SMP Connectors Table of Content Connectivity for Table of Contents PAGE Introduction...3-4 Specifications...5-8 MountingHoles...7 Applications...9-12 AssemblyTools...13 AssemblyInstructions...14-18 CompetitorCrossReference...19 2
Connectivity for SMP Connectors Introduction SMP Blind-Mate Connectors Emerson s new Johnson line of SMP Blind-Mate Connectors offers our customers a Micro-Miniature, Slide-On/Snap-On Interconnect System that aid s in the design ofhigh-density packaging as well as axial and radial misalignment issues. The SMP Interface offers superior performance up to 40 GHz and is compatible with all SMP and GPO Connectors. They offer high electrical reliability where extreme shock and vibration condition s are experienced. Applications (Military and Commercial) Phased Arrays Active Antennas Satellites Communication Airborne Radar Shipborne Radar Equipment Ground Radar Hi-Density Modular Axial/ Radial Packaging Misalignment Solutions Markets Aerospace Broadband Instrumentation Telecom Defense Microwave Transmission Options Box-to-Box Cable-to-Board Board-to-Board Cable-to-Panel-to-Board *GPO is a registered trademark of Corning Gilbert. 3
SMP Connectors Introduction Connectivity for Description One of the key benefits of the SMP connector interface is its use in high frequency blind-mate applications. The design of the SMP bullet and shroud system allows for both axial and radial misalignment. The basic system is comprised of an inner bullet adapter, and two outer receptacles called shrouds. The bullet provides a flexible link between the shroud connections. In blind-mate applications, one shroud connector will be typically specified as a snap-on interface and the other as a slide-on. This ensures that the bullet adapter remains fixed in the same shroud connector when the connection is disengaged. The two snap-on interfaces Full Detent (FD) and Limited Detent (LD) each have different engage and disengage coupling forces. The LD is typically selected as the snap-on interface in PCB mount or blind-mate applications, while the FD is mainly used for cabled connections where higher retention forces are required. The two slide-on interfaces Smooth Bore (SM) and Catcher s Mit (CM) allow for reduced connection forces as compared to the snap-on versions. The push-on interface creates a sliding connection that does not physically locate the mating reference planes, allowing for axial and radial misalignment. Both the SM and CM have the same engage/disengage forces; however the CM is typically specified as the shroud configuration in blind-mate applications as its generous lead-in chamfer helps capture and guide the bullet into place. Radial Misalignment Axial Misalignment Bullet Length Shroud 4
Connectivity for SMP Connectors Specifications ELECTRICAL SPECIFICATIONS Impedance: 50 Ohms Frequency Range: BulletAdapter(.254length),Semi-RigidStraightCabledConnectors... 0-40GHz All other In-Series Adapters, Semi-Rigid Right Angle Cabled Connectors, FieldReplaceableConnectors,EndLaunchConnectors,HermeticFeedthroughs... 0-18GHz PCMountConnectors... 0-12 GHz VSWR: (maximum) 0-18 GHz 18-23 GHz 23-26.5 GHz 26.5-40 GHz BulletAdapter(.254length)...1.10 1.15 1.30 1.70 0-18 GHz 18-26.5 GHz 26.5-40 GH Semi-RigidStraightCabledConnectors....20 1.35 1.70 0-4 GHz 4-12 GHz 12-18 GHz AllotherIn-SeriesAdapters... 1.10 1.15 1.20 0-18 GHz Semi-RigidRightAngleCabledConnectors... 1.20 0-18 GHz FieldReplaceableConnectors(typical,measuredbacktobackwithsealpin...1.15 Un-cabledConnectors(dependantonapplication)... NotApplicable Insertion Loss: (db maximum, tested at 10 GHz) In-SeriesAdapters,FieldReplaceableConnectors... 0.10 F(GHz) Semi-RigidCabledConnectors... 0.12 F (GHz) AllotherUn-cabledConnector... NotApplicable Working Voltage: 335 Vrms maximum at sea level, 65 Vrms maximum at 70,000 feet Dielectric Withstanding: Voltage: 500 Vrms minimum at sea level RF High Potential Withstanding Voltage: 325 Vrms minimum at sea level, tested at 4 and 7 MHz Corona Level: 190 Vrms minimum at 70,000 feet Contact Resistance: (milliohms maximum initial, not applicable after environmental testing) CenterContact(ConnectorsandAdapters)... 6.0 OuterContact(ConnectorsandAdapters)... 2.0 CableShieldtoBody(Semi-RigidCabledConnectorsOnly)... 0.5 Insulation Resistance: 5000 megohms minimum RF Leakage: (db typical, tested at 2.5 GHz) CabledandFieldReplaceableConnectors... -80 In-SeriesAdapters... -65 AllotherUn-cabledConnectors... NotApplicable 5
SMP Connectors Specifications Connectivity for Interface Design: MIL-STD-348A, Series SMP MECHANICAL SPECIFICATIONS Engagement Force: (pounds maximum, mated pair) FullDetent(FD)... 15.0 LimitedDetent(LD)... 10.0 SmoothBoreandCatcher smit(smandcm)... 2.0 Disengagement Force: (pounds minimum, mated pair) FullDetent(FD)... 5.0 LimitedDetent(LD)... 2.0 SmoothBoreandCatcher smit(smandcm)... 0.5 Mated Radial Misalignment: (inches maximum allowed, female adapters only) BetweenCenterlinesofMatingPlanes(FD,LD,SM)....010 BetweenCenterlinesofMatingPlanes(CMonly)....020 Mated Axial Misalignment:.010 inches maximum allowed between mating planes (female adapters only) Durability: (mating cycles minimum) FullDetent(allfemaleconnectorsandadapters)... 100 LimitedDetent(femaleadaptersonly)... 500 SmoothBoreandCatcher smit(femaleadaptersonly)... 1000 Contact Retention: 1.5 pounds minimum axial force (captivated contacts only) Cable Retention: (minimum) Axial Force* (lbs) Torque (in-oz) CabledConnectorsforRG-405(.086Semi-Rigid)... 30 16.0 CabledConnectorsforM17/151(.047Semi-Rigid)... 20 N/A *Or cable breaking strength, whichever is less Typical Measured Return Loss Bullet Adapter 127-0901-801 0 127-0801-901 VSWR = 1.10 (0-18 GHz), 1.15 (18-23 GHz), 1.30 (23-26.5 GHz), 1.70 (26.5-40 GHz) -10-20 S11 (db) -30-40 -50-60 0 5 10 15 20 25 30 35 40 6 Frequency (GHz)
Connectivity for SMP Connectors Specifications ENVIRONMENTAL SPECIFICATIONS (Meets or Exceeds the Applicable Paragraph of MIL-PRF-39012) Operating Temperature: -65 C to +165 C Thermal Shock: MIL-STD-202, Method 107, Condition B (except high temp +165 C or max high temp of cable) Corrosion: MIL-STD-202, Method 101, Condition B Shock (specified pulse): MIL-STD-202, Method 213, Condition I Vibration: MIL-STD-202, Method 204, Condition D Moisture Resistance: MIL-STD-202, Method 106 (except step 7b omitted) MATERIAL SPECIFICATIONS Spring Finger (female) and End Launch (male) Bodies: Beryllium Copper per ASTM B196, Gold* plated per MIL-DTL-45204 (.00005 min) Hermetic Seal Bodies (male): Kovar Alloy per ASTM F15, Gold* plated per MIL-DTL-45204 (.00005 min) All other Shroud Bodies (male): Stainless Steel, Type 303, per ASTM A582, Passivated per MIL-DTL-14072 (EL 300) Connector and Adapter Contacts (male and female): Beryllium Copper per ASTM B196, Gold* plated per MIL-DTL-45204 (.00005 min) Hermetic Seal Center Pins: Kovar Alloy per ASTM F15, Gold* plated per MIL-DTL-45204 (.00005 min) EMI/Anti-Rock Rings: Beryllium Copper per ASTM B196, Gold* plated per MIL-DTL-45204 (.00003 min) PC Mount Legs: Brass per ASTM B16, Gold* plated per MIL-DTL-45204 (.00003 min) Connector and Adapter Insulators: PTFE per ASTM D1710 Hermetic Seal Glass: Corning 7070 *All gold plated parts include a.00005 min nickel barrier layer. MOUNTING HOLES Fig 1 Fig 2 Fig 3 This pattern is for reference only. Pattern will vary depending on board type and specific electrical and mechanical requirements. 7
SMP Connectors Specifications Connectivity for Mating Engagement for SMP Series per MIL-STD-348A Notes: 1. Socket to accept mating pin Ø.015±.001 (0.38±0.03). 2. EMI/Anti-Rock Ring configuration optional, used on cabled connectors only. Shall not prevent proper mating engagement. 3. All dimensions shown in inches. Metric equivalents (rounded to nearest 0.01mm) are given for general information only. SMP Female Connector Interface Dimension Cabled Uncabled Minimum Maximum Minimum Maximum A.025 (0.64).035 (0.89).018 (0.46).025 (0.64) SMP Male Connector Interface Dimension Full Detent Limited Detent Smooth Bore Catcher s Mit Minimum Maximum Minimum Maximum Minimum Maximum Minimum Maximum B.051 (1.30).057 (1.45).054 (1.37).060 (1.52).059 (1.50).065 (1.65) N/A N/A C.0205 (0.52).0235 (0.60).0205 (0.52).0235 (0.60) N/A N/A N/A N/A D.003 (0.08).008 (0.20).003 (0.08).008 (0.20).003 (0.08).008 (0.20).043 (1.09).047 (1.19) E.033 (0.84).037 (0.94).033 (0.84).037 (0.94).033 (0.84).037 (0.94) N/A N/A F.139 (3.53).145 (3.68).139 (3.53).145 (3.68).139 (3.53).145 (3.68).123 (3.12).127 (3.23) G.114 (2.90).118 (3.00).118 (3.00).122 (3.10).123 (3.12).127 (3.23) N/A N/A H.124 (3.15).126 (3.20).124 (3.15).126 (3.20) N/A N/A N/A N/A K 35 REF 35 REF 35 REF 35 REF 35 REF 35 REF N/A N/A M 30 REF 30 REF 30 REF 30 REF N/A N/A N/A N/A 8
Connectivity for SMP Connectors Application Straight Solder Type Cabled Female Cable Type VSWR & Freq. Range* Gold Plated Figure M17/151,.047 Semi-Rigid 1.20 Max 0-18 GHz, 127-0692-001 1 1.35 Max 18-26.5 GHz, 1.70 Max 26.5-40 GHz RG-405,.086 Semi-Rigid 1.20 Max 0-18 GHz, 127-0693-001 2 1.35 Max 18-26.5 GHz, 1.70 Max 26.5-40 GHz Fig 1 Fig 2 * Specifications dependant on cable ratings Right Angle Solder Type Cabled Female Cable Type VSWR & Freq. Range Gold Plated A B M17/151,.047 Semi-Rigid 1.20 Max 0-18 GHz 127-0692-101.248 (6.30).197 (5.00) RG-405,.086 Semi-Rigid 1.20 Max 0-18 GHz 127-0693-101.271 (6.88).209 (5.31) Straight PC Mount Male Receptacle Interface Freq. Range Passivated* A Full Detent 0-12 GHz 127-0701-201.218 (5.54) Limited Detent 0-12 GHz 127-1701-201.218 (5.54) Smooth Bore 0-12 GHz 127-2701-201.218 (5.54) Catcher s Mit 0-12 GHz 127-3701-201.234 (5.94) * Base and legs Gold plated brass Mounting hole layout figure 3 on page 7. 9
SMP Connectors Application Connectivity for End Launch Male Receptacle Surface Mount Interface Freq. Range Gold Plated Packaging Full Detent 0-18 GHz 127-0701-801 Stock Full Detent 0-18 GHz 127-0701-802 Tape and Reel -1000 pieces Limited Detent 0-18 GHz 127-1701-801 Stock Limited Detent 0-18 GHz 127-1701-802 Tape and Reel -1000 pieces Smooth Bore 0-18 GHz 127-2701-801 Stock Smooth Bore 0-18 GHz 127-2701-802 Tape and Reel -1000 pieces Mounting hole layout figure 1 on page 7. 2-Hole Flange Mount Male Shroud - Without Contact Interface Passivated Full Detent 127-0701-602 Limited Detent 127-1701-602 Smooth Bore 127-2701-602 2-Hole Flange Mount Male Catcher s Mit Shroud - Without Contact Interface Passivated Catcher s Mit 127-3701-602 10
Connectivity for SMP Connectors Application 2-Hole Flange Mount Male Field Replaceable Interface VSWR & Freq. Range* Passivated Accepts Pin Size Full Detent 1.15 Typical 0-18 GHz 127-0701-612.012 (.030) Limited Detent 1.15 Typical 0-18 GHz 127-1701-612.012 (.030) Smooth Bore 1.15 Typical 0-18 GHz 127-2701-612.012 (.030) * Two connectors mated back to back with hermetic seal fixture Hermetic Seal Male Interface Freq. Range Gold Plated Full Detent 0-18 GHz 127-0711-601 Limited Detent 0-18 GHz 127-1711-601 Smooth Bore 0-18 GHz 127-2711-601 Mounting hole layout figure 2 on page 7. Female to Female Bullet Adapter VSWR & Freq. Range Gold Plated 1.10 Max 0-18 GHz, 127-0901-801 1.15 Max 18-23 GHz, 1.30 Max 23-26.5 GHz, 1.70 Max 26.5-40 GHz 11
SMP Connectors Application Connectivity for Female to Female Adapter VSWR & Freq. Range Gold Plated 1.10 Max 0-4 GHz, 127-0901-811 1.15 Max 4-12 GHz, 1.20 Max 12-18 GHz Male to Male Catcher s Mit Adapter Interface VSWR & Freq. Range Passivated Full Detent 1.10 Max 0-4 GHz, 127-0901-821 1.15 Max 4-12 GHz, 1.20 Max 12-18 GHz Limited Detent 1.10 Max 0-4 GHz, 127-1901-821 1.15 Max 4-12 GHz, 1.20 Max 12-18 GHz Smooth Bore 1.10 Max 0-4 GHz, 127-2901-821 1.15 Max 4-12 GHz, 1.20 Max 12-18 GHz 12
Connectivity for SMP Connectors Assembly Tools SMP Customer Tooling Accurate assembly ofthe Semi-Rigid Cabled Connectors is obtained with the tools listed below. Industry standard devices are used ifpossible for customer convenience and tool compatibility. E. C. D. G. F. B. H. A. I. J. Item Description Part Number A SMP Bullet Extraction Tool 127-0000-900 B SMP Cabled Connector Removal Tool 127-0000-901 C Soldering Vise (does not include clamp inserts or stop screw) 140-0000-962 D Stop Screw for Soldering Vise 140-0000-981 E Semi-Rigid Cable Clamp Inserts for.086" OD Cable 140-0000-964 Semi-Rigid Cable Clamp Inserts for.047" OD Cable 140-0000-997 F Solder Shim for.086" OD Cable 140-0000-984 G SMP Center Contact Holder 127-0000-902 H SMP Interface Locator Tool 127-0000-903 I SMP Right Angle Body Holder 127-0000-904 J SMP FD Shroud Centering Tool 127-0000-905 SMP LD Shroud Centering Tool 127-0000-906 SMP SB Shroud Centering Tool 127-0000-907 13
SMP Connectors Assembly Instructions Connectivity for ASSEMBLY INSTRUCTIONS SMP Straight Female Solder Style for.047 OD Semi-Rigid Cable 1 Identify tools (5 piece parts) and connector parts (3 piece parts). 2. Strip cable jacket and dielectric to dimension shown. Do not nick center conductor. Clean all debris from prepared cable. 3. Insert center conductor into cable stop as shown and place contact onto center conductor. 4. Insert contact into contact holder fixture and clamp cable in vise. Tighten stop screw until light pressure is applied between contact, cable stop and cable jacket. 5. Solder contact to center conductor through solder hole using.016 (0.41) diameter flux core solder wire or solder paste. Use a minimum amount of solder and heat for a good joint. Do not allow heat to build up for a long period of time as cable stop may melt. 6. After solder joint has cooled, remove cable from vise. Remove any excess solder from contact with a sharp blade and clean all debris from contact and cable. 7. Insert contact into connector assembly, making sure cable stop bottoms out against internal shoulder ofconnector body. Insert connector assembly into interface location fixture and clamp cable in vise. Make sure connector assembly is fully engaged within location fixture. Tighten stop screw until light pressure is applied between connector assembly and cable stop. 8. Solder end ofconnector body to cable jacket, using a minimum amount of solder and heat for a full fillet joint. Allow assembly to cool before removing connector from vise and location fixture. Best results are obtained when contact location is flush to.004 (0.10) recessed from reference plane. Interface location fixture is pre-set at factory, but can be adjusted to control location. Cable Group Part Number MIL-C-17/151,.047 Semi-Rigid 127-0692-001 Tool Part Number Cable Vise 140-0000-962 Stop Screw 140-0000-981 Clamp Inserts 140-0000-997 Contact Holder 127-0000-902 Interface Location Fixture 127-0000-903 14
Connectivity for SMP Connectors Assembly Instructions SMP Right Angle Female Solder Style for.047 OD Semi-Rigid Cable 1. Identify tools (5 piece parts) and connector parts (3 piece parts). 2. Strip cable jacket and dielectric to dimension shown. Do not nick center conductor. Clean all debris from prepared cable. 3. Insert center conductor into cable stop as shown. Make sure slot in connector contact is aligned with cross hole in body as shown. Insert cable into cross hole in connector body, making sure cable stop bottoms out against internal shoulder of connector body. 4. Insert connector assembly into interface location fixture and clamp cable in vise using body holder fixture as shown. Tighten stop screw until light pressure is applied between connector body, cable stop and cable jacket. 5. Solder contact to center conductor through rear access port in connector body using a minimum amount of solder and heat for a good joint. 6. After center conductor solder joint has cooled, solder connector body to cable jacket, using a minimum amount ofsolder and heat for a full fillet joint. Take care so that solder does not flow onto anti-rock ring or into rear access port. Allow assembly to cool before removing connector from vise and location fixture. 7. Using a fixture plate as shown, press end cap into rear access port using a.156 (3.96) diameter flat punch until fully seated within body counter bore. 8. Best results are obtained when contact location is flush to.004 (0.10) recessed from reference plane. Interface location fixture is pre-set at factory, but can be adjusted to control location. Cable Group Part Number MIL-C-17/151,.047 Semi-Rigid 127-0692-101 Tool Part Number Cable Vise 140-0000-962 Stop Screw 140-0000-981 Clamp Inserts 140-0000-997 Body Holder 127-0000-904 Interface Location Fixture 127-0000-903 15
SMP Connectors Assembly Instructions Connectivity for SMP Straight Female Solder Style for.086 OD Semi-Rigid Cable 1. Identify tools (6 piece parts) and connector parts (2 piece parts). 2. Strip cable jacket and dielectric to dimension shown. Do not nick center conductor. Clean all debris from prepared cable. 3. Place contact onto center conductor, insert solder shim between cable jacket and contact. 4. Insert contact into contact holder fixture and clamp cable in vise. Tighten stop screw until light pressure is applied between contact, solder shim and cable jacket. 5. Solder contact to center conductor through solder hole using.016 (0.41) diameter flux core solder wire or solder paste. Use a minimum amount of solder and heat for a good joint. Do not allow heat to build up for a long period of time as cable dielectric will expand. 6. After solder joint has cooled, remove solder shim and cable from vise. Remove any excess solder from contact with a sharp blade and clean all debris from contact and cable. 7. Insert contact into connector assembly, making sure cable jacket bottoms out against internal shoulder ofconnector body. Insert connector assembly into interface location fixture and clamp cable in vise. Make sure connector assembly is fully engaged within location fixture. Tighten stop screw until light pressure is applied between connector assembly and cable jacket. 8. Solder end ofconnector body to cable jacket, using a minimum amount of solder and heat for a full fillet joint. Allow assembly to cool before removing connector from vise and location fixture. Best results are obtained when contact location is flush to.004 (0.10) recessed from reference plane. Interface location fixture is pre-set at factory, but can be adjusted to control location. Cable Group Part Number RG-405,.086 Semi-Rigid 127-0693-001 Tool Part Number Cable Vise 140-0000-962 Stop Screw 140-0000-981 Clamp Inserts 140-0000-964 Solder Shim 140-0000-984 Contact Holder 127-0000-902 Interface Location Fixture 127-0000-903 16
Connectivity for SMP Connectors Assembly Instructions SMP Right Angle Female Solder Style for.086 OD Semi-Rigid Cable 1. Identify tools (5 piece parts) and connector parts (2 piece parts). 2. Strip cable jacket and dielectric to dimension shown. Do not nick center conductor. Clean all debris from prepared cable. 3. Make sure slot in connector contact is aligned with cross hole in body as shown. Insert cable into cross hole in connector body, making sure cable jacket bottoms out against internal shoulder ofconnector body. 4. Insert connector assembly into interface location fixture and clamp cable in vise using body holder fixture as shown. Tighten stop screw until light pressure is applied between connector body and cable jacket. 5. Solder contact to center conductor through rear access port in connector body using a minimum amount of solder and heat for a good joint. Do not allow solder to build up along exposed center conductor. 6. After center conductor solder joint has cooled, solder connector body to cable jacket, using a minimum amount ofsolder and heat for a full fillet joint. Take care so that solder does not flow onto anti-rock ring or into rear access port. Allow assembly to cool before removing connector from vise and location fixture. 7. Using a fixture plate as shown, press end cap into rear access port using a.156 (3.96) diameter flat punch until fully seated within body counter bore. 8. Best results are obtained when contact location is flush to.004 (0.10) recessed from reference plane. Interface location fixture is pre-set at factory, but can be adjusted to control location. Cable Group Part Number RG-405,.086 Semi-Rigid 127-0693-101 Tool Part Number Cable Vise 140-0000-962 Stop Screw 140-0000-981 Clamp Inserts 140-0000-964 Body Holder 127-0000-904 Interface Location Fixture 127-0000-903 17
SMP Connectors Assembly Instructions Connectivity for SMP Hermetic Seal Installation 1. Prepare housing panel per figure 2 as shown on page 7. 2. Install solder ring on hermetic seal as shown. Recommended ring size is.103 (2.62) ID x.128 (3.25) OD x.015 (0.38) Thick. 3. Solder in place as shown. Interface Part Number Full Detent 127-0711-601 Limited Detent 127-1711-601 Smooth Bore 127-2711-601 SMP Shroud Installation 1. Install appropriate assembly tool into shroud as shown. 2. While holding tool in place, align flange mount with mounting holes in panel. Install fasteners and torque to 6-8 in/lbs. Shroud Part Number Tool Part Number 127-0701-602 127-0000-905 127-1701-602 127-0000-906 127-2701-602 127-0000-907 127-3701-602 127-0000-907 18
Connectivity for SMP Connectors Cross Reference COMPETITOR CROSS REFERENCE Description Johnson Tensolite Corning Gilbert Micro-Mode SV Microwave AEP Rosenberger Straight Female M17/151 (.047 SR) Cabled 127-0692-001 P651-1CC A014-B11-01 MMSP-6120 1203-4000 7500-1582-011 19K101-270E4 Straight Female RG 405 (.086 SR) Cabled 127-0693-001 P651-2CC A014-D11-01 MMSP-2508 1204-4000 7500-1562-010 19K101-271E4 Right Angle Female M17/151 (.047 SR) Cabled 127-0692-101 P652-1CC A015-B11-01 MMSP-6968 1213-4006 7501-1562-011 19K202-270E4 Right Angle Female RG 405 (.086 SR) Cabled 127-0693-101 P652-2CC A015-D11-01 MMSP-2598 1214-4001 7501-1562-010 19K202-271E4 Field Replaceable.012 Socket 2 Hole Flange Male FD 127-0701-612 P836-4CCF SF1250-6000 Field Replaceable.012 Socket 2 Hole Flange Male LD 127-1701-612 P836-5CCF Field Replaceable.012 Socket 2 Hole Flange Male SB 127-2701-612 P836-6CCF Adapter Bullet Female/Female.254 127-0901-801 P650-1CC A1A1-0001-01 MMSP-2500 1290-4004 5280-1502-000 19K101-K00E4 Adapter Female/Female.769 127-0901-811 P617-1CC MMSP-3829 1290-4007 5280-1502-001 19K115-K00E4 Adapter Male CM/Male FD 127-0901-822 P912-1CCSF A3A6-0539-01 Adapter Male CM/Male LD 127-1901-822 P912-2CCSF Adapter Male CM/Male SB 127-2901-822 P912-3CCSF SF1293-6004 Shroud 2 Hole Flange.165 Wide x.400 High FD 127-0701-602 P670-3SF A001-A23-04 MMSP-2514 SF1254-6006 Shroud 2 Hole Flange.165 Wide x.400 High LD 127-1701-602 P672-3SF A001-A24-04 MMSP-6095 SF1254-6007 Shroud 2 Hole Flange.165 Wide x.400 High SB 127-2701-602 P673-3SF A001-A25-04 MMSP-6067 SF1254-6008 Shroud 2 Hole Flange.235 Wide x.470 High CM 127-3701-602 P671-1SF PC Mount Straight.218 OD.100 Legs Male FD 127-0701-201 P654-5CC A008-L33-01 MMSP-7448 SF1287-6001 PC Mount Straight.218 OD.100 Legs Male LD 127-1701-201 P654-6CC A008-L34-01 MMSP-7449 PC Mount Straight.218 OD.100 Legs Male SB 127-2701-201 P654-7CC A008-L35-01 PC Mount Straight.235 OD.100 Legs Male CM 127-3701-201 P654-8CC End Launch Surface Mount Male FD 127-0701-801 P606-1CC A010-L13-02 MMSP-7457 End Launch Surface Mount Male LD 127-1701-801 P606-2CC A010-L14-02 MMSP-3805 19S202-40ME4 End Launch Surface Mount Male SB 127-2701-801 P606-3CC A010-L15-02 MMSP-7347 Hermetic Feedthrough Shroud Male FD 127-0711-601 P840-9CC A007-L43-01-70 MMSP-2771 Hermetic Feedthrough Shroud Male LD 127-1711-601 P794-2CC A007-L44-01-70 MMSP-2875 Hermetic Feedthrough Shroud Male SB 127-2711-601 A007-L45-01-70 MMSP-2979 19
Emerson Network Power Connectivity Solutions Johnson 299 Johnson Avenue Waseca, MN 56093 USA Tel: 800.247.8256 Fax: 507.833.6287 www.emersonnetworkpower.com/connectivity About Emerson Network Power Connectivity Solutions Emerson Network Power Connectivity Solutions, an Emerson business, serves the needs of wireless communications, telephony and data networks, CATV, security systems, health care and industrial facilities with a full spectrum of broadband copper and fiber optic connectivity products. For more information, visit www.emersonnetworkpower.com/connectivity About Emerson Emerson (NYSE: EMR), based in St. Louis, is a global leader in bringing technology and engineering together to provide innovative solutions to customers through its network power, process management, industrial automation, climate technologies, appliance and tools businesses. For more information, visit www.emerson.com Emerson Network Power The global leader in enabling business-critical continuity. EmersonNetworkPower. com AC Power Systems Connectivity DC Power Systems Embedded Power Inbound Power Integrated Cabinet Solutions Outside Plant Precision Cooling Site Monitoring and Services Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. 2006 Emerson Electric Co SMP11/07 20