( ) Preliminary Specifications ( ) Final Specifications Module 15.6 (15.55) FHD 16:9 Color TFT-LCD with LED Backlight design Model Name B156HW01 V3 (H/W0: 1A) Note ( ) LED Backlight with driving circuit design Customer Date Approved by Date Checked & Approved by Date Prepared by Jeff Hou 06/29/2009 Note: This Specification is subject to change without notice. NBBU Marketing Division / AU Optronics corporation B156HW01 V3 Document Version : 0.2 1 of 32
Contents 1. Handling Precautions...4 2. General Description...5 2.1 General Specification... 5 2.2 Optical Characteristics... 6 3. Functional Block Diagram...11 4. Absolute Maximum Ratings...12 4.1 Absolute Ratings of TFT LCD Module... 12 4.2 Absolute Ratings of Environment... 12 5. Electrical characteristics...13 5.1 TFT LCD Module... 13 5.2 Backlight Unit... 15 5.2.1 LED characteristics... 15 6. Signal Characteristic...16 6.1 Pixel Format Image... 16 6.2 The input data format... 17 6.3 Integration Interface and Pin Assignment... 18 6.3.1 Connector Description... 18 6.4 Interface Timing... 21 7. Vibration and Shock Test...23 7.1 Vibration Test... 23 7.2 Shock Test Spec:... 23 7.3. Reliability... 23 8. Mechanical Characteristics...24 8.1 LCM Outline Dimension... 24 8.2 Screw Hole Depth and Center Position... 26 9. Shipping and Package...27 9.1 Shipping Label Format... 27 9.2. Carton package... 28 9.3 Shipping package of palletizing sequence... 28 10. Appendix: EDID description...29 B156HW01 V3 Document Version : 0.2 2 of 32
Record of Revision Version and Date Page Old description New Description Remark 0.1 2009/06/23 All Preliminary Edition for Customer 0.2 2009/06/29 All Update H/W:1A B156HW01 V3 Document Version : 0.2 3 of 32
1. Handling Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the Module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. 11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged. 12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. 13) Disconnecting power supply before handling LCD modules, it can prevent electric shock, DO NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT module that a LED light bar build in as a light source of back light unit. It can prevent electros tic breakdown. B156HW01 V3 Document Version : 0.2 4 of 32
2. General Description B156HW01 V3 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a driver circuit, and LED backlight system. The screen format is intended to support the 16:9 FHD (1920(H) x 1080(V)) screen and 262k colors (RGB 6-bits data driver) with LED backlight driving circuit. All input signals are LVDS interface compatible. B156HW01 V3 is designed for a display unit of notebook style personal computer and industrial machine. 2.1 General Specification The following items are characteristics summary on the table at 25 condition: Items Unit Specifications Screen Diagonal [mm] 394.87 Active Area [mm] 344.16 X 193.59 Pixels H x V 1920x3(RGB) x 1080 Pixel Pitch [mm] 0.215X0.215 Pixel Format Display Mode White Luminance (ILED=20mA) (Note: ILED is LED current) [cd/m 2 ] R.G.B. Vertical Stripe Normally White 220 typ. (5 points average) 187 min. (5 points average) Luminance Uniformity 1.25 max. (5 points) 1.53 max. (13 points) Contrast Ratio 400:1 Response Time [ms] 8 typ/16max Nominal Input Voltage VDD [Volt] +3.3 typ. Power Consumption [Watt] 7.5 max. (Include Logic and BLU power) Weight [Grams] 470 max. Physical Size Without inverter, bracket. [mm] Electrical Interface 2 channel LVDS Glass Thickness [mm] 0.5 Surface Treatment Min. Typ. Max. Length - 359.3 359.8 Width - 209.5 210 Thickness - - 5.7 Anti-Glare Support Color 262K colors ( RGB 6-bit ) Temperature Range Operating Storage (Non-Operating) RoHS Compliance [ o C] [ o C] 0 to +50-20 to +60 RoHS Compliance B156HW01 V3 Document Version : 0.2 5 of 32
2.2 Optical Characteristics Product Specification The optical characteristics are measured under stable conditions at 25 (Room Temperature) : Item Symbol Conditions Min. Typ. Max. Unit Note White Luminance ILED=20mA Viewing Angle θr θl ψh ψl 5 points average Horizontal CR = 10 (Right) (Left) Vertical (Upper) CR = 10 (Lower) 187 220 - cd/m 2 1, 4, 5. - - - - 70 70 60 60 - - - - degre Luminance Uniformity δ5p 5 Points - - 1.25 1, 3, 4 Luminance Uniformity δ13p 13 Points - - 1.53 2, 3, 4 Contrast Ratio CR 300 400-4, 6 Cross talk % 4 4, 7 Tr Rising - 2 - e 4, 9 Response Time Red Tf Falling - 6 - TRT Rising + Falling - 8 16 Rx 0.593 0.623 0.653 Ry 0.321 0.351 0.381 msec 4, 8 Color / Chromaticity Coodinates Green Blue Gx 0.306 0.336 0.366 Gy 0.544 0.574 0.604 Bx CIE 1931 0.118 0.148 0.178 By 0.023 0.053 0.083 4 White Wx 0.283 0.313 0.343 Wy 0.299 0.329 0.359 NTSC % - 60 - B156HW01 V3 Document Version : 0.2 6 of 32
Note 1: 5 points position (Ref: Active area) W W /4 W /4 W /4 W /4 H /4 H /4 1 2 H 3 H /4 4 5 H /4 Note 2: 13 points position (Ref: Active area) W W /4 W /4 W /4 W /4 1 0 1 0 H /4 1 0 1 2 3 4 5 H /4 H 6 7 8 H /4 9 1 0 H /4 1 0 1 1 1 2 1 3 Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the minimum test point luminance δ W5 = Maximum Brightness of five points Minimum Brightness of five points δ W13 = Maximum Brightness of thirteen points Minimum Brightness of thirteen points Note 4: Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after B156HW01 V3 Document Version : 0.2 7 of 32
lighting Backlight for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen. Photo detector Field=2 50 cm LCD Panel TFT-LCD Module Center of the screen Note 5: Definition of Average Luminance of White (YL): Measure the luminance of gray level 63 at 5 points,yl = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5 L (x) is corresponding to the luminance of the point X at Figure in Note (1). Note 6: Definition of contrast ratio: Contrast ratio is calculated with the following formula. Contrast ratio (CR)= Brightness on the White state Brightness on the Black state Note 7: Definition of Cross Talk (CT) CT = YB YA / YA 100 (%) Where YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2) B156HW01 V3 Document Version : 0.2 8 of 32
Signal(Relative value) Product Specification Note 8: Definition of response time: The output signals of BM-7 or equivalent are measured when the input signals are changed from Black to White (falling time) and from White to Black (rising time), respectively. The response time interval between the 10% and 90% of amplitudes. Refer to figure as below. 100% 90% "White" "Black" "White" 10% 0% Tr Tf B156HW01 V3 Document Version : 0.2 9 of 32
Note 9. Definition of viewing angle Viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). The 180 viewing angle range is broken down as follows; 90 (θ) horizontal left and right and 90 (Φ) vertical, high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. B156HW01 V3 Document Version : 0.2 10 of 32
3. Functional Block Diagram The following diagram shows the functional block of the 15.6 inches wide Color TFT/LCD 40 Pin. B156HW01 V3 Document Version : 0.2 11 of 32
4. Absolute Maximum Ratings Product Specification An absolute maximum rating of the module is as following: 4.1 Absolute Ratings of TFT LCD Module Item Symbol Min Max Unit Conditions Logic/LCD Drive Vin -0.3 +4.0 [Volt] Note 1,2 4.2 Absolute Ratings of Environment Item Symbol Min Max Unit Conditions Operating TOP 0 +50 [ o C] Note 4 Operation Humidity HOP 5 95 [%RH] Note 4 Storage Temperature TST -20 +60 [ o C] Note 4 Storage Humidity HST 5 95 [%RH] Note 4 Note 1: At Ta (25 ) Note 2: Permanent damage to the device may occur if exceed maximum values Note 3: LED specification refer to section 5.2 Note 4: For quality performance, please refer to AUO IIS (Incoming Inspection Standard). Twb=39 C Operating Range Storage Range B156HW01 V3 Document Version : 0.2 12 of 32
5. Electrical characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Input power specifications are as follows; Product Specification The power specification are measured under 25 and frame frenquency under 60Hz VDD PDD IDD Symble Parameter Min Typ Max Units Note IRush VDDrp Logic/LCD Drive Voltage VDD Power IDD Current Inrush Current Allowable Logic/LCD Drive Ripple Voltage 3.0 3.3 3.6 [Volt] - - 2.0 [Watt] Note 1/2 - - 606 [ma] - - - - 2000 [ma] 100 [mv] p-p Note 1/2 Note 3 Note 1 : Maximum Measurement Condition:Black Pattern at 3.3V driving voltage. (P max =V 3.3 x I black ) Note 2:Measure Condition 90% 3.3V 0V 10% 0.5ms Vin rising time B156HW01 V3 Document Version : 0.2 13 of 32
5.1.2 Signal Electrical Characteristics Input signals shall be low or High-impedance state when VDD is off. Signal electrical characteristics are as follows; Parameter Condition Min Max Unit Vth Differential Input High Threshold (Vcm=+1.2V) - 100 [mv] Vtl Differential Input Low Threshold (Vcm=+1.2V) -100 - [mv] VID Differential Input Voltage 100 600 [mv] Vcm Differential Input Common Mode Voltage 1.125 1.375 [V] Note: LVDS Signal Waveform B156HW01 V3 Document Version : 0.2 14 of 32
5.2 Backlight Unit 5.2.1 LED characteristics Parameter Symbol Min Typ Max Units Condition Backlight Power Consumption PLED - 5.49 5.93 [Watt] (Ta=25 ), Note 1 Vin =12V LED Life-Time N/A 10,000 - - Hour (Ta=25 ), Note 2 IF=20 ma Note 1: Calculator value for reference PLED = VF (Normal Distribution) * IF (Normal Distribution) / Efficiency Note 2: The LED life-time define as the estimated time to 50% degradation of initial luminous. 5.2.2 Backlight input signal characteristics Parameter Symbol Min Typ Max Units Remark LED Power Supply VLED 7.0 12.0 21.0 [Volt] LED Enable Input High Level LED Enable Input Low Level VLED_EN 2.5-5.5 [Volt] - - 0.8 [Volt] PWM Logic Input High Level PWM Logic Input Low Level VPWM_EN 2.5-5.5 - - 0.8 [Volt] [Volt] Define as Connector Interface (Ta=25 ) PWM Input Frequency FPWM 100 200 20k Hz PWM Duty Ratio Duty 5 -- 100 % 15 of 32
6. Signal Characteristic 6.1 Pixel Format Image Following figure shows the relationship of the input signals and LCD pixel format. 1 1920 1st Line R G B R G B R G B R G B 1080th Line R G B R G B R G B R G B 16 of 32
6.2 The input data format R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 Signal Name Description Red Data 5 (MSB) Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0 (LSB) Red-pixel Data Green Data 5 (MSB) Green Data 4 Green Data 3 Green Data 2 Green Data 1 Green Data 0 (LSB) Green-pixel Data Blue Data 5 (MSB) Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0 (LSB) Red-pixel Data Each red pixel's brightness data consists of these 6 bits pixel data. Green-pixel Data Each green pixel's brightness data consists of these 6 bits pixel data. Blue-pixel Data Each blue pixel's brightness data consists of these 6 bits pixel data. Blue-pixel Data RxCLKIN Data Clock The signal is used to strobe the pixel data and DE signals. All pixel data shall be valid at the falling edge when the DE signal is high DE Display Timing This signal is strobed at the falling edge of RxCLKIN. When the signal is high, the pixel data shall be valid to be displayed. VS Vertical Sync The signal is synchronized to RxCLKIN. HS Horizontal Sync The signal is synchronized to RxCLKIN. Note: Output signals from any system shall be low or High-impedance state when VDD is off. 17 of 32
6.3 Integration Interface and Pin Assignment 6.3.1 Connector Description Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation Manufacturer Type / Part Number Mating Housing/Part Number For Signal Connector IPEX or compatible IPEX 20455-040E-12 or compatible IPEX 20353-040T-11 or compatible 6.3.2 Pin Assignment LVDS is a differential signal technology for LCD interface and high speed data transfer device. Pin Signal Description 1 NC No Connection (Reserve) 2 AVDD PowerSupply,3.3V(typical) 3 AVDD PowerSupply,3.3V(typical) 4 DVDD DDC 3.3Vpower 5 NC No Connection (Reserve) 6 SCL DDCClock 7 SDA DDCData 8 Odd_Rin0- -LVDSdifferential data input(r0-r5,g0) 9 Odd_Rin0+ +LVDSdifferential data input(r0-r5,g0) 10 GND Ground 11 Odd_Rin1- -LVDSdifferential data input(g1-g5,b0-b1) 12 Odd_Rin1+ +LVDSdifferential data input(g1-g5,b0-b1) 13 GND Ground 14 Odd_Rin2- -LVDSdifferential data input(b2-b5,hs,vs,de) 15 Odd_Rin2+ +LVDSdifferential data input(b2-b5,hs,vs,de) 16 GND Ground 17 Odd_ClkIN- -LVDSdifferential clock input 18 Odd_ClkIN+ +LVDSdifferential clock input 19 GND Ground Shield 20 Even_Rin0- -LVDSdifferential data input(r0-r5,g0) 21 Even_Rin0+ +LVDSdifferential data input(r0-r5,g0) 22 GND Ground 23 Even_Rin1- -LVDSdifferential data input(g1-g5,b0-b1) 24 Even_Rin1+ +LVDSdifferential data input(g1-g5,b0-b1) 18 of 32
25 GND Ground 26 Even_Rin2- -LVDSdifferential data input(b2-b5,hs,vs,de) 27 Even_Rin2+ +LVDSdifferential data input(b2-b5,hs,vs,de) 28 GND Ground 29 Even_ClkIN- -LVDSdifferential clock input 30 Even_ClkIN+ +LVDSdifferential clock input 31 VLED_GND LED Ground 32 VLED_GND LED Ground 33 VLED_GND LED Ground 34 NC No Connection (Reserve) 35 PWM System PWM Logic Input level 36 LED_EN LED enable input level 37 NC No Connection (Reserve) 38 VLED LED Power Supply 39 VLED LED Power Supply 40 VLED LED Power Supply 19 of 32
Note1: Input signals shall be low or High-impedance state when VDD is off. 20 of 32
6.4 Interface Timing Product Specification 6.4.1 Timing Characteristics Basically, interface timings should match the 1920x1080 /60Hz manufacturing guide line timing. Parameter Symbol Min. Typ. Max. Unit Frame Rate - 50 60 - Hz Clock frequency 1/ TClock - 71.19 85 MHz Vertical Section Horizontal Section Period TV 1088 1130 - Active TVD 1080 Blanking TVB 8 50 - Period TH 990 1050 - Active THD 960 Blanking THB 30 90 - TLine TClock Note : DE mode only 6.4.2 Timing diagram T CLOCK Input Timing Definition ( DE Mode) DOTCLK Input Data Invaild Data Pixel 1 Pixel 2 Pixel 3 Pixel N-1 Pixel N Invaild Data Pixel 1 DE T HB T HD T H DE T VB T VD T V 21 of 32
6.5 Power ON/OFF Sequence Product Specification Power on/off sequence is as follows. Interface signals and LED on/off sequence are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off Power Sequence Timing Value Parameter Min. Typ. Max. Units T1 0.5-10 T2 0-50 T3 200 - - T4 0.5-10 T5 10 - - T6 10 - - T7 0 - - ms T8 10 - - T9 0-10 T10 200 - - T11 0.5-50 T12 0-10 T13 400 - - Note:If T3,T5,T6 couldn t match above specifications, must request T3+T5+T6 > 200ms at least 22 of 32
7. Vibration and Shock Test Product Specification 7.1 Vibration Test Test Spec: Test method: Non-Operation Acceleration: 1.5 G Frequency: 10-500Hz Random Sweep: 30 Minutes each Axis (X, Y, Z) 7.2 Shock Test Spec: Test Spec: Test method: Non-Operation Acceleration: 220 G, Half sine wave Active time: 2 ms Pulse: X,Y,Z.one time for each side 7.3. Reliability Items Required Condition Note Temperature Humidity Bias High Temperature Operation Low Temperature Operation Ta= 40, 90%RH, 300h Ta= 50, Dry, 300h Ta= 0, 300h High Temperature Storage Ta= 60, 35%RH, 300h Low Temperature Storage Ta= -20, 50%RH, 300h Thermal Shock Test ESD Ta=-20 to 60, Duration at 30 min, 100 cycles Contact : ±8 KV Air : ±15 KV Note 1 Note1: According to EN 61000-4-2, ESD class B: Some performance degradation allowed. No data lost. Self-recoverable. No hardware failures. Remark: MTBF (Excluding the LED): 30,000 hours with a confidence level 90% 23 of 32
8. Mechanical Characteristics 8.1 LCM Outline Dimension Product Specification 24 of 32
Note: Prevention IC damage, IC positions not allowed any overlap over these areas. 25 of 32
8.2 Screw Hole Depth and Center Position Maximum Screw penetration from side surface is 2.5mm (See drawing) Screw hole center location, from front surface = 3.10 ± 0.3mm (See drawing) Screw Torque: Maximum 2.5 kgf-cm 26 of 32
9. Shipping and Package 9.1 Shipping Label Format Manufactured 08/05 Model No: B156HW01 AU Optronics MADE IN CHINA (S03) H/W:1A F/W:1 CT:CATYU01XXXXXXX 27 of 32
9.2. Carton package 9.3 Shipping package of palletizing sequence 28 of 32
10. Appendix: EDID description B156HW01 V3 EDID Code Address FUNCTION Value Value Value Note HEX HEX BIN DEC 00 Header 00 00000000 0 01 FF 11111111 255 02 FF 11111111 255 03 FF 11111111 255 04 FF 11111111 255 05 FF 11111111 255 06 FF 11111111 255 07 00 00000000 0 08 EISA Manuf. Code LSB 06 00000110 6 09 Compressed ASCII AF 10101111 175 0A Product Code ED 11101101 237 0B hex, LSB first 13 00010011 19 0C 32-bit ser # 00 00000000 0 0D 00 00000000 0 0E 00 00000000 0 0F 00 00000000 0 10 Week of manufacture 01 00000001 1 11 Year of manufacture 12 00010010 18 12 EDID Structure Ver. 01 00000001 1 13 EDID revision # 03 00000011 3 14 Video input def. (digital I/P, non-tmds, CRGB) 80 10000000 128 15 Max H image size (rounded to cm) 22 00100010 34 16 Max V image size (rounded to cm) 13 00010011 19 17 Display Gamma (=(gamma*100)-100) 78 01111000 120 18 Feature support (no DPMS, Active OFF, RGB, tmg Blk#1) 0A 00001010 10 19 Red/green low bits (Lower 2:2:2:2 bits) C8 11001000 200 1A Blue/white low bits (Lower 2:2:2:2 bits) 95 10010101 149 1B Red x (Upper 8 bits) 9E 10011110 158 1C Red y/ higher 8 bits 57 01010111 87 1D Green x 54 01010100 84 1E Green y 92 10010010 146 1F Blue x 26 00100110 38 20 Blue y 0F 00001111 15 29 of 32
21 White x 50 01010000 80 22 White y 54 01010100 84 23 Established timing 1 00 00000000 0 24 Established timing 2 00 00000000 0 25 Established timing 3 00 00000000 0 26 Standard timing #1 01 00000001 1 27 01 00000001 1 28 Standard timing #2 01 00000001 1 29 01 00000001 1 2A Standard timing #3 01 00000001 1 2B 01 00000001 1 2C Standard timing #4 01 00000001 1 2D 01 00000001 1 2E Standard timing #5 01 00000001 1 2F 01 00000001 1 30 Standard timing #6 01 00000001 1 31 01 00000001 1 32 Standard timing #7 01 00000001 1 33 01 00000001 1 34 Standard timing #8 01 00000001 1 35 01 00000001 1 36 Pixel Clock/10000 LSB 84 10000100 132 37 Pixel Clock/10000 USB 3A 00111010 58 38 Horz active Lower 8bits 80 10000000 128 39 Horz blanking Lower 8bits 78 01111000 120 3A HorzAct:HorzBlnk Upper 4:4 bits 70 01110000 112 3B Vertical Active Lower 8bits 38 00111000 56 3C Vertical Blanking Lower 8bits 8F 10001111 143 3D Vert Act : Vertical Blanking (upper 4:4 bit) 40 01000000 64 3E HorzSync. Offset 3C 00111100 60 3F HorzSync.Width 30 00110000 48 40 VertSync.Offset : VertSync.Width CC 11001100 204 41 Horz&Vert Sync Offset/Width Upper 2bits 00 00000000 0 42 Horizontal Image Size Lower 8bits 58 01011000 88 43 Vertical Image Size Lower 8bits C1 11000001 193 44 Horizontal & Vertical Image Size (upper 4:4 bits) 10 00010000 16 45 Horizontal Border (zero for internal LCD) 00 00000000 0 46 Vertical Border (zero for internal LCD) 00 00000000 0 47 Signal (non-intr, norm, no stero, sep sync, neg pol) 18 00011000 24 30 of 32
48 Detailed timing/monitor 00 00000000 0 49 descriptor #2 00 00000000 0 4A 00 00000000 0 4B 0F 00001111 15 4C 00 00000000 0 4D 00 00000000 0 4E 00 00000000 0 4F 00 00000000 0 50 00 00000000 0 51 00 00000000 0 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 58 00 00000000 0 59 20 00100000 32 5A Detailed timing/monitor 00 00000000 0 5B descriptor #3 00 00000000 0 5C 00 00000000 0 5D FE 11111110 254 5E 00 00000000 0 5F Manufacture 41 01000001 65 A 60 Manufacture 55 01010101 85 U 61 Manufacture 4F 01001111 79 O 62 0A 00001010 10 63 20 00100000 32 64 20 00100000 32 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6A 20 00100000 32 6B 20 00100000 32 6C Detailed timing/monitor 00 00000000 0 6D descriptor #4 00 00000000 0 6E 00 00000000 0 31 of 32
6F FE 11111110 254 70 00 00000000 0 71 Manufacture P/N 42 01000010 66 B 72 Manufacture P/N 31 00110001 49 1 73 Manufacture P/N 35 00110101 53 5 74 Manufacture P/N 36 00110110 54 6 75 Manufacture P/N 48 01001000 72 H 76 Manufacture P/N 57 01010111 87 W 77 Manufacture P/N 30 00110000 48 0 78 Manufacture P/N 31 00110001 49 1 79 Manufacture P/N 20 00100000 32 7A Manufacture P/N 56 01010110 86 V 7B Manufacture P/N 33 00110011 51 3 7C 20 00100000 32 7D 0A 00001010 10 7E Extension Flag 00 00000000 0 7F Checksum 51 01010001 81 SUM 6656 SUM to HEX 1A00 32 of 32