Ethernet over Coax EOC110K EOC110R Instruction Manual Ethernet over Coax Adapter Kit Ethernet over Coax Receiver Manual Revision:07/26/2010 For the most up-to-date information, please visit www.startech.com
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech. com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Table of Contents Introduction... 1 Packaging Contents... 1 System Requirements... 1 Installation... 2 Hardware Installation... 2 Driver Installation... 2 Cable Length... 3 Specifications... 4 Technical Support... 5 Warranty Information... 5 i
Introduction The StarTech.com EOC110K Ethernet over Coax extender kit allows you to span a 10/100 network over extremely long distances (up to 1.2km) while still maintaining high speed network connectivity. Allowing Ethernet connections over existing Coaxial cable with little to no modification, providing a perfect solution for a broad range of applications, including connecting isolated user stations from the same or separate building, or overcoming infrastructure obstacles and distances (e.g. older stone/ concrete architecture) where new wiring or wireless may be impossible. Packaging Contents 2 x Ethernet over Coax converter box* 2 x Power Adapter* 1 x Instruction Manual *EOC110R only contains one unit System Requirements 10/100Mbps compatible Ethernet network/equipment Coaxial cabling (RG-59/6/7/11) Available AC power outlet at converter box locations 1
Front View Rear View 2
Installation Hardware Installation NOTE: Both of the converter boxes in the EOC110K kit are identical, so they can be installed at either end, in any order. 1. At one of the locations for the converter box, connect an RJ45 Ethernet cable from the existing Ethernet network or computer network adapter to the LAN port on the converter box. 2. Connect the coax cable to the Link F-Connector on the converter. 3. OPTIONAL: If also transmitting analog cable TV signals over the coax line, connect the CATV F-Connector to a TV or TV receiver. Digital cable TV signals are not supported. 4. Connect the included power adapter. The power LED should light up solid. The LAN Link/Act LED should light up solid when successfully connected to an Ethernet device on the LAN port. 5. Setup additional converter boxes by following the same Steps 1~4 for each location. 6. Once all units are setup, they should be able to automatically locate one another over the coax cabling. The Coax Link and Sync LEDs should stay solid once communication is established. The Coax Link LED will flash during communication. 7. The devices plugged into the LAN ports should now be able to communicate with one another freely. Driver Installation No driver or software installation is required for these converters on any connected computer systems. 3
Cable Lengths Maximum bandwidth (Mbps) based on coaxial cable type and length. Distance 100m ~ 700m RF Bandwidth RG-59 RG-6 RG-7 RG-11 144 144 144 144 800m 128 144 144 144 900m 112 144 144 144 1000m 96 128 144 144 1100m 80 128 144 144 1200m 64 112 128 144 1300m 80 128 144 1400m 80 128 144 1500m 64 112 144 < 30MHz 1600m 96 128 1700m 80 128 1800m 80 128 1900m 64 112 2000m 112 2100m 96 2200m 80 2300m 80 2400m 64 4
Specifications Transmission Standards Connectors (per unit) LEDs (per unit) ITU G.9954, IEEE802.3, IEEE802.3u, IEEE802.3x 2 x F-Connector female 1 x RJ45 female 1 x DC Power 1 x Power 1 x LAN Link/Activity 1 x Coax Link/Activity 1 x Coax Sync Compatible Cabling RG-59, 6, 7, 11 Maximum Distance Power Adapter Operating Temperature Storage Temperature Humidity Dimensions (per unit) Weight (per unit) 2400m (RG-11) 5VDC, 2000mA, center positive, type M plug 0 C ~ 55 C (32 F ~ 131 F) -10 C ~ 65 C (14 F ~ 149 F) 10% ~ 90% RH 280.0mm x 138.0mm x 76.8mm 320g 5
Technical Support StarTech.com s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. Warranty Information This product is backed by a one year warranty. In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear. Limitation of Liability In no event shall the liability of StarTech.com Ltd. and StarTech. com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you. 6
StarTech.com has been making hard-to-find easy since 1985, providing high quality solutions to a diverse IT and A/V customer base that spans many channels, including government, education and industrial facilities to name just a few. We offer an unmatched selection of computer parts, cables, A/V products, KVM and Server Management solutions, serving a worldwide market through our locations in the United States, Canada, the United Kingdom and Taiwan. Visit www.startech.com today for complete information about all our products and to access exclusive interactive tools such as the Cable Finder, Parts Finder and the KVM Reference Guide.