DIGITAL USER MANUAL MENU VOL- VOL+ CH- CH+ TV/AV POWER IR copyright and intellectual property rights The original manufacturer exclusively own or are licensed to use all copyright and other intellectual property rights of this waterproof LCD TV, including the product design, inside structure design, software, and all technical infrastructure relating to it. Any other companies or persons using or violating the mentioned content without the authorization will be taken into legal action. 10"/15" /17"/19"/22"/26"/32" series IP65
Note The information in this manual is subject to change without notice. Thank You for Choosing This Waterproof LCD TV Table of Contents I. SAFETY INSTRUCTIONS...1 II. ACCESSORIES...3 III. OUTLOOK OF THE DIGITAL WATERPROOF LCD TV...4 1. FRONT VIEW...4 2. REAR VIEW...4 3. INPUT TERMINALS...5 4. CONTROLLING BUTTIONS...5 5. REMOTE CONTROL...6 IV.CONNECTION...8 1. Connection the TV...8 2. Connect to the AV/HDMI...8 3. Connect to the PC...8 V. MENU OPERATION...9 VI. TROUBLE SHOOTING...23 Dear Customer, May we take this opportunity to thank you for purchasing this Digital Waterproof LCD TV. We strongly recommend that you carefully study the Operating Instructions before attempting to operate the unit and that you note the listed precautions. I. SAFETY INSTRUCTIONS * Read instructions: All safety/operating instructions should be read before the product is operated. * Keep these instructions: These instructions should be retained for future reference. * Observe all warnings: Adhere to all warnings on the appliance and in the operating instructions. * Follow all instructions: All operating instructions should be followed. * Accessories: Only use accessories specified by the manufacturer. * Check for any possible hazards first such as pipes, electrical cables etc. before the installation. * Do not open the Waterproof LCD TV, contact your dealer if the TV is not operating properly. * Do not attempt to disassemble the unit. This will invalidate your warranty. * Do not drop the unit or make any scratch on the panel when you move the product. Any scratch on the panel or drop of the product may cause functional failure. * Do not press the display panel hard or use sharp objects to clean. * Install the TV in stable place. An unstable TV may cause personal injury, Damage, or malfunction may result. * When moving the Waterproof LCD TV, turn it off and disconnect all cables and the plug. Product damage, electrical shock, or fire hazard may result. * Non-use periods: Unplug this product during lightning storms or non-using periods. When the unit is not used, turn the power off. * Clean only with a light damp cloth. Unplug the power cord from the AC outlet before cleaning the product. Do not use any solvent-containing detergents for cleaning. * Power cord protection: To avoid any malfunctions of the unit and to protect yourself against electric shock, fire or personal injury, please observe the following: 1
- Hold the plug firmly when connecting or disconnecting the AC power cord to this unit. - Do not connect or disconnect the AC power cord when your hands are wet. - Keep the AC power cord away from heating appliances, as the sheathing of the cord may melt. - Never put any heavy object on the AC power cord. - Do not attempt to repair or reconstruct the AC power cord in any way. - Remove dust, dirt, etc. on the plug at regular intervals. - If the unit has been dropped or otherwise damaged, turn off the power and disconnect the AC power cord. - If smoke, occurs or noises are emitted from the unit, turn off the power and disconnect the AC power cord. * The power cord must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product. Do not damage, break or alter the electric cord. Do not cover the *We reccomend that the power supply is connected via a RCB. * Power supply: This product must operate on a power source specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company. * Servicing: Do not attempt to service the product yourself. Removing covers may expose you to high voltage and other dangerous conditions. Refer to qualified service personnel for servicing. * Replacement parts: In case the product needs replacement parts, please make sure that the service person uses replacement parts specified by the manufacturer. Any use of unauthorized parts may result in fire, electric shock and/or other danger. II. ACCESSORIES Please make sure that the following accessories are in the box when you open it. Note: Pictures may deviate. user manual power supply remote controller USER MANUAL screws Mounting Box (option) If any items are missing, Please contact your supplying dealer. 2 3
III. OUTLOOK OF THE DIGITAL WATERPROOF LCD 3. INPUT TERMINALS 1. FRONT VIEW 1 2 3 4 Front panel LCD panel Speakers Controlling buttons 5 1 2 3 4 5 6 DC 12V input Antenna input Video input (yellow) Audio input (red & white) VGA input (optional) HDMI input(optional) * Some Mirror TV no buttons and speakers. 2. REAR VIEW Back cover 4. CONTROLLING BUTTONS 1 1 Mounting points for mounting box Mounting Box 1. MENU: Main menu: To call up or cancel the main menu. 2. VOL- / VOL+ : For increasing and decreasing the volume. 3. CH- / CH+ : For changing channels. 4. TV/AV : Switch from the TV/AV/HDMI/DTV/PC modes 5. POWER : Turns the TV on or off 6. IR : Remote control sensor * Some Mirror TV no buttons and speakers. 3 2 Lockhole for the mounting point Fixing Holes Cable outlet 4 5
5. REMOTE CONTROL POWER For switching on or switching off TV/AV Press this button, a menu, including TV, DTV, AV, HDMI, PC will display. Press the upward or downward keys to select items you want and press right direction key to access. TIMER Switch the TV off within a certain time MUTE Muting the sound: To turn off the sound DISPLAY Information: For displaying the channel and programmed information (TV mode and DTV mode) PMODE Switch from the STANDARD/PERSONAL/MOVIE picture modes SMODE Switch from the PERSONAL/VOICE/MUSICE/THEATRE sound mode OK Select/Confirm: For selecting a menu or confirming a selected option; FAV Under DTV and TV mode, press it to display like's channels list TEXT Under DTV and TV mode, for displaying telexes TV/RADIO Returns: To exchange TV and RADIO mode.(dtv mode) MENU Main menu : To call up or cancel the main menu EXIT Leave the current OSD menu Press it to choose one of the items in the menu and to change the values. Press it to choose one of the items in the menu and to adjust the related values VOL+/- Increasing and decreasing the volume CH+/- Enter the previous channels or next channels 0-9 Select channels directly by pressing the numbers, 0-9, on the remote control -/-- Press the 0-9 directly into the expected channel RECALL Returns to the previously selected Channel. AUTO/LIST Under DTV and TV mode, press it to display channels list EPG Under DTV mode, press this key to show Electronic program Guide SUBTITLE Under DTV modes, press it to hide the current SUBTITLE function LANG Under DTV modes, press it to adjust sound track RED BUTTON Multifunction button: Executing red marked menu items GREEN BUTTON Multifunction button: Executing green marked menu items YELLOW BUTTON Multifunction button: Executing yellow marked menu items CYAN BUTTON Multifunction button: Executing cyan marked menu items NICAM To switch to NI CAM mode mono stereo I II.Only be available in TV programmers with NI CAM transmission, and default mode is mono SUBPAGE Certain pages contain sub-page which are automatically displayed successively. This key is used to stop or resume sub-page acquisition. The indication appears top left HOLD Freeze the page in DTV mode or TEXT mode REVEAL To display or hide the concealed information INDEX This returns to the contents page (usually page 100) SIZE This allows you to display the top or bottom part of the page in increased text size and then return to normal size Attention : Insert the plug,make sure the POWER switch on right side of TV is in power on state. then press POWER or 0~9 button on top of TV and wait for 4-5 seconds. If you use the remote control to switch on the TV,please wait about 4-5 seconds after pressing the power on 6 7
NOTE: 1.Aim the remote control at the infrared window on the television when using. 2.Avoid excessive pressure, dropping and disassembling of the remote control. 3.Avoid pressing keys continuously and quickly, interval between sequential operations should be 2 seconds. In standby mode press 0~9 numeric buttons TV/AV button power button CH+/- button to be able to boot normally V. Menu Operation IV. CONNECTION 1.Connect the TV or DTV (1). Make sure that LCD TV is power off (2). Insert the CATV cable into antenna socket (3). Turn on the TV (4). Select TV or DTV mode (5). Control the volume by VOL-/VOL+ (6). Using CH+/CH- to chose the channel (7). LCD TV can be turned off by power button on remote control 2.Connect the AV or HDMI (1). Make sure that both of AV device and monitor are power off (2). Connect AV device and LCD TV with AV cable (3). Connect audio cable into the audio input jack on LCD TV (4). Turn on the LCD TV, then turn on the AV device (5). SELECT AV or HDMI mode (6). Control the volume by VOL-/VOL+ (7). LCD TV can be turned off by power button on remote control 3.Connect the PC (1). Make sure that both of PC and LCD TV are power off (2). Connect PC and LCD TV with the PC cable, fasten the screws (3). Insert the AC adaptor port into power input jack, connect another port to the power supply (4). Connect the audio cable (5). Turn the LCD TV on, and then turn on the PC (6). Set the input source to PC mode (7). Control the volume by VOL-/VOL+ (8). LCD TV can be turned off by the power button on remote control LANGUAGE Press button to select Language.Press button to select English or RUSSIAN AUTO TUNNING Press button to select Auto-Tuning, press OK button to access the menu.and the EXIT button can be used as the EXIT function when want to leave the menu A 8 9
Press TV/AV button to display the input source list; Press button or TV/AV button to select the input source you want to watch; Press OK button or button to enter the input source; PICTURE Menu menu to display the main menu. to select Picture in the main menu. 1. to select the option that you want to adjust in Picture menu. 2. to change the value. 3.After finishing your adjustment, Press menu button to save and return back to the previous menu. Picture Mode to select the Picture Mode, then the button to select. You can change the value of contrast, brightness, color, sharpness, tint, color temp when the picture is in user mode. Tips: You can press PMODE button on the remote control to change the Picture Mode directly. Contrast to select Sound Mode, then press the button Brightness to select Sound Mode, then press the button Color to select Sound Mode, then press the button Sharpness to select Sound Mode, then press the button ASPECT RATIO to select the Picture Mode, then the button to select Picture Size. (16:9, 4:3, zoom1, zoom2, AUTO) NOISE REDUCTION to select the Picture Mode, then the button to select Picture Mode. (AUTO, LOW, HIGH) SOUND Menu menu to display the main menu. to select Sound in the main menu. 1. Sound menu. to select the option that you want to adjust in 10 11
1. to change the value. 2.After finishing your adjustment, Press menu button to save and return back to the previous menu. Sound Mode to select Sound Mode, then press the button to select. (Available Sound mode: PERSONAL/VOICE/ MUSICE/THEATRE ) Treble to select Sound Mode. then press the button Bass to select Sound Mode. then press the button Auto volume to select Sound Mode. then press the button to select On or Off Surround sound to select Sound Mode. then press the button Timer Menu menu to display the main menu. to select Time in the main menu. to change value, Then press OK button to adjust shutdown time's clock Minute and Second. On TIME to select Sound Mode, Then press the button to enter the next menu. to change value, Then press OK button to adjust start-up time's clock Minute and Second. Sleep Timer to select Sound Mode, then press the button (Off,240 ",180",120",60",30",15",10") Option Menu menu to display the main menu. to select Setup in the main menu. Clock Auto Clock Off TIME to select Sound Mode, then press the button to enter the next menu. Language to select OSD Language. then press the button Audio Language. to select Audio Language. then press the button Subtitle Language. to select Subtitle Language. then press the button Hearing Impaired. to select Hearing Impaired. then press the button to select On or Off. Channel Menu menu to display the main menu. to select Channel in the main menu. 12 13
Auto Turning to select Auto Turning.then press button or ENTER button to enter. Press button to select the option that you want to adjust in the Installation Guide menu. Then press the button to select Country. Press button to select Start, then press the button OK to start auto search. Press button to select Cancel, then press the button EXIT to exit the menu. NOTE: Do not press other key then it will be search analog and digital Signal both in TV and DTV mode, automatically. DTV Manual Turning to select DTV Manual Turning.then press button or ENTER button to into. to select Frequencies. OK to confirm the operation and EXIT to cancel the editing. ATV Manual Turning to select ATV Manual Turning.then press button or ENTER button to into. to select Frequencies. OK to confirm the operation and EXIT to cancel the editing. 14 15
Skip option allows you to skip the current channel. When set ON the program number will be skipped when you select the channel with the CH+/- button. but is you want to restore the channel you have skipped just press the digital button to select this channel and operate as step above, But set it OFF. Program Edit to select Program Edit. then press button or ENTER button to into. 1>Storage Number to select Storage.then press the button to select Number. 2>System to select the sound system and color system respectively. Normally, Pal/ Secam and Auto for color system are included and BG/ DK/L/AUTO, for sound system are available. When the value auto is selected, the system begins to recognize the current color system of the program automatically. 3>Search to select Search. then press the button to select fine tune item in menu. 4>Fine-Tune to select Fine-Tune, If the picture or sound received is not very good you can press the button to conduct fine tune from high frequency to low frequency till best picture sound effect is obtained. 5>SKIP 1>DELETE to select Program, Press the RED button to mark the channel, press the RED button again to confirm the operation. 2>RENAME to select Program, Press the GREEN button to rename the channel. then press the button to select the character that you want. 3>MOVE to select Program, Press the YELLOW button to mark the channel, press the button to Exchange places. 4>SKIP to select Program, Press the BLUE button to mark the channel, Then a LOGO will showed beside the channel. Press OK or EXIT to confirm the operation and cancel the editing. Skip option allows you to skip the current channel. When set ON the program number will be skipped when you select the channel with the CH+/- button. but is you want to restore the channel you have skipped just press the digital button to select this channel and operate as step above, But set it OFF. 5>FAV to select Program, Press the FAV button to mark the channel. Then a LOGO will showed beside the channel. Press OK or EXIT to confirm the operation and cancel the editing. 16 17
PC-Setup Menu (In pc mode) menu to display the main menu. to select Picture in the main menu. to display the PC-Setup menu. or OK to display the next menu. 1. TEXT menu 1>Auto Adjust 2>H-offset to select H-offset, to adjust. 3>V-offset to select V-offset, to adjust. 4>Size to select Size, to adjust. 5>Phase to select Phase, to adjust. 6>Auto Color to select Auto Color, to adjust 1.1 Teletext instructions under ATV mode A) press the button TEXT to start the page for TELETEXT B) press the button RED GREEN YELLOW and BLUE A) SUB.PG INDEX SIZE HOLD REVEAL PG.DN PG.UP B) Press then button TEXT or EXIT to exit. 1.2 Teletext instructions under DTV mode A) TEXT to start the page for TELETEXT B) Press the number button and access the page related. For instance, input 111, then access the page related with 111. C) PG.UP to access the previous page, and press the button PG.DN to access next page D) Press button PG.UP to turn 100 pages upward, and press the button PG.DN to turn 100 pages downward; E) Press then button TEXT or EXIT to exit. 3. My favorite FAV to access the favorite menu as illustrated below: 18 19
The picture above displays current channels listed and set by the user. Move the cursor to select the program and press the button OK to switch the program and press the button EXIT to exit. 5. Sound track switch and language switch LANG to display multi-audio page while the DTV signal is normal. 4. Program List LIST to access the Channel list menu as illustrated below: Press the direction keys to switch among the different tracks repeatedly, stereo, left and right. Different languages for audio are displaying at the center of the screen. Move the cursor to select the language you need. Then press the button OK to confirm and press the button EXIT to get away from the multi-audio page. 6. Subtitle If you want to browse the Subtitle, please press the button subtitle on the remote control to access the subtitle page as illustrated below. 4.1 The picture above displays current channels listed and set by the user. Move the cursor to select the program and press the button OK to switch the program and press the button EXIT to exit. 4.2 Under the normal condition, press the button TV/Radio to switch between the DTV program and Radio. 20 21
7. EPG If you want to get to know the current or future programs which will be showed in the near future, you can press the button EPG on the remote control to access the program guide page. EXIT to exit. VI. TROUBLE SHOOTING PROBLEMS POSSIBLE REASONS MAKE SURE THE POWER IS ON AND BE CONNECTED CORRECTLY MAKE SURE THE USING TV SYSTEM IS RIGHT 7.1 DISPLAY Display the current program information by pressing the button DISPLAY while the D-TV signal is working well. 7.2 Schedule GREEN to display Reminder program table. 7.3 DATE YELLOW to access the daily mode which displays the programs by days. Then press the button to select the character that you want. 7.4 Reminder BLUE to enter program settings menu, you are prompted to set up programs need to be reminded. NO SOUND AND PICTURE POOR RECEPTION DARK PICTURE UNSTABLE PICTURE SNOWFLAKE APPEARANCE POOR COLOR IMAGE IS NOT STABLE AND MAY APPEAR TO VIBRATE HORIZONTAL NOISE ON THE IMAGE VERTICAL BARS OR STRIPES ON THE IMAGE NO EFFECT WHEN REMOTE CONTROLLING MAKE SURE ALL THE INPUTS ARE CONNECTED CORRECTLY THE CHANNEL SELECTION IS NOT DONE PROPERLY RESETTING THE CHANNELS THE VOLUME IS TURNED OFF. THE ANTENNA IS NOT CONNECTED PROPERLY THE BRIGHTNESS AND CONTRAST ARE NOT ADJUSTED PROPERLY. THE ANTENNA IS NOT ADJUSTED PROPERLY. THE COLOR IS NOT PROPERLY THE TV MAY BE RECEIVING ELECTRONICS OR ELECTRO MAGNETIC INTERFERENCE.FROM OTHER EQUIMENT THE COLOR IS NOT PROPERLY ADJUSTED. THE SIGNAL IS TOO WEAK. CHECK THE DISPLAY RESOLUTION AND FREQUENCY ADJUST THE AUTO ADJUST THE PHASE ADJUST THE AUTO ADJUST THE CLOCK CHECK THE BATTERY WITHIN THE REMOTE CONTROL AND REPLACE IF REQUIRED 22 23
WARRANTY CARD CONSUMER INFORMATION This product may contain substances that can be hazardous to the environment if not disposed of properly. Electrical and electronic equipment should never be disposed of with general household waste but must be separately collected for their proper treatment and recovery. The-crossed out bin symbol, placed on the product, reminds you of the need to dispose of the product correctly at the end of its life. In this way you will assist in the recovery, recycling and reuse of many of the materials used in this product. Where possible recycle your packaging. With your help it is possible to reduce the amount of electrical and electronic waste ending up in landfill and to improve quality of life by preventing the release of potentially hazardous substances into the environment. Commodity Product Model Inspector Customer Name Contact Tel Purchasing date Series No. Invoice No. Seller Name & Tel Distributor Name & Tel The product has been proved all functions are working correctly before leaving the original factory. Please make sure you have followed all the safety instructions mentioned in the manual when you take this waterproof LCD TV for repairing. REPAIR INFORMATION DATE CONDITION REPAIRMAN REMARK Correct Disposal of this Equipment (Waste Electrical &Electronics Equipment) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this and recycle it responsibly. Householders should contact either the retailer they purchased from or their local waste authority for details how to dispose of this item safely. 24