Introduction Mackie s -VZ PRO combines the compact size of the 0-VZ PRO with added features and mm log-taper faders. Its six new audiophile XDR Extended Dynamic Range mic preamps offer the best RFI rejection of any compact mixer design. Added benefits include maximum freedom from ground loops and impeccable sonic performance that meets or exceeds the specs of esoteric, outboard mic preamplifiers. The XDR design is the only compact mixer mic preamp that is totally impedance independent: frequency response does not change even with extremely long cable runs or exceptionally high-impedance mic inputs. A sharp, 8/octave 7Hz ow Cut filter on each mic channel greatly reduces mic thumps, wind noise and stage rumble. Mute/Alt - effectively creates a second stereo bus. The Mute button on each channel mutes that channel in the Main Mix, while simultaneously placing the signal on the Alt - stereo bus, greatly increasing signal routing flexibility. The to Monitor feature allows routing of reverb or other effects signals back into a monitor mix via Aux Send. Aux Master s Pre/Post switch can be set for pre-fader/post- use, which is beneficial for stage monitor mixes, or post-fader/post- for use with external effects. It also has a level control for added flexibility. Control Room/Phones has its own level control, stereo output pair and input matrix for selecting any combination of Main Mix, Tape In and Alt - to create custom headphone mixes, to monitor tape levels, and more. A separate switch routes this multi-source signal back into the Main Mix. Because of its many features and durability, the -VZ PRO can be used for extra studio-grade preamps, as aux inputs for a mixing console, or as an impedance- or level-matching audio toolkit. RM-VZ Rack-Mount Brackets (not included), 0-VZ PRO -Channel Mic/ine Mixer, -VZ PRO 6-Channel Mic/ine Mixer, 6-VZ PRO 6-Channel Mic/ine Mixer, SRM Active -Way SR oudspeakers, M 800/M 0i/M 0/M 0 Power Amplifiers, C0 passive -way SR oudspeakers -Channel Mic/ine Mixer Features 6 low noise/high headroom XDR (Extended Dynamic Range) XR mic inputs with the best RF rejection of any compact mixer design and maximum freedom from ground loops 6 balanced/unbalanced mono line inputs pairs of balanced/unbalanced stereo line inputs mm log-taper faders 8V global phantom power -band (khz,.khz, ) 7Hz, 8/octave ow Cut filter on Channels 6 PF/AF Solo (in-place) on all channels (global) Very ow Impedance (VZ) architecture to Monitor switch Alt - extra stereo bus Balanced inputs and outputs (except RCAs and channel inserts) Balanced XR Main /R outputs with mic/line level switch plus /" Main /R outputs Gain on Channels 6 Global Aux Pre/Post-Fader switch evel Setting ED and marker Applications ive sound mixing for churches, clubs, school auditoriums, school sports centers, hotel conference centers, boardrooms, trade shows, presentations Multitrack studio and field recording Headphone or cue mixer, impedance or level matching tool kit A/V presentations, video post production, CD authoring, multimedia ive broadcast remotes, ENG, ad production
Specifications Mic Preamp Equivalent Input Noise (0Hz 0kHz): 0Ω 0Ω 0Ω Frequency Response: 9.u.0u.u Hz 0kHz Hz 9kHz IM Distortion ( to ratio SMPTE) gain 0.0008% Harmonic Distortion (0Hz 0kHz) gain 0.0007% Gain Max Min Max Input Input Impedance Common Mode Rejection Common Mode Rejection Ratio Main Mix Noise Main Mix down, ch. faders down: Main Mix @ unity, ch. faders down: Main Mix fader @ unity, channel faders @ unity: + 0 or nity +.kω > 90 > 90. 90. 88. High Shelving: Mid Peaking: ow Shelving: Power Consumption Physical Weight Dimensions.9" (8mm) 8 rack spaces ±db @ khz ± @.khz ±db @ 0VAC, 0/Hz, Watts 9. lbs. (. kg) " x " x.9" (mm x 6mm x 7mm) " (6mm) Total Harmonic Distortion (THD) Attenuation (Crosstalk) Main fader down: Channel Alt -/Mute switch engaged: Channel fader down: 0.00% 8u 8u 8u Frequency Response Mic input to any output 0Hz to khz: 0Hz to 0kHz: Maximum evels Mic in: Tape in: All other inputs: Main Mix XR outputs: All other outputs: +0/ +0/ +u +6u +u +8u +u 9" (8mm) with RM-VZ Rackmount brackets " (6mm) Impedances Mic in:.kω Channel Insert return:.kω All other inputs: > kω." (mm) Tape out:.kω All other outputs: 0 ohms Specifications footnotes: ) 0Hz 0kHz bandwidth, /" Main out, channels 6 Trim @ unity gain, channel s flat, all channels assigned to Main Mix, channels, and Pan left,, and 6 Pan right. Reference +u. ) khz @ +u, 0Hz 0kHz. ) khz relative to 0u, 0Hz 0kHz bandwidth, ine in, " Main Out, Trim @ unity. ) Any input to any output. ) Mic in to Insert Send out, max gain..9" (7mm).9" (7mm)
MIC MIC MIC MIC EFT/ RIGHT /N MIC MIC 6 A /N TAPE TAPE INPT OTPT -VZPRO R R N INE IN INE IN -V CT 7 Hz 8/OCT -V N CT 7 Hz 8/OCT N INE IN INE IN -V CT 7 Hz 8/OCT -V N CT 7 Hz 8/OCT INE IN N CT 7 Hz 8/OCT -V INE IN 6 -V N CT 7 Hz 8/OCT STEREO AX RETRN N AX SEND N N MAIN OT R R R R N 0 - TRIM 0 - TRIM 0 0 0 0 - - - - TRIM TRIM TRIM TRIM EVE EVE EVE EVE + + + + - - - - INE IN 7 8 INE IN 9 INE IN INE IN PHONES AX khz AX khz AX khz AX khz AX khz AX khz AX khz AX khz AX khz AX khz - - - - - - - - - - - +.khz - +.khz - +.khz - +.khz - +.khz - +.khz - +.khz - +.khz - +.khz - +.khz - - - - - - - - - - MTE MTE MTE MTE 6 MTE MTE 7 8 9 MTE MTE MTE MTE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 + AX MASTER PRE POST AX SEECT C-R/SCE TO MONIT EFT +0 NMAED AX +0 RETRN RIGHT 0=0u 8 MAIN MIX 7 0 TAPE ASSIGN TO MAIN MIX 7 0 EVE SET PHANTOM MODE POWER NMA (AF) EVE SET (PF) RDE IGHT CTM /SBMIX MAIN MIX
OGIC PF AF AF AX POST AX POST AX PRE AT R AT MAIN R MAIN PHANTOM POWER (GO SWITCH) INSERT MIC IN MAIN MIX TRIM 7Hz HPF CT MAIN FADERS AT MIX TAPE IN R AF O AF 80 K K INE IN -BAND CHANNE ( OF 6) O FADER 80 K K INE IN () + /- O INE IN R 80 K K -BAND STEREO CHANNE ( OF ) PRE IN () AX RETRN R IN IN AX RETRN R IN MTE / AT FADER AF AF PF OGIC AX SEND POST PRE AX SEND MTE / AT AF AF PF AX SEND OGIC POST AX SEND GAIN GAIN TO MONIT AT TAPE MAIN PF MIX SIP ( IN PACE) / PF (PRE-FADER ISTEN) REAY PF ED ASSIGN TO MAIN AX OT AX OT PAD AT OT AT OT R SCE CONTROM & PHONES MIX CONTROM & PHONES FADER AX PRE / POST TAPE OT AX EVE INE OT OT AX MIX OT R INE OT R TAPE OT R +8 + +7 + + 0- - -7 - -0 - METERS Øu=Ø V RDE ED CONTROM EFT PHONES OT CONTROM RIGHT AX MIX
Architect s and Engineer s Specifications. GENERA CONFIGRATION. The mixer shall accommodate 6 microphone signals, mono channels 6; line signals, mono channels 6 and stereo channels 7 ; stereo pairs of Aux Return inputs; 6 Send/Return channel Inserts; stereo pairs of Main Mix outputs; stereo pair of Control Room outputs; stereo pairs of RCA-type phono Tape outputs and inputs; stereo pair of Alt - outputs; Aux Send outputs; and stereo headphone output. The mixer shall be capable of placement on a table or installation in a standard 9-inch rack mount (via optional rack rail brackets) and shall be entirely self-contained.. MIXER INPTS. CHANNES 6: The mixer shall include 6 XDR(tm) (Extended Dynamic Range) electronically balanced mic inputs, using XR--F-type connectors, accepting nominal levels from u to +u via 6 rotary Trim controls. Phantom power shall be available via a globally-controlled rockertype switch. 6 balanced or unbalanced (bal/unbal) line inputs shall be wired in parallel, using /" TRS phone jacks, accepting nominal levels from u to +u. The mixer shall include 6 channel Inserts, using /" TRS phone jacks (tip=send, ring=return, sleeve=ground), delivering and accepting nominal levels from V to +u. STEREO CHANNES 7/8, 9/, / and /: The mixer shall include 8 bal/unbal line inputs, forming stereo input pairs, using /" TRS phone jacks, accepting nominal levels from V to +u, with +u/ V level switches. OTHER INPTS: The mixer shall include bal/unbal Aux Return inputs, forming two stereo pairs, using /" TRS phone jacks, accepting nominal levels from V to +u. The mixer shall include stereo pair of Tape In jacks, using unbalanced RCA-type phono jacks, accepting nominal levels from 0V to +0u.. MIXER OTPTS. MAIN OTPTS: The mixer s Main Output stereo pairs shall be fitted in three ways: sing balanced XR--M-type connectors, delivering maximum output of +u, including Main Output evel switch to provide attenuation (XR outputs only; 6u nominal level); using bal/unbal /" TRS phone jacks, delivering nominal levels from V to +u; and using unbalanced RCA-type phono jacks (labeled TAPE OT), delivering nominal levels from V to +u. OTHER OTPTS: The mixer shall include stereo pair of Alt - outputs using bal/unbal /" TRS phone jacks, delivering maximum output of +u; stereo pair of Control Room outputs using bal/ unbal /" TRS phone jacks, delivering a maximum output of +u; Aux Send outputs using bal/ unbal /" TRS phone jacks, delivering nominal levels from V to +u; and stereo Headphone output using an unbalanced /" TRS phone jack (tip=left, ring=right, sleeve=ground).. MIXER INPT SECTION. In addition to the controls listed in section (MIXER INPTS), each channel shall include rotary Aux Send controls, providing up to gain; rotary equalization () controls: ± @ khz shelving, ± @.khz peaking and ± @ 80kHz shelving; rotary Pan control, attenuation panned center; Mute/Alt - switch, to be used as a channel mute or to route the signal to the alternate stereo bus (Alt -); dual-mode solo switch (AF or PF, globally switched); and channel fader, providing up to above unity gain.. MIXER OTPT SECTION. The mixer shall have Main Mix faders, providing up to gain; Control Room/Submix Fader, providing up to gain; Source Matrix including switches to deliver any combination of stereo signals to the Control Room, Phones and Meters, including Main Mix, Alt - and Tape, which shall be replaced by any solo signals resulting from the engagement of any channel s Solo switch; Assign to Main Mix switch to deliver the Source Matrix signals to the Main Mix; Solo Mode switch to globally determine solo type (pre-fader listen or after-fader listen, in place); rotary Aux Return level controls, providing up to 0 gain; rotary Aux Send Master control, providing up to gain; Aux Send global Pre/Post switch; to Monitor switch, allowing Aux Return signals to be delivered to Aux Send via the Aux Return level control; and blinking red Solo ED, to indicate a solo condition. 6. METERING. The mixer shall include stereo -segment ED meter with points at, 0,, 7,,, 0, +, +, +7, +, and +8 (clip). The source signals for the meters shall be the same signals selected in the Source Matrix, and a solo condition shall replace the Source selection with the
soloed channel(s). The meters shall be calibrated so that a 0u signal at the Control Room output shall be indicated as 0 on the meters, ± ED. 7. PHYSICA CONFIGRATION. The mixer shall be made of steel, painted dark gray with light gray graphics. The mixer s dimensions shall be.9" (7mm) in height,.0" (6mm) in width and.0" (mm) in depth, as viewed horizontally. The mixer shall weigh 9 lbs, 8 oz (. kg). Optional RM-VZ rack-mount brackets shall allow the mixer to be mounted in a rack system, with either the chassis top or the control knobs tops to be flush with the rack rail. 8. SPECIFICATIONS. In addition to specifications already cited, the mixer shall meet or exceed the following specifications: Frequency response: microphone input to any output, 0Hz to khz, +0/ ; Total Harmonic Distortion (THD): any input to any output, khz @ +u, 0.0007%; Equivalent Input Noise (EIN): microphone input to insert send, 9.u; Common Mode Rejection (CMR): microphone input to insert send, maximum gain, khz, better than 90; Typical Main Output noise: all channels assigned, channels, and panned left, channels, and 6 panned right, 86.u; Signal to Noise ratio: ref +u operating level, 90; Attenuation: ref. 0 @ khz, Main Mix level control down, 8u; Channel Mute engaged, 8u; Channel Gain control down, 8u; Input impedance: microphone inputs,. kω; Channel Insert return,. kω; All other inputs, greater than kω; Output impedance: Tape Out,. kω; All other outputs, 0Ω. The mixer shall be a Mackie Designs -VZ PRO. FIES F DOWNOADING VZP.PDF this specification sheet AE.TXT text version of Architect s and Engineer s Specifications for insertion into proposals Wood-Red Rd NE, Woodinville, WA, 9807 ph.87., fax.87.7, e-mail: sales@mackie.com, web: www.mackie.com K Blenhiem Ct., Hurricane Way, Wickford, Essex,SS 8YT, ph + 68 7, fax + 68 70809, e-mail: mackie.uk@rcf-uk.com FRANCE Rue de la Guerlande, 7880 Chatenoy-le-Royal, ph 0.8.6.9., fax 0.8.6.9., e-mail: rcf.commercial @wanadoo.fr ITAY Via G. Ferraris /A, 9 S. Maurizio (RE), ph +9.0., fax +9 0 87, e-mail: mackieitaly@rcf.it GERMANY Kuhlmannstrasse 7, 88 Emsdetten, ph +9.7. 9.0, fax Mackie Designs continually engages in research related to product improvement. New material, production methods, and design refinements are introduced into existing products without notice as a routine expression of that philosophy. For this reason, any current Mackie Industrial product may differ in some respect from its published description, but will always equal or exceed the original design specifications unless otherwise stated. 999 000 Mackie Designs Inc. All rights Reserved. The Mackie. logo and the Running Man figure are registered trademarks of Mackie Designs Inc. VZ, VZ PRO and XDR are trademarks of Mackie Designs Inc. Part No. 09-9-00.