P.01 Outperform. Outlast. YACHT AIRCRAFT HOTEL
P.02 CONTENTS Outperform. Outlast. C.01 INTRODUCTION C.02 FEATURES C.03 PRODUCT DIMENSIONS C.04 INITIAL PRODUCT SET-UP Set-up P.06 Images P.07 - P.08 Electric connector P.09 C.05 PRODUCT INTEGRATION Product Integration / Covering P.10 Sample images P.11 - P.13 Complete covering P.14 C.06 PRODUCT CONTROL Programming the remote control (S435) P.15 Resetting the receiver P.16 Connection to a room control system P.16 C.07 TROUBLE SHOOTING C.08 LEGAL NOTICE
C.01: P.03 INTRODUCTION Outperform. Outlast. Intended Use The product swivels out of LCD and plasma TV equipment. All company names and product names are trademarks of the corresponding owner. All rights reserved. The scope of supply can vary depending on the product and the range of fixtures and fittings. Please check that the product supplied is complete and inform us within seven days of delivery if the scope of supply is not complete. Safety and Hazards Recommendations Please read this chapter carefully and follow all of the instructions provided. In this way you are able to guarantee the reliable operation and a long lifespan for your lift system. Keep the operating manual in a safe place. In the event of damage which is the result of non compliance with this operating manual, all claims pertaining to the guarantee are null and void. We generally accept no responsibility for secondary damage. We accept no responsibility for damage to objects or persons which is caused by the inappropriate use of the product or through ignoring the safety instructions. In such cases, all claims pertaining to the guarantee are null and void. For safety reasons, the unauthorized conversion and/or changing of the product is not permitted. Do not dismantle this product. This product is not a toy and does not belong in the hands of children. Do not allow the product to become damp or wet. Do not leave the packaging material lying around as children may choke if they swallow it. The product will be damaged if it is dropped, even from a low height. Before using the product for the first time, please check that the free raising and lowering of the Flatlift including the mounted TV equipment is possible and ensure a collision-free run. For legal reasons and insurance purposes, your Flatlift is equipped with an automatic safety device. This means that the button which controls the raising and lowering must be pressed down all the time. The system stops and remains in the same position as soon as you let go of the button. Quality In the choice of our components, our primary focus was on ensuring a high level of functionality, straightforward use, safety and reliability. We would like to thank you for the trust you have placed in our Flatlift brand products. We can help you with your installation through providing individual customer care.
5 years full service Outperform. Outlast. C.02: P.04 PRODUCT FEATURES FEATURES Features: Installion dimensions Flatlift W=1645mm D=1050mm H=200mm opening rate 1,2 /sek Angle of aperture 95 Max. TV weight incl. cover 160Kg Max. TV size 50 (inch) (max. TV size in mm: W=1345mm, H=800mm, D=160mm) Power-on time 15%/h Low noise level < 45 db Environmental temperature from +5 C bis 40 C 4x flexible adjustable assambly brackets Remote control 433,63MHz Connection to room control system possible TV switch-off if closed BUY NOW Scope of supply: Flatlift Slimline 50 Control box 24V power supply unit Remote control LIFETIME Repaircost limit GUARANTY
C.03: P.05 PRODUCT DIMENSIONS DIMENSIONS Schnitt Cut a-a a-a 1200 1645 a a 200 920 1050 920 1050
C.04: P.06 INITIAL PRODUCT SET UP Outperform. Outlast. Initial setting / installation 1. Unpack your Slimline Plasma ceiling TV lift and place the Slimline on a level surface. 2. Align the 4 ceiling mounting brackets with the section as shown on page 07, image 1, No. 2 in a way that these fit your project optimally. You can displace the mounting brackets simply as you wish until these have reached the ideal position. Afterwards, please screw the brackets to the section by means of the screws provided (DIN 912 M8, SW6) using an Allen wrench. 3. Now, transfer the dimension of the hole centre distance of the mounting brackets to your prepared ceiling recess (S.07, image 1, No. 1). Use a drill (d = 8mm) to drill into your ceiling material. In case the Slimline ceiling lift is to be installed on a yacht with metal/aluminium ceiling, we recommend drilling a hole having the size suitable for a screw M8 (recommended drill/core hole diameter = 6.8mm). In case of concrete ceiling installation please use mounting anchors approved for being used with cracked respectively non-cracked concrete. We recommend using mounting anchors of the company Fischer. In case the installation is implemented with a wooden ceiling, you may install the Slimline lift to the wooden ceiling using wood screws (DIN 512, d = 8mm). The anchor respectively screw length should be at least 80mm for concrete or wooden ceiling installations. 4. Please attach your Slimline to the ceiling using the 4 mounting brackets (page 07, image 1, No. 1). 5. Now, align the 2 vertical supports in the Slimline flap with the VESA attachment dimension of your plasma / LCD TV, as shown in figure 2. In order to be able to move the supports, you have to loosen the DIN 912 screws using an Allen wrench (page 08, image 2, No. 3, SW 4). In doing so, the supports can be displaced horizontally to the dimension of the hole centre distance of the TV correspondingly. Once you have reached to desired distance, retighten the screws. Now, you transfer the hole centre distance from the X axis to the Slimline flap. Please observe that the holes of the X axis have been transferred to the section in a centred manner. 6. Now, you can transfer the coordinates of the Y axis of the TV mounting holes to the Slimline flap. During this step you will have the opportunity to align the TV upwards or downwards as the customer desires. 7. After you transferred all hole coordinates to the Slimline flap, you can centre punch the same now and drill the holes using a drill corresponding to the size of the screws (see page 08, image 3, No. 4). As there is no applicable standard for these mounting screws, we are not able to recommend an exact drilling diameter. The screws for wall-mounted TV sets may vary between M6 and M10 in dependency on the TV model. Please consult the Flatlift distribution department prior to ordering the product respectively procure the suitable screws with the local screw dealer.
C.04: P.07 INITIAL PRODUKT PRODUKT SET UP SET U Image 1 2 1
C.04: P.08 INITIAL PRODUCT PRODUKT SET UP SET U Image 2 Image 3 3 4
C.04: P.09 INITIAL PRODUKT PRODUKT SET UP SET U Image 4 Image 5 Image 6 5 8 6 7 9 10 Minus (-) (+) Plus Electrical connection: 1.Connect the motors to the control box (image 4, No. 5). Now, you may connect the motors to the control box. There is no connection sequence to be observed. 2. Connect the limit switch to the control box (image 5, No. 6). 3. Connect the 24V mains adaptor (image 6, No. 7) to the control box (image 5, No. 8). Please observe the polarity (image 6, No. 7). 4. Connect the control box (image 4, No. 9) and the 24V mains adaptor (image 6, No. 10) to the mains supply. 5. Now, please store the control box and the mains adaptor in the suspended ceiling or in a free area of the Slimline. Please consider planning a revision recess (see chapter 5, page 10). 6. Open and close your Flatllift Slimline once without the TV. In doing so, please observe a free pivoting area, so that the Flatlift Slimline does not make contact with any obstructions. 7. Due to insurance purposes, your Flatlift Slimline is equipped with an automatic safety device. This means that the button for opening and closing the system has to be pressed permanently. As soon as the button is no longer pressed, the Slimline system stops.
C.05: P.010 PRODUCT INTEGRATION INTEGRATION Product integration / cover flap lining: The Slimline cover flap may be lined in different variations. It is important to design a revision aperture allowing you to enter into the interior or the Slimline ceiling lift in case the Slimline has a failure. This section is to explain how the flap can be lined best. 1. Page 11, image 2, No. 1. Here, the flap of the Slimline ceiling lift is lined with the help of a 12mm MDF board. In this example our integrator used the product Scotch 3M Dual Lock. Scotch 3M Dual Lock is a high performance adhesive tape (similar to hook-and-loop adhesive tape). The design of this adhesive tape allows for very high holding forces. For this, please attach the 3M tape to the Slimline flap over a large area. Please observe that the flap of the Slimline lift has to be closed while attaching the tape. After having attached the adhesive tape to the flap, please remove the adhesive film and press the cover flap lining against the Slimline flap from the bottom. Please observe that the flap has to be aligned with the ceiling recess in order to obtain a uniform image. 2. Page 12, image 3. Here, the cover lining is screwed directly to the Slimline flap. In the grooves of the aluminium section there are 4 sliding blocks with holes of d = M6, suitable for counter-sunk screws DIN 7991. Depending on the design of the ceiling you may fill respectively cover these DIN 7991 counter-sunk screws with the actual ceiling lining material, so that the same are no longer visible. According to our experience this is one of the most commonly used lining variant, which furthermore may be implemented very easily. 3. On page 12, image 4 the cover lining is directly screwed through the flap of the Slimline TV lift. For this, align the cover plate accordingly and drill 4-8 times directly through the centre of the aluminium section, as shown on page 12, figure 4, No. 2. Afterwards, you can attach the cover plate using screws of an appropriate length. (In our case study we use 12mm MDF wood. Thus, in accordance with the thickness of the aluminium section (40mm) we use at least 45-50mm long wooden Spax screws in order to obtain a corresponding attachment stability. 4. On page 13, image 5, No. 3 you see how the flap solution is implemented at the rear end of the Slimline. The cover plate should project over the pivot axle of the flap by approximately 100-150mm and should be equipped with a mitre of approximately 45 at the end. The room ceiling lining in the recess area for the Slimline should be mitred with 45 as well. Thus, the cover flap can pivot freely at a minimum clearance. Furthermore, this solution has the advantage of the view into the rear part of the Slimline lift being prevented in case the Slimline is pivoted to the full extent. 5. You are free to encase your Slimline to a further extent, such as the Slimline flap with TV integrati on, respectively the interior of the Slimline, see page 14, image 6.1 and 6.2. However, in doing so you should observe a proper movement being provided for at any time.
C.05: P.011 PRODUCT INTEGRATION INTEGRATION Image 1 1 Image 2
C.05: P.012 PRODUCT INTEGRATION INTEGRATION Image 3 Image 4 2
C.05: P.013 PRODUCT INTEGRATION INTEGRATION Image 5 3 45
C.05: P.014 PRODUCT INTEGRATION INTEGRATION Complete Covering Image 6.1 Image 6.2
C.06: P.015 PRODUCT CONTROL CONTROL Programming the remote control (S435): You can also get additional remote controllers for your Flatlift system (optional extra). As the controllers are coded, you have to programme them. 1) To access the programming key, remove the cover (image 1, no. 1) on the receiver. 2) Press down the left hand key (image 1, no. 2). After this, an LED (image 1, no. 3) will then flash slowly. 3) Holding the programming key down, press the first key on the remote control at the same time (image 2, no. 5). On recognising the remote control, the LED (image 1 no. 3) starts to flash rapidly. 4) Release both of the keys. 5) To store a second channel, repeat the procedure starting at step 2 using the second key on the remote control (image 2, no. 6). If your remote control has been successfully recorded, you should hear a soft click in the receiver when you press down the key on the controller. 2 3 4 Image 1 1 5 6 Image 2
C.06: P.016 PRODUCT CONTROL CONTROL Resetting the receiver: It may sometimes occur that the transmitting codes stored in the receiver are lost. In this case, the receiver must be cleared and re-programmed. 1) To access the programming key, remove the cover (image 1, no. 1) on the receiver. 2) Press down both of the programming keys (image 3, no. 2 + 4) until the LED (image 3, no. 3) rapidly flashes. This is the signal that the memory has been successfully cleared. 3) Now re-enter your remote control (refer to P.15). 2 3 4 Image 3 1 Image 4 Receiver contacts (Img.4): Contact 1: Contact 2: Contact 3: Contact 4: Contact 5: Contact 6: Contact 7: Contact 8: Contact 9: Contact 10: unused open outlet open inlet close outlet close inlet unused power supply +12V power supply 0V unused add on antenna Anschluss an eine Raumsteuerung: To assable your Flatlift Slimline to the room control system, disconnect the contacts 2-5 (Abb.4). Connect these cables with the relay outputs of your room control system (Img.5). The relays of the room control system should be open as the case of may be close for 120 sec. Image 5
C.07: P.017 TROUBLE SHOOTING SHOOTING Trouble shooting: If your Flatlift is not working properly, please make sure you check the following things: The Flatlift won t move up or down Is the power cord attached to the control box? S Check the main connection Are all of the plugs properly connected to the control box? (NOTE: plugs which are not connected properly can damage the system) S Check all of the connections Is there any evidence of damage to the cables, the control box, the remote control or the Flatlift? S Damaged components must be exchanged. Please contact us.. The Flatlift has stopped and will only move in the wrong direction. S Is your Flatlift fully extended already? S Is the TV too heavy? S Remote control command possibly deleted! Have you, in error, attached a TV to your Flatlift which is too heavy? S Take the TV off the Flatlift and now see if the Flatlift works. Is the remote control working? S Change the battery in the remote control if necessary. Is the receiver receiving the signals? S When activating the remote control, the relay should click on both channels. (If the receiver does not click, please delete the channels and re-set them. Refer to page 16) The lifting mechanism jerks or stutters? S Please check as to whether another frequency source is also transmitting at 433 Mhz in your house (possible sources of problems: garage door opener, baby phone, alarm system or intercom). With a frequency jammer you will have to change over to a frequency of 868 Mhz! A free changeover from 433 Mhz to 868 Mhz is only possible within the first 7 days subsequent to the date of delivery. Please contact us if this particular point is relevant to you. If you experience any problems setting your system up or you experience an error, you can also contact us over the telephone or via Email: Customer Service: Via email: info@flatlift.de Our telephone service time is 7.30 am - 5.30 pm. The telephone number is +49 (0) 62 41-97 20 10. Please have the following information at hand / or include it in any email that you sent to us: Your customer number Your invoice number or delivery receipt number The purchase date of your Flatlift The name/model of your Flatlift system
C.08: P.018 LEGAL LIGAL NOTICE NOTICE FLATLIFT References Legal Notice FLATLIFT TV Lift Systeme GmbH Gewerbegebiet Südwest Niedesheimer Str. 15 67547 Worms, GERMANY Tel.: +49 (0) 62 41 97 20 10 Fax.: +49 (0) 62 41 97 20 12 info@fl atlift.de www.fl atlift.de Hours of business: Mon-Fri. 7:30 am- 5:30 pm Managing Director: Sascha Rissel HRA Mainz: HRB 40436 USt. (VAT) ID: On request Status of document: JULY 2008 2008 FLATLIFT TV LIFT SYSTEME GMBH