters for the command (End transmission): Each response by the AVR400 is the following format:: <> <> <> <> <> <> <> (art transmission):! (): see below. (Command code): the code for the command (): see below. ( Length): the number of data items following this item, excluding the ETR : the parameters for the response of length n. n is limited to 255. (End transmission): The AVR400 responds to each command from the RC within three seconds. The RC may send further commands before a previous command response has been received. 3

s The following zone numbers are defined: 1. (Zone 1 is the master zone. Commands that appear zone-less refer to the master zone) 0x02 2. s The following answer codes are defined: 0x00 atus update. 0x82 Zone Invalid. 0x83 Command not recognised. 0x84 Parameter not recognised. 0x85 Command invalid at this time.¹ 0x86 Invalid data length. ¹Certain commands cannot be processed when the Setup Menu is being displayed. An answer code of 0x85 will be returned in these circumstances. Also, commands for tuner control cannot be processed when the tuner input is not selected, etc. ate changes as a result of other inputs It is possible that the state of the AVR400 may be changed as a result of user input via the front panel buttons or via the IR remote control. Any change resulting from these inputs is relayed to the RC using the appropriate message type. For example, if the user changed the front panel display brightness using the DISPLAY button on the front panel, a display message (defined below) would be sent to the RC. A similar action would be taken for all other state changes (including decode mode changes). Reserved Commands Commands 0xF0 to 0xFF (inclusive) are reserved for test functions and should never be used. command and response sequence As an example, the command to simulate the RC5 command 16-16, volume up: STR ZONE CC DL 1 2 ETR 0x08 0x02 0x10 0x10 Assuming that the command was accepted by the AV Receiver and is being processed, the AVR400 responds to this command with the following sequence: STR ZONE CC AC DL 1 2 ETR 0x08 0x00 0x02 0x10 0x10 AMX Duet Support The AVR400 shall be fully compatible with AMX Duet Dynamic Device Discovery Protocol (DDDP) The following description of Dynamic Device Discovery comes from the AMX website (www.amx.com). Dynamic Device Discovery is part of AMX s Duet platform, which combines the proven reliability and power of NetLinx with the extensive capabilities of the Java 2 Micro Edition (J2ME) platform. When integrating a serial or IP device from a manufacturer embedding the Dynamic Device Discovery Protocol (DDDP), Duet recognizes the device and loads the appropriate Duet module, which automatically installs the new device. AMX s NetLinx Master can then find and install the Duet device module either from a library on the master, from AMX s Web site, or from the manufacturer s Web site. Duet also allows for device swapping so that programming changes are not required when devices with DDDP are removed or replaced a huge benefit for end users. The Duet platform is an extension AMX s InConcert manufacturer partner program, which was developed to ensure seamless communication between partners devices and the AMX control system. is specified in the ASCII format. All ASCII characters between the quotes should be recognised/transmitted. \r is a carriage return () Command: AMX\r AVR400 AMXB<Device-SDKClass=Receiver><Device-Make=ARCAM><Device-Model=AVR400><Device-Revision=x.y.z>\r Where x.y.z = RS232 protocol version number. 4

System Command Specifications Power (0x00) Request the stand-by state of a zone. Command/response sequence to request the power state of zone 1 where zone 1 has power on: Command: 0x00 0xF0 0x00 0x00 0x00 0xF0 Request power state 0x00 0x00 Zone is in stand-by Zone is powered on Display Brightness () Request the brightness of the display of the AVR400. Command/response sequence for requesting the brightness of the display where the display is off: Command: 0xF0 0x00 0x00 0xF0 Request brightness 0x00 Front panel is off Front panel L1 0x02 Front panel L2 0x03 Front panel L3 Headphones (0x02) Determine whether headphones are connected. Command/response sequence to request the headphone status where the headphones are not connected: Command: 0x02 0xF0 0x02 0x00 0x00 0x02 0xF0 Request current headphone connection status 0x02 ( length) 0x00 Headphones are not connected. Headphones are connected 5

FM genre (0x03) Request information on the current station programme type from FM source in a given zone. If FM is not selected on the given zone an error 0x85 is returned. Command/response sequence to request the programme type on zone 1 where the programme type is POP MUSIC : Command: 0x03 0xF0 0x03 0x00 0x09 0x50 0x4F 0x50 0x20 0x4D 0x55 0x53 0x49 0x43 1 1 <n> 0x03 Request information source: 0xF0 FM program type 0x03 length <n> The radio programme type in ASCII characters Software version (0x04) Request the version number of the various pieces of software on the AVR400. Command/response sequence to request the RS232 protocol version (1.4): Command: 0x04 0xF0 0x04 0x00 0x03 0xF0 0x04 1 2 3 0x04 0xF0 Request RS232 version 0xF1 Request MCU (main) version 0xF2 Request Torino (video processor) version 0xF3 Request DSP version 0xF4 Request USB version 0xF5 Request sub MCU version 0x04 0x03 Echo data from command Major version number Minor version number Restore factory default settings (0x05) Force a restore of the factory default settings. Command/response sequence to restore factory defaults: Command: 0x05 0x02 0xAA 0xAA 0x05 0x00 0x00 1 2 0x05 0x02 0xAA (Confirmation data pattern to avoid accidental restore) 0xAA (Confirmation data pattern to avoid accidental restore) 0x05 0x00 6

Save/Restore secure copy of settings (0x06) Force a restore of the secure copy of the settings. Note: If no secure copy has been made, this command will return an answer code of 0x85. If the system is currently doing a save and another save is requested. The second save will fail silently. If a command 0x1E is being processed this command will fail with a answer code 0x85 Command/response sequence to restore secure backup: Command: 0x06 0x07 0x55 0x55 0x02 0x03 0x04 0x06 0x00 0x00 0X06 0x07 1 0x00 Save secure backup Restore secure backup 2 0x55 (Confirmation data pattern to avoid accidental save/restore) 3 0x55 (Confirmation data pattern to avoid accidental save/restore) 4 Pin digit 1 5 Pin Digit 2 5 Pin Digit 3 7 Pin Digit 4 0x06 0x00 Simulate RC5 IR Command (0x08) Simulate an RC5 command via the RS232 port. An additional status message will be sent in most cases as a result of the IR command. Command/response sequence to RC5 16-17 (AVR volume down in zone 1): Command: 0x08 0x02 0x10 0x11 0x08 0x00 0x02 0x10 0x11 1 2 1 2 0x08 0x02 RC5 System code RC5 Command code 0x08 0x02 RC5 System code RC5 Command code 7

Display Information Type (0x09) Set the VFD display information type (where applicable). The return data echoes the data sent. Command/response sequence to set the display text to show the current AM radio frequency with AM playing in zone 2: Command: 0x02 0x09 0x02 0x09 0x00 0x09 For all sources: 0x00 Set the display to Processing mode 0xE0 Cycle though all displayable information. 0xF0 Request the current display type If the current source is AM: Set the display to Signal strength If the current source is FM: Set the display to Radio text 0x02 Set the display to Programme type 0x03 Set the display to Signal strength If the current source is DAB: Set the display to Radio text 0x02 Set the display to Genre 0x03 Set the display to Signal quality 0x04 Set the display to Bit rate If the current source is NET Set the display to Track 0x02 Set the display to Artist 0x03 - Set the display to Album 0x04 Set the display to audio type 0x05 Set the display to rate If the current source is ipod Set the display to Track 0x02 Set the display to Artist 0x03 - Set the display to Album 0x09 The current display is returned, as for the command. 8

Request current source (0x1D) Request the source currently selected for a given zone. Command/response sequence to request the current source for Zone 1 where the source is set to SAT : Command: 0x1D 0xF0 0x1D 0x00 0x04 0x1D 0xF0 0x1D The current source in the indicated zone: 0x00 Follow Zone 1 CD 0x02 BD 0x03 AV 0x04 SAT 0x05 PVR 0x06 VCR 0x07 0x08 AUX 0x09 DISPLAY 0x0A TUNER (AM) 0x0B TUNER (FM) 0x0C TUNER (DAB) MCH 0x0E NET 0x0F IPOD Headphone Over-ride (0x1F) tivate/deactivate the mute relays (does not zero the volume). Command/response sequence to activate the mute relays: Command: 0x1F 0x1F 0x00 1 0x1F 0x00 Headphone/Over-ride Clear (speakers muted if headphones present) Headphone/Over-ride Set (speakers unmuted if headphones present) 0x1F Relay state 9

Input Command Specifications Video selection (0x0A) Changes the video input. Returns invalid (0x85) if OSD is showing setup screen. Command/response sequence to change the video source for zone 1 to PVR : Command: 0x0A 0x03 0x0A 0x00 0x03 0x0A Source: 0x00 BD SAT 0x02 AV 0x03 PVR 0x04 VCR 0xF0 Request current input 0x0A The current video source is returned, as for the command Select analogue/digital (0x0B) Select an analogue/digital audio input for the current source. Returns invalid (0x85) if OSD is showing setup screen. Command/response sequence to change the audio input to digital in zone 1: Command: 0x0B 0x0B 0x00 0x0B 0x00 Use the analogue audio for the current source. Use the digital audio for the current source (if available). 0x02 Use HDMI for the current source (if available). 0xF0 Request the audio type in use for the current source. 0x0B 0x00 Analogue audio is in use for the current source. Digital audio is in use for the current source. 0x02 HDMI audio is in use for the current source. Set/Request video input type (0x0C) Set/request the video input (CVBS/S-video/Component/HDMI) type in use for the current source. This command is only valid for zone 1. Command/response sequence for requesting the input video source where it is S-video: Command: 0x0C 0xF0 0x0C 0x00 0x03 0x0C HDMI. 0x02 Component. 0x03 S-Video. 0x04 CVBS. 0xF0 Request the video type in use for the current source. 0x0C HDMI. 0x02 Component. 0x03 S-Video. 0x04 CVBS. 10

Output Command Specifications Set/Request Volume () Set or request the volume of a zone. This command returns the volume even if the zone requested is in mute. The Request Mute status command can be used to discover if the zone is muted. Response data format: e.g. for volume 42dB: 1=0x2A (42) Command/response sequence for setting the volume in Zone 1 to 45dB: Command: 0x2D 0x00 0x2D 1 0x00 (0) 0x63 (99) Set the volume 0xF0 Request the current volume Zone volume, integer value: 0x00 (0) 0x63 (99) Request Mute status (0x0E) Request the mute status of the audio in a zone. Command/response sequence to request the mute status of zone 1 where zone 1 is muted: Command: 0x0E 0xF0 0x0E 0x00 0x00 P2 0x0E 0xF0 Request mute status 0x0E 0x00 Zone is muted Zone is not muted Request direct mode status (0x0F) Request the direct mode status on Zone 1. Command/response sequence to request the Direct mode status in zone 1 where the mode is direct: Command: 0x0F 0xF0 0x0F 0x00 0x0F 0xF0 Request mode setting 0x0F 0x00 Direct mode is off Direct mode is on 11

Request decode mode status 2ch (0x10) Request the decode mode for two-channel material in zone 1. Command/response sequence to request the decode mode in zone 1 where the mode is Pro Logic II / x Movie Mode: Command: 0x10 0xF0 0x10 0x00 0x02 0x10 0xF0 Request decode mode 0x10 ereo 0x02 Pro Logic II / x Movie Mode 0x03 Pro Logic II / x Music Mode 0x04 Pro Logic II Matrix 0x05 Pro Logic II Game 0x06 Dolby Pro Logic Emulation 0x07 Neo:6 Cinema 0x08 Neo:6 Music Request Decode mode status MCH (0x11) Request the decode mode for multi-channel material in zone 1. Command/response sequence to request the decode mode in zone 1 where the mode is Pro Logic IIx Movie Mode: Command: 0x11 0xF0 0x11 0x00 0x04 0x11 0xF0 Request decode mode 0x11 ereo down-mix 0x02 Multi-channel mode 0x03 - Dolby EX / DTS-ES mode 0x04 Pro Logic IIx movie mode 0x05 - Pro Logic IIx music mode 12

Request RDS information (0x12) Request RDS information from the current radio station in a given zone. If FM is not selected on the given zone an error 0x85 is returned. Command/response sequence to request the RDS information on FM in zone 1, where the response is Playing your favourite music. Command: 0x12 0xF0 0x12 0x00 0x1C 0x00 0x50 0x6C 0x61 0x79 0x69 0x6E 0x67 0x20 0x79 0x6F 0x75 0x72 0x20 0x66 0x61 0x76 0x6F 0x75 0x72 0x69 0x74 0x65 0x20 0x6D 0x75 0x73 0x69 0x63 1 1 <n> 0x12 Request information source: 0xF0 FM 0x12 length <n> The radio programme type in ASCII characters Set/request Video Output Resolution (0x13) Set/request the Video Output Resolution of zone 1. Command/response sequence to request the video output in zone 1 where the resolution is 1080p: Command: 0x13 0xF0 0x13 0x00 0x05 0x13 Set resolution to SD Interlaced. 0x02 Set resolution to SD Progressive. 0x03 Set resolution to 720p. 0x04 Set resolution to 1080i. 0x05 Set resolution to 1080p. 0x06 Set resolution to Preferred. 0x07 Set resolution to Bypass. 0xF0 Request the video output. 0xF1 Increment the resolution setting. 0xF2 Decrement the resolution setting. 0x13 SD Interlaced. 0x02 SD Progressive. 0x03 720p. 0x04 1080i. 0x05 1080p 0x06 Preferred 0x07 Bypass 13

Menu Command Specifications Request menu status (0x14) Request which (if any) menu is open in the unit. Command/response sequence to request which menu is open where the Trim menu is open: Command: 0x14 0xF0 0x14 0x00 0x03 0x14 0xF0 Request the open menu state 0x14 0x00 No menu is open 0x02 Set-up Menu Open 0x03 Trim Menu Open 0x04 Bass Menu Open 0x05 Treble Menu Open 0x06 Sync Menu Open 0x07 Sub Menu Open 0x08 Tuner Menu Open 0x09 Network menu Open 0x0A ipod Menu Open Request tuner preset (0x15) Request the current tuner preset number. If the tuner is not selected on the given zone an error 0x85 is returned. Command/response sequence to request the preset number where the present number is 10 on zone 1: Command: 0x15 0xF0 0x15 0x00 0x0A 0x15 0x32 (1-50) number of required preset. 0xF0 Request the current preset number. 0x15 0xFF Currently no preset selected - 0x32: (1-50) the current preset number. Tune (0x16) Increment/Decrement the tuner frequency in 0.05MHz steps (FM) or 9/10KHz steps (AM). The returned frequency is calculated as follows: AM freq. (khz) = ((1000 s & 100 s) * 100) + (10 s & 1 s) FM freq. (MHz) = reported freq. (MHz) FM freq. (khz) = reported freq. (khz) For these reasons, this command may return values that cannot be translated into ASCII characters. If the tuner is not selected on the given zone an error 0x85 is returned. Command/response sequence to increment the FM tuning from 85.0MHz to 85.05MHz in zone 1: Command: 0x16 0x16 0x00 0x02 0x55 0x05 1 1 2 0x16 0x00 Decrement tuner frequency by 1 step. Increment tuner frequency by 1 step. 0xF0 Request the current tuner frequency. 0x16 0x02 ( length) AM: New frequency (1000 s & 100 s khz) FM: New frequency (MHz) AM: New frequency (10 s & 1 s khz) FM: New frequency (10 s khz) 14

Request DAB station (0x18) Request the current DAB station selected. If DAB is not selected on the given zone an error 0x85 is returned. Command/response sequence to request the DAB station selection where the station is called DAB STATION 2 in zone 1: Command: 0x18 0xF0 0x18 0x00 0x10 0x44 0x41 0x42 0x20 0x53 0x54 0x41 0x54 0x49 0x4F 0x4E 0x20 0x32 0x20 0x20 0x20 1 128 0x18 0xF0 Request the current DAB station 0x18 length, fixed to 16 bytes (ASCII characters) The service label of the DAB station in ASCII characters. The data is padded to 16 bytes with the space character (0x20) Radio Programme Type/Category (0x19) Request information on the current station programme type from DAB source in a given zone. If DAB is not selected on the given zone an error 0x85 is returned. Command/response sequence to request the programme type on zone 1 where the programme type is POP MUSIC : Command: 0x19 0xF0 0x19 0x00 0x10 0x50 0x4F 0x50 0x20 0x4D 0x55 0x53 0x49 0x43 0x20 0x20 0x20 0x20 0x20 0x20 0x20 1 1 128 0x19 Request information source: 0xF0 DAB program type 0x19 length, fixed to 16 bytes (ASCII characters) The radio programme type in ASCII characters. The data is padded to 16 bytes with the space character (0x20) Request DLS/PDT information (0x1A) Request DLS/PDT information (digital radio text) from the current radio station in a given zone. If DAB is not selected on the given zone an error 0x85 is returned. Command/response sequence to request the DLS information on DAB in zone 1, where the response is Playing your favourite music. Command: 0x1A 0xF0 0x1A 0x00 0x80 0x00 0x50 0x6C 0x61 0x79 0x69 0x6E 0x67 0x20 0x79 0x6F 0x75 0x72 0x20 0x66 0x61 0x76 0x6F 0x75 0x72 0x69 0x74 0x65 0x20 0x6D 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 0x20 1 1 <n> 0x1A Request information source: 0xF0 DAB 0x1A length, fixed to 128 bytes (ASCII characters) The radio programme type in ASCII characters. The data is padded to 128 bytes with the space character (0x20) 15

Request preset details (0x1B) Request details of tuner presets. Command/response sequence to request preset 1 where the response is a preset on DAB called DAB STATION 2 : Command: 0x1B 0x1B 0x00 0x0F 0x02 0x44 0x41 0x42 0x20 0x53 0x54 0x41 0x54 0x49 0x4F 0x4E 0x20 0x32 1 2 3 4 0x1B - 0x32: (1-50) The number of the required preset 0x1B length <n> - 0x32: (1-50) The number of the requested preset 0x00 : AM frequency : FM frequency 0x02 : FM RDS name 0x03 : DAB AM: New frequency (1000 s & 100 s khz) FM: New frequency (MHz) AM: New frequency (10 s & 1 s khz) FM: New frequency (10 skhz) <n> The name (DAB, FM if RDS) in ASCII characters Network Command Specifications Network playback status (0x1C) Network message format. If the network is not selected on the given zone an error 0x85 is returned. Command/response sequence where the network module is playing a file File. mp3 on zone 1: Command: 0x1C 0xF0 0x1C 0x00 0x09 0x46 0x69 0x6C 0x65 0x2e 0x6d 0x70 0x33 1 2 <n> 0x1C 0xF0 Request Network playback status 0x1C length <n> 0x00 Navigating Playing 0x02 Paused 0xFF - Busy/Not Playing name of folder in ASCII if navigating name of file in ASCII if playing or paused 16

Setup Adjustment Command Specifications Treble Equalisaton (0x35) Adjust the amount of treble equalisation. Command/response sequence to set the treble to -2dB: Command: 0x35 0x82 0x35 0x00 0x82 1 0x35 0x00 0x0C Set treble to 0dB +12dB 0x81 0x8C Set treble to -1dB -12dB 0xF0 Request current treble value 0xF1 Increment treble by 1dB 0xF2 Decrement treble by 1dB 0x35 0x00 0x0C Treble is 0dB +12dB 0x81 0x8C Treble is -1dB -12dB Bass Equalisation (0x36) Adjust the amount of bass equalisation. Command/response sequence to increase the bass EQ by 1dB when it was 0dB: Command: 0x36 0xF1 0x36 0x00 1 0x36 0x00 0x0C Set bass to 0dB +12dB 0x81 0x8C Set bass to -1dB -12dB 0xF0 Request current bass value 0xF1 Increment bass by 1dB 0xF2 Decrement bass by 1dB 0x36 0x00 0x0C Bass is 0dB +12dB 0x81 0x8C Bass is -1dB -12dB Room Equalisation (0x37) Turn the room equalisation system on/off. Command/response sequence to turn the room equalisation system on: Command: 0x37 0xF1 0x37 0x00 1 0x37 0xF0 Request current Room EQ state 0xF1 Room EQ on 0xF2 Room EQ off 0x37 0x00 Room EQ is off Room EQ is on 0x02 Room EQ has not been calculated and is therefore off 17

Dolby Volume (0x38) Control the status of the Dolby volume system. Command/response sequence to turn the Dolby Volume system on: Command: 0x38 0x38 0x00 0x02 1 0x38 0x00 Dolby Volume off Dolby Volume on 0xF0 Request current Dolby Volume mode 0x38 0x00 Dolby Volume is off Dolby Volume is on Dolby Leveller (0x39) Control the status of the leveller component of the Dolby volume system. Command/response sequence to set the Dolby Leveller to 5: Command: 0x39 0x05 0x39 0x00 0x05 0x39 0x00 0x0A Set Dolby Leveller to 0 10 0xF0 Request current Dolby Leveller setting 0xF1 Increment Dolby Leveller setting 0xF2 Decrement Dolby Leveller setting 0xFF Turn off Dolby Leveller 0x39 1 0x00 0x0A Dolby Leveller setting is 0 10 0xFF Dolby Leveller is off Dolby Volume Calibration Offset (0x3A) Adjust the calibration offset of the Dolby volume system. Command/response sequence to set the calibration offset to -5dB: Command: 0x3A 0x85 0x3A 0x00 0x85 1 0x3A 0x00 0x0F Set the calibration offset to 0 15dB 0x80 0x8F Set the calibration offset to -1-15dB 0xF0 Request current calibration offset 0xF1 Increment the calibration offset by 1dB 0xF2 Decrement the calibration offset by 1dB 0x3A 0x00 0x0F Calibration offset is 0 15dB 0x80 0x8F Calibration offset is -1-15dB 18

Balance (0x3B) Adjust the balance control. Command/response sequence to set the balance to -3: Command: 0x3B 0x83 0x3B 0x00 0x83 0x3B 0x00 0x06 Set the balance to 0 6 0x81 0x86 Set the balance to -1-6 0xF0 Request current balance 0xF1 Increment the balance by 1dB 0xF2 Decrement the balance by 1dB 0x3B 1 0x00 0x06 Balance is 0 6 0x81 0x86 Balance is -1-6 Dolby Pro Logic II Dimension (0x3C) Adjust the Dimension parameter of the Dolby Pro Logic II processor. Command/response sequence to set the dimension to -1: Command: 0x3C 0x81 0x3C 0x00 0x81 0x3C 0x00 0x03 Set the Pro Logic II Dimension parameter to 0 3 0x81 0x83 Set the Pro Logic II Dimension parameter to -1-3 0xF0 Request current Pro Logic II Dimension setting 0xF1 Increment the Pro Logic II Dimension 0xF2 Decrement the Pro Logic II Dimension 0x3C 1 0x00 0x03 The Pro Logic II Dimension parameter is 0 3 0x81 0x83 The Pro Logic II Dimension parameter is -1-3 Dolby Pro Logic II Centre Width (0x3D) Adjust the Centre Width parameter of the Dolby Pro Logic II processor. Command/response sequence to set the centre width to 3: Command: 0x3D 0x03 0x3D 0x00 0x03 0x3D 0x00 0x07 Set the Pro Logic II Centre Width parameter to 0 7 0xF0 Request current Pro Logic II Centre Width setting 0xF1 Increment the Pro Logic II Centre Width 0xF2 Decrement the Pro Logic II Centre Width 0x3D 1 0x00 0x07 The Pro Logic II Centre Width parameter is 0 7 19

Dolby Pro Logic II Panorama (0x3E) Turn on/off the Panorama setting of the Dolby Pro Logic II processor. Command/response sequence to turn Dolby Pro Logic II Panorama on: Command: 0x3E 0xF1 0x3E 0x00 0xF1 1 0x3E 0xF0 Request current Pro Logic II Panorama setting 0xF1 Set Dolby Pro Logic II Panorama on 0xF2 Set Dolby Pro Logic II Panorama off 0x3E 0x00 Dolby Pro Logic II Panorama is off Dolby Pro Logic II Panorama is on Subwoofer Trim (0x3F) Adjust the value of subwoofer trim. Command/response sequence to set the subwoofer trim to -1.5dB: Command: 0x3F 0x85 0x3F 0x00 0x85 1 0x3F 0x00 0x14 Set positive subwoofer trim in 0.5dB steps (e.g. 0x02 = +1.0dB) 0x81 0x94 Set negative sub. trim in 0.5dB steps (e.g. 0x82 = -1.0dB) 0xF0 Request current subwoofer trim value 0xF1 Increment the subwoofer trim by 1dB 0xF2 Decrement the subwoofer trim by 1dB 0x3F 0x00 0x14 Positive subwoofer trim in 0.5dB steps (e.g. 0x02 = +1.0dB) 0x81 0x94 Negative subwoofer trim in 0.5dB steps (e.g. 0x82 = -1.0dB) Lipsync Delay (0x40) Adjust the lipsync delay value. Command/response sequence to set the lipsync delay to 50ms: Command: 0x40 0x0A 0x40 0x00 0x0A 1 0x40 0x00 0x32 set the lipsync delay in 5ms steps (e.g. 0x08 = 40ms) 0xF0 Request current lipsync delay value 0xF1 Increment the lipsync delay by 5ms 0xF2 Decrement the lipsync delay by 5ms 0x40 0x00 0x32 the lipsync delay in 5ms steps (e.g. 0x10 = 80ms) 20

Compression (0x41) Adjust the dynamic range compression setting. Command/response sequence to set compression to medium: Command: 0x41 0x41 0x00 1 0x41 0x00 Compression off Set compression to medium 0x02 Set compression to high 0xF0 Request current compression setting 0x41 0x00 Compression off medium 0x02 high Request incoming video parameters (0x42) Request the incoming video resolution, refresh rate and aspect ratio. Command/response sequence to request video parameters, where the video is 1280x720 (720p) 50Hz 16:9: Command: 0x42 0xF0 0x42 0x00 0x07 0x05 0x00 0x02 0xD0 0x32 0x00 0x02 0x42 0xF0 Request incoming video parameters 0x42 0x07 1 Horizontal resolution MSB (e.g. for 720p: 0x05 since 1280 = 0x0500) 2 Horizontal resolution LSB (e.g. for 720p: 0x00 since 1280 = 0x0500) 3 Vertical resolution MSB (e.g. for 720p: 0x02 since 720 = 0x02D0) 4 Vertical resolution LSB (e.g. for 720p: 0xD0 since 720 = 0x02D0) 5 Refresh rate for full image update (half the field rate for interlaced signals) (e.g. for 50Hz progressive: 0x32) 6 Interlaced flag: 0x00 Progressive Interlaced 7 Aspect ratio: 0x00 Undefined 4:3 0x02 16:9 21

Request incoming audio format (0x43) Request the incoming audio format. Command/response sequence to request the incoming audio format, where the format is Dolby Digital 5.1: Command: 0x43 0xF0 0x43 0x00 0x02 0x02 0x1A 0xD0 1 2 0x43 0xF0 Request incoming audio format 0x43 0x02 Audio stream format: 0x00 PCM Analogue Direct 0x02 Dolby Digital 0x03 Dolby Digital EX 0x04 Dolby Digital Surround 0x05 Dolby Digital Plus 0x06 Dolby Digital True HD 0x07 DTS 0x08 DTS 96/24 0x09 DTS ES Matrix 0x0A DTS ES Discrete 0x0B DTS ES Matrix 96/24 0x0C DTS ES Discrete 96/24 DTS HD Master Audio 0x0E DTS HD High Res Audio 0x0F DTS Low Bit Rate 0x10 DTS Core 0x13 PCM Zero 0x14 Unsupported 0x15 Undetected Audio channel configuration: 0x00 Dual Mono Centre only 0x02 ereo only 0x03 ereo + mono surround 0x04 ereo + Surround L & R 0x05 ereo + Surround L & R + mono Surround Back 0x06 ereo + Surround L & R + Surround Back L & R 0x07 ereo + Surround L & R containing matrix information for surround back L&R 0x08 ereo + Centre 0x09 ereo + Centre + mono surround 0x0A ereo + Centre + Surround L & R 0x0B ereo + Centre + Surround L & R + mono Surround Back 0x0C ereo + Centre + Surround L & R + Surround Back L & R ereo + Centre + Surround L & R containing matrix information for surround back L&R 0x0E ereo Downmix Lt Rt 0x0F ereo Only (Lo Ro) 0x10 Dual Mono + LFE 0x11 Centre + LFE 0x12 ereo + LFE 0x13 ereo + single surround + LFE 0x14 ereo + Surround L & R + LFE 0x15 ereo + Surround L & R + mono Surround Back + LFE 0x16 ereo + Surround L & R + Surround Back L & R + LFE 0x17 ereo + Surround L & R + LFE 0x18 ereo + Centre + LFE containing matrix information for surround back L&R 0x19 ereo + Centre + single surround + LFE 0x1A ereo + Surround L & R + LFE (andard 5.1) 0x1B ereo + Centre + Surround L & R + mono Surround Back + LFE (6.1, e.g. DTS ES Discrete) 0x1C ereo + Centre + Surround L & R + Surround Back L & R + LFE (7.1) 0x1D ereo + Centre + Surround L & R + LFE, containing matrix information for surround back L&R (6.1 e.g. Dolby Digital EX) 0x1E ereo Downmix (Lt Rt) + LFE 0x1F ereo Only (Lo Ro) + LFE 0x20 Unknown Undetected 22

Request incoming audio sample rate (0x44) Request the incoming audio sample rate. Command/response sequence to request the incoming audio sample rate, where the rate is 48kHz: Command: 0x44 0xF0 0x44 0x00 0x02 1 0x44 0xF0 Request incoming audio sample rate 0x44 Incoming audio sample rate: 0x00 32 KHz 44.1 KHz 0x02 48 KHz 0x03 88.2 KHz 0x04 96 KHz 0x05 176.4 KHz 0x06 192 KHz 0x07 Unknown 0x08 Undetected Set/Request Sub ereo Trim (0x45) Set/Request the subwoofer trim value for stereo mode. Command/response sequence to set the sub stereo trim to -1.5dB: Command: 0x45 0x83 0x45 0x00 0x83 1 0x45 0x00 set the Sub ereo Trim value to 0dB 0x81 0x94 set the Sub ereo Trim value to -0.5dB -10.00dB 0xF0 Request Sub ereo Trim value 0xF1 Increment Sub ereo Trim value by 0.5dB 0xF2 Decrement Sub ereo Trim value by 0.5dB 0x45 0x00, 0x81 0x8A Sub ereo Trim value in -0.5dB steps Set/Request Brightness (0x46) Set/Request the brightness control value. Command/response sequence to set the brightness to -4: Command: 0x46 0x84 0x46 0x00 0x84 0x46 0x00 0x32 set the Brightness value to 0 50. 0x81 0xB2 set the Brightness value to -1-50. 0xF0 Request the current Brightness value. 0xF1 Increment Brightness value by 1. 0xF2 Decrement Brightness value by 1. 0x46 1 0x00 0x32 Brightness value 0 50 0x81 0xB2 Brightness value -1-50 23

Set/Request Contrast (0x47) Set/Request the contrast control value. Command/response sequence to set the contrast to 4: Command: 0x47 0x04 0x47 0x00 0x04 0x47 0x00 0x32 set the Contrast value to 0 50. 0x81 0xB2 set the Contrast value to -1-50. 0xF0 Request the current Contrast value. 0xF1 Increment Contrast value by 1. 0xF2 Decrement Contrast value by 1. 0x47 1 0x00 0x32 Contrast value 0 50 0x81 0xB2 Contrast value -1-50 Set/Request Colour (0x48) Set/Request the colour control value. Command/response sequence to increment the colour value, where the value becomes +3: Command: 0x48 0xF1 0x48 0x00 0x03 0x48 0x00 0x32 set the Colour value to 0 50. 0x81 0xB2 set the Colour value to -1-50. 0xF0 Request the current Colour value. 0xF1 Increment Colour value by 1. 0xF2 Decrement Colour value by 1. 0x48 1 0x00 0x32 Colour value 0 50 0x81 0xB2 Colour value -1-50 Set/Request Picture Mode (0x49) Set/Request the Picture Mode. Command/response sequence to request the current picture mode, where the picture mode is Video: Command: 0x49 0xF0 0x49 0x00 1 0x49 0x00 Set Picture Mode to Auto. Set Picture Mode to Video. 0x02 Set Picture Mode to Film. 0xF0 Request current Picture Mode. 0xF1 Increment Picture Mode value by 1. 0xF2 Decrement Picture Mode value by 1. 0x49 0x00 Picture Mode is Auto. Picture Mode is Video. 0x02 Picture Mode is Film. 24

Set/Request Edge Enhancement (0x4A) Set/Request the Edge Enhancement value. Command/response sequence to set the Edge Enhancement value to 10: Command: 0x4A 0x0A 0x4A 0x00 0x0A 0x4A 0x00 0x32 Set the Edge Enhancement value to 0 50. 0xF0 Request current Edge Enhancement value. 0xF1 Increment Edge Enhancement value by 1. 0xF2 Decrement Edge Enhancement value by 1. 0x4A 1 0x00 0x32 Edge Enhancement value to 0 50. Set/Request Noise Reduction (0x4C) Set/Request the Noise Reduction value. Command/response sequence to set the Noise Reduction value to Low : Command: 0x4C 0x4C 0x00 1 0x4C 0x00 Set Noise Reduction to Off. Set to Noise Reduction to Low. 0x02 Set Noise Reduction to Medium. 0x03 Set Noise Reduction to High. 0xF0 Request current Noise Reduction value. 0xF1 Increment Noise Reduction value by 1. 0xF2 Decrement Noise Reduction value by 1. 0x4C 0x00 Noise Reduction is Off. Noise Reduction is Low. 0x02 Noise Reduction is Medium. 25

Set/Request MPEG Noise Reduction (0x4D) Set/Request the MPEG Noise Reduction value. Command/response sequence to set the MPEG Noise Reduction value to Off : Command: 0x4A 0x00 0x4A 0x00 0x00 1 0x4D 0x00 Set MPEG Noise Reduction to Off. Set to MPEG Noise Reduction to Low. 0x02 Set MPEG Noise Reduction to Medium. 0x03 Set MPEG Noise Reduction to High. 0xF0 Request current MPEG Noise Reduction value. 0xF1 Increment MPEG Noise Reduction value by 1. 0xF2 Decrement MPEG Noise Reduction value by 1. 0x4D 0x00 MPEG Noise Reduction is Off. MPEG Noise Reduction is Low. 0x02 MPEG Noise Reduction is Medium. 0x03 MPEG Noise Reducton is High. Set/Request Zone 1 OSD on/off (0x4E) Set/Request whether the Zone 1 OSD is shown. Command/response sequence to set the Zone 1 OSD to Off : Command: 0x4A 0xF2 0x4A 0x00 0x00 1 0x4E 0xF0 Request current Zone 1 OSD on/off state. 0xF1 Set Zone 1 OSD to On. 0xF2 Set Zone 1 OSD to Off. 0x4E 0x00 Zone 1 OSD is On. Zone 1 OSD is Off. 26

Set/Request Output Frame Rate (0x50) Set/Request the video output frame rate. Command/response sequence to set the frame rate to Auto: Command: 0x50 0x00 0x50 0x00 0x00 1 0x50 0x00 Set the frame rate to Auto. Set the frame rate to follow the source. 0x02 Set the frame rate to 50Hz. 0x03 Set the frame rate to 60Hz. 0xF0 Request the current frame rate. 0xF1 Increment setting. 0xF2 Decrement setting. Zone Number 0x50 0x00 Auto. Frame rate is set to follow the source. 0x02 50Hz. 0x03 60Hz. 27

AVR400 RC5 command codes These codes are recognised as infra-red signals received by the front panel, RC5 electrical signals received by the remote in jacks and as RS232 data using the Simulate RC5 IR Command (0x 08). Basic Functions These RC5 codes are present on the supplied IR remote control and provide control over basic amplifier and video processing functions. Tuner Functions These RC5 codes are present on the supplied IR remote control and provide control over the tuner sources within the AVR400 system. Function RC5 code [systemcommand] Decimal RC5 code (1-2) Hexadecimal andby 16-12 0x10-0x0C Select Phono 16-1 0x10 - Select AV 16-2 0x10-0x02 Select Tuner 16-3 0x10-0x03 Select BD 16-4 0x10-0x04 Select Display (Audio Return Channel) 16-5 0x10-0x05 Select VCR 16-6 0x10-0x06 Select CD 16-7 0x10-0x07 Select Aux 16-8 0x10-0x08 Select MCH 16-9 0x10-0x09 Select SAT 16-0 0x10-0x00 Select PVR 16-34 0x10-0x22 Random 16-48 0x10-0x30 Repeat 16-49 0x10-0x31 Select ipod 16-18 0x10-0x12 Select NET 16-11 0x10-0x0B Navigate Up 16-86 0x10-0x56 Navigate Left 16-81 0x10-0x51 OK 16-87 0x10-0x57 Navigate Right 16-80 0x10-0x50 Navigate Down 16-85 0x10-0x55 Cycle between decoding modes (MODE) 16-32 0x10-0x20 Enter system menu (MENU) 16-82 0x10-0x52 Mute 16-13 0x10 - Change VFD brightness (DISP) 16-59 0x10-0x3B Decrease volume (-) 16-17 0x10-0x11 Increase volume (+) 16-16 0x10-0x10 CH- (track back symbol) 16-57 0x10-0x39 Function RC5 code [systemcommand] Decimal RC5 code (1-2 Hexadecimal Numeric entry - 1 17-1 0x11 - Numeric entry - 2 17-2 0x11-0x02 Numeric entry - 3 17-3 0x11-0x03 Numeric entry - 4 17-4 0x11-0x04 Numeric entry - 5 17-5 0x11-0x05 Numeric entry - 6 17-6 0x11-0x06 Numeric entry - 7 17-7 0x11-0x07 Numeric entry - 8 17-8 0x11-0x08 Numeric entry - 9 17-9 0x11-0x09 Numeric entry - 0 17-0 0x11-0x00 Navigate Up / Increment Preset 17-86 0x11-0x56 Navigate Left / Decrease Tuning 17-78 0x11-0x4E OK / SELECT 17-87 0x11-0x57 Navigate Right / Increase Tuning 17-77 0x11-0x4D Navigate Down / Decrement Preset 17-85 0x11-0x55 BAND 17-50 0x11-0x32 MENU 17-125 0x11-0x7D Change VFD Brightness (DISP) 17-18 0x11-0x12 Preset - (CH- / track back symbol) 17-33 0x11 - Preset + (CH+ / track fwd symbol) 17-32 0x11-0x20 Select AM 17-53 0x11-0x35 Select FM 17-52 0x11-0x34 Select FM 17-127 0x11-0x7F Select DAB 17-126 0x11-0x7E Page Up (preset list) 17-38 0x11-0x26 Page Down (preset list) 17-37 0x11-0x25 Delete selected preset 17-41 0x11-0x29 Cycle between VFD information panels 17-15 0x11-0x0F CH+ (track fwd symbol) 16-56 0x10-0x38 tivate DIRECT mode 16-10 0x10-0x0A Room EQ on/off / NET Now Playing screen / IPOD Play/Pause 16-30 0x10-0x1E Toggle Dolby Volume on/off / NET & IPOD Play/Pause 16-70 0x10-0x46 cess Bass control 16-39 0x10-0x27 cess Speaker Trim controls 16-37 0x10-0x25 cess Lipsync Delay control / NET & IPOD op 16-50 0x10-0x32 cess Subwoofer Trim control 16-51 0x10-0x33 cess Treble control 16-14 0x10-0x0E FAV+ / red / Page Up 16-41 0x10-0x29 FAV- / green / Page Down 16-42 0x10-0x2A HOME / yellow 16-43 0x10-0x2B Cycle between VFD information panels / blue 16-55 0x10-0x37 Change control to next zone 16-95 0x10-0x5F Set selected zone to Follow Zone 1 16-20 0x10-0x14 Cycle between output resolutons 16-47 0x10-0x2F Cycle between aspect ratios (Auto, 16:9, 4:3) 16-19 0x10-0x13 Power On 16-123 0x10-0x7B Power Off 16-124 0x10-0x7C 28

Advanced Functions These RC5 codes are not present on the supplied remote control but have been created for custom install use. In order for the AVR400 to respond to these codes they must be transmitted from a programmable IR remote control or over RS232 using the Simulate RC5 IR Command (0x08). Function RC5 Code [system-command] Decimal RC5 Code (1-2) Hexadecimal Function RC5 Code [system-command] Decimal RC5 Code (1-2) Hexadecimal Direct mode On 16-78 0x10-0x4E Direct mode Off 16-79 0x10-0x4F PL II / IIx Game 16-102 0x10-0x66 PL II / IIx Movie 16-103 0x10-0x67 PL II / IIx Music 16-104 0x10-0x68 Multi Channel 16-106 0x10-0x6A ereo 16-107 0x10-0x6B PL 16-110 0x10-0x6E DTS Neo:6 Cinema 16-111 0x10-0x6F DTS Neo:6 Music 16-112 0x10-0x70 Dolby EX 16-118 0x10-0x76 Mute On 16-119 0x10-0x77 Mute Off 16-120 0x10-0x78 NET 16-53 0x10-0x35 FM 16-54 0x10-0x36 AM 16-52 0x10-0x34 DAB 16-72 0x10-0x48 Video VCR-CVBS 16-58 0x10-0x3A Video AV-CVBS 16-60 0x10-0x3C Video SAT-CVBS 16-62 0x10-0x3E Video BD-CVBS 16-71 0x10-0x47 Video VCR-Svid 16-77 0x10-0x4D Video AV-Svid 16-83 0x10-0x53 Video SAT-Svid 16-88 0x10-0x58 Video BD-Svid 16-89 0x10-0x59 Video VCR-HDMI 16-90 0x10-0x5A Video AV-HDMI 16-91 0x10-0x5B Video PVR-HDMI 16-92 0x10-0x5C Video SAT-HDMI 16-93 0x10-0x5D Video BD-HDMI 16-94 0x10-0x5E Lip Sync +5ms 16-100 0x10-0x64 Lip sync -5ms 16-101 0x10-0x65 Frame Rate Auto 16-63 0x10-0x3F Frame Rate 50 16-64 0x10-0x40 Frame Rate 60 16-65 0x10-0x41 Frame Rate Follow Input 16-66 0x10-0x42 Display Off 16-31 0x10-0x1F Display L1 16-33 0x10 - Display L2 16-35 0x10-0x23 Display L3 16-36 0x10-0x24 Balance left 16-38 0x10-0x26 Balance right 16-40 0x10-0x28 Bass +1 16-44 0x10-0x2C Bass -1 16-45 0x10-0x2D Treble +1 16-46 0x10-0x2E Treble -1 16-98 0x10-0x62 Zone 2 Power On 23-123 0X17-0x7B Zone 2 Power Off 23-124 0x17-0x7C Zone 2 Vol+ 23-1 0x17 - Zone 2 Vol- 23-2 0x17-0x02 Zone 2 Mute 23-3 0x17-0x03 Zone 2 Mute On 23-4 0x17-0x04 Zone 2 Mute Off 23-5 0x17-0x05 Zone 2 CD 23-6 0x17-0x06 Zone 2 BD 23-7 0x17-0x07 Zone 2 SAT 23-8 0x17-0x08 Zone 2 AV 23-9 0x17-0x09 Zone 2 VCR 23-11 0x17-0x0B Zone 2 Aux 23-13 0x17 - Zone 2 FM 23-14 0x17-0x0E Zone 2 AM 23-15 0x17-0x0F Zone 2 DAB 23-16 0x17-0x10 Zone 2 ipod 23-18 0x17-0x12 Zone 2 NET 23-19 0x17-0x13 Sub trim +0.5dB 16-105 0x10-0x69 Sub trim -0.5dB 16-108 0x10-0x6C PLII Music Centre +1 16-109 0x10-0x6D PLII Music Centre -1 16-113 0x10-0x71 PLII Music Dimension +1 16-114 0x10-0x72 PLII Music Dimension -1 16-115 0x10-0x73 PLII Panorama On 16-116 0x10-0x74 PLII Panorama Off 16-117 0x10-0x75 Video out Preferred/Best 16-125 0x10-0x7D Video out SD Prog 16-15 0x10-0x0F Video out 720p 16-23 0x10-0x17 Video out 1080i 16-26 0x10-0x1A Video out 1080p 16-27 0x10-0x1B Video out Bypass 16-28 0x10-0x1C 29

23425 30 SH235E Issue 1.2 A&R Cambridge Ltd, Pembroke Avenue, Waterbeach, CAMBRIDGE CB25 9QR, England +44 (0)1223 203200... http://www.arcam.co.uk/extranet