177 PHOTO PHOTO Digital Sensor SERIES Related Information General terms and conditions... F-17 SC-GU1-485... P.935~ General precautions... P.145 Sensor selection guide P.3~ Glossary of terms... P.1359~ Korea s S-mark... P.141 Conforming to EMC Directive Certified NPN output types of connector type only Recognition * Passed the U 991 Environment Test * U 611C-1 compatible, Passed the U 991 Environment Test based on SEMI S2-2. [Category applicable for semiconductor manufacturing: TWW2, Process Equipment] [Applicable standards: U 611C-1] [Additional test / evaluation standards as per intended use: U 991, SEMI S2-2] PNP output type available Timer Interference prevention ight intensity monitor MEASURE panasonic-electric-works.net/sunx Constant advances achieving significant improvement of sensing performance Automatic sensitivity setting The digital fiber sensor FX-31(P) has been modified since its production in June 24. Stable sensing over long and short periods FX-31 FX-31-HS FX-35 Even greater sensing range All models In addition to a four-chemical emitting element which suppresses changes in the light emitting element over time so that a stable level of light emission can be maintained over long periods, a APC (Auto Power Control) circuit has also been adopted afreshly. The light emitting amount can be controlled in minute degrees so that even changes occurring over very short periods can be handled, allowing stable sensing performance by suppressing deviations in light emitting amounts caused by changes in the ambient environment that could not previously be suppressed. Adoption of a double coupling lens that increases emission efficiency to its maximum limits and greatly increases sensing range. Sensing ranges with small diameter fibers and ultra-small diameter fibers, which have become very popular due to the miniaturization of chip components, have been increased by 5 % over previous values achieved with other amplifiers. Conventional fiber sensors (Without lens) Stable sensing comparison ight emitting amount Short-term stability Deviation ong-term stability Time FX-31 FX-31-HS FX-35 Three-chemical emitting element, Without APC Double coupling lens Disperses the light reduces emitting efficiency. The lens concentrates the light, greatly increasing emitting efficiency.
Digital Sensor SERIES 178 APPICATIONS Detecting the presence or absence of labels The light-emitting amount selection function can even stabilize detection of transparent labels that saturate the light-receiving level. Detecting the presence or absence of ICs on a tray You can set upper and lower limits for the threshold values using the window comparator mode and turn ON / OFF the incident light intensity within that limit. Detecting the passage of small objects The differential sensing mode will only detect rapid changes in the amount of light, which makes it possible for small objects to be detected. PHOTO PHOTO ight-emitting amount selection FX-31 FX-31-HS FX-35 If the light receiving level becomes saturated during close-range sensing or when sensing transparent or minute objects, you can adjust the light emitting amount of the sensor to stabilize sensing without needing to change the response time. Sensing that previously required the response time or fibers to be changed can now be set much more easily using this function. arge display 9999 FX-35 arge display with 4 digits (9999). With a greater difference in digit value than previous models, threshold values can be set in units of 1 digit up to maximum 9999. Threshold setting can now be done more easily and accurately. (During, ONG and U-G modes) Digit difference: Small 2.5 times previous models Previous models 4 [ight receiving level saturated] Digit difference comparison Example Digit difference between object A and object B A 4 B Digit difference: arge Actual digit difference: C Upper display limit Saturated digit difference: D FX-35 9999 ight emitting amount changed [Stable sensing] A, B, Actual digit difference: C Ultra high-speed 35 µs response FX-31-HS Ultra high-speed 35 µs response. Even small objects moving at high speeds can be sensed. In addition, at 65 µs the FX-31 standard type and FX-35 highfunction type is also twice as fast as previous models. evel 4 evel 3 evel 2 evel 1 OFF ight emitting amount can be changed without changing response time Ultra high-speed type FX-31-HS (H-SP mode) 35 μs Standard type FX-31, High-function type FX-35 (H-SP mode) 65 μs Previous model 15 μs 4 times as fast as before 35 µs MEASURE
179 Digital Sensor SERIES PHOTO PHOTO Simplified systems using new operating modes A window comparator mode and differential sensing mode have been added. These modes make it easy to carry out sensing tasks that previously required multiple sensors or involved complex threshold settings. Window comparator mode <Sensing ICs in trays> Differential sensing mode <Sensing of tiny moving objects> FX-35 MEASURE Equipped with 5 types timers Tray absent IC present Tray present OFF ON OFF Incident light intensity Upper and lower limits for threshold values can be set so that the incident light intensity can turn on and off within those ranges. Single output is used, so that only one cable is required, and no PC processing is required either. The FX-35 includes the same ON-delay / OFF-delay / ONE SHOT timer as the FX-31(-HS), as well as an ON-delay OFF-delay timer and an ON-delay ONE SHOT timer. A wide variety of timer control operations can be carried out by these fiber sensors alone. Timer period Output 1:.5 to 9,999 ms (variable) Output 2:.5 to 5 ms (variable) Incident light intensity ON-delay ower light amounts due to dust Because sensing is not possible at normal sensitivity settings, sensitivity must be reset. ON ON Sensing of only sudden changes in light amounts Only the target objects are sensed. No need to reset the sensitivity. Time chart Sensing condition OFF-delay ONE SHOT ON-delay OFF-delay ON-delay ONE SHOT T1 For -ON T1 T1 T1 T1 T1 T2 T2 T1 FX-35 Beamreceived Beaminterrupted ON OFF ON OFF ON OFF ON OFF ON OFF Even beginners can quickly learn how to use the MODE NAVI MODE NAVI uses six indicators to display the amplifier s basic operations. The current operating mode can be confirmed at a glance, so even a first time user can easily operate the amplifier without becoming confused. RUN TEACH ADJ RUN TEACH ADJ RUN TEACH ADJ RUN This is the sensing mode. Incident light level is displayed in the digital display. TEACH This mode is for setting the threshold value. ADJ In this mode, the threshold value, once set, may be fine-tuned. All models /D / D ON TIMER This mode allows the selection of output operation as either PRO ight-on or Dark-ON. /D TIMER TIMER This mode permits the choice of using or not PRO using the timer. /D PRO TIMER This mode allows the selection of further advanced functions, such as the copying of PRO individual settings and the memory functions. Easy confirming of threshold value settings FX-31 FX-31-HS FX-35 The threshold value can be confirmed by turning the jog switch even during RUN mode. Jog switch is turned eft: FX-31(-HS) Output 1 for FX-35 Right: Output 2 for FX-35 The threshold value is displayed
Digital Sensor SERIES 18 The use of only two switches makes for very simple operations Only two switches, the large jog switch and the large MODE key, are required for operation. You can operate it simply by the 3 steps shown on the right. arge MODE key Pressing the switch selects or cancels the operating mode A quick-connection cable saves wiring and work-hours Connector type One unit can be used as either a main unit or sub unit The amplifier unit can be used as either a main unit or a sub unit. This feature allows for easy mounting in the side-by-side configuration. The main and sub unit functions are distinguished only by the proper use of the main cable and the sub cable. Moreover, inventory management and maintenance is simplified. FX-35 FX-31(-HS) FX-31B/G/H Main cable (4-core) CN-74-C Sub cable (2-core) CN-72-C Main cable (3-core) CN-73-C Sub cable (1-core) CN-71-C 1 Identical part numbers eliminate the need for costly inventory management labor Main cable Sub cable arge jog switch 2 3 Moving the switch from side to side allows items to be selected All models Pressing the switch then confirms the selected setting An optical communication function allows up to *16 sensors to be adjusted simultaneously FX-31 FX-35 The optical communication function allows the data that is currently set to be copied and saved all at once for all amplifiers connected together from the right side. This greatly reduces troublesome setup tasks and makes setup much smoother.in addition, troublesome adjustment operations at times such as when replacing sensors can also be carried out easily and data can also be copied and stored Single copy & save operation for all amplifiers using the optical communication function. * Use the optical communication function for only the same types of sensors. Furthermore, the FX-31-HS is not equipped with optical communication function capability. Settings can be entered directly using numerical input All models Every function can be directly set merely by the input of a four digit code (numbers) from the code table. This convenient feature is easy to set up. In the event that settings are accidentally changed at the operating site, merely entering the correct code can restore the original settings. This results in easy and quick maintenance. Communication unit improves equipment starting up and maintenance External input unit for digital sensor FX-CH2 Teaching and changing settings can be performed by using the PC and touch panel. Various settings and switching of up to 16 units of digital fiber sensors can be accomplished at once without operating the actual sensors themselves, but via external signals, such as the PC, touch panel, and push buttons. <Main functions> Batch teaching Key lock setting Batch loading / saving of the data bank Upper communication unit for digital sensor First digit: Settings for response time and hysteresis Second digit: Settings for /D ON and display mode Fourth digit: Timer period settings Third digit: Settings for Adjust lock and timer SC-GU1-485 We now offer remote maintenance for digital sensors! The communication unit enables inputs to the digital fiber sensors (such as teaching and data bank switching) to be carried out via a PC or a personal computer, and also allows confirming of the incident light intensity an output status for the fiber sensors. This greatly improves workability during equipment starting up and maintenance. <Communicable commands> Sensor incident light intensity Sensor settings verification Sensor output status Threshold value settings, etc. FX-31 FX-35 FX-31(P) FX-35(P) PHOTO PHOTO MEASURE PC Refer to our website for details Compatible with all PCs equipped with RS-485 compatible units Refer to SC-GU1-485 pages for details RS-485 SC-GU1-485 communication
181 Digital Sensor SERIES ORDER GUIDE Quick-connection cable is not supplied with the amplifier. Please order it separately. Type Appearance Model No. Emitting element Output Standard type High-speed type FX-31 FX-31P FX-31B FX-31BP FX-31G FX-31GP FX-31H FX-31HP FX-31-HS FX-31P-HS Red ED Blue ED Green ED Infrared ED Red ED NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor NPN open-collector transistor PNP open-collector transistor Quick-connection cables Type Model No. ength CN-73-C1 1 m 3.281 ft Sub cable (1-core) Main cable (3-core) CN-73-C2 2 m 6.562 ft CN-73-C5 5 m 16.44 ft CN-71-C1 1 m 3.281 ft CN-71-C2 2 m 6.562 ft CN-71-C5 5 m 16.44 ft High-function type FX-35 FX-35P Red ED NPN open-collector transistor PNP open-collector transistor Main cable (4-core) Sub cable (2-core) CN-74-C1 CN-74-C2 CN-74-C5 CN-72-C1 CN-72-C2 CN-72-C5 1 m 3.281 ft 2 m 6.562 ft 5 m 16.44 ft 1 m 3.281 ft 2 m 6.562 ft 5 m 16.44 ft
Digital Sensor SERIES 182 ORDER GUIDE Quick-connection cables For FX-31(-HS)/B/G/H Quick-connection cable is not supplied with the amplifier. Please order it separately. Main cable Type Model No. Description CN-73-C Main cable (3-core) Sub cable (1-core) CN-73-C1 CN-73-C2 CN-73-C5 CN-71-C1 CN-71-C2 CN-71-C5 ength: 1 m 3.281 ft ength: 2 m 6.562 ft ength: 5 m 16.44 ft ength: 1 m 3.281 ft ength: 2 m 6.562 ft ength: 5 m 16.44 ft.15 mm 2 3-core cabtyre cable, with connector on one end Cable outer diameter: ø3. mm ø.118 in.15 mm 2 1-core cabtyre cable, with connector on one end Cable outer diameter: ø3. mm ø.118 in Sub cable CN-71-C For FX-35 Quick-connection cable is not supplied with the amplifier. Please order it separately. Type Model No. Description Main cable (4-core) Sub cable (2-core) CN-74-C1 CN-74-C2 CN-74-C5 CN-72-C1 CN-72-C2 CN-72-C5 ength: 1 m 3.281 ft ength: 2 m 6.562 ft ength: 5 m 16.44 ft ength: 1 m 3.281 ft ength: 2 m 6.562 ft ength: 5 m 16.44 ft.15 mm 2 4-core cabtyre cable, with connector on one end Cable outer diameter: ø3. mm ø.118 in.15 mm 2 2-core cabtyre cable, with connector on one end Cable outer diameter: ø3. mm ø.118 in Main cable CN-74-C Sub cable CN-72-C End plates End plates are not supplied with the amplifier. Please order them separately when the amplifiers are mounted in cascade. Appearance Model No. Description MS-DIN-E When cascading multiple amplifiers, or when it moves depending on the way it is installed on a DIN rail, these end plates clamp amplifiers into place on both sides. Make sure to use end plates when cascading multiple amplifiers together. Two pcs. per set Designation Model No. Description Amplifier mounting bracket amplifier protection seal MS-DIN-2 FX-MB1 Mounting bracket for amplifier 1 sets of 2 communication window seals and 1 connector seal Communication window seal: It prevents malfunction due to transmission signal from another amplifier, as well as, prevents effect on another amplifier. Connector seal: It prevents contact of any metal, etc., with the pins of the quickconnection cable. Note: amplifier protection seals are supplied with the FX-31(P) and FX-35(P). Amplifier mounting bracket MS-DIN-2 amplifier protection seal FX-MB1 Communication window seal Connector seal
183 Digital Sensor SERIES IST OF S FX-31 / FX-35 (Red ED type) sensing range (Note 1) Thru-beam type (one pair set) are listed in alphabetic order. Refer to p.5~ for details of each fiber. Model No. The FX-35 and FX-31(-HS) have different sensing modes. FX-35: H-SP, ST,,, ONG, U-G (no S-D mode) FX-31(-HS): S-D, H-SP (Note 1), ST,, ONG (no or U-G mode) Sensing range (mm in) (Note 2) Red ED U-G ONG ST H-SP S-D Dimensions FT-3 45 17.717 31 12.25 21 8.268 15 5.96 11 4.331 6 2.362 6 2.362 P.9 FT-31 44 17.323 29 11.417 2 7.874 142 5.591 15 4.134 58 2.283 49 1.929 P.9 FT-4 1,3 51.181 9 35.433 6 23.622 45 17.717 33 12.992 18 7.87 18 7.87 P.9 FT-41 1, 39.37 78 3.79 5 19.685 4 15.748 28 11.24 15 5.96 13 5.118 P.9 FT-42 1,1 43.37 8 31.496 55 21.654 4 15.748 285 11.22 16 6.299 15 5.96 P.9 FT-A8 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3,3 129.921 1,5 59.55 1,1 43.37 1,8 42.52 75 29.528 P.9 FT-A3 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3, 118.11 3,5 137.795 (Note 3) P.9 FT-AFM2 85 33.465 65 25.591 38 14.961 33 12.992 22 8.661 1 3.937 115 4.528 P.9 FT-AFM2E 8 31.496 59 23.228 35 13.78 29 11.417 2 7.874 9 3.543 1 3.937 P.9 FT-B8 1,6 62.992 1,1 43.37 7 27.559 53 2.866 4 15.748 2 7.874 18 7.87 P.9 FT-E12 2.787 18.79 13.512 1.394 8.315 3.118 3.118 P.91 FT-E13 2.787 13.512 9.354 6.236 5.197 2.79 2.79 P.91 FT-E22 13 5.118 8 3.15 6 2.362 5 1.969 36 1.417 18.79 15.591 P.91 FT-E23 95 3.74 65 2.559 42 1.654 31 1.22 22.866 12.472 12.472 P.91 FT-FM2 1, 39.37 78 3.79 5 19.685 4 15.748 28 11.24 15 5.96 13 5.118 P.91 FT-FM2S 1, 39.37 78 3.79 5 19.685 4 15.748 28 11.24 15 5.96 13 5.118 P.91 FT-FM2S4 1, 39.37 78 3.79 5 19.685 4 15.748 28 11.24 15 5.96 13 5.118 P.91 FT-FM1 19,5 767.717 (Note 4) 19,5 767.717 (Note 4) 19,5 767.717 (Note 4) 14, 551.18 1, 393.7 3,5 137.795 3,8 149.66 P.91 FT-H13-FM2 1,2 47.244 88 34.646 55 21.654 44 17.323 3 11.811 15 5.96 155 6.12 P.91 FT-H2-J2-S (Note 5) 53 2.866 39 15.354 225 8.858 2 7.874 14 5.512 6 2.362 6 2.362 P.92 FT-H2-J3-S (Note 5) 53 2.866 39 15.354 225 8.858 2 7.874 14 5.512 6 2.362 6 2.362 P.92 FT-H2-J5-S (Note 5) 53 2.866 39 15.354 225 8.858 2 7.874 14 5.512 6 2.362 6 2.362 P.92 FT-H2-M1 75 29.528 55 21.654 32 12.598 28 11.24 2 7.874 85 3.346 9 3.543 P.92 FT-H2-VJ5-S (Note 5) 84 33.71 55 21.654 37 14.567 28 11.24 2 7.874 9 3.543 9 3.543 P.92 FT-H2-VJ8-S (Note 5) 84 33.71 55 21.654 37 14.567 28 11.24 2 7.874 9 3.543 9 3.543 P.92 FT-H2W-M1 42 16.535 31 12.25 18 7.87 14 5.512 1 3.937 4 1.575 5 1.969 P.92 FT-H3-M1V-S (Note 6) 35 13.78 25 9.843 15 5.96 125 4.921 9 3.543 5 1.969 4 1.575 P.92 FT-H35-M2 75 29.528 55 21.654 33 12.992 28 11.24 2 7.874 85 3.346 9 3.543 P.92 FT-H35-M2S6 75 29.528 55 21.654 33 12.992 28 11.24 2 7.874 85 3.346 9 3.543 P.92 FT-H8Y 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 1,8 7.866 1,35 53.15 9 35.433 45 17.717 48 18.898 P.92 FT-K8 3, 118.11 2, 78.74 1,5 59.55 1, 39.37 8 31.496 3 11.811 35 13.78 P.93 FT-KV1 6 23.622 5 19.685 3 11.811 25 9.843 18 7.87 9 3.543 1 3.937 P.93 FT-KV8 3, 118.11 2, 78.74 1,5 59.55 1, 39.37 8 31.496 3 11.811 35 13.78 P.93 FT-8Y 3,5 137.795 3,5 137.795 2, 78.74 1,5 59.55 1, 39.37 5 19.685 53 2.866 P.93 FT-NFM2 4 15.748 27 1.63 2 7.874 14 5.512 1 3.937 55 2.165 49 1.929 P.93 FT-NFM2S 4 15.748 27 1.63 2 7.874 14 5.512 1 3.937 55 2.165 49 1.929 P.93 FT-NFM2S4 4 15.748 27 1.63 2 7.874 14 5.512 1 3.937 55 2.165 49 1.929 P.93 FT-P2 35 13.78 28 11.24 16 6.299 12 4.724 9 3.543 4 1.575 42 1.654 P.93 FT-P4 35 13.78 25 9.843 15 5.96 1 3.937 75 2.953 3 1.181 35 1.378 P.93 FT-P6 55 21.654 4 15.748 25 9.843 19 7.48 14 5.512 7 2.756 8 3.15 P.93 Notes: 1) Refer to p.35~ for the sensing ranges for the FX-31-HS in H-SP mode. 2) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 3) The fiber cable length practically limits the sensing range to 3,5 mm 137.795 in long. 4) The fiber cable length practically limits the sensing range to 19,5 mm 767.717 in long. 5) Heat-resistant joint fibers and ordinary-temperature fibers (FT-FM2) are sold as a set. 6) Sold as a set comprising vacuum type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8).
Digital Sensor SERIES 184 IST OF S FX-31 / FX-35 (Red ED type) sensing range (Note 1) Thru-beam type (one pair set) are listed in alphabetic order. Refer to p.5~ for details of each fiber. Model No. The FX-35 and FX-31(-HS) have different sensing modes. FX-35: H-SP, ST,,, ONG, U-G (no S-D mode) FX-31(-HS): S-D, H-SP (Note 1), ST,, ONG (no or U-G mode) Sensing range (mm in) (Note 2) Red ED U-G ONG ST H-SP S-D Dimensions FT-P8 9 35.433 65 25.591 4 15.748 32 12.598 23 9.55 1 3.937 11 4.331 P.93 FT-P81X 9 35.433 65 25.591 38 14.961 32 12.598 23 9.55 1 3.937 11 4.331 P.94 FT-PS1 1 3.937 8 3.15 5 1.969 4 1.575 3 1.181 13.512 17.669 P.93 FT-R8 74 29.134 53 2.866 32 12.598 23 9.55 15 5.96 75 2.953 8 3.15 P.94 FT-S2 45 17.717 31 12.25 21 8.268 15 5.96 11 4.331 6 2.362 6 2.362 P.94 FT-S21 44 17.323 29 11.417 2 7.874 142 5.591 15 4.134 58 2.283 49 1.929 P.94 FT-S3 1,3 51.181 9 35.433 6 23.622 45 17.717 33 12.992 18 7.87 18 7.87 P.94 FT-SFM2 1, 39.37 78 3.79 5 19.685 4 15.748 28 11.24 15 5.96 13 5.118 P.94 FT-SFM2 2, 78.74 1,6 62.992 82 32.283 8 31.496 58 22.835 17 6.693 28 11.24 P.94 FT-SFM2SV2 55 21.654 4 15.748 24 9.449 2 7.874 14 5.512 65 2.559 7 2.756 P.94 FT-SNFM2 4 15.748 27 1.63 2 7.874 14 5.512 1 3.937 55 2.165 49 1.929 P.95 FT-T8 1, 39.37 78 3.79 5 19.685 4 15.748 28 11.24 15 5.96 13 5.118 P.95 FT-V1 2,35 92.52 2, 78.74 1,4 55.118 1, 39.37 8 31.496 34 13.386 35 13.78 P.95 FT-V22 41 16.142 39 15.354 22 8.661 18 7.87 125 4.921 6 2.362 63 2.48 P.95 FT-V41 22 8.661 175 6.89 1 3.937 8 3.15 6 2.362 25.984 27 1.63 P.95 FT-V8Y 1, 39.37 8 31.496 5 19.685 4 15.748 28 11.24 12 4.724 14 5.512 P.95 FT-W4 22 8.661 16 6.299 1 3.937 8 3.15 55 2.165 25.984 28 1.12 P.95 FT-W8 75 29.528 57 22.441 35 13.78 29 11.417 2 7.874 9 3.543 1 3.937 P.95 FT-WA8 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3,3 129.921 1,5 59.55 1,1 43.37 1,8 42.52 75 29.528 P.95 FT-WA3 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3,5 137.795 (Note 3) 3, 118.11 3,5 137.795 (Note 3) P.95 FT-WKV8 2,2 86.614 1,7 66.929 1, 39.37 7 27.559 6 23.622 28 11.24 3 11.811 P.96 FT-WR8 75 29.528 57 22.441 35 13.78 29 11.417 2 7.874 9 3.543 1 3.937 P.96 FT-WR8 1,5 59.55 1,2 47.244 75 29.528 6 23.622 42 16.535 2 7.874 21 8.268 P.96 FT-WS3 78 3.79 57 22.441 34 13.386 29 11.417 2 7.874 9 3.543 1 3.937 P.96 FT-WS4 22 8.661 16 6.299 1 3.937 8 3.15 55 2.165 25.984 28 1.12 P.96 FT-WS8 75 29.528 57 22.441 35 13.78 29 11.417 2 7.874 9 3.543 1 3.937 P.96 FT-WS8 1,5 59.55 1,2 47.244 75 29.528 6 23.622 42 16.535 2 7.874 21 8.268 P.96 FT-WV42 12 4.724 9 3.543 55 2.165 4 1.575 3 1.181 13.512 15.591 P.96 FT-WZ4 3 11.811 2 7.874 14 5.512 1 3.937 7 2.756 4 1.575 4 1.575 P.96 FT-WZ4HB 22 8.661 15 5.96 15 4.134 75 2.953 5 1.969 3 1.181 3 1.181 P.97 FT-WZ7 66 25.984 44 17.323 38 12.126 22 8.661 15 5.96 8 3.15 8 3.15 P.97 FT-WZ7HB 87 34.252 58 22.835 46 15.984 29 11.417 21 8.268 11 4.331 11 4.331 P.97 FT-WZ8 95 37.42 7 27.559 42 16.535 33 12.992 24 9.449 1 3.937 12 4.724 P.97 FT-WZ8E 2,1 82.677 1,5 59.55 95 37.42 7 27.559 5 19.685 2 7.874 21 8.268 P.97 FT-WZ8H 3,5 137.795 2,5 98.425 1,6 62.992 1,2 47.244 85 33.465 4 15.748 41 16.142 P.97 FT-Z8 1,1 43.37 8 31.496 5 19.685 4 15.748 3 11.811 12 4.724 14 5.512 P.97 FT-Z8E 1,85 72.835 1,6 62.992 95 37.42 8 31.496 6 23.622 25 9.843 28 11.24 P.97 FT-Z8H 3,1 122.47 2,7 16.299 1,55 61.24 1,4 55.118 1, 39.37 42 16.535 49 19.291 P.97 FT-Z82Y 3,5 137.795 3,5 137.795 3, 118.11 1,5 59.55 1, 39.37 5 19.685 53 2.866 P.97 Notes: 1) Refer to p.35~ for the sensing ranges for the FX-31-HS in H-SP mode. 2) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 3) The fiber cable length practically limits the sensing range to 3,5 mm 137.795 in long.
185 Digital Sensor SERIES IST OF S FX-31 / FX-35 (Red ED type) sensing range (Note 1) Retroreflective type are listed in alphabetic order. Refer to p.5~ for details of each fiber. Model No. The FX-35 and FX-31(-HS) have different sensing modes. FX-35: H-SP, ST,,, ONG, U-G (no S-D mode) FX-31(-HS): S-D, H-SP (Note 1), ST,, ONG (no or U-G mode) Sensing range (mm in) (Note 2, 3) Red ED U-G ONG ST H-SP S-D Dimensions FR-KV1 15 to 37.591 to 14.567 15 to 33.591 to 12.992 15 to 24.591 to 9.449 15 to 21.591 to 8.268 15 to 17.591 to 6.693 15 to 8.591 to 3.15 15 to 9.591 to 3.543 P.98 FR-KZ21 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 P.98 FR-KZ21E 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 2 to 2.787 to 7.874 P.98 FR-WKZ11 1 to 91 3.937 to 35.827 1 to 73 3.937 to 28.74 1 to 6 3.937 to 23.622 1 to 52 3.937 to 2.472 1 to 46 3.937 to 18.11 P.98 Notes: 1) Refer to p.35~ for the sensing ranges for the FX-31-HS in H-SP mode. 2) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. The sensing range of FR-WKZ11 is specified for the RF-13. The sensing range of FR-KZ21 and FR-KZ21E is specified for the attached reflector RF-3. The sensing range of FR-KV1 is specified for the attached reflector. 3) The sensing range of retroreflective type is the possible setting range for the attached reflector. The fiber can detect an object less than setting range for the reflector. However, note that if there are any white or highly-reflective surfaces near the fiber, reflected incident light may affect the fiber. If this occurs, adjust the threshold value of the amplifier unit before use. FX-31 / FX-35 (Red ED type) sensing range (Note 1) Reflective type are listed in alphabetic order. Refer to p.5~ for details of each fiber. The FX-35 and FX-31(-HS) have different sensing modes. FX-35: H-SP, ST,,, ONG, U-G (no S-D mode) FX-31(-HS): S-D, H-SP (Note 1), ST,, ONG (no or U-G mode) Sensing range (mm in) (Note 2, 3) Model No. Red ED Dimensions U-G ONG ST H-SP S-D FD-3 17 6.693 11 4.331 7 2.756 5 1.969 4 1.575 2.787 18.79 P.99 FD-31 15 5.96 95 3.74 63 2.48 45 1.772 35 1.378 17.669 16.63 P.99 FD-4 17 6.693 11 4.331 7 2.756 5 1.969 4 1.575 2.787 18.79 P.99 FD-41 15 5.96 95 3.74 63 2.48 45 1.772 35 1.378 17.669 16.63 P.99 FD-6 5 19.685 35 13.78 24 9.449 16 6.299 13 5.118 7 2.756 7 2.756 P.99 FD-61 44 17.323 32 12.598 25 8.71 145 5.79 15 4.134 65 2.559 6 2.362 P.99 FD-A15 23 9.55 2 7.874 15 5.96 15 5.96 1 3.937 45 1.772 5 1.969 P.99 FD-AFM2 29 11.417 22 8.661 135 5.315 11 4.331 78 3.71 35 1.378 39 1.535 P.99 FD-AFM2E 29 11.417 22 8.661 135 5.315 11 4.331 78 3.71 35 1.378 39 1.535 P.99 FD-B8 6 23.622 48 18.898 28 11.24 22 8.661 16 6.299 85 3.346 75 2.953 P.99 FD-E12 15.591 11.433 8.315 6.236 4.157 2.79 1.39 P.1 FD-E22 65 2.559 45 1.772 28 1.12 23.96 17.669 8.315 7.276 P.1 FD-EG1 5 1.969 38 1.496 25.984 18.79 14.551 5.197 6.236 P.1 FD-EG2 4 1.575 25.984 14.551 12.472 9.354 3.118 5.197 P.1 FD-EG3 2.787 15.591 9.354 8.315 5.197 2.5.98 3.118 P.1 FD-EN5S1 6.5.256 5.197 3.118 3.118 2.79 Cannot use Cannot use P.1 FD-ENM1S1 5 1.969 38 1.496 2.787 18.79 14.551 5.197 6.236 P.1 Applicable pipe diameter: Outer dia. ø6 to ø26 mm ø.236 to ø1.24 in transparent pipe FD-F4 [P (fluorine resin) or equivalently transparent pipe, wall thickness 1 mm.39 in] P.1 Applicable pipe diameter: Outer dia. ø6 to ø26 mm ø.236 to ø1.24 in transparent pipe FD-F41 [PVC (vinyl chloride), fluorine resin, polycarbonate, acrylic, glass, wall thickness 1 to 3 mm.39 to.118 in] P.1 ø4 mm ø.157 in form Protective tube: fluorine resin, length 5 mm 19.685 in (cuttable) FD-F41Y iquid surface not contacted: Beam received, iquid surface contacted: Beam interrupted P.11 FD-F8Y P.11 Applicable pipe diameter: Outer dia. ø8 mm ø.315 in or more transparent pipe (When used with the tying bands: ø8 to ø8 mm ø.315 to ø3.15 in) [P (fluorine resin), including translucent] FD-9 iquid absent: Beam received, iquid present: Beam interrupted P.11 FD-FM2 41 16.142 31 12.25 2 7.874 14 5.512 1 3.937 55 2.165 47 1.85 P.11 FD-FM2S 37 14.567 27 1.63 17 6.693 11 4.331 85 3.346 45 1.772 39 1.535 P.11 FD-FM2S4 37 14.567 27 1.63 17 6.693 11 4.331 85 3.346 45 1.772 39 1.535 P.11 FD-G4 15 5.96 11 4.331 65 2.559 55 2.165 42 1.654 15.591 19.748 P.11 FD-G6 15 5.96 11 4.331 65 2.559 55 2.165 42 1.654 15.591 19.748 P.12 FD-G6X 15 5.96 9 3.543 48 1.89 45 1.772 35 1.378 12.472 2.787 P.12 FD-G4 15 5.96 11 4.331 65 2.559 55 2.165 42 1.654 15.591 19.748 P.11 FD-G6 41 16.142 31 12.25 2 7.874 14 5.512 1 3.937 55 2.165 47 1.85 P.12 FD-H13-FM2 41 16.142 31 12.25 2 7.874 14 5.512 1 3.937 55 2.165 47 1.85 P.12 FD-H18-31 to 2 to.787 to 15 to.591 to 1 to.394 to 1 to.394 1 to 8.39 to.315 Cannot use 2 to 6.79 to.236 P.12 Notes: 1) Refer to p.35~ for the sensing ranges for the FX-31-HS in H-SP mode. 2) The standard sensing objects of the sensing ranges vary depending on the fibers. 3) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut.
Digital Sensor SERIES 186 IST OF S FX-31 / FX-35 (Red ED type) sensing range (Note 1) Reflective type are listed in alphabetic order. Refer to p.5~ for details of each fiber. Model No. Sensing range (mm in) (Note 2, 3) Red ED U-G ONG ST H-SP S-D Dimensions FD-H2-21 3 11.811 27 1.63 15 5.96 14 5.512 1 3.937 35 1.378 47 1.85 P.12 FD-H2-M1 3 11.811 27 1.63 15 5.96 14 5.512 1 3.937 35 1.378 47 1.85 P.12 FD-H25-43 3 to 28.118 to 1.12 3 to 25.118 to.984 4 to 23.157 to.96 4 to 2.118 to.787 4 to 19.118 to.748 4 to 16.118 to.63 4 to 16.118 to.63 P.13 FD-H25-45 5 to 42.197 to 1.654 6 to 41.236 to 1.614 6 to 4.236 to 1.575 7 to 38.276 to 1.496 P.13 FD-H3-KZ1V-S (Note 4) 2 to 3.787 to 11.811 2 to 2.787 to 7.874 2 to 15.787 to 5.96 25 to 13.984 to 5.118 3 to 1 1.181 to 3.937 Cannot use Cannot use P.13 FD-H3-32 to 2 to.787 to 15 to.591 to 1 to.394 to 1 to.394 1 to 8.39 to.315 Cannot use 2 to 6.79 to.236 P.13 FD-H3-32V-S (Note 4) to 11 to.433 to 8 to.315 1.5 to 6.59 to.236 1.5 to 5.59 to.197 2 to 4.79 to.157 Cannot use Cannot use P.13 FD-H35-2S 19 7.48 16 6.299 8 3.15 8 3.15 57 2.244 2.787 26 1.24 P.14 FD-H35-M2 3 11.811 27 1.63 15 5.96 14 5.512 1 3.937 35 1.378 47 1.85 P.14 FD-H35-M2S6 3 11.811 27 1.63 15 5.96 14 5.512 1 3.937 35 1.378 47 1.85 P.14 ø4 mm ø.157 in form Protective tube: fluorine resin, length:5 mm 19.685 in (allowable cutting) FD-HF4Y iquid surface not contacted: Beam received, iquid surface contacted: Beam interrupted P.14 FD-4 FD-41 2 to 2.79 to.787 (Convergent point 6.236) 2.5 to 18.98 to.79 (Convergent point 6.236) 4 to 12.157 to.472 (Convergent point 6.236) 4 to 12.157 to.472 (Convergent point 6.236) 4.5 to 11.177 to.433 (Convergent point 6.236) 5 to 8.5.197 to.335 (Convergent point 6.236) 4.8 to 9.5.189 to.374 (Convergent point 6.236) 2 to 19.79 to.748 2.5 to 18.98 to.79 3 to 16.118 to.63 3 to 16.118 to.63 3.5 to 15.138 to.591 (Convergent point 8.315) (Convergent point 8.315) (Convergent point 8.315) (Convergent point 8.315) (Convergent point 8.315) Cannot use Cannot use P.14 FD-43 to 23 to.96 P.14 FD-44 to 8.2 to.323 to 7 to.276 to 6.5 to.256 to 6 to.236 to 5.7 to.224 to 5 to.197 to 5.2 to.25 P.14 FD-44S to 4.7 to.185 to 4.5 to.177 to 4 to.157 to 4 to.157 to 3.8 to.15 to 3 to.118 to 3.5 to.138 P.14 FD-45 to 5 to 1.969 to 36 to 1.417 to 33 to 1.299 to 3 to 1.181 to 3 to 1.181 to 15 to.591 to 21 to.827 P.14 FD-45A 1 to 33.394 to 1.299 (Note 5) 1 to 33.394 to 1.299 (Note 5) 1 to 32.394 to 1.26 (Note 5) 1 to 32.394 to 1.26 (Note 5) 1 to 32.394 to 1.26 (Note 5) 13 to 18.512 to.79 (Note 5) 13 to 18.512 to.79 (Note 5) FD-46 12 to 5.472 to 1.969 12.5 to 37.5.492 to 1.476 15 to 36.591 to 1.417 15 to 35.591 to 1.378 16 to 29.63 to 1.142 Cannot use Cannot use P.15 FD-47 3 1.181 3 1.181 3 1.181 3 1.181 1 to 28.39 to 1.12 2 to 27.79 to 1.63 2 to 27.79 to 1.63 P.15 FD-NFM2 14 5.512 9 3.543 6 2.362 45 1.772 35 1.378 16.63 16.63 P.15 FD-NFM2S 14 5.512 9 3.543 6 2.362 45 1.772 35 1.378 16.63 16.63 P.15 FD-NFM2S4 14 5.512 9 3.543 6 2.362 45 1.772 35 1.378 16.63 16.63 P.15 FD-P2 8 3.15 5 1.969 3 1.181 25.984 19.748 7.5.295 9.354 P.15 FD-P4 5 1.969 36 1.417 2.787 18.79 14.551 5.5.217 6.236 P.15 FD-P5 13 5.118 9 3.543 55 2.165 45 1.772 3 1.181 13.512 16.63 P.15 FD-P6 13 5.118 9 3.543 55 2.165 45 1.772 3 1.181 13.512 16.63 P.15 FD-P8 3 11.811 22 8.661 13 5.118 1 3.937 7 2.756 3 1.181 35 1.378 P.15 FD-P81X 27 1.63 185 7.283 1 3.937 8 3.15 6 2.362 3 1.181 35 1.378 P.16 FD-R8 24 9.449 185 7.283 11 4.331 85 3.346 6 2.362 25.984 3 1.181 P.16 FD-S3 17 6.693 11 4.331 7 2.756 5 1.969 4 1.575 2.787 18.79 P.16 FD-S31 15 5.96 95 3.74 63 2.48 45 1.772 35 1.378 17.669 16.63 P.16 FD-S8 37 14.567 27 1.63 17 6.693 11 4.331 85 3.346 45 1.772 39 1.535 P.16 FD-SFM2SV2 17 6.693 1 3.937 55 2.165 45 1.772 32 1.26 15.591 16.63 P.16 FD-SNFM2 14 5.512 9 3.543 6 2.362 45 1.772 35 1.378 16.63 16.63 P.16 FD-T4 14 5.512 9 3.543 6 2.362 45 1.772 35 1.378 16.63 16.63 P.16 FD-T8 37 14.567 27 1.63 17 6.693 11 4.331 85 3.346 45 1.772 39 1.535 P.16 FD-V41 8 3.15 55 2.165 3 1.181 25.984 17.669 8.315 9.354 P.16 FD-W8 25 9.843 19 7.48 11 4.331 9 3.543 6 2.362 25.984 32 1.26 P.17 FD-W44 4 1.575 3 1.181 18.79 15.591 12.472 4.5.177 5.197 P.17 FD-WG4 85 3.346 65 2.559 37 1.457 32 1.26 25.984 1.394 11.433 P.17 FD-WKZ1 2 to 66.787 to 25.984 2 to 48.787 to 18.898 2 to 3.787 to 11.811 2 to 23.787 to 9.55 2 to 17.787 to 6.693 25 to 9.984 to 3.543 25 to 1.984 to 3.937 P.17 FD-W41 6.5 to 14.5.256 to.571 (Convergent point 8.315) 6.5 to 14.256 to.551 (Convergent point 8.315) 7 to 14.276 to.551 (Convergent point 8.315) The FX-35 and FX-31(-HS) have different sensing modes. FX-35: H-SP, ST,,, ONG, U-G (no S-D mode) FX-31(-HS): S-D, H-SP (Note 1), ST,, ONG (no or U-G mode) 7 to 12.276 to.472 (Convergent point 8.315) P.14 P.15 7.5 to 12.295 to.472 (Convergent point 8.315) Cannot use Cannot use P.17 FD-W48.5 to 8.5.2 to.335.5 to 7.5.2 to.295 1 to 6.5.39 to.256 1 to 5.5.39 to.217 1 to 5.39 to.197 Cannot use Cannot use P.17 FD-WS8 25 9.843 19 7.48 11 4.331 9 3.543 6 2.362 25.984 32 1.26 P.17 FD-WSG4 85 3.346 65 2.559 37 1.457 32 1.26 25.984 1.394 11.433 P.17 FD-WT4 4 1.575 3 1.181 18.79 15.591 12.472 4.5.177 5.197 P.17 FD-WT8 25 9.843 19 7.48 11 4.331 9 3.543 6 2.362 25.984 32 1.26 P.17 FD-WV42 2.787 15.591 8.5.335 7.276 5.197 Cannot use Cannot use P.18 FD-WZ4 1 to 5.39 to 1.969 1.5 to 34.59 to 1.339 2 to 24.79 to.945 3 to 17.118 to.669 3 to 1.118 to.394 P.18 FD-WZ4HB 1 to 7.39 to 2.756 1 to 46.39 to 1.811 1 to 32.2.39 to 1.268 2.5 to 23.98 to.96 2.5 to 15.98 to.591 3 to 7.118 to.276 3 to 7.118 to.276 P.18 FD-WZ7 2 7.874 12 4.724 1 to 84.39 to 3.37 1 to 6.39 to 2.362 1.5 to 35.59 to 1.378 2.5 to 18.98 to.79 2.5 to 18.98 to.79 P.18 FD-WZ7HB.5 to 27.2 to 1.63.5 to 18.2 to 7.87 1 to 126.39 to 4.961 1 to 9.39 to 3.543 1 to 7.39 to 2.756 1 to 35.39 to 1.378 1 to 35.39 to 1.378 P.18 Notes: 1) Refer to p.35~ for the sensing ranges for the FX-31-HS in H-SP mode. 2) The standard sensing objects of the sensing ranges vary depending on the fibers. 3) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 4) Sold as a set comprising vacuum type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8). 5) Sensing distance varies depending on the sensing object s inclination.
187 Digital Sensor SERIES SENSING RANGE OF BUE ED / GREEN ED / INFRARED ED Thru-beam type (One pair set) are listed in alphabetic order. Refer to p.5~ for details of each fiber. Sensing range (mm in) (Note 1) Model No. FX-31B FX-31G FX-31H (Note 2) Dimensions ONG ST ONG ST ONG ST FT-3 55 2.165 28 1.12 18.79 28 1.12 13.512 9.354 25.984 13.512 9.354 P.9 FT-31 5 1.969 25.984 16.63 24.945 12.472 8.315 23.96 11.433 8.315 P.9 FT-4 155 6.12 76 2.992 45 1.772 9 3.543 4 1.575 26 1.24 8 3.15 43 1.693 27 1.63 P.9 FT-41 15 5.96 75 2.953 4 1.575 7 2.756 35 1.378 24.945 5 1.969 25.984 18.79 P.9 FT-42 15 5.96 75 2.953 4 1.575 8 3.15 35 1.378 24.945 75 2.953 4 1.575 25.984 P.9 FT-A8 6 23.622 3 11.811 22 8.661 3 11.811 15 5.96 11 4.331 22 8.661 11 4.331 8 3.15 P.9 FT-A3 2,4 94.488 1,2 47.244 7 27.559 1,2 47.244 6 23.622 35 13.78 8 31.496 4 15.748 24 9.449 P.9 FT-AFM2 12 4.724 6 2.362 4 1.575 6 2.362 3 1.181 2.787 48 1.89 24.945 18.79 P.9 FT-AFM2E 12 4.724 6 2.362 4 1.575 6 2.362 3 1.181 2.787 48 1.89 24.945 18.79 P.9 FT-B8 22 8.661 11 4.331 75 2.953 11 4.331 55 2.165 4 1.575 1 3.937 5 1.969 3 1.181 P.9 FT-E12 3.118 2.79 1.39 1.39 4.157 2.79 1.5.59 P.91 FT-E13 2.79 1.39 1.39 2.79 1.39 P.91 FT-E22 14.551 7.276 4.157 6.236 3.118 2.79 1.394 5.197 3.118 P.91 FT-E23 8.315 4.157 3.118 4.157 2.79 1.39 1.394 5.197 3.118 P.91 FT-FM2 15 5.96 75 2.953 4 1.575 7 2.756 35 1.378 24.945 5 1.969 25.984 18.79 P.91 FT-FM2S 15 5.96 75 2.953 4 1.575 7 2.756 35 1.378 24.945 5 1.969 25.984 18.79 P.91 FT-FM2S4 15 5.96 75 2.953 4 1.575 7 2.756 35 1.378 24.945 5 1.969 25.984 18.79 P.91 FT-FM1 5,4 212.598 2,7 16.299 1,9 74.83 2,8 11.236 1,4 55.118 1, 39.37 2,4 94.488 (Note 3) 1,2 47.244 (Note 3) 9 35.433 (Note 3) P.91 FT-H13-FM2 72 2.835 36 1.417 26 1.24 32 1.26 16.63 1.394 7 2.756 35 1.378 25.984 P.91 FT-H2-J2-S (Note 4) 6 2.362 2.787 35 1.378 2.787 P.92 FT-H2-J3-S (Note 4) 6 2.362 2.787 35 1.378 2.787 P.92 FT-H2-J5-S (Note 4) 6 2.362 2.787 35 1.378 2.787 P.92 FT-H2-M1 1 3.937 5 1.969 35 1.378 5 1.969 25.984 18.79 55 21.654 28 11.24 16 6.299 P.92 FT-H2-VJ5-S (Note 4) 85 3.346 3 1.181 5 1.969 3 1.181 P.92 FT-H2-VJ8-S (Note 4) 85 3.346 3 1.181 5 1.969 3 1.181 P.92 FT-H2W-M1 44 1.732 22.866 14.551 22.866 11.433 7.276 22 8.661 1 3.937 7 2.756 P.92 FT-H3-M1V-S (Note 5) 4 1.575 2.787 2.787 2.787 P.92 FT-H35-M2 1 3.937 5 1.969 35 1.378 5 1.969 25.984 18.79 55 21.654 28 11.24 16 6.299 P.92 FT-H35-M2S6 1 3.937 5 1.969 35 1.378 5 1.969 25.984 18.79 55 21.654 28 11.24 16 6.299 P.92 FT-H8Y 8 3.15 4 1.575 25.984 11 4.331 55 2.165 4 1.575 1,1 43.37 55 21.654 35 13.78 P.92 FT-K8 4 15.748 2 7.874 13 5.118 2 7.874 1 3.937 65 2.559 15 5.96 75 2.953 4 1.575 P.93 FT-KV1 8 3.15 35 1.378 1.394 P.93 FT-KV8 4 15.748 2 7.874 13 5.118 2 7.874 1 3.937 65 2.559 15 5.96 75 2.953 4 1.575 P.93 FT-8Y 16 6.299 8 3.15 5 1.969 16 6.299 8 3.15 5 1.969 4 15.748 2 7.874 15 5.96 P.93 FT-NFM2 5 1.969 25.984 16.63 24.945 12.472 8.315 16.63 8.315 5.197 P.93 FT-NFM2S 5 1.969 25.984 16.63 24.945 12.472 8.315 16.63 8.315 5.197 P.93 FT-NFM2S4 5 1.969 25.984 16.63 24.945 12.472 8.315 16.63 8.315 5.197 P.93 FT-P2 36 1.417 18.79 14.551 2.787 1.394 8.315 18.79 9.354 7.276 P.93 FT-P4 32 1.26 13.512 12.472 18.79 9.354 7.276 14.551 7.276 5.197 P.93 FT-P6 5 1.969 25.984 18.79 26 1.24 13.512 8.315 2.787 1.394 7.276 P.93 Notes: 1) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 2) Because infrared types are easily affected by humidity, please ask assistance when using them in a humid environment or in an environment with varying humidity. 3) Sensing range when fiber length is 2 m 6.562 ft. When fiber length is 1 m 32.81 ft, the beam attenuates and cannot be used. 4) Heat-resistant joint fibers and ordinary-temperature fibers (FT-FM2) are sold as a set. 5) Sold as a set comprising vacuum type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8).
Digital Sensor SERIES 188 SENSING RANGE OF BUE ED / GREEN ED / INFRARED ED Thru-beam type (One pair set) are listed in alphabetic order. Refer to p.5~ for details of each fiber. Model No. Sensing range (mm in) (Note 1) FX-31B FX-31G FX-31H (Note 2) ONG ST ONG ST ONG ST FT-P8 13 5.118 65 2.559 45 1.772 7 2.756 35 1.378 25.984 56 2.25 28 1.12 2.787 P.93 FT-P81X 13 5.118 64 2.52 45 1.772 64 2.52 32 1.26 25.984 56 2.25 28 1.12 2.787 P.94 FT-PS1 14.551 7.276 4.157 6.236 3.118 2.79 14.551 7.276 4.157 P.93 FT-R8 85 3.346 42 1.654 28 1.12 44 1.732 22.866 16.63 32 1.26 16.63 12.472 P.94 FT-S2 55 2.165 28 1.12 18.79 28 1.12 13.512 9.354 25.984 13.512 9.354 P.94 FT-S21 5 1.969 25.984 16.63 24.945 12.472 8.315 23.96 11.433 8.315 P.94 FT-S3 155 6.12 76 2.992 45 1.772 9 3.543 4 1.575 26 1.24 8 3.15 43 1.693 27 1.63 P.94 FT-SFM2 15 5.96 75 2.953 4 1.575 7 2.756 35 1.378 24.945 5 1.969 25.984 18.79 P.94 FT-SFM2 4 15.748 2 7.874 13 5.118 2 7.874 1 3.937 65 2.559 155 6.12 77 3.31 55 2.165 P.94 FT-SFM2SV2 8 3.15 4 1.575 28 1.12 4 1.575 2.787 14.551 3 1.181 15.591 12.472 P.94 FT-SNFM2 5 1.969 25.984 16.63 24.945 12.472 8.315 16.63 8.315 5.197 P.95 FT-T8 15 5.96 75 2.953 4 1.575 7 2.756 35 1.378 24.945 5 1.969 25.984 18.79 P.95 FT-V1 4 15.748 2 7.874 13 5.118 2 7.874 1 3.937 65 2.559 15 5.96 75 2.953 4 1.575 P.95 FT-V22 5 1.969 25.984 16.63 26 1.24 13.512 8.315 44 1.732 22.866 15.591 P.95 FT-V41 28 1.12 14.551 1.394 14.551 7.276 5.197 1.394 5.197 3.118 P.95 FT-V8Y 12 4.724 6 2.362 35 1.378 8 3.15 4 1.575 25.984 75 2.953 38 1.496 24.945 P.95 FT-W4 16.63 8.315 5.197 1.394 5.197 3.118 8.315 4.157 2.5.98 P.95 FT-W8 9 3.543 45 1.772 3 1.181 56 2.25 28 1.12 2.787 42 1.654 21.827 15.591 P.95 FT-WA8 6 23.622 3 11.811 22 8.661 3 11.811 15 5.96 11 4.331 22 8.661 11 4.331 8 3.15 P.95 FT-WA3 2,4 94.488 1,2 47.244 7 27.56 1,2 47.244 6 23.622 35 13.78 8 31.496 4 15.748 24 9.449 P.95 FT-WKV8 3 11.811 15 5.96 1 3.937 16 6.299 8 3.15 6 2.362 15 5.96 75 2.953 45 1.772 P.96 FT-WR8 9 3.543 45 1.772 3 1.181 56 2.25 28 1.12 2.787 48 1.89 22.866 14.551 P.96 FT-WR8 24 9.449 12 4.724 9 3.543 12 4.724 6 2.362 4 1.575 132 5.197 65 2.559 42 1.654 P.96 FT-WS3 9 3.543 45 1.772 3 1.181 56 2.25 28 1.12 2.787 P.96 FT-WS4 16.63 8.315 5.197 1.394 5.197 3.118 8.315 4.157 2.5.98 P.96 FT-WS8 9 3.543 45 1.772 3 1.181 56 2.25 28 1.12 2.787 42 1.654 21.827 15.591 P.96 FT-WS8 24 9.449 12 4.724 9 3.543 12 4.724 6 2.362 4 1.575 11 4.331 55 2.165 35 1.378 P.96 FT-WV42 P.96 FT-WZ4 35 1.378 15.591 9.354 18.79 8.315 4.8.189 43 1.693 15.591 9.354 P.96 FT-WZ4HB 32 1.26 15.591 9.6.378 16.63 9.354 5.4.213 4 1.575 15.591 12.472 P.97 FT-WZ7 8 3.15 4 1.575 24.945 54 2.216 27 1.63 16.2.638 54 2.126 27 1.63 16.2.638 P.97 FT-WZ7HB 1 3.937 5 1.969 3 1.181 56 2.25 28 1.12 16.8.661 56 2.25 28 1.12 16.8.661 P.97 FT-WZ8 8 3.15 4 1.575 25.984 4 1.575 2.787 13.512 36 1.417 18.79 12.472 P.97 FT-WZ8E 24 9.449 12 4.724 8 3.15 12 4.724 6 2.362 4 1.575 1 3.937 5 1.969 3 1.181 P.97 FT-WZ8H 4 15.748 2 7.874 14 5.512 2 7.874 1 3.937 7 2.756 18 7.87 9 3.543 65 2.559 P.97 FT-Z8 12 4.724 6 2.362 4 1.575 6 2.362 3 1.181 22.866 46 1.811 23.96 16.63 P.97 FT-Z8E 4 15.748 2 7.874 14 5.512 2 7.874 1 3.937 65 2.559 14 5.512 7 2.756 5 1.969 P.97 FT-Z8H 56 22.47 28 11.24 2 7.874 2 7.874 1 3.937 65 2.559 18 7.87 9 3.543 65 2.559 P.97 Dimensions FT-Z82Y 32 12.598 16 6.299 12 4.724 16 6.299 8 3.15 6 2.362 32 12.598 16 6.299 12 4.724 P.97 Notes: 1) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 2) Because infrared types are easily affected by humidity, please ask assistance when using them in a humid environment or in an environment with varying humidity.
189 Digital Sensor SERIES SENSING RANGE OF BUE ED / GREEN ED / INFRARED ED Retroreflective type are listed in alphabetic order. Refer to p.5~ for details of each fiber. Sensing range (mm in) (Note 1, 2) Model No. FX-31B FX-31G FX-31H Dimensions ONG ST ONG ST ONG ST FR-KV1 P.98 FR-KZ21 2 to 2.787 to 7.874 2 to 12.787 to 4.724 2 to 9.787 to 3.543 2 to 13.787 to 5.118 2 to 8.787 to 3.15 2 to 5.787 to 1.969 2 to 13.787 to 5.118 2 to 7.787 to 2.756 P.98 FR-KZ21E 2 to 16.787 to 6.299 2 to 1.787 to 3.937 2 to 6.787 to 2.362 2 to 11.787 to 4.331 2 to 9.787 to 3.543 P.98 FR-WKZ11 1 to 34 3.937 to 13.386 P.98 Notes: 1) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 2) The sensing range of retroreflective type is the possible setting range for the attached reflector. The fiber can detect an object less than setting range for the reflector. However, note that if there are any white or highly-reflective surfaces near the fiber, reflected incident light may affect the fiber. If this occurs, adjust the threshold value of the amplifier unit before use. Reflective type are listed in alphabetic order. Refer to p.5~ for details of each fiber. Model No. Sensing range (mm in) (Note 1, 2) FX-31B FX-31G FX-31H Dimensions ONG ST ONG ST ONG ST FD-3 19.748 9.354 6.236 9.354 4.5.177 2.5.98 8.315 4.157 2.5.98 P.99 FD-31 18.79 8.315 5.197 8.315 4.157 2.79 7.276 3.118 2.79 P.99 FD-4 19.748 9.354 6.236 9.354 4.5.177 2.5.98 8.315 4.157 2.5.98 P.99 FD-41 18.79 8.315 5.197 8.315 4.157 2.79 7.276 3.118 2.79 P.99 FD-6 55 2.165 28 1.12 18.79 3 1.181 15.591 1.394 3 1.181 15.591 1.394 P.99 FD-61 48 1.89 24.945 16.63 26 1.24 13.512 8.315 27 1.63 12.472 8.315 P.99 FD-A15 25.984 15.591 P.99 FD-AFM2 4 1.575 2.787 13.512 18.79 9.354 5.197 12.472 6.236 4.157 P.99 FD-AFM2E 4 1.575 2.787 13.512 18.79 9.354 5.197 12.472 6.236 4.157 P.99 FD-B8 8 3.15 4 1.575 26 1.24 42 1.654 21.827 14.551 26 1.24 13.512 9.354 P.99 FD-E12 2.79 1.39 1.39 1.39 P.1 FD-E22 6.236 3.118 2.79 3.118 1.5.59 1.39 6.236 3.118 2.79 P.1 FD-EG1 6.236 3.118 2.79 3.118 1.5.59 1.39 1.394 5.197 3.118 P.1 FD-EG2 5.197 2.79 1.39 2.79 1.39 6.236 3.118 2.79 P.1 FD-EG3 2.79 1.39 1.39 3.118 1.5.59 1.39 P.1 FD-EN5S1 P.1 FD-ENM1S1 6.236 3.118 2.79 3.118 1.5.59 1.39 4.157 2.79 1.5.59 P.1 Applicable pipe diameter: Outer dia. ø6 to ø26 mm ø.236 to ø1.24 in transparent pipe FD-F4 [P (fluorine resin) or equivalently transparent pipe, wall thickness 1 mm.39 in] P.1 Applicable pipe diameter: Outer dia. ø6 to ø26 mm ø.236 to ø1.24 in transparent pipe FD-F41 [PVC (vinyl chloride), fluorine resin, polycarbonate, acrylic, glass, wall thickness 1 to 3 mm.39 to.118 in] P.1 ø4 mm ø.157 in form Protective tube: fluorine resin, length 5 mm 19.685 in (cuttable) FD-F41Y iquid surface not contacted: Beam received, iquid surface contacted: Beam interrupted P.11 FD-F8Y P.11 Applicable pipe diameter: Outer dia. ø8 mm ø.315 in or more transparent pipe (When used with the tying bands: ø8 to ø8 mm ø.315 to ø3.15 in) [P (fluorine resin), including translucent] FD-9 iquid absent: Beam received, iquid present: Beam interrupted P.11 FD-FM2 46 1.811 23.96 15.591 24.945 12.472 8.315 2.787 1.394 7.276 P.11 FD-FM2S 46 1.811 23.96 15.591 24.945 12.472 8.315 2.787 1.394 7.276 P.11 FD-FM2S4 46 1.811 23.96 15.591 24.945 12.472 8.315 2.787 1.394 7.276 P.11 FD-G4 22.866 11.433 8.315 12.472 6.236 4.157 7.276 3.5.138 2.79 P.11 FD-G6 22.866 11.433 8.315 12.472 6.236 4.157 7.276 3.5.138 2.79 P.12 FD-G6X 33 1.299 11.433 6.236 12.472 6.236 4.157 7.276 3.5.138 2.79 P.12 FD-G4 22.866 11.433 8.315 12.472 6.236 4.157 7.276 3.5.138 2.79 P.11 FD-G6 46 1.811 23.96 15.591 24.945 12.472 8.315 2.787 1.394 7.276 P.12 FD-H13-FM2 2.787 11.433 7.276 2.787 11.433 7.276 25.984 12.472 8.315 P.12 FD-H18-31 P.12 FD-H2-21 36 1.417 18.79 12.472 2.787 1.394 7.276 14 5.512 7 2.756 45 1.772 P.12 FD-H2-M1 36 1.417 18.79 12.472 2.787 1.394 7.276 14 5.512 7 2.756 45 1.772 P.12 Notes: 1) The standard sensing objects of the sensing ranges vary depending on the fibers. 2) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut.
Digital Sensor SERIES 19 SENSING RANGE OF BUE ED / GREEN ED / INFRARED ED Reflective type are listed in alphabetic order. Refer to p.5~ for details of each fiber. Model No. Sensing range (mm in) (Note 1, 2) FX-31B FX-31G FX-31H ONG ST ONG ST ONG ST Dimensions FD-H25-43 P.13 FD-H25-45 P.13 FD-H3-KZ1V-S (Note 3) 3 to 4 1.181 to 1.575 P.13 FD-H3-32 P.13 FD-H3-32V-S (Note 3) P.13 FD-H35-2S 22.866 11.433 7.276 12.472 6.236 4.157 8 3.15 4 1.575 28 1.12 P.14 FD-H35-M2 36 1.417 18.79 12.472 2.787 1.394 7.276 14 5.512 7 2.756 45 1.772 P.14 FD-H35-M2S6 36 1.417 18.79 12.472 2.787 1.394 7.276 14 5.512 7 2.756 45 1.772 P.14 ø4 mm ø.157 in form Protective tube: fluorine resin, length:5 mm 19.685 in (allowable cutting) FD-HF4Y P.14 iquid surface not contacted: Beam received, iquid surface contacted: Beam interrupted 4.5 to 9.5.177 to.374 5 to 9.197 to.354 5.5 to 8.217 to.315 5 to 9.197 to.354 5.5 to 8.217 to.315 FD-4 4.5 to 9.5.177 to.374 P.14 (Convergent point 6.236) (Convergent point 6.236) (Convergent point 6.236) (Convergent point 6.236) (Convergent point 6.236) (Convergent point 6.236) FD-41 P.14 FD-43 P.14 FD-44 to 5.7 to.224 1 to 4.5.39 to.177 1.5 to 3.8.59 to.15 1 to 4.6.39 to.181 2.5 to 3.98 to.118 1 to 4.3.39 to.169 P.14 FD-44S to 3.5 to.138 1 to 3.39 to.118 1 to 3.39 to.118 1 to 4.3.39 to.169 P.14 FD-45 P.14 FD-45A P.15 FD-46 P.15 FD-47 P.15 FD-NFM2 16.63 8.315 5.197 8.315 4.157 2.79 6.236 3.118 2.79 P.15 FD-NFM2S 16.63 8.315 5.197 8.315 4.157 2.79 6.236 3.118 2.79 P.15 FD-NFM2S4 16.63 8.315 5.197 8.315 4.157 2.79 6.236 3.118 2.79 P.15 FD-P2 8.315 4.157 2.5.98 4.157 2.79 1.5.59 7.276 3.5.138 2.79 P.15 FD-P4 5.197 2.5.98 1.5.59 3.118 1.5.59 1.39 2.79 1.39 P.15 FD-P5 2.787 1.394 6.236 1.394 5.197 3.118 8.315 4.157 2.5.98 P.15 FD-P6 2.787 1.394 6.236 1.394 5.197 3.118 8.315 4.157 2.5.98 P.15 FD-P8 4 1.575 2.787 13.512 2.787 1.394 7.276 18.79 9.354 6.236 P.15 FD-P81X 32 1.26 16.63 1.394 16.63 8.315 5.197 18.79 9.354 6.236 P.16 FD-R8 32 1.26 16.63 1.394 16.63 8.315 5.197 1.394 5.197 3.118 P.16 FD-S3 19.749 9.354 6.236 9.354 4.5.177 2.5.98 8.315 4.157 2.5.98 P.16 FD-S31 18.79 8.315 5.197 8.315 4.157 2.79 7.276 3.118 2.79 P.16 FD-S8 46 1.811 23.96 15.591 24.945 12.472 8.315 2.787 1.394 7.276 P.16 FD-SFM2SV2 14.551 7.276 4.157 7.276 3.5.138 4.157 P.16 FD-SNFM2 16.63 8.315 5.197 8.315 4.157 2.79 6.236 3.118 2.79 P.16 FD-T4 16.63 8.315 5.197 8.315 4.157 2.79 6.236 3.118 2.79 P.16 FD-T8 46 1.811 23.96 15.591 24.945 12.472 8.315 2.787 1.394 7.276 P.16 FD-V41 6.236 3.118 3.118 P.16 FD-W8 23.96 11.433 8.315 14.551 7.276 4.157 11.433 5.5.217 3.118 P.17 FD-W44 5.197 2.5.98 1.5.59 3.118 1.5.59 1.39 2.79 1.39 P.17 FD-WG4 11.433 5.197 3.118 6.236 3.118 2.79 5.197 2.5.98 1.5.59 P.17 FD-WKZ1 P.17 FD-W41 P.17 FD-W48.5 to 3.5.2 to.138 P.17 FD-WS8 23.96 11.433 8.315 14.551 7.276 4.157 11.433 5.5.217 3.118 P.17 FD-WSG4 11.433 5.197 3.118 6.236 3.118 2.79 5.197 2.5.98 1.5.59 P.17 FD-WT4 5.197 2.5.98 1.5.59 3.118 1.5.59 1.39 2.79 1.39 P.17 FD-WT8 23.96 11.433 8.315 14.551 7.276 4.157 11.433 5.5.217 3.118 P.17 FD-WV42 P.18 FD-WZ4 5 to 8.197 to.315 P.18 FD-WZ4HB 4 to 9.157 to.354 4 to 12.157 to.472 P.18 FD-WZ7 4 to 15.157 to.591 5 to 8.197 to.315 P.18 FD-WZ7HB 3 to 28.118 to 1.12 3 to 14.118 to.551 4 to 8.4.157 to.331 3 to 16.118 to.63 4 to 8.157 to.315 4.8.189 3 to 18.118 to.79 P.18 Notes: 1) The standard sensing objects of the sensing ranges vary depending on the fibers. 2) Note that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. 3) Sold as a set comprising vacuum type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8).
191 Digital Sensor SERIES ens (for thru-beam type fiber) For thru-beam type fiber Designation Model No. Description Expansion lens (Note 1) Superexpansion lens (Note 1) Side-view lens Expansion lens for vacuum fiber (Note 1) Vacuum resistant side-view lens (Note 1) FX-E1 FX-E2 FX-SV1 FV-E1 FV-SV2 Increases the sensing range by 5 times or more. Ambient temperature: 6 to +35 C 76 to +662 F (Note 5) Tremendously increases the sensing range with large diameter lenses. Ambient temperature: 6 to +35 C 76 to +662 F (Note 5) Beam axis is bent by 9. Ambient temperature: 6 to +3 C 76 to +572 F (Note 5) Sensing range increases by 4 times or more. Ambient temperature: 6 to +35 C 76 to +662 F (Note 5) Beam axis is bent by 9. Ambient temperature: 6 to +3 C 76 to +572 F (Note 5) Sensing range for red ED type (mm) [ens on both sides] (Note 3) Mode U-G ONG ST S-D H-SP FT-B8 3,5 (Note 2) 3,5 (Note 2) 3, 2,5 2, 1, 1, FT-FM2 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 2,5 1,3 1, FT-T8 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 2,5 1,3 1, FT-R8 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 2,3 1,6 8 75 FT-W8 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 2,9 2, 1, 9 FT-P8 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 2,5 1,1 1, FT-P6 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 1,5 9 8 FT-P81X 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,1 95 FT-H35-M2 3,5 (Note 2) 3,5 (Note 2) 2,5 2, 1,5 75 7 FT-H2W-M1 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,3 9 5 4 FT-H2-M1 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,1 9 6 Sensing range for red ED type (mm) [ens on both sides] (Note 3) Mode U-G ONG ST S-D H-SP FT-B8 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) FT-FM2 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) FT-R8 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) FT-W8 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) FT-P8 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) FT-P6 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) FT-P81X 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) FT-H35-M2 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) FT-H2W-M1 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,5 1,6 (Note 2) FT-H2-M1 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) 1,6 (Note 2) FT-H13-FM2 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) 3,5 (Note 2) Sensing range for red ED type (mm) [ens on both sides] (Note 3) Mode U-G ONG ST S-D H-SP FT-B8 1,45 1,1 66 53 4 186 18 FT-FM2 1,8 1,2 81 6 44 21 21 FT-T8 1,8 1,2 81 6 44 21 21 FT-W8 1,3 9 6 45 33 16 16 FT-P8 1,8 1,2 81 6 44 21 21 FT-P6 85 65 4 3 2 13 12 FT-P81X 1,8 1,2 81 6 44 2 2 FT-H35-M2 84 55 37 28 2 9 9 FT-H2W-M1 4 31 18 14 1 5 5 FT-H2-M1 84 55 37 28 2 9 9 Sensing range for red ED type (mm) [ens on both sides] (Note 3, 4) Mode U-G ONG ST S-D H-SP FT-H3-M1V-S 1,6 1,2 65 45 3 15 2 Sensing range for red ED type (mm) [ens on both sides] (Note 3, 4) Mode U-G ONG ST S-D H-SP FT-H3-M1V-S 1,6 1,2 65 45 3 15 2 Notes: 1) Be careful when installing the thru-beam type fiber equipped with the expansion lens, as the beam envelope becomes narrow and alignment is difficult. Especially when installing a fiber with many cores (sharp bending fibers and heat-resistant glass fiber), please be sure to use it only after you have adjusted it sufficiently. 2) The fiber cable length practically limits the sensing range to 3,5 mm 137.795 in long (FT-P81X, FT-H2W-M1 and FT-H2-M1: 1,6 mm 62.992 in). 3) The sensing ranges are the values for red ED type amplifier. Please contact our office for details on sensing ranges for other types of amplifiers. 4) The fiber cable length for the FT-H3-M1V-S is 1 m 3.281 ft. The sensing ranges in U-G and ONG modes take into account the length of the FT-J8 atmospheric side fiber. 5) Refer to p.76~ for the ambient temperatures of fibers to be used in combination.
Digital Sensor SERIES 192 ens (for reflective type fiber) For reflective type fiber Designation Model No. Description Pinpoint spot lens Zoom lens Finest spot lens Finest spot lens Zoom lens Side-view type FX-MR1 FX-MR2 FX-MR3 FX-MR6 FX-MR5 Screw-in depth Distance to focal point Distance to focal point Distance to focal point Spot diameter Screw-in depth Spot diameter Spot diameter Pinpoint spot of ø.5 mm ø.2 in. Enables detection of minute objects or small marks. Distance to focal point: 6 ±1 mm.236 ±.39 in Applicable fibers: FD-WG4, FD-G4 Ambient temperature: 4 to +7 C 4 to +158 F (Note 2) The spot diameter is adjustable from ø.7 to ø2 mm ø.28 to ø.79 in according to how much the fiber is screwed in. Applicable fibers: FD-WG4, FD-G4 Ambient temperature: 4 to +7 C 4 to +158 F (Note 2) Accessory: MS-EX-3 (mounting bracket) Extremely fine spot of ø.3 mm ø.12 in approx. achieved. Applicable fibers: FD-WG4, FD-G4, FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6 Ambient temperature: 4 to +7 C 4 to +158 F (Note 2) Extremely fine spot of ø.1 mm ø.4 in approx. achieved. Applicable fibers: FD-WG4, FD-G4, FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6 Ambient temperature: 2 to +6 C 4 to +14 F (Note 2) Sensing range for red ED type (Note 1) Screw-in depth Distance to focal point Spot diameter 7 mm.276 in ø18.5 mm ø.728 in approx. ø.7 mm ø.28 in 12 mm.472 in ø27 mm ø1.63 in approx. ø1.2 mm ø.47 in 14 mm.551 in ø43 mm ø1.693 in approx. ø2. mm ø.79 in Sensing range for red ED type (Note 1) Distance to focal point Spot diameter FD-EG3 7.5 ±.5 mm.295 ±.2 in ø.15 mm ø.6 in approx FD-EG2 7.5 ±.5 mm.295 ±.2 in ø.2 mm ø.8 in approx FD-EG1 7.5 ±.5 mm.295 ±.2 in ø.3 mm ø.12 in approx FD-WG4/G4/G6X/G6 7.5 ±.5 mm.295 ±.2 in ø.5 mm ø.2 in approx Sensing range for red ED type (Note 1) Distance to focal point Spot diameter FD-EG3 7 ±.5 mm.276 ±.2 in ø.1 mm ø.4 in approx FD-EG2 7 ±.5 mm.276 ±.2 in ø.15 mm ø.6 in approx FD-EG1 7 ±.5 mm.276 ±.2 in ø.2 mm ø.8 in approx FD-WG4/G4/G6X/G6 7 ±.5 mm.276 ±.2 in ø.4 mm ø.16 in approx FX-MR2 is converted into a Sensing range for red ED type (Note 1) side-view type and can be mounted in a very small space. Screw-in depth Distance to focal point Spot diameter Applicable fibers: FD-WG4, FD-G4 8 mm.315 in 13 mm.512 in approx. ø.5 mm ø.2 in Ambient temperature: 1 mm.394 in 15 mm.591 in approx. ø.8 mm ø.31 in 4 to +7 C 4 to +158 F (Note 2) 14 mm.551 in 3 mm 1.181 in approx. ø3. mm ø.118 in Notes: 1) The sensing ranges are the values when used in combination with red ED type amplifier. Please contact our office for details on sensing ranges for other types of amplifier. 2) Refer p.76~ for the ambient temperatures of fibers to be used in combination. Others Protective tube bender Designation Model No. Description Protective tube (For thru-beam type fiber) Protective tube (For reflective type fiber) bender FB-1 FTP-5 (.5 m 1.641 ft) FTP-1 (1 m 3.281 ft) FTP-15 (1.5 m 4.922 ft) FTP-N5 (.5 m 1.641 ft) FTP-N1 (1 m 3.281 ft) FTP-N15 (1.5 m 4.922 ft) FDP-5 (.5 m 1.641 ft) FDP-1 (1 m 3.281 ft) FDP-15 (1.5 m 4.922 ft) FDP-N5 (.5 m 1.641 ft) FDP-N1 (1 m 3.281 ft) FDP-N15 (1.5 m 4.922 ft) Universal sensor MS-AJ1-F mounting stand (Note 2) MS-AJ2-F Single core FX-AT15A holder For M4 thread For M3 thread For M6 thread For M4 thread Applicable fibers FT-42 FT-B8 FT-FM2 FT-FM2S FT-31 FT-NFM2 FT-NFM2S FT-NFM2S4 FD-61 FD-B8 FD-FM2 FD-FM2S FT-FM2S4 FT-H13-FM2 FT-P6 FT-P8 FT-P4 FT-T8 FD-P4 FD-T4 FD-FM2S4 FD-H13-FM2 FD-P8 FD-41 FD-T8 FD-NFM2 FD-NFM2S FD-NFM2S4 The protective tube, made of noncorrosive stainless steel, protects the inner fiber cable from any external forces. The fiber bender bends the sleeve part of the fiber at the proper radius. (Note 1) Horizontal mounting type Mounting stand assembly for fiber Vertical mounting type (For M3,M4 or M6 threaded fiber) The incident light intensity may vary when using a multi-core fiber or a thin type sharp bending fiber. This holder suppresses the variation in the incident light intensity. Brown. Notes: 1) Do not bend the sleeve part of any side-view type fiber or ultra-small diameter type fiber. 2) Refer to the universal sensor mounting stand MS-AJ series pages for details. FTP- FDP- Universal sensor mounting stand Using the arm which enables adjustment in the horizontal direction, sensing can also be done from above an assembly line. MS-AJ1-F Swivel: 36 rotation Forward / back adjustment: 13 mm 5.118 in approx 36 2 2 Angle adjustment: ±2 MS-AJ2-F Forward / back adjustment: 13 mm 5.118 in approx 36 2 2 Angle adjustment: ±2 Swivel: 36 rotation FB-1 Height adjustment: 15 mm 5.96 in approx. Mounting hole for M6 screw Single core holder FX-AT15A Height adjustment: 15 mm 5.96 in approx. Mounting hole for M6 screw
193 Digital Sensor SERIES SPECIFICATIONS Type Standard type High-speed Red ED Blue ED Green ED Infrared ED type High-function type NPN output FX-31 FX-31B FX-31G FX-31H FX-31-HS FX-35 Item PNP output FX-31P FX-31BP FX-31GP FX-31HP FX-31P-HS FX-35P Supply voltage 12 to 24 V DC ±1 % Ripple P-P 1 % or less Model No. Power consumption Output Output operation Short-circuit protection Response time Sensitivity setting <Red ED / Infrared ED type> Normal operation: 96 mw or less (Current consumption 4 ma or less at 24 V supply voltage) ECO mode: 6 mw or less (Current consumption 25 ma or less at 24 V supply voltage) <NPN output type> NPN open-collector transistor Maximum sink current:1 ma (5 ma, if five, or more, amplifiers are connected in cascade.) Applied voltage: 3 V DC or less (between output and V) Residual voltage: 1.5 V or less [at 1 ma (at 5 ma, if five, or more, amplifiers are connected in cascade) sink current.] <Blue ED / Green ED type> Normal operation: 72 mw or less (Current consumption 3 ma or less at 24 V supply voltage) ECO mode: 43 mw or less (Current consumption 18 ma or less at 24 V supply voltage) <NPN output type> NPN open-collector transistor 2 outputs Maximum sink current: 5 ma each (Note 2) Applied voltage: 3 V DC or less (between output and V) Residual voltage: 1.5 V or less [at 5 ma (Note 2)] <PNP output type> <PNP output type> PNP open-collector transistor PNP open-collector transistor 2 outputs Maximum source current: 1 ma (5 ma, if five, or more, amplifiers are connected in cascade.) Maximum source current: 5 ma each (Note 2) Applied voltage: 3 V DC or less (between output and +V) Applied voltage: 3 V DC or less (between output and +V) Residual voltage: 1.5 V or less [at 1 ma (at 5 ma, if five, or more, amplifiers are connected in cascade) source current.] Residual voltage: 1.5 V or less [at 5 ma (Note 2)] 65 µs or less [H-SP (Red ED type only)], 15 µs or less (ST), 25 µs or less [ / S-D (Red ED type only)], 2 ms or less (ONG), selectable with jog switch Selectable either ight-on or Dark-ON, with jog switch Incorporated 2-point teaching / imit teaching / Manual adjustment / Full-auto teaching / Max. sensitivity teaching 35 µs or less (H-SP), 15 µs or less (ST), 25 µs or less ( / S-D), 2 ms or less (ONG), selectable with jog switch 65 µs or less (H-SP), 15 µs or less (ST), 25 µs or less (), 7 µs or less (), 2.5 ms or less (ONG), 4.5 ms or less (U-G), selectable with jog switch Normal mode: 2-point teaching / imit teaching / Full-auto teaching / Max. sensitivity teaching / Manual adjustment Window comparator mode: Teaching (1-point / 2-point / 3-point) / Manual adjustment Operation indicator Orange ED (lights up when the output is ON) Stability indicator Green ED (lights up under stable light received condition or stable dark condition) MODE indicator RUN: Green ED, TEACH ADJ /D ON TIMER PRO: Yellow ED Digital display 4 digit red ED display Fine sensitivity adjustment function Incorporated Timer function ight emitting amount selection function Automatic interference prevention function Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. Timer period: Red ED type;.5 ms approx., 1 to 9999 ms (Blue ED, Green ED, Infrared ED type; approx..5 to 5 ms) Incorporated (Red ED type only) (Note 3) ST,, ONG: 4 level, H-SP: 3 level, S-D: 2 level Incorporated (Up to four sets of fiber s can be mounted close together. However, H-SP mode is 2 fiber s.) (Note 4) Incorporated (Note 3) ST,, ONG: 4 level H-SP, S-D: 2 level Incorporated with variable ON-delay / OFF-delay / ONE SHOT / ON-delay OFF-delay / ON-delay ONE SHOT timer, switchable either effective or ineffective. (Timer period: Output 1;.5 ms, 1 to 9999 ms, Output 2;.5 ms, 1 to 5 ms) Incorporated (Note 3) ST,,, ONG, U-G: 4 level H-SP: 3 level Incorporated [Up to four sets of fiber s can be mounted close together. (However, U-G mode is 8 fiber s, H-SP mode is 2 fiber s.)] (Note 5) Ambient temperature 1 to +55 C +14 to +131 F (If 4 to 7 units are connected in cascade: 1 to +5 C +14 to +122 F, if 8 to 16 units are connected in cascade: 1 to +45 C +14 to +113 F) (No dew condensation or icing allowed), Storage: 2 to +7 C 4 to +158 F Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH Ambient illuminance Incandescent light: 3, lx at the light-receiving face Voltage withstandability 1, V AC for one min. between all supply terminals connected together and enclosure (Note 6) Insulation resistance 2 MΩ, or more, with 25 V DC megger between all supply terminals connected together and enclosure (Note 6) Vibration resistance 1 to 15 Hz frequency,.75 mm.3 in amplitude in X, Y and Z directions for two hours each Shock resistance 98 m/s 2 acceleration (1 G approx.) in X, Y and Z directions for five times each Emitting element (modulated) Red ED Blue ED Green ED Infrared ED Red ED Red ED Peak emission wavelength 65 nm.26 mil 47 nm.19 mil 525 nm.21 mil 94 nm.37 mil 65 nm.26 mil 65 nm.26 mil Material Enclosure: Heat-resistant ABS, Case cover: Polycarbonate, MODE key: Acrylic, Jog switch: Heat-resistant ABS (FX-31B/G/H: Acrylic) Connecting method Connector (Note 7) Cable length Total length up to 1 m 328.84 ft (5 m 164.42 ft for 5 to 8 units, 2 m 65.617 ft for 9 to 16 units) is possible with.3 mm 2, or more, cable. Weight Net weight: 2 g approx., Gross weight: 25 g approx. Accessory FX-MB1 (amplifier protection seal): 1 set FX-MB1 (amplifier protection seal): 1 set Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 C +73.4 F. 2) 5 ma per output. 25 ma if five, or more, amplifiers are connected in cascade. 3) The light emitting amount can be zero (emission halt) in all modes. 4) When the power supply is switched on, the light emission timing is automatically set for interference prevention. 5) When the interference prevention function is set, the number of mountable fiber s becomes double. Furthermore, take care that the response time also becomes double. 6) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only. 7) The cable for amplifier connection is not supplied as an accessory. Make sure to use the optional quick-connection cables given below. Main cable (3-core) for FX-31(P)(-HS): CN-73-C1 (Cable length 1 m 3.281 ft), CN-73-C2 (Cable length 2 m 6.562 ft), CN-73-C5 (Cable length 5 m 16.44 ft) Sub cable (1-core) for FX-31(P)(-HS): CN-71-C1 (Cable length 1 m 3.281 ft), CN-71-C2 (Cable length 2 m 6.562 ft), CN-71-C5 (Cable length 5 m 16.44 ft) Main cable (4-core) for FX-35(P): CN-74-C1 (Cable length 1 m 3.281 ft), CN-74-C2 (Cable length 2 m 6.562 ft), CN-74-C5 (Cable length 5 m 16.44 ft) Sub cable (2-core) for FX-35(P): CN-72-C1 (Cable length 1 m 3.281 ft), CN-72-C2 (Cable length 2 m 6.562 ft), CN-72-C5 (Cable length 5 m 16.44 ft) Environmental resistance
Digital Sensor SERIES 194 Sensor circuit I/O CIRCUIT AND WIRING DIAGRAMS FX-31(-HS) I/O circuit diagram Sensor circuit Tr Tr1 Tr2 D D ZD1 ZD Terminal No. Color code of quick-connection cable (Brown) +V (Note 1) 1 oad (Black) Output 3 1 ma max. (Note 2) (Blue) V (Note 1) 2 Terminal No. Color code of quick-connection cable (Brown) +V (Note 1) 1 5 ma max. (Note 2) 3 ZD2 (Black) Output 1 5 ma max. (Note 2) 4 (White) Output 2 oad 2 (Blue) V (Note 1) oad 12 to 24 V DC ±1 % Internal circuit Users circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and V (blue). The power is supplied from the connector of the main cable. 2) 25 ma max., if five amplifiers, or more, are connected together. + 12 to 24 V DC ±1 % Internal circuit Users circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and V (blue). The power is supplied from the connector of the main cable. 2) 5 ma max., if five amplifiers, or more, are connected together. Symbols D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : NPN output transistor FX-31P(-HS) I/O circuit diagram Sensor circuit Tr D ZD Terminal No. Color code of quick-connection cable (Brown) +V (Note 1) 1 1 ma max. (Note 2) 3 (Black) Output oad (Blue) V (Note 1) 2 + 12 to 24 V DC ±1 % Internal circuit Users circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and V (blue). The power is supplied from the connector of the main cable. 2) 5 ma max., if five amplifiers, or more, are connected together. Symbols D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor FX-35 I/O circuit diagram Sensor circuit Terminal No. Color code of quick-connection cable D (Brown) +V (Note 1) 1 Tr1 (Black) Output oad 3 oad Tr2 ZD1 (White) Output 2 5 ma max. (Note 2) 4 ZD2 5 ma max. (Note 2) 2 (Blue) V (Note 1) Internal circuit Users circuit Notes: 1) The quick-connection sub cable does not have +V (brown) and V (blue). The power is supplied from the connector of the main cable. 2) 25 ma max., if five amplifiers, or more, are connected together. Symbols D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr1, Tr2 : NPN output transistor FX-35P I/O circuit diagram Symbols D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr1, Tr2 : PNP output transistor + + 12 to 24 V DC ±1 % Wiring diagram Brown (Note) Black NPN output type Color code of quick-connection cable oad 12 to 24 V DC ±1 % Blue (Note) Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arrangement diagram Wiring diagram 1 +V 3 Output 2 V Brown (Note) + PNP output type Color code of quick-connection cable Black + 12 to 24 V DC ±1 % oad Blue (Note) Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arrangement diagram Wiring diagram 1 +V 3 Output 2 V Brown (Note) Black White NPN output type Blue (Note) Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arrangement diagram Wiring diagram 1 +V Color code of quick-connection cable oad oad 3 Output 1 4 Output 2 2 V Brown (Note) Black White + 12 to 24 V DC ±1 % PNP output type Blue (Note) Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arrangement diagram 1 +V Color code of quick-connection cable oad oad 3 Output 1 4 Output 2 2 V + 12 to 24 V DC ±1 %
195 Digital Sensor SERIES SENSING CHARACTERISTICS (TYPICA) The following sensing characteristics pertain to the red ED type.please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here. Thru-beam type Parallel deviation Sensing characteristics are listed by model No. in alphabetical order. (However, models with the same sensing characteristics are listed together.) FT-A8 FT-WA8 Horizontal direction 4, 157.48 U-G 3, 118.11 2, 78.74 H-SP 1, l 39.37 2 1 1 2 7.874 3.937 3.937 7.874 eft Center Right FT-NFM2 FT-NFM2S FT-NFM2S4 FT-SNFM2 4 15.748 U-G Thru-beam type 2 7.874 H-SP l 2 1 1 2 7.874 3.937 3.937 7.874 eft Center Right FD-B8 8 31.496 6 23.662 4 15.748 2 7.874 H-SP Reflective type White non-glossy paper l U-G 1 5 5 1 3.937 1.969 1.969 3.937 eft Center Right Reflective type Sensing fields FD-NFM2 FD-NFM2S FD-NFM2S4 FD-SNFM2 FD-T4 2 7.874 15 5.96 1 3.937 5 1.969 H-SP Reflective type White non-glossy paper U-G l 2 1 1 2.787.394.394.787 eft Center Right Vertical direction 4, 157.48 3, 118.11 2, 78.74 1, 39.37 Thru-beam type U-G H-SP 2 1 1 2 7.874 3.937 3.937 7.874 Down Center Up FT-P81X 1, 39.37 l 8 mm.315 in approx. Thru-beam type U-G 5 19.685 H-SP l 4 2 2 4 15.748 7.874 7.874 15.748 eft Center Right FT-B8 2, 78.74 1,5 59.6 Thru-beam type U-G 1, 39.37 H-SP 5 19.685 l 8 4 4 8 31.496 15.748 15.748 31.496 eft Center Right FT-FM2 FT-FM2S FT-FM2S4 FT-SFM2 FT-T8 1, 39.37 5 19.685 H-SP l U-G Thru-beam type 4 2 2 4 15.748 7.874 7.874 15.748 eft Center Right FT-W4 FT-WS4 Thru-beam type FT-W8 FT-WS8 Thru-beam type 2 7.874 1 3.937 U-G H-SP l 4 2 2 4 1.575.787.787 1.575 eft Center Right 8 31.496 6 23.662 U-G 4 15.748 H-SP 2 l 7.874 2 1 1 2 7.874 3.937 3.937 7.874 eft Center Right Sensing characteristics are listed by model No. in alphabetical order. (However, models with the same sensing characteristics are listed together.) FD-FM2 4 15.748 2 7.874 H-SP Reflective type U-G White nonglossy paper l 1 5 5 1 3.937 1.969 1.969 3.937 eft Center Right FD-P81X 4 15.748 3 11.811 2 7.874 1 3.937 H-SP Reflective type White non-glossy paper l U-G 1 5 5 1 3.937 1.969 1.969 3.937 eft Center Right FD-G4 2 7.874 15 5.96 1 3.937 5 1.969 H-SP Reflective type White non-glossy paper l U-G 2 1 1 2.787.394.394.787 eft Center Right FD-W8 FD-WS8 FD-WT8 4 15.748 3 11.811 2 7.874 1 3.937 H-SP Reflective type White non-glossy paper l U-G 4 2 2 4 1.575.787.787 1.575 eft Center Right FD-G6X 2 7.874 15 5.96 1 3.937 5 1.969 4 1.575 H-SP FD-WG4 FD-WSG4 1 3.937 5 1.969 1.394 Reflective type White non-glossy paper l U-G 2.787 2.787 4 1.575 eft Center Right H-SP Reflective type White non-glossy paper l U-G 5.197 5.197 1.394 eft Center Right
Digital Sensor SERIES 196 PRECAUTIONS FOR PROPER Refer to General precautions, p.8~ for fiber precautions, and to the PRO mode operation guide on our website for details pertaining to operating instructions for the amplifier. Mounting Connection Never use this product as a sensing device for personnel protection. In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. The digital fiber sensor FX-31(P) has been modified since its production in June 24. The explanations below are about the modified product. How to mount the amplifier Fit the rear part of the mounting section of the amplifier on a 35 mm 1.378 in width DIN rail. Press down the rear part of the mounting section of the unit on the 35 mm 1.378 in width DIN rail and fit the front part of the mounting section to the 35 mm 1.378 in width DIN rail. How to remove the amplifier Push the amplifier forward. ift up the front part of the amplifier to remove it. Note: Take care that if the front part is lifted without pushing the amplifier forward, the hook on the rear portion of the mounting section is likely to break. installation 35 mm 1.378 in width DIN rail Insert the fiber into the amplifier after attaching the attachment. Refer to the "Instruction Manual" included with the fiber for details. Push the fiber lock lever down. Slowly insert the fiber into the insertion lock lever slot until it stops. (Note 1) Push the fiber lock lever back up until it stops. Notes: 1) Note that if the fiber is not fully inserted, the sensing distance will decrease. Also note that the flexible fiber may bend during insertion. 2) In case of coaxial reflective type fibers (FD-G4, FD-FM2, etc.), mount the central fiber (single-core) to the emitter part and the peripheral fiber (multi-core) to the receiver. Note that sensing precision will deteriorate when done in reverse. Make sure that the power supply is off while connecting or disconnecting the quick-connection cable. Connection method Holding the connector of the quick-connection cable, align its projection with the groove at the top portion of the amplifier connector. Insert the connector till a click is felt. Groove Projection Quick-connection cable Disconnection method Pressing the projection at the top of the quick-connection cable, pull out the connector. Note: Take care that if the connector is pulled out without pressing the projection, the projection may break. Do not use a quick-connection cable whose projection has broken. Further, do not pull by holding the cable, as this can cause a cable-break. Cascading Projection Make sure that the power supply is off while adding or removing the amplifiers. Make sure to check the allowable ambient temperature, as it depends on the number of amplifiers connected in cascade. In case two, or more, amplifiers are connected in cascade, make sure to mount them on a DIN rail. When the amplifiers move on the DIN rail depending on the attaching condition or the amplifiers are mounted close to each other in cascade, fit them between the optional end plates (MS-DIN-E) mounted at the two ends. Up to maximum 15 amplifiers can be added (total 16 amplifiers connected in cascade.) When connecting more than two amplifiers in cascade, use the sub cable (CN-71-C / CN-72-C ) as the quick-connection cable for the second amplifier onwards. When connecting amplifiers not close to each other in parallel, be sure to mount the optional end plate (MS-DIN-E) at both sides of each amplifier or affix the communication window seal of the accessory amplifier protection seal (FX-MB1) to the communication windows. The settings other than the interference prevention function cannot be transmitted between FX-31(P) FX-31B/G/H(P), FX-35(P). Therefore, in case both models of amplifiers are mounted in cascade, be sure to mount identical models together. However, the interference prevention function is not incorporated in the FX-31(P)-HS. Take care when the sensors are mounted in cascade. If the FX-31(P) updated version unit or the FX-35(P) is mounted with the FX-31(P) previous version unit or the FX-31B/G/H(P) in cascade, place the FX-31(P) updated version units and the FX-35(P) units to the right side (seen from the connector side) of the previous version units. For details, refer to Cautions on sensor connection in cascade. For a difference between the updated version unit and the previous version unit, refer to A difference between the updated version unit and the previous version unit. The communication function of this product and that of the FX-31(P)-F / F7 is different. If these models are mounted in cascade, affix the accessory fiber amplifier protection seal (FX-MB1) included in the FX-31(P) and FX-35(P) to the communication windows of the amplifiers.
197 Digital Sensor SERIES PRECAUTIONS FOR PROPER Refer to General precautions, p.8~ for fiber precautions, and to the PRO mode operation guide on our website for details pertaining to operating instructions for the amplifier. Cascading method Mount the amplifiers, one by one, on the 35 mm 1.378 in width DIN rail. Slide the amplifiers next to each other, and connect the quickconnection cables. Mount the optional end plates (MS-DIN-E) at both the ends to hold the amplifiers between their flat sides. Tighten the screws to fix the end plates. Main unit Sub unit 35 mm 1.378 in width DIN rail Sub cable (CN-71/72-C ) (Optional) Slide Main cable (CN-73/74-C ) (Optional) How to change the communication specification of Group B Change the communication specification of Group B according to the following procedures. Make sure to set the communication specification to (Group A communication specification) or (Optical Communication Stop). <Changing Procedure> Display [PRO4]. ong press the [Jog Switch] and [MODE key] at the same time. (Note 3) Dismantling oosen the screws of the end plates. Remove the end plates. Slide the amplifiers and remove them one by one. Cautions on sensor connection in cascade When the units in the group A and the group B shown in the table below are connected in cascade, connect them in cascade as <Figure A> shown below. <Figure A> <Figure B> Optical communications Optical communications are possible are impossible Group A Group B Group B Group A Group A Group B End plate (MS-DIN-E) (Optional) Slide FX-31(P): Previous version unit (Note 1), FX-31G(P)/B(P)/H(P), FX-41 (P), S-41(P) (Note 2) FX-31(P): Updated version unit (Note 1), FX-35(P) Notes: 1) For the difference between the updated version unit and the previous version unit, refer to A difference between the updated version unit and the previous version unit. 2) When S-41(P) is connected with the digital fiber amplifier in cascade, be sure to locate S-41(P) at the left-most position (when viewed from the connector side). When the units of the group A and the group B are connected in cascade as <Figure B> shown above, optical communications cannot be done. When the optical communications function is used, connect them as <Figure A> shown above. If the units cannot be placed as <Figure A>, the following measure 1 or 2 should be taken. 1 Affix the communication window seal of the accessory fiber amplifier protection seal (FX-MB1) to the communication window of the FX-31(P) updated version unit or FX-35(P). 2 If the measure 1 described above cannot be taken, change the optical communications spec. of the group B units. Group B's Communication Specification Notes: 3) Every time the [Jog Switch] and the [MODE key] is simultaneously long pressed, the display changes in this sequence:. When you release the [Jog Switch] and [MODE key], the communication specification will be set and PRO4 will be displayed. Notes: 4) When the communication specification is set to (Group A communication specification), make sure to tightly attach the products. Also make sure to take note of the following: There are instances when the optical communication function cannot be used due to the usage environment, etc. Do not perform batch channel loading or saving. Part description Operation indicator (Orange) (Note1) MODE indicator / RUN (Green) MODE indicator / TEACH (Yellow) MODE indicator / ADJ (Yellow) Group A's Communication Specification Stability indicator (Green)(Note2) MODE indicator / PRO (Yellow) Digital display (Red) MODE indicator / /D ON (Yellow) MODE indicator / TIMER (Yellow) Notes: 1) FX-35(P); Output 1 operation indicator (Orange) 2) FX-35(P); Output 2 operation indicator (Orange) Operation procedure Optical Communication Stop Jog switch MODE key When the power supply is switched on, communication self-check is carried out and normal condition is displayed [MODE indicator / RUN (green)] lights up and the digital display shows the incident light intensity. When the MODE key is pressed, the mode will change as shown in the following diagram. Power ON [Teaching] (P.198) [Threshold value fine adjust] (P.199) Communication self-check RUN TEACH ADJ Press MODE key Press MODE key Press MODE key Press MODE key Press MODE key Press MODE key PRO TIMER /D [PRO mode] (P.22) [Timer operation setting] (P.199) [Output operation setting] (P.199) When Jog switch is pressed, the setting is confirmed. When MODE key is pressed for 2 sec., or more, the sensor returns to the RUN mode. Cancellation is possible by pressing MODE key during setting.
Digital Sensor SERIES 198 PRECAUTIONS FOR PROPER Refer to General precautions, p.8~ for fiber precautions, and to the PRO mode operation guide on our website for details pertaining to operating instructions for the amplifier. For FX-35(P) The FX-35(P) is equipped with two independent outputs, but the items that can be set in output 1 and output 2 respectively are only the following. The items other than those are common. 1 Threshold value 2 Output operation 3 Timer operation and Timer period 4 Sensing mode Teaching The threshold values can be set by 2-point teaching, limit teaching, full-auto teaching or window comparator mode (1-point, 2-point, 3-point teaching) [only for FX-35(P)], when the MODE indicator / TEACH (yellow) lights up. In case of 2-point teaching This is the method of setting the threshold value by teaching two levels, corresponding to the object present and object absent conditions. Normally, setting is done by this method. Step Description Display Set the fiber within the sensing range. Press MODE key to light up MODE indicator / TEACH (yellow). For FX-35(P), select either Output 1 or Output 2 beforehand, press jog switch in the object present condition. If the teaching is accepted, the read incident light intensity blinks in the digital display. Thru-beam type Beam blocked condition Reflective type Mark Background MODE indicator / TEACH (yellow) blinks. Press jog switch in the object absent condition. Thru-beam type Reflective type Mark Beam incident condition Background If the teaching is accepted, the read incident light intensity blinks in the digital display and the threshold value is set at the midvalue between the incident light intensities in the object present and the object absent conditions. After this, the judgment on the stability of sensing is displayed. In case stable sensing is possible: is displayed. In case stable sensing is not possible: blinks. The threshold value is displayed. blinks in the digital display. (only FX-31B/G/H) The incident light intensity appears in the digital display and the setting is complete. Notes: 1) Do not move or bend the fiber cable after the sensitivity setting. Detection may become unstable. 2) In case a reflective-type fiber is used, maximum sensitivity will be set if the jog switch is pushed while in no work status in procedure and. In case of full auto-teaching Full auto-teaching is used when it is desired to set the threshold value without stopping the assembly line, with the object in the moving condition. Step Description Display Set the fiber within the sensing range. Press MODE key to light up MODE indicator / TEACH (yellow). For FX-35(P), select either Output 1 or Output 2 beforehand, press the jog switch continuously for.5 sec. or more with the object moving on the assembly line. (The incident light intensity is displayed during sampling.) is displayed on the digital display. Release the jog switch when the object has passed. If the teaching is accepted, the read incident light intensity blinks in the digital display and the threshold value is set at the midvalue between the incident light intensities in the object present and the object absent conditions. After this, the judgment on the stability of sensing is displayed. In case stable sensing is possible: is displayed. In case stable sensing is not possible: blinks. The threshold value is displayed. blinks in the digital display. (only FX-31B/G/H) The incident light intensity appears in the digital display and the setting is complete. Notes: 1) The threshold value s shift amount can be selected in PRO mode. Refer to the PRO Mode Operation for more details pertaining to setting instructions. (Increments of 5 % between 45 and 45 % for setting possible. % default.) 2) Do not move or bend the fiber cable after the sensitivity setting. Detection may become unstable.
199 Digital Sensor SERIES PRECAUTIONS FOR PROPER Refer to General precautions, p.8~ for fiber precautions, and to the PRO mode operation guide on our website for details pertaining to operating instructions for the amplifier. In case of limit teaching This is the method of setting the threshold value by teaching only the object absent condition (stable incident light condition). This is used for detection in the presence of a background body or for detection of small objects. Step Description Display Set the fiber within the sensing range. Press MODE key to light up MODE indicator / TEACH (yellow). For FX-35(P), select either Output 1 or Output 2 beforehand, press jog switch in the object absent condition. If the teaching is accepted, the read incident light intensity blinks in the display. Thru-beam type Reflective type Beam incident condition Background body MODE indicator / TEACH (yellow) blinks. Turn jog switch to the + side or side. If jog switch is turned to the + side, scrolls (twice) the display from right to left (Note 1), and the threshold level is shifted to a value approx. 15 % higher (lower sensitivity) than that set at. (Note 2) This is used in case of reflective type fibers. If jog switch is turned to the side, scrolls (twice) the display from left to right, and the threshold level is shifted to a value approx. 15 % lower (higher sensitivity) than that set at. (Note 2) This is used in case of thru-beam type fibers. High Threshold value ow 15 % 1 % 15 % OFF ON After this, the judgment on whether the setting shift amount can be shifted or not is displayed. In case shifting is possible: blinks. In case shifting is not possible: blinks. The threshold value is displayed. blinks in the digital display. (only FX-31B/G/H) The incident light intensity appears in the digital display and the setting is complete. ON OFF Turn to + side Turn to side Threshold value Incident light intensity with object absent Threshold value Notes: 1) Scrolling display is not available in FX-31B/G/H. 2) The approx. 15 % amount of shift is the initial value. The amount of shift can be changed in the PRO mode from approx. 5 to 8 % (5 % step). Refer to the PRO Mode Operation for more details pertaining to setting instructions. 3) Do not move or bend the fiber cable after the sensitivity setting. Detection may become unstable. Please download the instruction manual from our website for setting of threshold value when used in combination with liquid level sensing fiber FD-F8Y and with pipe-mountable liquid level sensing fiber FD-F4. Threshold value fine adjustment Step Description Display Press MODE key to light up MODE indicator / ADJ (yellow). For FX-35(P), select either Output 1 or Output 2 beforehand, in case the threshold value is to be increased (sensitivity to be reduced), turn the jog switch to the + side to increase the threshold value slowly. If the jog switch is turned continuously to the + side, the threshold value increases rapidly. In case the threshold value is to be decreased (sensitivity to be increased), turn the jog switch to the side to decrease the threshold value slowly. If the jog switch is turned continuously to the side, the threshold value decreases rapidly. When jog switch is pressed, the threshold value is confirmed. Output operation setting Step Description Display Press MODE key to light up MODE indicator / /D ON (yellow). For FX-35(P), select either Output 1 or Output 2 beforehand, if the jog switch is turn to the + or direction, the output operation setting will change. When jog switch is pressed, the threshold value is confirmed. Timer operation setting or Displays present setting ight state Dark state Displays selected setting The setting for whether the timer is used or not can be done when MODE indicator / TIMER (yellow) lights up. For FX-31B/G/H, the timer type can be set in PRO mode. Further, an OFF-delay (initial value) which is useful when the response of the connected device is slow, etc., an ON-delay which is useful to detect only objects taking a long time to travel, and ONE SHOT, which is useful when the input specifications of the connected device require a signal of a fixed width, are possible with the FX-31 (-HS). FX-35(P) is also equipped with ON-delay OFF-delay and ON-delay ONE SHOT timers. Refer to the PRO Mode Operation for the setting method of the OFF-delay, ON-delay and ONE SHOT timer intervals. For the wind comparator mode teaching in FX-35(P), refer to the separately prepared PRO Mode Operation.
Digital Sensor SERIES 2 PRECAUTIONS FOR PROPER Refer to General precautions, p.8~ for fiber precautions, and to the PRO mode operation guide on our website for details pertaining to operating instructions for the amplifier. Wiring Make sure that the power supply is off while wiring. Verify that the supply voltage variation is within the rating. Take care that if a voltage exceeding the rated range is applied, or if an AC power supply is directly connected, the product may get burnt or damaged. If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground. In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground. Take care that short circuit of the load wrong wiring may burn or damage the product. Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction. Make sure to use an isolation transformer for the DC power supply. If an autotransformer (single winding transformer) is used, this product or the power supply may get damaged. Make sure to use the optional quick-connection cable for the connection of the amplifier. Extension up to total 1 m 328.84 ft is possible with.3 mm 2, or more, cable. (5-8 unit expansion: 5 m 164.42 ft, 9-16 unit expansion: 2 m 65.617 ft) However, in order to reduce noise, make the wiring as short as possible. Note that the residual voltage will increase when the cable is extended. Key-lock function If jog switch and MODE key are pressed for more than 2 sec. at the same time in RUN mode condition, the key operations are locked, and only the threshold value confirmation function or the adjust function (valid only when the adjust lock function is canceled) is valid. To cancel the lock function, press both the keys for more than 2 sec. once again. Note: 3 seconds or more for FX-31B/G/H(P). Others When the emission halt of the light emitting amount selection function is set from OFF to ON, the output may be unstable. Do not use the output control for.5 sec. after starting emission. Do not use during the initial transient time (.5 sec.) after the power supply is switched on. Take care that the sensor is not directly exposed to fluorescent lamp from a rapid-starter lamp, a high frequency lighting device or sunlight etc., as it may affect the sensing performance. Do not use this sensor in places having excessive vapor, dust, etc., or where it may come in contact with corrosive gas. Take care that the product does not come in direct contact with water, oil, grease, or organic solvents, such as, thinner, etc. This sensor cannot be used in an environment containing inflammable or explosive gases. Never disassemble or modify the sensor. Function table for series Previous models New models Standard type High-function type High-speed type Standard type High-speed type High-function type FX-31(P) (Previous version unit) FX-32(P) FX-33(P) FX-31(P) (Updated version unit) FX-31(P)-HS FX-35(P) Four-chemical emitting element + APC circuit No No No Yes Yes Yes Four-chemical emitting element only Yes (Note) Yes Yes ight emitting amount selection function No No No Yes Yes Yes Reduced intensity mode (S-D) Yes (Note) Yes No Yes Yes 9,999 digit display No No No No No Yes Response time (Max. speed) 15 μs 3 μs 9 μs 65 μs 35 μs 65 μs Interference prevention function (Effective no. of units) Incorporated (4) Incorporated (8) Not incorporated () Incorporated (4) Not incorporated () Incorporated (16) Independent 2 outputs No No No No No Yes Alarm output function No No No No No Yes Error output function No No No No No Yes Differential sensing No No No No No Yes Window comparator mode No Yes No No No Yes Peripheral units that can be combined Bank selection unit FX-CH(-P) External input unit FX-CH2(-P) Upper communication unit SC-GU1-485 Yes Yes No No No No No No No Yes No Yes No No No Yes No Yes Note: Except FX-31B/G/H.
21 Digital Sensor SERIES PRECAUTIONS FOR PROPER Refer to General precautions, p.8~ for fiber precautions, and to the PRO mode operation guide on our website for details pertaining to operating instructions for the amplifier. A difference between the updated version unit and the previous version unit for FX-31(P) (Red ED type) The product has been modified as shown below since its production in June 24. Changes in appearance Top view Side view Before change Name plate Display Uses special parts * NAVI is printed only on the both sides Top view Side view After change Added to name plate Change in shape of jog switch * NAVI is printed only on a side Checking minor changes between previous and updated models can be done by checking whether the printing is on both sides or only one side. Upgraded functions 1. Response times added An ultra high-speed mode (H-SP) has been added to the existing 4 response time modes [high-speed (ST), reduced intensity (S-D), standard () and long range (ONG)]. This is changed using in 4 steps Before change 15 μs (ST) 25 μs (S-D) 25 μs () 2 ms (ONG) 5 steps After change 65 μs (added) (H-SP) 15 μs (ST) 25 μs (S-D) 25 μs () 2 ms (ONG) Changes in operation 1. Timer selection method Previous version unit: Timer type was changed using PRO1 mode. The TIMER setting in NAVI mode could only be turned on or off. After change: The type of timer can be changed using the TIMER function in NAVI mode. 2. Checking threshold value in RUN mode The threshold values can be checked by turning the jog switch. Display changes 1. Checking blinking of sensitivity surplus The stable surplus display method after teaching has been changed. Previous version unit: Sensitivity surplus is indicated by the number of blinks of the stability indicator. After change Digital display only 2. Initial direct code value changed The factory default settings for the direct codes have been changed. Previous version unit After change 4 * The default setting for the timer period is 1 ms, and the direct code for 1 ms is 4, so this has been changed. Internal circuit changes 1. Addition of an APC circuit A four-chemical emitting element which provides stable sensing over long periods has been added, as well as an APC (Auto Power Control) circuit that improves stability during short periods. Cautions on sensor connection in cascade When connecting the previous version unit (including FX-31B/G/H) and updated version unit to be used in a cascade, refer to Cautions on sensor connection in cascade. 2. Extension of timer period The setting range for the timer period was previously 5 ms, but this has been extended to a new range of 9,999 ms. 3. ight emitting amount selection function The light emitting amount can be changed to one of 4 levels (5 levels when emission halt is included). 4. Backup, copy lock and key lock functions added Backup: This selects whether or not threshold values set by teaching are written to (stored in) an EEPROM. Copy lock: This selects whether copy function and data bank function communication are possible or not. Key lock: This disables input using switches to prevent accidental changing of settings.