Super Blue Chip LED With Right Angle Super Blue Chip LED with Right Angle Features Package in 8mm tape on 7 diameter reel Compatible with automatic placement equipment Compatible with infrared and vapor phase reflow solder process Mono-color type RoHS compliance M3020 Descriptions This SMD series is much smaller than lead frame type components, thus enables smaller board size, higher packing density, reduced storage space, and small equipment. Besides, light weight makes them ideal for miniature applications. Applications Automotive: Backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switches and symbols. General use. Device Selection Guide Chip Part No. Material Emitted Color Lens Color InGaN Super Blue Water Clear TAITRON COMPONENTS INCORPORATED www.taitroncomponents.com Tel: (800)-TAITRON (800)-247-2232 (661)-257-6060 Fax: (800)-TAITFAX (800)-824-8329 (661)-257-6415 Page 1 of 11
Absolute Maximum Ratings (Ta=25 C) Parameter Symbol Value Unit Reverse Voltage VR 5 V Forward Current IF 25 ma Peak Forward Current (Duty 1/10 @1KHz) IFP 100 ma Power Dissipation Pd 110 mw Electrostatic Discharge (HBM) ESD 150 V Operating Temperature Topr -40 ~ +85 C Storage Temperature Tstg -40 ~ +90 C Soldering Temperature Tsol Reflow Soldering: 260 C for 10 seconds Hand Soldering: 350 C for 3 seconds Electro-Optical Characteristics (Ta=25 C) Parameter Symbol Min. Typ. Max. Unit Condition Luminous Intensity IV 28.5 ----- 72.0 mcd Viewing Angle 2θ1/2 ----- 120 ----- deg Peak Wavelength λp ----- 468 ----- nm Dominant wavelength λd 464.5 ----- 476.5 nm IF =20mA Spectrum Radiation Bandwidth λ ----- 35 ----- nm Forward Voltage VF 2.7 3.3 3.7 V Reverse Current IR ----- ----- 50 μa VR=5V Notes: 1. Tolerance of Luminous Intensity ±10% 2. Tolerance of Dominant wavelength ±1.0nm 3. Tolerance of Forward Voltage: ±0.1V www.taitroncomponents.com Page 2 of 11
Forward Current IF (ma) Relative Luminous Intensity (%) Relative Luminous Intensity (%) Relative Luminous Intensity (%) Forward Current IF (ma) Super Blue Chip LED with Right Angle Typical Electro-Optical Characteristics Curves (Ta=25 C) Spectrum Distribution Forward Current vs. Forward Voltage Wavelength (nm) Relative Intensity vs. Ambient Temperature Forward Voltage (V) Relative Intensity vs. Forward Current Ambient Temperature Ta ( C) Forward Current vs. Ambient Temperature Forward Current IF (ma) Radiation Diagram Ambient Temperature Ta ( C) www.taitroncomponents.com Page 3 of 11
Package Dimensions (Unit=mm) Note: The tolerances unless mentioned is ±0.1mm, Unit = mm www.taitroncomponents.com Page 4 of 11
Carrier Tape Dimensions (Unit=mm): Loaded quantity 2000pcs per reel Note: The tolerances unless mentioned is ±0.1mm. Moisture Resistant Packaging www.taitroncomponents.com Page 5 of 11
Reel Dimensions (Unit=mm) Note: The tolerances unless mentioned is ±0.1mm. www.taitroncomponents.com Page 6 of 11
Ordering Information TS P R B R 3020 AN1P2-92-TR70 Lead Free Tape & Reel 7=7 reel 0=2k per reel Factory Location Code Rank Code Size Code in mm Dome Top Super Blue Color Right Angle PCB Type Taitron SMD LED Label Explanation CAT: Luminous Intensity Rank HUE: Dominant Wavelength Rank REF: Forward Voltage Rank www.taitroncomponents.com Page 7 of 11
Rank Combinations Bin Range of Dominant Wavelength Groups Bin Code Min Max Unit Condition A9 464.5 467.5 A A10 467.5 470.5 A11 470.5 473.5 nm IF=20mA A12 473.5 476.5 Bin Range of Luminous Intensity Bin Code Min Max Unit Condition N1 28.5 36.0 N2 36.0 45.0 P1 45.0 57.0 mcd IF=20mA P2 57.0 72.0 Notes: 1. Tolerance of Luminous Intensity ±10% 2. Tolerance of Dominant wavelength ±1.0nm www.taitroncomponents.com Page 8 of 11
Precautions for Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proofs bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30 or less and 90% RH or less. 2.3 After opening the package: The LED s floor life is 1 year under 30 or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave 2 seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. www.taitroncomponents.com Page 9 of 11
5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. www.taitroncomponents.com Page 10 of 11
How to contact us USA HEADQUARTERS 28040 WEST HARRISON PARKWAY, VALENCIA, CA 91355-4162 Tel: (800)-TAITRON (800)-824-8766 (661)-257-6060 Fax: (800)-TAITFAX (800)-824-8329 (661)-257-6415 Email: taitron@taitroncomponents.com Http://www.taitroncomponents.com TAITRON COMPONENTS INCORPORATED TAIWAN BRANCH 6F., NO.190, SEC. 2, ZHONGXING RD., XINDIAN DIST., NEW TAIPEI CITY 23146, TAIWAN R.O.C. Tel: 886-2-2913-6238 Fax: 886-2-2913-6239 TAITRON COMPONENT TECHNOLOG SHANGHAI CORPORATION SUITE 1503, METROBANK PLAZA, 1160 WEST YAN AN ROAD, SHANGHAI, 200052, CHINA Tel: +86-21-5424-9942 Fax: +86-21-2302-5027 www.taitroncomponents.com Page 11 of 11