BMW CIC Video Interface For 2010 UP With CIC system Round LVDS connector Main Features: 1. It is suitable for all 2010 up version Round connector LVDS CIC monitor system. 2. It is for BMW, 1, 3, 5, X5, X6, Z4, and 7 series with I drive system. 3. With 2AV input, RGBS input, Rear camera input, LVDS input 4. With 1AV output, LVDS output SYNCH 5. Built in CANBUS by original button MENU I drive system Switch functions. Auto Rear camera Activation completely when gear is in reverse position, no need to connect rear light +12V 6. With touch operation system for external DVD, DVB T, GPS NAVI. you can by touch screen to control DVD, DVB T, GPSBOX after by learing IR code command, this is excellent for add after market video unit. 7. With completely plug and play to finish the installation, no need to cut, and weld any cable to finish the installation 8. It is with 16:9 and 24:9 showing solution by press OPTION to switch 9. With resolution: 480*234, and 800*480, and 1246*480, by Switcher to change these resolution. 10. If you do not want to add the external touch screen in front of the original monitor, you can also use the original MENU I drive button to control the DVD, DVB T, or GPS by learing remote IR command code. 11. Built in GPS function (Optional) 12. Switch by original NAV button or by Toggle switcher. 13. Use original monitor connector to instal the video interface, which to make the installation as much easy as possible to save the instalation time greatly, and to protect the original system.
Video Interface connection: 1.The Can and Power connector is plug and plug to the original Monitor, and the Radio. and not need to cut any cable, then to finish the all installation. 2.And also the Rear camera is also activated by the CAN built-in the video interface, so also there is no need to cut to connect the external 12V cable to rear light +12V, then can activate the rear camera auto when gear is in reverse position, this is 100% plug, and plug, and play, which to save the installation time greatly, and also will avoild to damage the car original system. Operation: Press MENU button: NAVI, or MAP will be switched into: RGB AV1 AV2 Radio MENU Press CD: Go back to CD MENU Press Radio: Gp back to Radio MENU Press Option: to Switch 16:9 and 24:9 in the monitor picture show format. 2 / 6
1 RGB video amplitude 0.7Vpp with 75 ohm impedance 2 sync amplitude in RGB navi port 3~5Vpp with 5K ohm impedance Sync should be NTSC composite with negative polarity. When in VGA mode, the Hsync and Vsync should be combined by a 74HC86 to make a Composite sync.[xor operation], it can be XOR with 1 to get inverted to negative polarity. 3 RGB resolution NTSC RGB navigation, that is. 320X240,400X240,480X240 Or VGA resolution[640x480 or 800X480] 4 Av1,Av2, cam video 0.7Vpp with 75 ohm impedance NTSC/PAL/SECAM automatic switch 5 IR RGB, IR_AV1 output 3.3V digital infrared control code with 4 data bytes [machine code1,machine code 2, user code, verification code] 6 Normal Power consumption 2.4W [0.2A @12V] 7 Standby current < 10uA 8 Reverse trigger threshold >5V trigger 9 Ctrl port Pin1,2 and Pin7: Output voltage Relay pull voltage for Audio and touch screen selection 5V volts. 10 Ctrl port Pin1,2 and Pin7: Current 2A. Tested to have no damage when short circuit to GND for 2 minutes. Leave it open when do not use. 11 Work temperature 40 ~ +85C
At present, BMW CIC, VOLVO, BENZ 2011 NTG4.5, AUDI 3G MMI, Benz S class, Ford viode interface, etc you can only directly to connect this RGBS cable to be as the above instruction, then can realize external DVD, DVB T, GPS BOX by touch operation after by learning IR touch Code Command! IR cable connection: Please look at the above picture, IR cable is for external DVD, DVB T IR cable input connection. In common, you need to cut the DVD, and DVB T IR remote cable IR receiver head, then you can see there are three parts in this DVD IR cable: two small cable, and one is the shielding case. Among the two small cable, the cable connecting to the first leg of IR head receiver is the IR signal transmittion, the other small cable is useless, so you only need to connect the IR transmitton cable the video interface IR output cable together is ok. Please look at the right picture, the RED CIRCLE marked is the Fisrt Leg of IR header, to connect the DVD, or DVB T IR cable, and the DVD, DVB T IR cable shielding case connecto to be Ground after cut the IR header. Then to finish the video interface and external DVD, DVB T IR cable connection.
To set the video interface switcher 6 th PIN to down for ready IR code learing as the picture: Then the original screen will show the touch ICON for ready learning IR CODE COMMOND as the below picture: Finally, to make the DVD, or DVB T remote contorller point at the video interface IR eye as the below picture show ( the IR eye is inside the video interface) to start the IR command learning
correspondly, you must do not exit this learning situation unit to finish the all touch ICON IR command learning, otherwise, the learning will be failed. after finish all the touch ICON learning then to pull up and down video interface switch 6 th PINS 5-6 times to calibration, until the monitor appear the Cross LOGO, then stop to pull the DIP6, and start to touch the CROSS LOGO to calibration touch functions. See the below Pictures: After calibration, you can touch the monitor to operate the DVD, or DVB T by these touch ICON