Trim Diagram Da Vinci Chandelier DV1818ALED Diameter: 18" Geometrix is designed by Schonbek with Swarovski Spectra crystal. This design is the proprietary tradedress/trademark of Schonbek Worldwide Lighting Inc. Please save your trim diagram for future reference. Schonbek Worldwide Lighting Inc., 61 Industrial Blvd., Plattsburgh NY 121-18 Tel: 8.836.182 or 518.563.75 www.schonbek.com or www.geometrix-lighting.com For cleaning instructions, visit www.schonbek.com or www.geometrix-lighting.com IMPORTANT: 1 Read through pre-installation and installation instructions Steps 1-2 BEFORE proceeding. 2 Label on back contains important information on your crystal. Please save in case you ever need to order matching crystal. 28 SCHONBEK WORLDWIDE LIGHTING INC., A. SCHONBEK & CO. LTD. WORLDWIDE COPYRIGHT RESERVED US UTILITY PATENT #5,6,43, #D56,1 & D558,3 CANADIAN DESIGN D #116775
Pre-Installation Note: The DV1818LED will require two separately switched 12 A.C. circuits. One circuit will power the G JCD bulbs and one circuit to power the LED power supply. Also needed will be a 12 A.C. wall receptacle to power the wall control unit power supply. 1 st circuit - Wire G circuit: Connect ground wire (marked with green tracer) and power wires (black or white tracers) in outlet box to one circuit. Secure 18 gauge 3 conductor wire to the strain relief in the canopy assembly. 2 nd circuit - Wire LED power supply circuit: Connect silver ground wire and power wires (black and white) (these wires originate from LED power supply located in canopy assembly) in outlet box to one circuit. This wire should be connected to a single pole switch so the LED power supplies can be turned off when not in use. 3 rd circuit - LED circuit: There are two (2) wires required for the LED installation. The first wire will be an (8) conductor silver stem wire that will come from the chandelier frame to the canopy assembly. This wire is to be secured with the strain relief in the canopy assembly then wired accordingly into the dimmers located in the canopy assembly (see Figure 1). The second wire will be the Cat5e communications cable that will come from the wall control unit. This will go through the slot in the top of the canopy assembly and plug into the Cat5e jack. NOTE: There is an off button on the wall plate. This only tells the LEDs to turn off and does not turn off the LED power supplies. Leaving the LED power supplies on may shorten their life. If technical assistance is needed please call us at (8) 836-182 and ask for Da Vinci technical support. FIGURE 1 1 #1 X775 DIMMER #2 X775 DIMMER power supply (12V) XLR 3-pin male to RJ45 female conversion cable IN IN + + - ++ n.c. 1 1 GND R- - DAT G -- + DAT B OPTOTRONIC OT DMX RGB DIM. 2 DMX IN #371 #X758 Outputs to LED modules OPTOTRONIC OT DMX RGB DIM. + + - ++ n.c. 1 1 GND - DAT + DAT DMX IN Outputs to LED modules R- G -- B 3 BLK RED GRN BLU (ONLY use to connect power supply to LED wall control unit) (do NOT use longer cable) #X758 WHITE/BLK WHITE/GRN WHITE/RED WHITE/BLU 4 CIRCUIT #1 TO LED'S CIRCUIT #2 TO LED'S back of LED wall control unit #X758 Sample Program - Solid Alternating Colors 1 Press and hold down the OFF/PRO button until it flashes RED. 2 Press and hold SC5 (scene 5) button until all indicators flash three times. 3 Press SC5 (scene 5) button again to begin programming of scene. 4 Adjust channel sliders 1 and 4 to level 1. 5 Press SC5 (scene 5) button twenty times, indicators 6 Adjust all channel sliders to level 1. 7 Press SC5 (scene 5) button twenty times, indicators 8 Adjust channel sliders 3 and 6 to level 1. Press SC5 (scene 5) button twenty times, indicators 1 Adjust channel sliders 1, 4, 5, 6 to level 1. 11 Press SC5 (scene 5) button once, indicators 12 Adjust channel sliders 2, 4, 5, 6 to level 1. 13 Press SC5 (scene 5) button once, indicators Color of fixture over time with Fade set to zero 14 Adjust channel sliders 3, 4, 5, 6 to level 1. 15 Press SC5 (scene 5) button once, indicators 16 Adjust channel sliders 1, 2, 3, 4 to level 1. 17 Press SC5 (scene 5) button once, indicators 18 Adjust channel sliders 1, 2, 3, 5 to level 1. 1 Press SC5 (scene 5) button once, indicators 2 Adjust channel sliders 1, 2, 3, 6 to level 1. 21 Press SC5 (scene 5) button once, indicators 22 Press and hold OFF/PRO button until BLUE indicator light is on. 23 Press and hold SC5 (scene 5) button, indicator will flash, continue pressing button and adjust MASTER/FADE to second dot from the left, release button. 24 Press OFF/PRO button and adjust MASTER/ FADE to desired brightness level. 25 Press SC5 (scene 5) button to run program. #3737 Category 5E cable (1' supplied - longer cable can be used) 6 5 Connect to CAT.5e jack in canopy. remote cover to switch plate DV1818ALED page 2 DV1818ALED page 15
Changing Fade Time on the XFade6 HEX NUT CROSSBAR RUNNING THREAD All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes. Press and hold down the scene button that you wish to adjust the fade time. The light indicator will flash, keep holding the button and adjust the master dimmer to the desired fade interval. Interval times range from -6 seconds (1 minutes). When you are satisfied with the time, release the button and the indicators will flash three times. Reset the master dimmer to desired level. MIRROR RING MIRROR CABLE SOCKET RUN CABLE THROUGH CABLE GLIDER ON FIXTURE STRAIN RELIEF FOR (8) CONDUCTOR WIRE 11115 FERRITE FILTER Æ 1/16" SUPPORT CABLE RUN COMMUNICATION WIRE(S) TO DIMMERS SCREW COLLAR (8) CONDUCTOR WIRE FROM CHANDELIER FRAME WIRE TO DIMMERS POWER & GROUND WIRES FROM LED POWER SUPPLY CONNECT TO OUTLET BOX DIMMERS (X2) (X775) Sample Program - Rainbow Chase LED POWER SUPPLY (X716) 1 Press and hold down the OFF/PRO button until it flashes RED. 2 Press and hold SC4 (scene 4) button until all indicators flash three times. 3 Press SC4 (scene 4) button again to begin programming of scene. 4 Adjust channel sliders 1 and 4 to level 1. 5 Press SC4 (scene 4) button, indicators will flash showing event was stored. 6 Adjust channel sliders 2 and 5 to level 1. 8 Adjust channel sliders 3 and 6 to level 1. Press SC4 (scene 4) button, indicators will flash showing event was stored. 1 Press and hold OFF/PRO button until BLUE indicator light is on. 11 Press and hold SC4 (scene 4) button, indicator will flash, continue pressing button and adjust MASTER/FADE to second dot from the left, release button. 12 Press OFF/PRO button and adjust MASTER/ FADE to desired brightness level. 7 Press SC4 (scene 4) button, indicators will flash 13 Press SC4 (scene 4) button to run program. showing event was stored. Color of fixture over time Fade Time 2 CIRCUIT BARRIER STRIP (8-68/3) CAT5e JACK (372) 11113/1 CAPACITOR FILTER How to Install Canopy: 11115 FERRITE FILTER 1 Remove the screw collar, mirror and mirror ring from the canopy assembly. Feed suspension cable through running thread from the top so that the cast cable end is seated inside of the cable socket. Attach running thread to crossbar. Attach crossbar using hardware (not provided) to outlet box with cable hanging down. Feed suspension cable through the center hole of the canopy assembly and mount canopy assembly to running thread with supplied hex nut. Feed suspension cable through the mirror ring, mirror and then screw collar in order to mount chandelier frame to suspension cable. Loosen the safety nut on the top of the chandelier frame by turning it counter clockwise and depressing it in order to feed the cable into cable glider and hang to desired height. Slide cable into glider and allow it to play out of the bottom of the frame temporarily. To adjust height, hold the frame with one hand while depressing the safety nut with the other hand until the cable is released. Feed stem wires through stem wire hole in mirror. When chandelier is at desired height, trim stem wires and make connection (see wiring instructions). Install ferrite filter (#11115) on CAT5e communications cable, LED power supply leads and on (8) conductor wires from chandelier to dimmers. After wiring raise mirror ring and mirror to ceiling and secure to running thread with the screw collar. Supplied are 16 cable grips. Clip to support cable and adjust along stem wires as desired. Suspension cable will exit the bottom of the cable glider inside of frame. Cut excess cable off with cable cutters leaving a minimum of 1 of cable. 2 Plug bulbs carefully but completely into socket. Be sure NOT to handle bulbs with bare hands. Use only G JCD bulbs marked suitable for open luminaires OR bearing this symbol: DV1818ALED page 14 DV1818ALED page 3
Programming the XFade6 To avoid damaging, do NOT touch bulb with bare hands. Install bulb with clean cloth or tissue. 18 - G JCD (Supplied - Schonbek #JCD-G-4) 1-18 gauge circuit (72 watts per) 4 Watts Max 12 - modules (24 LEDs) (around mirror body) (Supplied - Schonbek #DV18CLIPA/1) 1-18 gauge circuit 75 Watts Max Install bulbs and be sure to test fixture BEFORE assembly. Hanging Weight: 4 pounds To Delete Scene: If you want to delete a program and start over, press and hold the button until all indicators flash three times. If you chose to delete the program you will need to press the scene button again to start programming. To Add to a Scene: If you want to add to the current program, press but do NOT hold the appropriate scene button. When you are done programming your scene you can choose to program other buttons or exit the program mode by pressing and holding the OFF/PRO button until the blue indicator light is on. How to Assemble Your Da Vinci Chandelier: Put on white cotton gloves to handle crystal. 3 Hang Crystal Chains A from the pin holes in the crystal ring. Twisting of the Crystal Chains and differing lengths are anticipated. These chains help to diffuse the lights and bring more sparkle to your chandelier. 4 Align arrows at top of one crystal section of the sphere (labeled "TOP"). 5 Slide guide tab into slot to line up holes for locking pin. 6 To secure the crystal section, slide pin into hole. Push pin in until it seats. HOLD ON SECURELY TO CRYSTAL SECTION UNTIL YOU ARE SURE PIN IS ENGAGED. 7 Align holes on the bottom of crystal section with the screw on the bottom of the frame (labeled "BOT"). Tighten screw. Repeat steps 3-6 with other four crystal sections. 8 Assemble top by dropping in the crystal semi-circles one at a time. Assemble bottom by screwing in large bottom octagon. (You may push up on the area immediately around the octagon to reach it better.) Adjust the channel fader for the color(s) that you wish to record and the intensity. Zero is off and 1 is full brightness. TIP: Be sure the master dimmer is at full during programming. You can then adjust the dimmer down during playback. After adjusting the sliders press the scene button where you are storing the program once to record and event. All indicators will flash indicating that the event was stored. Repeat the process until you have recorded all the events for your program. NOTE: You can record up to 1 events per scene. DV1818ALED page 4 DV1818ALED page 13
Operating the XFade6 MANUAL CONTROLS Circuit 1 RED AUTOMATIC CONTROL Schonbek Custom Program TWO PERSON ASSEMBLY RECOMMENDED Circuit 1 GREEN Circuit 1 BLUE Circuit 2 RED Circuit 2 GREEN Programmable Scenes 8 CRYSTAL SEMI-CIRCLE TOP #1168 4, 5 & 6 Circuit 2 BLUE Off/Program Button Master Dimmer CABLE GLIDER 3 CRYSTAL RING CRYSTAL SECTION Programming the XFade6 FRAME Press and hold down the OFF/PRO (off/program) button until the indicator light turns red and flashes The scenes button indicators will flash if they have a program. **Not applicable to SC1 (scene 1)** CRYSTAL DIFFUSER A BOTTOM CIRCLE OF CRYSTAL 7 SCREWS BOTTOM DV1818ALED page 12 DV1818ALED page 5
How to run Schonbek custom light show LED indicator MANUAL COLOR SELECTION Slide dimmers - Channels 1 through 6 and master dimmer. 1 st CIRCUIT Channel 1 = red level Channel 2 = green level Channel 3 = blue level 2 nd CIRCUIT Channel 4 = red level Channel 5 = green level Channel 6 = blue level NOTE: 2 circuits are used. Each LED circuit alternates around the frame. PROGRAMMED LIGHT SHOWS Scene buttons - Scenes 1 through 6 and off/program (OFF/PRO) Schonbek Custom Light Show in scene 1 If LED lights do not turn off when off button is pressed run the dimmers to the right and then to the left. NOTE: When returning to manual mode from the Schonbek Custom Light Show, press Scene #2 (SC2), then OFF to clear the program. LED wall control unit IR port for remote WARNING: A very small percentage of individuals may experience epileptic seizures when exposed to certain light patterns or flashing lights. Stop light show immediately if you experience specific symptoms of epilepsy, and consult a physician. #DV18CLIPA/1 To replace the LED module remove plug from top and untwist (2) tabs on bottom slide up out of brackets Any color within the triangle is achievable with the colormix system. A combination of all three primary colors of light (red, green and blue) appears white to the human eye. Combinations of two primaries produce the "secondary" colors (magenta, cyan and yellow). The three primary colors can be mixed to create almost any other color light. By mixing colors, the Correlated Color Temperature (CCT) may be adjusted to blend with the surrounding environment. CCT generally measures the "warmth" or "coolness" of a light source appearance. Color Temperature which is measured in Kelvin, indicates whether a light source has a warm, midrange or cool color appearance. "Warm" light sources have a low color temperature (2-3K) and feature more light in the red/orange/yellow range. Light with a higher color temperature (>5K) features more blue light and in referred to as "cool". DV1818ALED page 6 DV1818ALED page 11
LED Troubleshooting This section gives an outline for troubleshooting problems with your LED system. If technical assistance is needed please call us at (8) 836-182 and ask for Da Vinci technical support. Problem Potential Cause Fix How to take apart your Da Vinci for changing bulbs or washing: One or more switches for the LED system are in the off position. The distribution box power switch is in the off position. Turn all switches for the LED system to the on position. Turn the recorder switch to on. There are two crystal semi-circles surrounding the cable at the top. 1 Remove first semi-circle. 2 Remove second semi-circle. Red, Green, or Blue LED lights will not turn on. The distribution box fuse is blown Communication wires are not connected correctly or loose Replace the blown fuse Check all communication wires for proper wiring and that they are tight 3 Remove bottom by unscrewing large bottom crystal octagon. (You may push up on the area immediately around the octagon to reach it better.) 4 Once the bottom crystal is completely unscrewed, remove the entire bottom circle of crystal. Da Vinci comes apart like an orange, in five sections. Chandelier is not getting 12VAC to the LEDS The slider for that color is in the off position Check power going to the LED circuit is 12VAC Move slider to the on position 5 Locate and remove screws on the bottom of the ball. Do NOT discard screws, they are required for reassembly. 6 Locate the locking pin inside the top of the ball. 7 While holding one section of the ball, remove the pin by pulling it up. The crystal section can then be removed. All Red, Green, or Blue LEDs won t turn on, but another color will. The wire for that color is not connected to the dimmer inside the ball The wire for that color is broken The wall plate is malfunctioning Connect the loose wire to the dimmer 8 Remove the other four crystal sections in the same manner, so that all that remains is the frame with bulbs. Replace necessary bulbs. If you are cleaning your Da Vinci, all crystal parts can now be placed in the dishwasher. The connectors for the LEDs are loose Press connector on to module The wire in the connector is loose Some of the LED lights do not turn on. One or more LED modules are connected backwards. The RGB+ do not match with the red, green, blue, and black wires on the connector One or more LED modules are broke Turn connector around How to clean your Da Vinci: Your Da Vinci crystal panels are dishwasher safe! (Do not attempt to wash or spray the LED modules with any liquid, it will shorten their life) 1 Wash Da Vinci in its own cycle. Do NOT wash with silverware or dishes. Red, Green, or Blue LED lights won t turn off. One or more LED modules have an end connector missing and is grounding on the frame One or more LED modules are shorted to ground on the frame Inside the ball the appropriate color wire is disconnected from the DMX decoder or dimmer. Connect blank connector on last module to stop grounding. Remove any metal that could be causing the LED module to ground to the frame 2 Carefully place crystal sections in dishwasher. Make sure that the crystal sections are not touching each other as this could cause chipping. 3 Use good quality detergent and anti-spotting rinse following the instructions of the dishwasher manufacturer. Cleaners with bleach or ammonia should NOT be used. 4 Allow crystal panels to cool before handling and reassembling your Da Vinci. If sections are brought directly from the hot dishwasher to a cold area, the drastic temperature change could cause crystal to crack. 5 Put on gloves to handle your now clean crystal sections. See page 4 for assembly instructions. DV1818ALED page 1 DV1818ALED page 7
CRYSTAL IDENTIFICATION SHEET TOP 82/1 82/12 82/18 BOTTOM 82/1 82/12 82/18 LARGE BOTTOM OCTAGON 82/4 Frequency of cleaning crystal We know people who clean their crystal every few months, because they love handling the crystals and admiring them close up. Others do a cleaning every six or nine months. To stretch the time between cleanings, dust lightly every two or three months with a feather duster, lambswool duster or make-up brush. Frequency of cleaning depends on location of your Da Vinci and other environmental factors. CRYSTAL SECTIONS 82/1 82/12 82/12 82/16 82/18 82/22 82/26 Crystal needs cleaning when it appears dusty or dull. Just look at your Da Vinci frequently (always enjoyable), and you'll know when it's time for a cleaning. CRYSTAL DIFFUSER 82/14 82/28 82/3 82/14 82/16 82/32 82/32 REPLACING CRYSTAL: If a crystal breaks, you'll see a bare spot in the framework. You will need a set of needlenose pliers to replace the crystal. Make sure when placing pliers onto the metal tab that the ends of the pliers do not go beyond and scratch the crystal. 82/16 82/14 82/32 82/3 A Turn both tabs counterclockwise on either side of pocket where the octagon should be. 82/12 82/28 82/26 B Slide crystal octagon into pocket. Turn both tabs clockwise back to original position to hold the octagon in place. 82/1 82/22 82/18 82/16 82/12 DV1818ALED page 8 DV1818ALED page