PROJECT TYPE DATE QTY Outdoor Series LWW/LFL-W150A LWW/LFL-W150A-36P DESCRIPTION: The LWW/LFL-W150A LED Light Source is a multi-controllable and configurable wall washer for the architectural and commercial lighting markets. It can work in independent mode with built in programs for single steady color or DMX mode for various color and light changing effects or master/slave mode for automation and synchronization. (LFL is single color without DMX control) LWW/LFL-W150A-72P SPECIFICATIONS Materials Aluminum Alloy / 6063 Rotary Angle 150º Input Voltage Operating Voltage Rating Operating Temp. 120/240V AC 24V DC IP65-20º C 40º C LWW/LFL-W150A-144P PHOTOMETRICS (more on page 5) 13 / 25.19 / 48.81 330mm / 640mm / 1240mm 5.9 150mm 75 75 6.69 170mm MODEL NO. LED COLOR LED QTY. POWER BEAM ANGLE SIZE WEIGHT LWW/LFL-W150A-36P LWW/LFL-W150A-72P LWW/LFL-W150A-144P 36 72 144 40 Watts 90 Watts 170 Watts L13, W5.9, H6.7 L25.19, W5.9, H6.7 L48.8, W5.9, H6.7 11 lb 18.73 lb 33 lb V. 118 Copyright 2018, Impact Lighting Inc. All Rights Reserved
Modes: B1: Independent Mode: Choose the built-in program via the switches on the endcap B2: DMX Mode: International standard DMX512 signal (IP68 connector) B3: Master/Slave Mode: Automation and synchronization LWW/LFL-W150A INSTALLATION & Setup: B1 (Independent Mode) 1. Press the A button four times OR the B button once to enter independent mode. 2. Display will show PXY(for independent mode) 3. Press the A once to activate and begin selecting your desired X value. 4. Press A again to scroll through X value numbers (numbers scroll backward) 5. Press B to scroll through Y value LED display (numbers scroll backward) INDEPENDENT MODE: FUNCTION / PARAMETER CHART X Value = mode Y Value = brighness/speed X-Value Y-Value A B P 1 9 Mode Brightness/ Speed (Sample above shows Independent set at Static Red Mode at Maximum brightness) X-VALUE 1 = static red 2 = static green 3 = static yellow 4 = static blue 5 = static purple 6 = static cyan Y-VALUE X-VALUE 1 = static white 8 = multicolor change 9 = single color fade A = multicolor fade B = multicolor strobe C = autorun Y-VALUE 1-9 loop B2 (DMX Mode) 1. Press the A button three times to activate DMX mode 2. Wait until display stops flashing 3. Press the A to begin selecting your Channel 1 RED value. (numbers scroll backward) 4. Press B to begin selecting your Channel 2 GREEN value. (numbers scroll backward) 5. Press A to begin selecting your Channel 3 BLUE value.(numbers scroll backward) DMX MODE: FUNCTION / PARAMETER CHART CHANNEL 1 Red Brightness Value CHANNEL 2 Green Brightness Value CHANNEL 3 Blue Brightness Value Channel 1 A B 1 2 5 Channel 2 A B 2 0 0 Channel 3 A B 0 2 5 B3 (Master / Slave Mode) 1. Choose any 1 light as a master 2. Set the master address as 001 using the A button 3.Set the other lights at any other address except 001 A B 0 0 1
Connection: Maximum signal connection is 32 feet (10m). Over 32 feet need a signal amplifier. Optional controller options: EPIC Advanced RS232, Sunlite, DMX-192C, Madrix LWW/LFL-W150A INSTALLATION DMX Controller Signal Amplifier 1 2 60 61 62 120 Installation: Secure the brackets with M8 bolt. 1.8 46mm 3.14 80mm.78 20mm 0.3 8.2mm
LWW/LFL-W150A INSTALLATION Waterproof Treatment: The signal output connector of the last fixture of the last series MUST BE SEALED with a 20mm thermal shrinking tube. 1: Cover connectors with shrink tube 2: Use blowdryer to shrink tube 3. Wrapping ENTIRE TUBE with waterproof tape for sun protection. SHRINK TUBE WATERPROOF TAPE! * Power connectors should be treated in the same manner ** IP68 power connector does not require treatment, however a threaded twist should be waterprooedf treated to prevent operational errors due to joint water CAUTION: 1. Do not plug in light while product is still in package. 2. Do not cover fixture while powered on an lit. 3. Do not use this fixture in a closed environment. 4. If this product appears to be damaged, do not attempt to repair. Call the manufacturer. WARNING: * Neglect in waterproofing connectors and threaded twists with the above instructions will led to product failure! * Make sure ground connection is sound to avoid electrical shock due to metal housing. * Do NOT CUT the updated IP68 connectors as it will void warranty and will not be replaced by the manufacturer.
LWW/LFL-W150A INSTALLATION Phtometrics: