Displays AND064VT8-LED High Bright TFT LCD Color Module AND064VT8-LED High Bright 6.4 TFT LCD LCD Color Module The AND064VT8-LEDis a compact full color TFT LCD module, that is suitable for computer peripheral, industrial meter, image communication and multi-media. This device consists of an amorphous silicon TFT LCD panel with 2-LED B/L that has 640 x 480 pixels on a 6.4 inch diagonal screen. Product specifications contained herein may be changed without prior notice. It is therefore advisable to contact Purdy Electronics before proceeding with the design of equipment incorporating this product. Features Compatible with VGA-480, VGA-400, VGA-350 mode Support the DENB mode Pixel in stripe configuration Slim and compact Display colors: 262,144 colors Image reversion: Up/Down and Left/Right TTL transmission interface RoHS complliant Mechanical Characteristics Item Standard Value Unit Screen size 6.4 inch (diagonal) inch Display Format 640 x (R, G, B) x 480 dot Active Area 129.6 (H) x 97.44 (V) mm Outline Dimensions 175.4 (W) x 126.9 (H) x 12.5 (D) (Typ.) mm Pixel Pitch 0.2025 (H) x 0.203 (V) mm Pixel Configuration Stripe Surface Treatment Anti-Glare and Wide View film Display Mode Normally White Backlight Middle Power 24 * 2-LED Weight 321 ± 15 Gray scale inversion direction 6 o clock Absolute Maximum Ratings: GND = 0V, Ta = 25ºC Item Symbol Absolute Maximum Rating Unit Remarks Min. Max. Supply Voltage VCC -0.3 +7.0 V Input SIgnals Voltage V-sign -0.3 VCC +0.3 V Note 1 Storage Temperature Tst -30 +80 ºC Operation Temperature Top -30 +80 ºC Note 1: Input signals include CLK, HSYNC, VSYNC, DENB, R[0:5], G[0:5] and B[0:5] 1 Purdy Electronics Corporation 720 Palomar Avenue Sunnyvale, CA 94085 Tel: 408-523-8200 Fax: 408-733-1287 sales@purdyelectronics.com 09/06/10
Displays AND064VT8-LED High Bright TFT LCD Color Module Electrical Characteristics - Recommended Operation Condition for TFT-LCD Panel (Ta = 25ºC) Item Symbol Specifications Unit Remark Min. Typ. Max. Supply Voltage VCC 4.75 5.0 5.25 V Current Dissipation ICC 100 120 ma VCC=+5V Power Consumption PCC 0.5 0.63 W Supply Input Ripple Voltage VCCRP 0.1 Vp-p VCC=+5V Input Signals Voltage (High) VIH +2.6 V Input Signals Voltage (Low) VIL +0.5 V Recommended Operating Conditions for Backlight (Ta = 25 ºC) Item Symbol Min. Typ. Max. Units Remarks Supply Voltage for LED Backlight VLED (11) V Note 1 Supply Current for LED Backlight ILED 17.5 ma Note 2 Backlight Power Consumption PLED 3.08 W Note 1, 3 Note 1: ILED = 17.5 ma, constant current Note 2: The LED driving condition is defined for each LED module. (3 LED Serial) Input current = 17.5 ma * 8 = 140 ma Note 3: PLED = (VLD-1 * ILED-1 + VLED-2 * ILED-2... + VLED-7 + ILED-7 + VLED-8) *2 (light bar) Optical Specifications (Ta = 25 ºC) Viewing Angle Item Symbol Remarks Contrast Ratio Luminance when LCD is white Luminance when LCD i black Min. Specifications Typ. Horizontal θ 21, θ 22 55 60 Vertical θ 12 CR 10 35 40 θ 11 50 55 CR At optimized viewing angle Max. Units 200 400 Response Time Rise Tr θ = 0º 15 30 ms Fall Tf θ = 0º 25 50 Brightness LUM θ = 0º 350 400 cd/m 2 Uniformity U θ = 0º 75 80 % Cross Talk θ = 0º 3.5 % White Chhromaticity X 0.27 0.31 0.35 Y θ = 0º 0.29 0.33 0.37 LED Life Time Ta = 25 ºC +25 ºC 20,000 30,000 hrs deg 2 Purdy Electronics Corporation 720 Palomar Avenue Sunnyvale, CA 94085 Tel: 408-523-8200 Fax: 408-733-1287 sales@purdyelectronics.com 09/06/10
Displays AND064VT8-LED High Bright TFT LCD Color Module Dimensional Outline: 3 Purdy Electronics Corporation 720 Palomar Avenue Sunnyvale, CA 94085 Tel: 408-523-8200 Fax: 408-733-1287 sales@purdyelectronics.com 09/06/10
Displays AND064VT8-LED High Bright TFT LCD Color Module Timing Parameters - AC Electrical Characteristics (VCC = VDD1 = 3.3V, VDD2 = 10V, GND = VSS1 = VSS2 = 0V, Ta = 25ºC) CLK Hsync Vsync Item Symbol Format Min. Typ. Max. Unit Frequency (tc is the period of sampling click. In case of low-frequency, the imae-flicker may occur.) Fc=1/tc All 25.175 MHz tc All 40 ns Period Hp All 31.778 us 800 tc Display Period Hd All 640 tc Pulse Width Hpw All 12 96 139 tc Back-porch Hbp All 12 46 139 tc Front-porch Hfp All 18 tc Hpw + Hbp All 136 142 151 tc Hsync-CLK Hhc All 10 Tc-10 ns Vsync-Hsync Hvh All 0 0 200 tc Period Display Period Vp Vdp 480 16.8 ms 515 525 800 Hp 400 14.3 ms 446 449 480 Hp 350 14.3 ms 447 449 510 Hp 480 480 400 400 350 350 Pulse Width Vpw All 2 2 35 Hp Back-porch Front-porch Vpw + Vbp Vbp Vfp 480 2 33 35 400 2 35 38 350 2 60 63 480 1 10 400 1 12 350 1 37 480 31 35 38 400 33 37 40 350 58 62 65 Data CLK-DATA Dcd All 10 ns DENB DATA-CLK Ddc All 10 ns Horizontal scanning period T1 All 780 800 900 tc Horizontal display period T2 All 640 tc Vertical display period T3 All 480 T1 Frame cycling period T4 All 515 525 800 T1 Hp Hp Hp Hp 4 Purdy Electronics Corporation 720 Palomar Avenue Sunnyvale, CA 94085 Tel: 408-523-8200 Fax: 408-733-1287 sales@purdyelectronics.com 09/06/10
Displays AND064VT8-LED High Bright TFT LCD Color Module Input/Output Terminals TFT-LCD Panel Driving - LCD Module Connector (Reference)-DF9A-31P-1V Pin No. Symbol Function 1 GND Ground (0V) 2 CLK Clock Signal for Sampling IMage DIgital Data 3 HSYNC Horizontal Synchronous Signal 4 VSYNC Vertical Synchronous Signal 5 GND Ground (0V) 6 R0 Red Image Data Signal (LSB) 7 R1 Red Image Data Signal 8 R2 Red Image Data Signal 9 R3 Red Image Data Signal 10 R4 Red Image Data Signal 11 R5 Red Image Data Signal (MSB) 12 GND Ground (0V) 13 G0 Green Image Data Signal (LSB) 14 G1 Green Image Data Signal 15 G2 Green Image Data Signal 16 G3 Green Image Data Signal 17 G4 Green Image Data Signal 18 G5 Green Image Data Signal (MSB) 19 GND Ground (0V) 20 B0 Blue Image Data Signal (LSB) 21 B1 Blue Image Data Signal 22 B2 Blue Image Data Signal 23 B3 Blue Image Data Signal 24 B4 Blue Image Data Signal 25 B5 Blue Image Data Signal (MSB) 26 GND Ground (0V) 27 DENB Enable 28 VCC DC +5.0 V Power Supply 29 VCC DC +5.0 V Power Supply 30 R/L Horizontal Image Shift direction Select Signal 31 U/D Vertical Image Shift Direction Select Signal Backlight Driving Connector: JST BHSR-02VS-1, 2 Pins Pin No. Symbol Function Remarks 1 + Input Terminal (Anode) Red 2 - Input Terminal (Cathode) Black 5 Purdy Electronics Corporation 720 Palomar Avenue Sunnyvale, CA 94085 Tel: 408-523-8200 Fax: 408-733-1287 sales@purdyelectronics.com 09/06/10
Displays AND064VT8-LED High Bright TFT LCD Color Module 6 Purdy Electronics Corporation 720 Palomar Avenue Sunnyvale, CA 94085 Tel: 408-523-8200 Fax: 408-733-1287 sales@purdyelectronics.com 09/06/10
Displays AND064VT8-LED High Bright TFT LCD Color Module 7 Purdy Electronics Corporation 720 Palomar Avenue Sunnyvale, CA 94085 Tel: 408-523-8200 Fax: 408-733-1287 sales@purdyelectronics.com 09/06/10
CONTENTS General Description.2 Features. 2 Application Scope. 2 Driver Board Introduction...3 1. Brief Diagram...3 2. Port Definition..3 3. Pin Assignment 3-5 Keyboard Function Introduction..6 1. Brief Diagram....6 2. Connector Definition....6 3. Keyboard Function Description.6 Mechanical Drawing.. 7.8
GENERAL DESCRIPTION APPLY TO MULTIPLE LCD MODULE: PD064VT4,PD064VT5,PD064VT8 DVI AND VGA AND VIDEO AND S-VIDEO INPUT SYSTEM f H : 48.1 Khz f H :37.9Khz f H :35.1Khz f H :31.5Khz f V : 85Hz f V : 75Hz f V : 72Hz f V : 60 Hz f V : 56 Hz DOT CLK: 50Mhz DOT CLK: 40Mhz DOT CLK: 36Mhz DOT CLK: 25.175Mhz POWER SOURCE DC 12V POWER CONSUMPTION 700 ma, 8.4W Max. OPERATING TEMPERATURE -10 ~ 70 STORAGE TEMPERATURE -20 ~ 80 WEIGHT 280 ±3g FEATURES VGA OR SVGA INPUTS 6-BIT RGB OUTPUT CONVENIENTLY ADJUST IMAGE BY OPERATING KEYBOARD SUPPORT INTERGRATED PLL TECHNOLOGY LOW POWER COMSUMPTION APPLICATION SCOPE SECURITY PC MONITOR INDUSTRY CONTROL MONITOR
DRIVER BOARD INTRODUCTION 1.Brief Diagram (Refer Appendix Page For Details) 2.Port Definition a) JP1------Power input port(dc12v) b) CN1------Power input port(dc12v)(4pin) c) JP2------DVI input port (24+6 pin); d) JP3------Analog VGA input port (15 pin); e) CN3 ------Analog VGA input port (12 pin); f) JP4 ------VIDEO1 IN; g) CN4 ------Video & S-Video input; h) JP5------VIDEO2 IN OR VIDEO OUT; i) JP6------USB IN; j) CN6------USB OUT; k) CN7 ------Keyboard operation port; l) CN8------ISP port; m) CN9------Connection port of AUDIO IN; n) CN10 ------Connection port of SPEAKER OUT; o) CN11 ------Output port for inverter. p) CN12------Connection port of Driver Board with LCD connector (LVDS); q) CN13------Connection port of Driver Board with LCD connector (TTL); * All ports define square pad as the first position in this specification.
3.PIN ASSIGNMENT CN1:Power input port(jst B4B-PH-K-S or compatibility) Pin NO DEF. Pin NO DEF. Pin NO DEF. 1 +12V IN 3 GND 2 +12V IN 4 GND JP2: 24PIN DVI Connector Pin NO DEF Pin NO DEF Pin NO DEF Pin NO DEF 1 RX2N 7 DVISDA 13 NC 19 GND 2 RX2P 8 NC 14 DVI 5V 20 NC 3 GND 9 RX1N 15 GND 21 NC 4 NC 10 RX1P 16 HPD 22 NC 5 NC 11 GND 17 RX0N 23 RXCP 6 DVISCL 12 NC 18 RX0P 24 RXCN CN3: 12PIN VGA Connector (JST B12B-PH-K-S or compatibility) Pin NO DEF Pin NO DEF Pin NO DEF Pin NO DEF 1 SCL 4 BLUE 7 GND 10 HSYNC 2 SDA 5 GND 8 RED 11 VSYNC 3 GND 6 GREEN 9 GND 12 GND JP3: 15PIN VGA Connector Pin NO DEF. Pin NO DEF. Pin NO DEF. 1 RED 6 GND 11 NC 2 GREEN 7 GND 12 SDA 3 BLUE 8 GND 13 HD 4 NC 9 NC 14 VD 5 GND 10 CON 15 SCL
CN4: VIDEO AND S-VIDEO IN (JST B5B-PH-K-S or compatibility) Pin NO DEF. Pin NO DEF. 1 GND 5 GND 2 AV1 6 SV_Y 3 GND 7 GND 4 SV_C 8 AV2 CN5: VIDEO OUT (JST B2B-PH-K-S or compatibility) Pin NO DEF. Pin NO DEF. 1 GND 2 VIDEO OUT CN6: USB OUT (JST B4B-PH-K-S or compatibility) Pin NO DEF. Pin NO DEF. 1 USB_+5V 3 DP 2 DM 4 USB_GND CN7: Key Connector (JST B14B-PH-K-S or compatibility) Pin NO DEF. Pin NO DEF. Pin NO DEF. 1 KEY7 6 KEY2 11 KEY_PWOER 2 KEY6 7 KEY1 12 GND 3 KEY5 8 GND 13 IR 4 KEY4 9 LED_R 14 +5V 5 KEY3 10 LED_G CN8: ISP Connector (JST B4B-PH-K-S or compatibility) Pin NO DEF. Pin NO DEF. 1 +5V 3 ISP SDA 2 ISP SCL 4 GND
CN9: AUDIO IN Connector (JST B4B-PH-K-S or compatibility) Pin NO DEF. Pin NO DEF. 1 GND 3 GND 2 AUDIO IN L 4 AUDIO IN R CN10: SPEAKER OUT Connector (JST B4B-PH-K-S or compatibility) Pin NO DEF. Pin NO DEF. 1 R OUT+ 3 L OUT+ 2 R OUT- 4 L OUT- CN12: TTL Connector Pin NO DEF. Pin NO DEF. Pin NO DEF. Pin NO DEF. 1 GND 11 R5 21 B1 31 U/D 2 DCLK 12 GND 22 B2 32 NC 3 DHS 13 G0 23 B3 33 NC 4 DVS 14 G1 24 B4 34 NC 5 GND 15 G2 25 B5 6 R0 16 G3 26 GND 7 R1 17 G4 27 DEN 8 R2 18 G5 28 P_VCC 9 R3 19 GND 29 P_VCC 10 R4 20 B0 30 R/L
CN13: LVDS Connector Pin NO DEF. Pin NO DEF. Pin NO DEF. Pin NO DEF. 1 P_VCC 9 RXO1-17 RXO3-25 GND 2 P_VCC 10 RXO1+ 18 RXO3+ 26 GND 3 P_VCC 11 RXO2-19 RXE0-27 RXEC- 4 GND 12 RXO2+ 20 RXE0+ 28 RXEC+ 5 GND 13 GND 21 RXE1-29 RXE3-6 GND 14 GND 22 RXE1+ 30 RXE3+ 7 RXO0-15 RXOC- 23 RXE2-8 RXO0+ 16 RXOC+ 24 RXE2+ CN5: Inverter Connector (JST B6B-PH-K-S or compatibility) Pin NO DEF. Pin NO DEF. Pin NO DEF. 1 GND 3 ADJ 5 VCC 2 GND 4 ON/OFF 6 VCC KEY BOARD INTRODUCTION 1.Brief Diagram (Refer Appendix Page For Details) 2.Connector Definition CN1 This connector connected to key operation port of driver board. 3.OSD Function Description If you want to get the best effect, an adjustment of keyboard is required. When first press the menu key, OSD enter the menu operation status (the fist item is picture), called nonadjustable status; press enter key, enter the adjustment status and you can adjust the value of the highlight submenu item by press left or right key; press the enter key again you can exit the adjustment status and save the value at the same time. In the nonadjustable status, press the menu key could switch menu items. The different menu displayed when input different signal source. The menus item shown as following:
Analog VGA input status: MENU ITEM SUBMENU DESCRIPTION Brightness Adjust the display brightness Contrast Adjust the picture contrast Picture Color Setting Function Focus Adjust the picture scan mode Clock Adjust the clock frequency H-Position Adjust the picture horizontal position V-Position Adjust the picture vertical position Native Setting the color temperature C9300 C6500 User Input Signal Select the input signal source: PC-VGA; AV1; AV2; TV. Language Select the OSD language: Chinese; English. OSD Adjust the OSD display horizontal position H-Position OSD Adjust the OSD vertical position V-Position Reset Reset the factory defaults Analog Video or S-video signal input: MENU ITEM SUBMENU DESCRIPTION Brightness Adjust the display brightness Contrast Adjust the picture contrast Picture Color Adjust the picture color Tint Adjust the picture tint Sharpness Adjust the picture sharpness Sound Volume Adjust the Audio output AMP Input Signal Select the input signal source: PC-VGA; AV1; AV2;. Language Select the OSD language: Chinese; English. System setting Blue screen ON: Non-signal display blue screen. OFF: Non-signal display white screen Rotation Adjust the OSD display position: Mirror and flip Wide screen Switch between 16:9 and 4:3
Notes: Do as foregoing description if want to get favorite image. But the best state is set before shipment Occasional flare of Image may occur when starting the LCD Monitor, it is normal phenomena because of auto adjustment internal. Particularly there are snow-flare and bad pictures because that timing does not mat ch with the sequence, please do an auto or handle adjustment.
MECHANICAL DRAWING Driver Board Outline: 132.0*90.0*16mm Top layer High (Max): 13.8 mm Board Thickness: 0.6 mm Screw: D4.0mm
Key Board
INV Content General Description.1 Application Scope..1 Driver Board Introduction..2 1. Port Definition.2 2. Electrical Requirements 3 Mechanical Drawing..4
INV
INV General Description This LED backlight driver board for PD064VT8 Application Scope Storage temperature: -40~+85 Storage Humidity : 10%~90% RH, non-condensing Operation temperature: -30~+80 Operation Humidity : 10%~90% RH, non-condensing Driver Board Introduction 1. Port Definition 2. CN1: Input Connector ( ) PIN No Symbol Function Remark 1 VIN DC +12V Input 2 VIN DC +12V Input 3 Vcon ON/OFF control Note1 4 Vbrt Brightness control Note2 5 GND Ground 6 GND Ground Note1: Vcon ON=+5V OFF=0V Note2:
INV CN2: Output connector adapter to JST BHR-02VS-1 PIN No Symbol Function Remark 1 LED+ Power supply for backlight unit 2 LED- Ground for backlight unit CN3: Output connector adapter to JST BHR-02VS-1 PIN No Symbol Function Remark 1 LED+ Power supply for backlight unit 2 LED- Ground for backlight unit
INV 2: Electrical Requirements Input Characteristics Item Symbol Conditions Input Voltage Input Current Input Power Values Min. Type Max. V IN Vin=DC+12V 10.2 12 13.8 V I IN Pin Vin=12V Vcon=5V Vbrt=0V Vin=12V Vcon=5V Vbrt=0V Unit - 380 - ma 4.6W Remark Output Characteristics Item Symbol Conditions output Voltage output Current V out I out Vcc=12V Vcon=5V Vcc=12V Vcon=5V Values Min. Type Max. Unit 9.2 9.8 11 V 300 320 340 ma Remark
INV Mechanical Drawing
INV Item List: LED backlight driver board Cable