VSX Video Switcher Operati Manual Biamp Systems, 007 S.W. Arctic Drive, Beavert, Oreg 97005 U.S.A. (503) 6-787 http://www.biamp.com an affiliate of Rauland-Borg Corp.
blank print update Dec 9/99
VSX TABLE OF CTENTS Frt Panel Rear Panel Remote Ctrol Optis Applicatis Block Diagram Specificatis Warranty pg. pg. 3 pg. pg. 6 pg. 7 pg. 0 pg. INTRODUCTI The ADVANTAGE VSX Video Switcher provides four video s and e video, with source selecti and ctrol functis. Passive switching allows the VSX to be used as either a switcher or rer, and for either video or audio signals. The VSX is designed to operate independently or in cjuncti with other ADVANTAGE products, such as the SPMe Stereo Preamp/Mixer. The VSX Video Switcher is ideally suited for applicatis such as sports bars, meeting rooms, class rooms, auditoriums, multi-media presentati, and tele-cferencing. The VSX is versatile, costeffective, easy to install, and carries a five-year warranty. VSX features include: four video s, each with both BNC and RCA cnectors e video, with both BNC and RCA cnectors frt panel push-butts select from the four sources frt panel infrared receiver for ctrol of switching two rear panel ports for infrared and/or wall-mount ctrols for ctrol of other ADVANTAGE products logic s for ctrol from other ADVANTAGE products translator for interface to third-party ctrollers compatible with most AMX & CRESTR ctrollers switching functi assigns -of- s to a single ring functi assigns single to -of- s selectable back-terati for video or audio applicatis dry ctact relay switching for complete ground isolati covered by Five-Year Gold Seal Warranty UL listed power source AMX is a registered trademark of AMX Corporati. CRESTR is a registered trademark of CRESTR Electrics, Inc.
FRT PANEL channel select ADVANTAGE VSX Video Switcher Error IR 3 () () (3) () (5) () Channel Select ~: These momentary push-butts select which of the four signals is sent to the. To select a desired, press the correspding push-butt (see Remote Ctrol pages & 5). The adjacent LED indicator will light, indicating the selecti. Only e can be selected at a time. If power is lost or turned, Channel Select reverts to Input when power returns. The VSX may be used as a "rer", with a single signal being switched to e of four s (see Applicatis page 9). The VSX may be used with either video or audio signals. From the factory, Inputs ~ have back-terati of 3.9k ohms, which is appropriate for most applicatis. However, internal jumper straps allow selecti of 75 ohm back-terati, which is required ly for specific video applicatis (see Optis page 6). () Error: This red LED indicates when unusable informati is received via ctrol (see Remote Ctrol page & 5). Errors in transmissi/recepti of ctrol commands, or improperly cnected ctrols, will cause the Error indicator to light. (3) IR: This red LED indicates when informati is received via ctrol. If the IR and Error indicators light simultaneously, this may be an indicati of improper installati. Check the locati and wiring of all ctrols. () Internal Infrared Receiver: This green infrared detector receives commands from optial hand-held Infrared Transmitters (see Remote Ctrol page ). A transmitter will work up to 30 feet from the receiver. For best results, there should be an unobstructed of-sight from the transmitter to receiver. When infrared commands are received, the IR indicator will light. If the IR and Error indicators light simultaneously, this may be an indicati of improper installati. The Internal Infrared Receiver should not be located in direct sunlight, or pointed directly at fluorescent lighting. An internal jumper strap is provided to allow the user to bypass the Internal Infrared Receiver (see Optis page 6). (5) Power: When the Power switch is turned, the red "On" LED will light and Channel Select will revert to Input.
REAR PANEL BIAMP SYSTEMS PORTLAND,OREG an affiliate of Rauland-Borg Corp 7V~ 5 watts class 50/60 Hz wiring logic s translator gnd IR IR3 gnd low high gnd IR IR3 gnd IR IR3 3 (7) (6) (5) () (3) () () () Inputs ~: Each is provided both BNC and RCA type cnectors, which are wired in parallel. Inputs ~ will accept any video signals from cameras, VCRs, laser-discs, cable, satellite, etc. The VSX may instead be used as an audio switcher, with Inputs ~ accepting any mo audio signals from mixers, tapes, CDs, VCRs, cable, satellite, etc. Cnectis for audio signals are typically unbalanced, wired with (+) to tip and (ground) to sleeve. However, if all audio signals to be cnected are balanced, they may be wired with (+) to tip and (-) to sleeve (the / grounds are cnected directly, bypassing the VSX). The VSX may also be used as a -in/- video (or audio) "rer", with a single being switched to e of four s (see Applicatis page 9). From the factory, Inputs ~ have back-terati of 3.9k ohms, which is appropriate for most applicatis. However, internal jumpers allow selecti of 75 ohm back-terati, which is required ly for specific video applicatis (see Optis page 6). () Output: The Output is provided both BNC and RCA type cnectors, which are wired in parallel. The VSX is a passive switching device (using dry ctact relays), and will provide an signal identical to the selected signal. The VSX does not provide any processing, synchrizati, or amplificati of signals. The VSX may instead be used as an audio switcher, with Inputs ~ accepting (and the Output providing) mo audio signals. Cnectis for audio signals are typically unbalanced, wired with (+) to tip and (ground) to sleeve. However, if all audio signals to be cnected are balanced, they may be wired with (+) to tip and (-) to sleeve (the / grounds are cnected directly, bypassing the VSX). The VSX may also be used as a -in/- video (or audio) "rer", with a single being switched to e of four s. This is accomplished simply by cnecting to the VSX Output as if it were a single. Inputs ~ are then utilized as the four possible s (see Applicatis page 9). (3) Remote & Remote : These screw terals are for cnecti of optial ctrols (see Remote Ctrol pages & 5). Including the Internal Infrared Receiver, the Remote Translator (), and the Logic Inputs (6), these terals allow ctrol from up to five locatis. Optial ctrols may be wired up to 000 feet from the VSX, using -cductor shielded cable. () Remote Translator: These screw terals are for cnecti of certain third-party ctrollers (such as AMX and CRESTR ), which generate "carrier-stripped" ctrol signals. Two translator s are provided. The Low teral being used for ctrollers which produce a "low" (-5VDC ~ +VDC) when idle. The High teral is for ctrollers which produce a "high" (+VDC ~ +5VDC) when idle. The third-party ctroller must be programmed to a bitstream in the Biamp format (ctact the ctroller manufacturer to detere if their device driver library currently supports the Biamp format). (5) Remote Output: These screw terals are for cnecti to other ADVANTAGE products having similar ctrol capabilities (such as the SPMe, SPM5D, DRC+, PMX8, and EQ8M). Remote Output combines the commands from VSX frt panel switches, ctrols, & logic s, for simultaneous ctrol of additial devices (see Applicatis page 7). (6) Logic Inputs: This 9-pin Subiature D (female) cnector provides four logic s and their related ground. Logic Inputs allow ctrol of the VSX Channel Select switching functi via external logic circuits, ctact closures, or active driver circuits (see Remote Ctrol page 5). Remote ctrol via logic circuits is possible from other ADVANTAGE products, such as the AGII, DRC+, and PMX8 (see Applicatis page 8). Remote ctrol via ctact closures is possible using switches, relays, or certain thirdparty ctrollers (see Applicatis page 9). The Logic Inputs may also be ly ctrolled via active driver circuits (such as a TTL or RS-3 ). Logic Inputs also include a " switching" scheme and internal jumpers for pin assignment. (7) AC Power Cord: The external power transformer provides 7 Volts AC to the VSX, and is detachable via a 5-pin DIN cnector. The VSX has two internal Amp Normal-Blow (A NB) fuses. If fuses should require replacement, use same fuse value and type ly. 3
REMOTE CTROL An infrared receiver is provided the VSX frt panel, however, infrared and wall-mount ctrol is optial. This allows the user to select ly the type and quantity of ctrols necessary for a particular applicati. Remote ctrols affect VSX Channel Select switching, as well as functis other ADVANTAGE products that might be cnected to the VSX. Remote ctrols may be added at any time, and do not require the VSX to be modified, opened, or removed from a rack. There are four ctrol devices: a hand-held Infrared Transmitter, an Infrared Receiver unit, a wall-mount pushbutt Ctroller with status indicators & infrared detector, and a Remote Interface Kit for building custom ctrol panels. Remote ctrol of the VSX is also possible via third-party ctrollers and Logic Inputs. Infrared Transmitter (Biamp #909-0060-00): The transmitter is a hand-held ctrol, which transmits infrared codes unique to Biamp. Therefore, the Transmitter should not affect any other infrared ctrolled equipment (such as TVs or VCRs). Likewise, other infrared ctrollers will not provide proper ctrol of Biamp equipment. The transmitter requires two AAA batteries, which are included with the unit (user installed). The transmitter has twenty-eight butts, ly four of which ctrol functis the VSX. Channel Select ~ butts provide the same functi as Channel Select ~ butts the VSX frt panel. The remaining butts the transmitter may be used to ctrol other ADVANTAGE products, which are cnected to the VSX Remote Output. When used in this way, VSX Channel Select functis may be assigned to the next row of butts, to avoid cflict with the other products (see Optis page 6). For best results, there should be an unobstructed -of-sight from transmitter to receiver. The transmitter will operate up to 30 feet from a receiver. When infrared informati is transmitted to a receiver, the IR LED indicator the VSX frt panel will light. The transmitter is labelled for use with the VSX and SPMe. External Infrared Receiver (Biamp #909-0030-00): The receiver csists of a black plastic box, which ctains an infrared photo detector, an LED indicator, and three screw terals. To install the receiver, first take the frt cover by removing the four screws. Mount the receiver to wall or other surface, using the two screw holes the back cover (screws not included). The receiver should not be mounted in direct sunlight, or pointed directly at fluorescent lighting. For best results, there should be an unobstructed of-sight from transmitter to receiver. The receiver may be wired up to 000 feet from the VSX, using - cductor shielded cable (not included). Re the cable through the access hole the bottom of the receiver. The three screw terals inside the receiver ("GND", "IR", & "IR3") directly correspd to the Remote and Remote terals rear panel of the VSX. Cnect the cable shield to the "GND" teral at each end. Use the two cductors to cnect "IR" to "IR" and "IR3" to "IR3". Replace the receiver frt cover. When the VSX is turned, power is delivered to the receiver. The LED indicator inside the receiver (and the IR LED indicator the VSX frt panel) will light whenever infrared informati is detected. NOTE: The Infrared Receiver includes a "Remote Translator", which allows ctrol via third-party ctrollers (instructis included with receiver). Ctroller (Biamp #909-08-00): The Ctroller is a hard-wired ctrol, which is powered by the VSX. There are no batteries to wear, and it is not easily lost or stolen. The Ctroller may be wired up to 000 feet from the VSX, using -cductor shielded cable (not included). The Ctroller overrides commands to the VSX from any other source (frt panel ctrols, Logic, Translator, & Remote). To install Ctroller, first remove mounting box from circuit board & frt panel. Re cable through knock- hole rear of mounting box. Install mounting box in wall or panel. Three screw terals circuit board ( GND, IR, & IR3 ) correspd to Remote or Remote terals rear panel of VSX. Cnect cable shield to GND terals at each end. Use cductors to cnect IR to IR & IR3 to IR3. Install 3 circuit board & frt panel mounting box. Only four of the Ctroller butts ctrol functis the VSX. The Channel Select butts & indicators provide the same functis as Channel Select the VSX frt panel. The Main Level butts & display do not affect the VSX (the Ctroller is used with a VSX primarily when ctrolling an ADVANTAGE SPMe as well). The Ctroller also includes an infrared detector, which allows it to operate as an Infrared Receiver as well. NOTE: Two additial screw terals ( GND & KEY SWI ) allow an external key-switch (or ctact-closure) to lock- ctrol of Channel Select (and/or Main Level) functis. A -gang DIP switch the Ctroller circuit board allows custom functis to be assigned, such as Channel Select lock-, Main Level lock-, key-lock normallyopen/closed, and infrared detector defeat (instructis included with Ctroller). CHANNEL SELECT CHANNEL SELECT 3 ADVANTAGE SPMe MUTE VOL VOL MAIN LEVEL InfraRed Receiver SPMe Ctroller MUTE MAIN LEVEL
REMOTE CTROL Remote Interface Kit (Biamp #909-00-00): The Remote Interface Kit allows the user to create a customized ctrol panel, using his own switches, enclosure, and panel. It can provide up to 0 butts ( more than standard ctrols), which are support by some other ADVANTAGE products. The VSX itself ly supports butts (Channel Select), but it will also pass commands to other Advantage products which have been cnected to the Remote Output (see Applicatis page 7). The Remote Interface Kit is a tested circuit board assembly, which includes two wiring harnesses. The circuit board cnects to the VSX in exactly the same way the External Infrared Receiver does, using -cductor shielded cable (not included), and may be wired up to 000 feet from the VSX. The three screw terals the circuit board ("GND", "IR", & "IR3") directly correspd to the Remote & Remote terals the rear panel of the VSX. Cnect the cable shield to the "GND" teral at each end. Use the two cductors to cnect "IR" to "IR" and "IR3" to "IR3". When the VSX is turned, power is delivered to the circuit board. The circuit board is.7"w by.65"h, with four mounting holes (" centers) and #6 mounting hardware provided. Complete instructis are included with the Remote Interface Kit. Logic Inputs: The 9-pin Subiature D (female) cnector the rear panel of the VSX provides four logic s and their related ground. Logic Inputs allow ctrol of the VSX Channel Select switching functi via external logic circuits, ctact closures, or active driver circuits. When nothing is cnected to a Logic Input, an internal pull-up resistor keeps it at a "high" idle state. The Logic Input is activated when its goes "low" (less than +VDC). A Logic Input is ctrolled in e of three ways: ) Use an NPN style "open collector" logic from an external device (such as an ADVANTAGE AGII or DRC+) to short the Logic Input to ground. ) Use a switch, relay, or other ctact closure (such as from a third-party ctroller) to short the Logic Input to ground. 3) Use an active TTL or RS-3 driver circuit (such as from a third-party ctroller) to actively drive the Logic Input to a "high" or "low" state. Multiple logic s or ctact closures may be wired in parallel to a single Logic Input. Logic s and ctact closures should be rated for at least 5 Volt / ma operati. Low-current / dry-ctact closures are recommended for reliability. Active driver circuits should not exceed a signal range of -5VDC to +5VDC, and should have a imum pulse width of 50 milli-secds. Logic Input impedances are approximately k ohms for negative voltages, and approximately 0k ohms for positive voltages. Maximum recommended cable length for Logic Inputs is 0 feet. The VSX Logic Inputs include a " switching" scheme (Logic Input overrides Logic Inputs ~, Logic Input overrides Logic Inputs 3 &, and Logic Input 3 overrides Logic Input ). For example, if Logic Input is turned (Channel selected) and then Logic Input is also turned, the VSX will switch to Channel. However, if Logic Input is turned (Channel selected) and then Logic Input 3 is also turned, the VSX will not switch channels. This " switching" also helps limit the amount of unnecessary switching in video-follow-audio applicatis. Logic Input # may be hard-wired to ground, designating Input as the default when no other is selected (see Applicatis page 8). The Logic Input " switching" scheme will be overridden by commands received from other ctrols. When ctrolling the VSX via logic s from an AGII or DRC+, internal jumper straps are provided which assign the VSX Logic Inputs to the correspding pins for those products (see Optis page 6). From the factory, Logic Inputs ~ are assigned to pins ~, with pin 5 being ground. 5 3 9 8 7 6 logic s Third-Party Ctrollers: The VSX may be ly ctrolled by third-party ctrollers in three ways: ) Cnect "carrier stripped" ctrol signals to the VSX Remote Translator (see Rear Panel page 3). ) Cnect ctact closures, logic circuits, or active TTL / RS-3 driver circuits to the VSX Logic Inputs (see Logic Inputs above). 3) Apply "infrared transmitter" signals to the VSX Internal or External Infrared Receivers. The third-party ctroller must be programmed to a bitstream in the Biamp format (ctact the ctroller manufacturer to detere if their device driver library currently supports the Biamp format). 5
OPTIS NOTE: To access internal jumper optis: ) discnect the unit from AC power ) remove the top panel 3) lay the unit with the frt panel facing away ) using needle-nose pliers, move the desired jumper straps as described below 5) replace the top panel. 75 Ohm Back-Terati: From the factory, Inputs ~ have 3.9k ohm back-terati, which is appropriate for most applicatis. However, internal jumpers allow selecti of 75 ohm back-terati, which is required ly for specific video applicatis. To select 75 ohm back-terati, move the Input ~ jumper straps (J0~J0) down e pin, to the "75 OHMS" positi (see diagram below). HI-Z 75 OHMS J0 J30 J0 J0 HI-Z 75 OHMS HI-Z 75 OHMS HI-Z 75 OHMS INPUT INPUT 3 INPUT INPUT RCA jack BNC jack RCA jack BNC jack RCA jack BNC jack RCA jack BNC jack Internal Infrared Receiver Bypass: An internal jumper allows the Internal Infrared Receiver to be bypassed. To bypass the Internal Infrared Receiver, move the "INTERNAL RECV" jumper strap (J3) left e pin, to the "OUT" positi (see diagram below). IR J3 OUT IN INTERNAL RECV IR ERROR Logic Inputs Pin Assignments: When ctrolling the VSX via logic s from an ADVANTAGE AGII or DRC+, internal jumpers allow VSX Logic Inputs to be assigned to correspding pins for those products (refer to AGII & DRC+ manuals). To assign Logic Input pins, move the "SOURCE SELECT" jumper straps (J) to the desired Logic Input Pin Number positis (see diagram below). SOURCE SELECT ERROR IR IR J3 OUT IN INTERNAL RECV C C 3 9 8 3 7 6 6 LOGIC INPUT PIN NUMBER F F J J Remote Ctrol Butt Assignment: When using Remote Output to ctrol additial ADVANTAGE products, VSX Channel Select functis may be assigned to the next row of butts, to avoid cflict with the other products. To assign Channel Select to the secd row of ctrol butts, move the "OPTI Z" jumper strap (J) down e pin, to the "OFF" positi (see diagram below). OFF J OPTI z 6
APPLICATIS Audio/Video Source Selecti SPMe 7V~ 50/60 Hz xlate gnd IR IR3 ze main L R main limit threshold stereo mo te defeat 0 0 3 0 0 0 0 0 0 power in / mute signal present 5 watts class wiring BIAMP SYSTEMS, Portland, Oreg an affiliate of Rauland-Borg Corp. 3 s limit +0 mo ze amp. audio sources paging mo ze speakers stereo main amp. video mitor/projecti misc. VCR cable satellite right main speaker left main speaker video sources VSX BIAMP SYSTEMS Portland, Oreg an affiliate of Rauland-Borg Corp. ADVANTAGE VSX Video Switcher translator 3 logic s gnd IR IR3 gnd low high gnd IR IR3 gnd IR IR3 wall-mount ctroller SPMe Ctroller hand-held infrared transmitter 3 MUTE CHANNEL SELECT 3 MUTE VOL VOL MAIN LEVEL ADVANTAGE SPMe CHANNEL SELECT MAIN LEVEL This diagram shows a VSX used for video source selecti in a "sports bar" applicati. A similar system could be used for classroom applicatis. The VSX Remote Output is cnected to an ADVANTAGE SPMe Remote, allowing combined ctrol of the two units. Wall-mount and/or infrared ctrols provide simultaneous "audio-follow-video" switching of sources, as well as a master volume ctrol. The VSX receives video signals from satellite, cable, VCR, etc., and sends a single to a large-screen video mitor or projector. The SPMe receives stereo audio signals from the same sources, and sends a stereo (with volume ctrol) to the main sound system, as well as providing a mo for a ze sound system. In additi, the SPMe provides an for a paging rophe, which includes automatic "page-over" muting of the audio signals. 7
APPLICATIS Corporate Video Cferencing VOICECRAFTER 7V~ 50/60 Hz BIAMP SYSTEMS Portland, Oreg an affiliate of Rauland-Borg Corp. setup 7 watts class wiring aux aux in MADE IN U.S.A. ctrol main codec codec -0dB 0dB s +0 codec in channel channel +0 audio feed to codec audio feed from codec VOICECRAFTER This device complies with Part 5 of the FCC Rules. Operati is subject to the following two cditis: () This device may not cause harmful interference, and () this device must accept any interference Complies with Part 68, FCC Rules. received, including interference that may cause FCC Reg. No. 6RM USA-35-BR-T undesired operati. Ringer Equivalence 0.0dB member s ( #3) chairman ( #) presentati ( #) autoe 7V ~ 50/60 Hz DC BIAMP SYSTEMS Portland, Oreg an affiliate of Rauland-Borg Corp. main aux stack in main 5 watts class wiring ±VDC logic s expansi s slave -db hp filter last aux post ungated aux pre 8 ungated duck ch8 pre 7 ungated duck ch8 pre 6 ungated duck ch8 pre 5 ungated duck ch8 pre ungated duck ch8 pre 3 ungated duck ch8 pre ungated duck ch8 pre video feed from codec video feed to codec room camera ( #) member camera ( #3) chairman camera ( #) presentati camera ( #) video mitor VSX BIAMP SYSTEMS Portland, Oreg an affiliate of Rauland-Borg Corp. ADVANTAGE VSX Video Switcher translator 3 logic s gnd IR IR3 gnd low high gnd IR IR3 gnd IR IR3 This diagram shows a VSX used for video source selecti in a "corporate video cferencing" applicati. A similar system could be used for "distance learning" applicatis. An ADVANTAGE autoe automatic (voice-activated) mixer accepts the rophe signals. When a rophe becomes active, a correspding Logic Output goes. The Logic Outputs of the autoe are cnected (individually or in specific groups) to the Logic Inputs of the VSX, for "video-follow-audio" switching. Therefore, the VSX will automatically select the appropriate camera when some e speaks. When the "presentati" becomes active, the VSX switches to the "presentati" camera. The "presentati" camera has over all other cameras. (The audio & video "presentati" signals could instead be from a VCR or multi-media device.) The "chairman" camera has over the "member" & "room" cameras, and the "member" camera has over the "room" camera. The "room" camera can be made to come whenever no e is speaking, by wiring the VSX Logic Input directly to ground. Manual or automatic audio override can also be assigned to channel of the autoe mixer. A VOICECRAFTER provides echo canceling and proper interface of audio signals to the video-cferencing codec. 8
USE LY WITH 50V FUSE USE LY WITH 50V FUSE USE LY WITH 50V FUSE USE LY WITH 50V FUSE APPLICATIS Audio Paging Rer telephe paging receptiist paging 30 7V ~ 50/60 Hz DC BIAMP SYSTEMS an affiliate of Rauland Borg Corp. main stack in in v c 30 ch 3 duck phntm phntm phntm 5 watts class wiring VSX ±VDC MADE IN U.S.A. enable ch ch 3 BIAMP SYSTEMS Portland, Oreg an affiliate of Rauland-Borg Corp. ADVANTAGE VSX Video Switcher translator 3 logic s gnd IR IR3 gnd low high gnd IR IR3 gnd IR IR3 switches ze # speakers CMA60 0watt xfmr direct BIAMP SYSTEMS PRECEDENCE an affiliate of is a registered trademark of Rauland-Borg Corp Rauland-Borg Corp CAUTI: replace with same type fuse. 6A - 5V 3A - 30V com 8 5V 50V 70V (00V) chime rec amp in send/return pre compressor threshold adjust mute/ chime stacking in +0V c gnd + com channel 6 noal channel 5 noal channel noal channel 3 tel tel + com + com + com + com + com + com noal channel noal CH. channel noal 5/30V AC 50/60 Hz 375 VA ze #3 speakers CMA60 0watt xfmr direct BIAMP SYSTEMS PRECEDENCE an affiliate of is a registered trademark of Rauland-Borg Corp Rauland-Borg Corp CAUTI: replace with same type fuse. 6A - 5V 3A - 30V com 8 5V 50V 70V (00V) chime rec amp in send/return pre compressor threshold adjust mute/ chime stacking in +0V c gnd + com channel 6 noal channel 5 noal channel noal channel 3 channel tel tel + com + com + com + com + com + com noal noal CH. channel noal 5/30V AC 50/60 Hz 375 VA ze # speakers ze # speakers CMA60 CMA60 0watt xfmr direct BIAMP SYSTEMS PRECEDENCE an affiliate of is a registered trademark of Rauland-Borg Corp Rauland-Borg Corp CAUTI: replace with same type fuse. 6A - 5V 3A - 30V 5/30V AC 50/60 Hz 375 VA 0watt xfmr direct BIAMP SYSTEMS PRECEDENCE an affiliate of is a registered trademark of Rauland-Borg Corp Rauland-Borg Corp CAUTI: replace with same type fuse. 6A - 5V 3A - 30V com 8 5V 50V 70V (00V) com 8 5V 50V 70V (00V) chime chime rec rec amp in amp in send/return pre compressor threshold adjust mute/ chime stacking in +0V c gnd + com send/return pre compressor threshold adjust mute/ chime stacking in +0V c gnd + com channel 6 tel tel + com + com + com + com + com + com channel 6 noal noal channel 5 channel 5 noal noal channel channel noal noal aux s channel 3 channel 3 channel tel tel + com + com + com + com + com + com noal noal channel noal noal CH. CH. channel channel noal noal background music source 5/30V AC 50/60 Hz 375 VA DA8R 7V~ 50/60 Hz watts class wiring DA8R BIAMP SYSTEMS Portland, Oreg an affiliate of Rauland-Borg Corp. OUTPUTS logic s 8 7 6 5 3 CH CH invert logic CH invert logic CH +0 INPUTS +0 This diagram shows a VSX used as an audio rer in a "ice paging" applicati. A similar system could be used for factory or school applicatis. An ADVANTAGE 30 receives signals from the paging sources, and sends a single to the VSX. The 30 may be assigned so signal present in Channels & causes 5dB ducking of Channel 3 (example: over telephe). (When using the VSX as a "rer", the Output cnector is used as a single.) PRECEDENCE CMA60s provide power for the four paging zes. An ADVANTAGE DA8R receives signal from a background music source, and distributes that signal to the Channel the four CMA60s. The VSX provides four s, which are sent to the Channel the four CMA60s. (When using the VSX as a "rer", the Input cnectors are used as the four s.) Paging signal is red to a specific ze via the VSX frt panel Channel Select switches or by switches cnected to the VSX Logic Inputs. The CMA60s allow signal present at the Channel to cause "page-over" muting of the Channel signal. This allows paging (and muting of background music) to be red to a specific ze. In additi, CMA60 muting (and announcement chimes) may be triggered by switches. 9
SPECIFICATIS Maximum Input/Output Voltage: Maximum Input/Output Current: 0Vrms 00mA rms Remote Translator: imum voltage imum voltage switching threshold voltage when idle (high ) voltage when idle (low ) Crosstalk (0Hz ~ 0kHz): Power Requirements: Power Csumpti: +5VDC -5VDC +VDC high ( > +VDC) low ( < +VDC) -70dB 0/0VAC 50/60Hz 8 watts. Dimensis: height ( rack space) width depth Weight:.75 inches (mm) 9 inches (83mm) inches (0mm).5 lbs. (.0kg) 0
BLOCK DIAGRAM (RCA & BNC) (RCA & BNC) 3 (RCA & BNC) (RCA & BNC) Advantage VSX Block Diagram relay relay relay 3 relay 3.9kΩ 75Ω 3.9kΩ 75Ω 3.9kΩ 75Ω 3.9kΩ 75Ω (RCA & BNC) internal infrared receiver roprocessor 3 logic s translator signal translator 3 channel select switches
WARRANTY BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE ORIGINAL PURCHASER OF THE PROFESSIAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL. BIAMP Systems expressly warrants this product to be free from defects in material and workmanship for a period of 5 YEARS from the date of purchase as a new product from an authorized BIAMP Systems dealer under the following cditis.. In the event the warranted BIAMP Systems product requires service during the warranty period, BIAMP Systems will repair or replace, at its opti, defective materials, provided you have identified yourself as the original purchaser of the product to any authorized BIAMP Systems Service Center. Transportati and insurance charges to and from an authorized Service Center or the BIAMP Systems factory for warranted products or compents thereof to obtain repairs shall be the respsibility of the purchaser.. This warranty will be VOIDED if the serial number has been removed or defaced; or if the product has been subjected to accidental damage, abuse, rental usage, alteratis, or attempted repair by any pers not authorized by BIAMP Systems to make repairs; or if the product has been installed ctrary to BIAMP Systems s recommendatis. 3. Electro-mechanical fans, electrolytic capacitors, and the normal wear and tear of appearance items such as paint, knobs, handles, and covers are not covered under this warranty.. BIAMP SYSTEMS SHALL NOT IN ANY EVENT BE LIABLE FOR SPECIAL, INCIDENTAL, OR CSEQUENTIAL DAMAGES, INCLUDING LOST PROFITS, LOSS OF USE, PROPERTY DAMAGE, INJURY TO GOODWILL, OR OTHER ECOMIC LOSS OF ANY SORT. EXCEPT AS EXPRESSLY PROVIDED HEREIN, BIAMP SYSTEMS DISCLAIMS ALL OTHER LIABILITY TO PURCHASER OR ANY OTHER PERSS ARISING OUT OF USE OR PERFORMANCE OF THE PRODUCT, INCLUDING LIABILITY FOR NEGLIGENCE OR STRICT LIABILITY IN TORT. 5. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. BIAMP SYSTEMS EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE REMEDIES SET FORTH HEREIN SHALL BE THE PURCHASER S SOLE AND EXCLUSIVE REMEDIES WITH RESPECT TO ANY DEFECTIVE PRODUCT. THE AGENTS, EMPLOYEES, DISTRIBUTORS, AND DEALERS OF BIAMP SYSTEMS ARE NOT AUTHORIZED TO MODIFY THIS WARRANTY OR TO MAKE ADDITIAL WARRANTIES BINDING BIAMP SYSTEMS. ACCORDINGLY, ADDITIAL STATEMENTS SUCH AS DEALER ADVERTISEMENTS OR REPRESENTATIS DO NOT CSTITUTE WARRANTIES BY BIAMP SYSTEMS. 6. No acti for breach of this warranty may be commenced more than e year after the expirati of this warranty. Thank you for purchasing BIAMP SYSTEMS... AMERICAN SOUND CRAFTSMANSHIP Biamp Systems 007 S.W. Arctic Drive Beavert, Oreg 97005 (503) 6-787 http://www.biamp.com 585.09.00