The Data Scout 1G (DS-1G) is a non-modular hand held combining seven different physical layer test protocols into a single easy to use solution allowing field technicians to quickly provision and assure multiple data services. KEY PRODUCT BENEFITS: Fast Less than 15 seconds from power up to ready for testing Easy to use touch screen interface Light weight, yet rugged Designed for field technicians installing mobile backhaul and business services KEY PRODUCT SPECIFICATIONS: 10/100/1000BaseT and 100/1000BaseX interfaces RFC-2544 and Y.1564 performance tests with graphing and reports Synch-E and Y.1588 network synchronization test options (Target Release Q3-14) T1/E1 test option T3/E3 test option CODIR and DATACOM test options C37.94 SCADA teleprotection testing for utilities VoIP, IPTV and Wi-Fi testing options Basic Ethernet cable diagnostics Supports USB fiberscope to inspect connector face Future support for USB optical power meter Management port with VNC remote access Padded soft carrying case included Optional hard case Optional padded jacket
BASIC ETHERNET (DS1G-SW-BAS) Interfaces: Electrical 10/100/1000 Base-T Optical SFP: 1000-Base-X IP Version: IPv4 (future IPv6 software upgrade) BERT Streams: 1 Test Modes: Single: Point to Point Layers: 1 (Unframed/Framed), 2 Patterns: All Zeros, All Ones, 1:1,1:3, 2:2,5:32, 2e15,2e20,2e23, 2e31, User Defined, Invert Frame size: 64, 128, 256, 512, 1024, 1536 Error Injection: Code, Bit, CRC, Single, Rate BERT RESULTS Measurement Counters: Start time Test duration Line rate Data rate: Current, Min, Max Frame: Average Frames per second: Current, Min, Max Bits Count Bytes Count Error Counters: Average Rx Errors: Current, Total Error Types: Bit, BER, Code, CRC, CRC, Sequence Histogram of any error type Alarm Counters: LOS, Link Down/time, Sync/time Service Disruption: Last, Min, Max, Average, Total, Time RFC 2544 Layers: 2-4 Tests: Throughout Latency Frame Loss Back to Back (burst) Mode: Bidirectional Local to remote Remote to local RFC2544 RESULTS Throughput: Frame size, Throughput %, Status Latency: Frame size, Rate %, Latency us, Status Frame Loss: Frame size, Frame Loss%, Status Burst: Frame size, Frame count, Status Graphical report generation for all results LOOPBACK Manual: Layer 1, 2, 3 WIREMAP Tests for: Opens, shorts, crosstalk, length, impedance ADVANCED ETHERNET (DS1G-SW-ADV) Includes all DS1G-SW-BAS test functions MULTI-STREAM BERT Streams: Up to 8 Layers: 1-4 802.1Q (Q in Q): Up to 2 tags Configurable VLAN tag Configurable 802.1P priority MPLS: Up to 2 tags IP Header Configuration: ToS, TTL, Protocol, Frame Offset User defined frame sizes: 48 to 12,000 Y.1564 SERVICE ACTIVATION TEST Services: Up to 8 Layers: 1-4 Test Modes: Configuration, Performance SLA Criteria: CIR, EIR, FTD, FDV, FL, Availability, Color Mode Service Configuration Metrics: CIR, EIR, FTD, FDV, FLR pass/fail Utilized Line Rate: Tx/Rx Frame Count: Tx/Rx Frame Loss Frame Loss Rate Service Performance Metrics CIR, EIR, FTD, FDV, FLR pass/fail Availability/Unavailable seconds Alarm Counters: LOS, Link Down/time, CRC Graphical report generation for all results RFC-2544 Test Modes: Single: Point to Point Dual: Local to Remote & Remote to Local Simultaneous: Back to Back 802.1Q (Q in Q): Up to 2 tags Configurable VLAN tag Configurable 802.1P priority MPLS: Up to 2 tags User defined frame sizes: 48 to 12,000 LOOPBACK Manual or Automatic: Layer 1, 2, 3
Y.1588v2 Test Suite (NP1G-SW-1588) Target Release Q4-14 Requires NP1G-SW-ADV Packet Delay Variation (PDV) Round Trip Delay (RTD) Inter Packet Gap (IPG) Asymmetrical Variation PTP message capture and decode Frequency Measurement RESULTS Event Messages: Synch Delay Request Delay Request/Response (measures link delay between two clock ports) General Messages Announce, Follow Up, Delay Response, Pdelay Response Follow Up, Management Signaling Message Statistics: Event, General, CRC error, Loss, Duplicate, Out of Order, Unidentified SynchE Test Suite (NP1G-SW-SYNCE) Target Release Q4-14 Requires NP1G-SW-ADV Wander measurement of recovered clock Wi-Fi Test Suite (NP1G-SW-WIFI) Radio Interface: 802.11b,g,n and Bluetooth Access Point Detection Count: All detected Information: SSID, AP Name, Network Type, MAC, IP, Rx Power, Security, Encryption Connection: Authentication: WEP, WPA, WPA2 Encryption: Client Location PING RESULTS Connection Status IP Information: Address, Net mask, Gateway IPTV Test Suite (NP1G-SW-IPTV) Streams: Up to 30Mbps (5-6 SD or 1-2 HD) Modes: STB Emulation Stream Emulation Video on Demand Testing Signaling: RTSP, IGMP CODEC: H.264, MPEG-2, MPEG-4, VC-1 Channel Zapping Channel Scan RESULTS PID Information: Number Type: PAT, PMT, Audio, Video Bandwidth Stream Information: Multicast/Unicast address Data type (stream/pid) Bit Rate IP source & destination address UDP source & destination address Packet Statistics: Loss Out of sequence Discarded Received ratio TR101290 Priority 1 Messages: TS Sync Loss, Sync Byte Error, PAT Error, PAT 2 Error, Continuity Error, PMT Error, PMT 2 Error, PID Error Priority 2 Messages: Transport Error, CRC Error, PCR Error, PCR Repetition Error, PCR Discontinuity Error, PCR Accuracy Error, PTS Error, CAT Error VoIP Test Suite (NP1G-SW-VOIP) Modes: Originate and receive live voice calls Signaling Protocol: SIP CODEC ITU-T G.711 u-law ITU-T G.711 A-Law RESULTS Call Progress Call Log
E1 INTERFACE (DS1G-SW-E1) Available on DS1G-PDH1/PDH2 Analyzers Only E1 RECEIVER: Input Frequency: 2,048,000 Hz +/-300 ppm Sensitivity: Terminate: +3 to -39 db-dsx Bridged: 0 to -30 db-dsx DSX: 0 to -26 db (resistive loss from nominal DSX level) Input Jitter Tolerance: Exceeds CCITT G.823 E1 TRANSMITTER: Impedance: 120 or 75 Ohms software switchable Interface: BNC and RJ-48 Output Level: 0+/-0.5 db-dsx Output Clock: Internal oscillator 2,048 khz+/- 5 ppm External, 3000 Ohm TTL, SMA Input Clock: Recovered from input signal E1 : Impedance: 120 or 75 Ohm Connectors: Bantam and RJ-45 2048 Kbps E1 Interface: Per CCITT G.703, G.704 Input/Output Connectors: Bantam, RJ-45 Framing Modes: Auto, Unframed, CAS, CCS, CAS+CRC4, CCS, CRC4 Line Coding: HDB3, AMI PCM Companding Law: µ or A Alarm and Status soft LED's with history: Signal and Loss of Signal Frame Sync Loss of Frame Alarms: LOS, OOF, AIS, RAI, MFAIS, MFRAI Errors Pattern Synchronization E1 AUTO MONITOR: Line: Code Error- bipolar violation of HDB3 or AMI Frequency: Range: 1.8-2.2 KHz Resolution: 1Hz Accuracy: 5 ppm standard Signal Level: +3 to -40 db-dsx (0.06 to 8.5 Vpp) Clock Slips: +/- between internal or external E1 clock Frame Slips: Clock slips/256 Alarms: LOS, OOF, AIS, RAI, MFAIS, MFRAI Errors: Code, Frame, CRC, FEBE, G.826: ES, SES, ES RATIO, SES RATIO, AVS, UAVS RFC 1406: Total Seconds, ES, SES, AVS, UAVS M.2100: ES, SES, UAVS E1 BERT (BIT ERROR TEST) FUNCTIONS: Standards: ITU-T G.703, G.704 E1 Test Patterns: 2n-1, n =7: 9:10:15:20:23, QRSS, All Zeros, All Ones, 1:3, 1:7, 1:15, 1:31, Multi-pattern, Bridge Tap, Inverted Error Measurements: Logic Errors, Rate, ERS, BPV Errors, Rate, ERS Frame Errors, Rate, ERS CRC Errors, Rate, ERS E-bit Errors G.821: EFS, ERS, SES, AVS, UAVS Error Injection Types: Logic, BPV, Code, Frame, CRC Error Injection Methods: Single, Continuous, Rate 10-1 to 10-9 Alarm Generation: LOS, OOF, AIS, RDI Alarm Monitoring: LOS, OOF, AIS, RAI Loopbacks: Remote through mode for line code and errors transparency Local Loopback FRACTIONAL E1: Fractional Nx56/64 kb, n=1-31 channel access for Auto Monitor or BERT tests E1 PULSE SHAPE ANALYSIS: Analyzes E1pulse shape using G.703 mask Displays or prints screen of the plot PROPAGATION DELAY (ROUND TRIP) Range: 0-2 sec Resolution: 1 msec CO-DIR (DS1G-SW-CODIR) Requires DS1G-SW-E1 Standard: G.703 Co-dir 64 kb/s Connector: Bantam Impedance: 100 Ohms
T1 INTERFACE (DS1G-SW-T1) Available on DS1G-PDH1/PDH2 Analyzers Only T1 RECEIVER: Input Frequency: 1,5444,000 Hz +/-300 ppm Sensitivity: Terminate: 3 to -34 db-dsx Bridged: 0 to -30 db-dsx DSX: 0 to -26 db (resistive loss from nominal DSX level) Input Jitter Tolerance: Exceeds CCITT G.823 T1 TRANSMITTER: Impedance: 100 Ohms software switchable Interface: BNC and RJ-48 Output Level: 0+/-0.5 db-dsx, 6 Vpp Output Clock: Internal oscillator 1,544 khz+/- 5 ppm External, 3000 Ohm TTL, SMA Input Clock: Recovered from input signal T1 : Impedance: 100 or 75 Ohm Connectors: BANTAM and RJ-45 DS1 (T1 Interface): Per CCITT G.703, G.704 Framing Modes: Auto, Unframed, ESF, D4, SFS, SF-N, SLC-96 Line Coding: B8ZS, AMI PCM Companding Law: µ or A Alarm and Status soft LED's with history: Signal and Loss of Signal Frame Sync Loss of Frame Alarms: LOS, OOF, AIS, RAI, RDI Errors Pattern Synchronization T1 AUTO MONITOR: Line: Code Error- bipolar violation of B8ZS or AMI Frequency: Range: 1.8-2.2 KHz Resolution: 1Hz Accuracy: 5 ppm standard Signal Level: +3 to -34 dbdsx (0.06 to 8.5 Vpp) Clock Slips: +/- between internal or external T1 clock Frame Slips: clock slips/193 Alarms: LOS, OOF, AIS, Yellow Errors: Code, Frame, CRC G.826: ES, SES, ES RATIO, SES RATIO, AVS, UAVS, RFC 1406: Total Seconds, ES, SES, AVS, UAVS T1 BERT (BIT ERROR TEST) FUNCTIONS: Standard: CB-119 Test Patterns: 2n-1, n =7:9:10:15:20:23, QRSS, All Zeros, All Ones, 1:3, 1:7, 1:15, 1:31, Multi-pattern, Bridge Tap, Inverted Error Measurements: Logic, Errors, Rate, ERS, BPV Errors & Rate, ERS Frame Errors & Rate, ERS CRC Errors & Rate, ERS G.821: EFS, ERS, SES, AVS, UAVS Error Injection Types: Logic, BPV (Code), Frame, CRC Error Injection Methods: Single, Continuous, Rate 10-1 to 10-9 Alarms Generation: LOS, OOF, AIS, RDI Alarm Monitoring: LOS, OOF, AIS, RAI Loopbacks: Remote through mode for line code and errors transparency Local Loopback FRACTIONAL T1: Fractional Nx 56/64 kb, n=1-24 channel access for Auto Monitor or BERT tests T1 PULSE SHAPE ANALYSIS: Analyzes T1pulse shape using CB.119 mask Displays or prints screen of the plot PROPAGATION DELAY (ROUND TRIP) Range: 0-2 sec Resolution: 1 msec DATACOM (DS1G-SW-DCOM) Requires DS1G-SW-T1 : Interfaces: V.24/RS-232, V.35, RS-530 Connector: Hirose ST60-36 pin connector (sold separately) Data Rates: nx56-64 kbps n=1 to 24 (32) Variable frequency synthesizer 300 Hz 8 Mhz RS-232: 300bps to 115kbps V.35, V.36, RS-530: 300bps to 8 Mbps BERT: Patterns: 2n-1, n =7:9:10:15:20:23, QRSS, All Zeros, All Ones, 1:3, 1:7, 1:15,1:31, Multi-pattern, Bridge Tap, Inverted Error Measurements: Logic Errors & rate, ERS & rate, ES & rate, Pattern Loss, Character errors
E3 INTERFACE (DS1G-SW-E3) Available on DS1G-PDH2 Analyzer Only Interface: BNC Impedance: 75 Ohms E3 RECEIVER Input Frequency: 17.184 MHz +/-300 ppm Sensitivity: -33dB or 1200 feet (360m) of cable -35 db signal level to declare Loss of Signal -15 db signal Level to clear loss of signal Input Jitter Tolerance: Exceeds CCITT G.823 E3 TRANSMITTER Output Pulse: Conforms to ITU G.703 Nominal 0.8 Vpk (+/- 5%) External Clock Input: 75 Ohms, BNC connector Frequency Range: Input: 34,380 Mbps +/-500 ppm Output: 34.380Mbps +/- 5 ppm standard Transmit clock: Internal: 5ppm External: TTL Recovered E3 Framing Modes: Auto, Unframed, ITU-T G.751 Line Coding: HDB3 Clock Source: Internal, Loop Alarm and Status soft LED's with history: Signal and Loss of Signal Frame Sync Loss of Frame Pattern Synchronization Loss of Power Status: Low Battery Voltage Flashes on LCD screen when 5 minutes or less of charge remains BERT: Patterns: n =15:20:23, QRSS, All Zeros, All Ones, 1100, 1111, 0000, 32 bit user defined Measurements: Logic Errors & Rate, Frame Errors & Rate, Bipolar Violations & Rate, Summary Errored Seconds, Summary Error Free Seconds Error Injection: Type: Logic, BPV, Frame Method: Rate, Continuous, Single Loop backs: Remote Loopback, Local Loopback, Through Mode Output (same as remote loopback, allows signals and errors pass through) Send Alarms: AIS, RAI, LOS, LOF T3 INTERFACE (DS1G-SW-T3) Available on DS1G-PDH2 Analyzer Only Interface: BNC Impedance: 75 Ohms T3 RECEIVER Sensitivity: HIGH: +6dB to - 20 db from nominal HIGH level DSX: 0 to 26 db resistive loss or 6 db cable loss from nominal DSX level LOW: 0 to 20 db resistive loss or 6 db cable loss from nominal LOW level Jitter Tolerance: Exceeds TR-TSY 000499 category II equipment requirements T3 TRANSMITTER Output Pulse: Conforms to ITU G.703 & ANSI T.102 HIGH: Nominal 1.2 Vpk DSX: Nominal 0.6 Vpk LOW: Nominal 0.3 Vpk, equivalent of DSX level with 450' cable loss External Clock Input: 75 Ohms, BNC connector Frequency Range: Input: 44.736 +/-500 ppm Output: 44.736+/- 5 ppm standard T3 Framing Modes: Auto, Unframed, Framed M13 & C-bit Line Coding: B3ZS Alarm and Status soft LED's with history: Signal and Loss of Signal Frame Sync Loss of Frame Pattern Synchronization Loss of Power Status: Low Battery Voltage Flashes on LCD screen when 5 minutes or less of charge remains BERT: Patterns: n =15:20:23, QRSS, All Zeros, All Ones, 1100, 1111, 0000, 32 bit user defined Measurements: Logic Errors & Rate, Frame Errors & Rate, Bipolar Violations & Rate, Parity Errors & Rate, C-bit Errors & Rate, Far End Block Errors (FEBE) & Rate, Summary Errored Seconds, Summary Error Free Seconds Error Injection: Type: Logic, BPV, Frame, Parity, C-bit, FEBE Method: Rate, Continuous, Single, Burst Loop backs: Remote Loopback, Local Loopback, Through Mode Output (same as remote loopback, allows signals and errors pass through) Send Alarms: AIS, RAI, LOS, LOF
C37.94 Test Suite (NP1G-SW-C37) Optical Connector: SFP Optical Transmitter: Wavelength: 850 nm Output Power: -13 dbm Distance: 2 to 4 km Optical Receiver: Max input power: -3dBm Minimum input power: - 32 dbm Loss of Signal Asserted: -45 dbm Loss of Signal-Deasserted:-30 dbm Test Data Rate: 2Mbps, Nx64 kbps, n= 1-12 Transmission Bit Rate: 2,048 kbps Test Patterns: 2n-1, n=7-23, QRSS, All Zeros, All Ones, 1:3:7:15:31 Error Injection: Single, Continuous Rate 10-1 thru 9 Transmitter Clock: Internal, 3ppm or Recovered MEASUREMENTS Bit Errors Bit Error Rate ITU-T G.821 Analysis Alarms: LOS, Yellow Data Frequency Propagation Delay Optical Power in dbm Histograms for all STANDARD ETHERNET Activated on all DS1G Analyzers PING & TRACE ROUTE Type: URL or IP address Results: Data Size, TTL, Delay, Timeout, Attempts NETWORK DISCOVERY (ARP) Input: IP address/prefix Results: Total devices responding MAC & IP address of each FTP/HTTP TEST Input: IP/URL + file name Results: Throughput Current and Average Data transfer rate Transfer Time STANDARD FEATURES Included on all DS1G Analyzers INTERFACES Management: LAN 10/100 Base-T USB: Mini-USB with adapter Headset: mini USB connector ear bud Wi-Fi: 802.11 b/g/n Bluetooth Used for IP access only Performing tests requires NP1G-SW-WIFI DISPLAY & INPUT Display 3.5 TFT touch screen LCD 320x240 resolution Direction Keys 5-way keypad: up, down, left, right, OK/power button RECORD STORAGE Internal: 4GB flash External: USB flash Format: SQL Dbase Detail Levels: Summary Log of all tests Details per test Histogram of selected record Output: Display, Export to USB, Print to serial printer REMOTE CONTROL VNC server installed Accessible via management port or Wi-Fi WEIGHT & DIMENSIONS Dimensions: 100 x 210 x 42 millimeters (WxHxD) 3.94 x 8.27 x 1.66 inches (WxHxD) Weight: 0.75 kg (1.65lbs) without battery 1.00 kg (2.2lbs) battery installed ENVIRONMENTAL Operating Temperature: 0 Cto 50 C Operating Humidity: 5% to 90% non condensing Storage: -10 C to 70 C Battery: Type: Li Ion battery pack, 7.4V, 4800mAh Run Time: 7-10 hours typical (varies by test mode) External Power: Mains: 110-240 VAC, 50-60 Hz Enclosure: Ruggedized ABS with rubber shell
DISCLAIMER This specification is subject to change without notice. Errors and omissions excepted. CONFIDENTIALITY The information contained in this Technical Specification is the confidential, proprietary information of Greenlee Textron Inc. and, in addition to any restrictions that may apply pursuant to the terms of any Confidentiality or Non-Disclosure Agreement between Greenlee and the recipient (or the recipient's employer), is not to be copied, disclosed or distributed in whole or in part to any third party or used by the recipient in any manner other than the intended purpose for which it was provided to the recipient, without the prior written approval of Greenlee Textron Inc. Do not read this Specification if you are not the intended recipient. If you are not the intended recipient, or the person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution, or use of any of the information contained in or attached to this transmission is STRICTLY PROHIBITED. If you have received this specification in error, please immediately notify Greenlee and destroy the original specification without reading or saving in any manner.