Tools and Cable Management 43046A THIRD HAND WITH MAGNIFYING GLASS AND SOLDERING IRON OWNER, 10.80 +VAT The classic must for each electronics engineer. The third hand consists of a hand magnifier, 2 alligator clips, a sponge and has a soldering iron holder and is thus the universal aid for soldering work WZ0034 LOGILINK 3RD HELPING HAND WITH MAGNIFIER 6.75 +VAT For Close-up Work Set and hold your work at any angle Magnifying glass for close inspection Heavy cast iron stand with 8 articulated joints, two flexible clamps Glass magnifier: Ø46 mm 43086 TABLE VISE FOR HOBBY AND HOME IMPROVEMENT 13.50 +VAT Table vise for hobby and home improvement, for bolting to table edges up to 22mm thickness. Opening up to 45mm, Jaw width 60mm 43039 5 COLORS ELECTRICAL TAPE, 18mm X 9m 3.38 +VAT 43048 ELECTRONIC SCREWDRIVER ASSORTMENT, 15 PCS 10.80 +VAT Electronic Screwdriver assortment, 15 pieces Slot: 1,0 / 2,0 / 3,0 / 3,5 mm Phillips: PH000, PH0, PH2 Torx: 6, 8, 10, 15 Wrench: 1,5 / 2,0 / 2,5 / 3,0 mm in a handy case 43011A PRECISION SCREWDRIVER WITH RATCHET AND MINI BITS, 12PCS. 17.55 +VAT Slotted: SL2, SL2.5, SL3 mm Phillips PH00, PH0, PH1 Torx: T6, T7, T8, T9, T10 43063 ELECTRONICS PLIERS, SIDE-CUTTING PLIERS 6.75 +VAT Rubber-coated handles for secure grip, 2-colored Perfect for electronics work and DIY hardened steel nickel-coated and polished blades prevent rusting precise cutting / gripping tool for clean work 43014 12-IN-1 SPECTACLE SCREW DRIVER SET 12.83 +VAT Small screw driver set, well suited for repairing spectacles. Set includes: 1 screwdriver handle 3 philips insert bits: PH000, PH00, PH0 3 slot insert bits: 1.5, 1.7, 2.0 5 hexagon insert bits: 2mm, 2.3mm, 2.4mm, 2.5mm, 2.6mm 1 outer Torx insert bit: TN8 in synthetic leather bag
43035A MULTIBITBOX 100-PCS, WITH SPECIAL BITS 18.90 +VAT 5 Adapter bits 3x clip bits 1, 2, 3 3x TORQ bits 6, 8, 10 3x internal multi-tooth bits M5, M6, M8 4x TRI WING bits 1, 2, 3, 4 4x internal square bits S0, S1, S2, S3 4x Security Screws Bits 4, 6, 8, 10 9x flathead bits 3, 4, 4.5, 5, 5.5, 6, 6.5, 7, 8mm Philips 8x bits PH0, PH1, PH2, PH3 5x POZI-DRIVE bits Z0, Z1, Z2, Z3 9x internal hex bits 1.5, 2, 2.5, 3, 4, 5, 5.5, 6, 8mm 10x internal hex bits 1 / 16 ", 5 / 64", 3 / 32 ", 7 / 64" 1 / 8 "9 / 64", 5 / 32 ", 3 / 16", 7 / 32 ", 1 / 4 " 6x internal hexagon Safety Metr.Bits 2, 2.5, 3, 4, 5, 6mm 6x internal hex bits Safety inch 5 / 8 ", 3 / 32", 7 / 64 ", 1 / 8", 9 / 64 ", 5 / 3" 9x 9x Torx bits and Torx bits Safety T8, T10, T15, T20, T25, T27, T30, T40, T45 43011 PRECISION SCREWDRIVER-SET 28 PARTS 25.65 +VAT Bits for slotted screws: SL1.5, SL1.7, SL2, SL3, SL4 Bits for cross-head screw: PH000, PH00, PH0, PH1, PH2 Bits for Torx screws: T5, T6, T7, T8, T9, T10, T15, T20 Bits for hexagonal screws (in mm): 3, 3.5, 5, 4.5, 5, 5.5, 6 Bits for three-edged screws: external and internal with extension und rotary-power adapter in handy box WZ0023 TOOL SET LOGILINK 7.43 +VAT Incl. transport box 6x micro screwdrivers 1x micro cutter 1x mini telephone plier 1x bit screwdriver with extension 10x bits (PH1, PH2, PZ1, PZ2, PZ5, PZ6, T10, T15, T20, adaptor) 4x socket wrench (5mm, 6mm, 8mm, 10mm) 1x tweezers 43018B TOOL KIT FOR COMPUTER AND ELECTRONICS, 9 PCS. 22.95 +VAT 3 slot screwdrivers, various sizes 3 Philips screwdrivers, various sizes 1 side cutter 1 needle-nosed pliers 1 tweezers 66407C LAN SERVICE TOOL KIT Remote cable Tester for RJ45(8P8C) / RJ11(6P6C)/ USB / 1394 / BNC Adjustable impact punch down tool, with 110 blade Modular crimping tool for 8P8C/RJ-45, 6P6C/RJ-12 and 6P4C/RJ-11 6" Diagonal plier 6" Long nose plier 5" Electrician scissor 6" Wire stripper/cutter 7 pcs folding type hex wrench Plastic color torch 6" adjustable wrench 9 pcs mini combination wrech (8,9,10,11,12,13,14,15,16mm) 16 pcs super torque ratchet driver set includes: Changeable shank ratchet drive.philips bit shanks: #0, 1, 2. Slotted bit shanks: 1/8, 3/16,1/4.Sockets: 4, 5, 6, 7, 8, 9, 10, 11, 12, 13mm (3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 15/32, 1/2), 2 in one mini screwdrier Universal stripping tool, Telephone line tester, 6P4C modular plug adaptor, Zipper vinyl bag
43017B TOOL CASE, ALUMINUM SILVER, LOCKABLE 41.85 +VAT Tool case made of aluminum Color: aluminum / silver unequipped without content lockable Interior with assortment depositors and classification, customizable covered with foam External dimensions approximately 45 x 33 x 15.5 cm 43004I VOLTAGE TESTER UPTO 380VOLT 8.10 +VAT With voltage and polarity display Voltage range: 6-400V AC Display elements: 6-12-24-50-110-220-380V LED Frequency range: 50-500 Hz 43005D DIGITAL MULTIMETER WITH ACOUSTIC CONTINUITY TESTER, 18.90 +VAT BUMPER STRIP 3 1/2-digit LCD display with blue background illumination. rotary switch with 19 positions for function and area setup, automatic out-of-range indicator, polarity indicator, continuity tester, Data-Hold, background illumination (Back Light), diode /transistor test hfe, touch protected 4mm jacks. DC voltage: 200mV DC / 2VDC / 20VDC / 200VDC / 600VDC (±0.5%) AC voltage: 200VAC / 600VAC (±1.2%) DC current: 2mA ±1% / 20mA ±1% / 200mA ±1,5% / 10A ±3% Resistance: 200 Ohm / 2kOhm / 20kOhm / 200kOhm ±1% / 2M-Ohm ±1,2% Continuity tester with buzzer Case color: yellow with yellow protective rubber frame Power supply: 9V battery block WZ0015 CABLE TESTER WITH REMOTE UNIT LOGILINK 13.50 +VAT For testing of network cables Suitable for RJ45/RJ11/RJ12 & BNC, 10Base-T, 10Base-2, 258A, TIA and 568A/568B Token Ring cable Automatic or manual scan Master and remote unit for testing remote cable Check the grounding Display status of the cable, Continuity, wiring fault WZ0014 CABLE TESTER 5-IN-1 WITH REMOTE UNIT 28.35 +VAT The WZ0014 5 in 1 Cable Tester tests 5 common LAN and Computer cables. It tests installed cables or patch cords with RJ-11, RJ-45, USB, IEEE1394 and BNC connectors. It is intended to test cables with straight through connections not cables with reversed, or transposed connections like some LAN crossover cables, or reverse wired telephone cables. Test 5 types of RJ-11, RJ-45, BNC, USB and IEEE1394 cables Simple one button test Ergonomic portable handheld design Tests installed wiring or patch cables Remote unite stores in Main Unit 600 ft test distance for RJ-45/RJ-11/BNC Convenient battery access Built in battery test LEDs indicate connections and faults Beeper provides audible annunciation of test results Tests shielded (STP) or unshielded (UTP) LAN cables Test shields in IEEE1394 and USB cables. Carry bag inclusive. Color: red
WZ0012 NETWORK TOOL SET 24.30 +VAT Network Tool Set composed of: 1x LSA Punch Down Tool WZ0001A 1x Modular Crimping Tool 8P8C WZ0004 1x Stripper Tool WZ0005 1x Cable Tester for RJ11&RJ12&RJ45 WZ0010 H56712A HOBBES CABLETRACER PROBE 70.20 +VAT The Hobbes Probe is equipped with a tone amplifier and an LED indictor that detects audible frequency tones for accurate tracing and identification of wires. It s plastic conductive tip prevents shorting of expensive telecom and network equipment. Features: Special inductive plastic tip, which prevents accidental shorts (possible with copper-tip tracers) when using near high voltage devices. Traces and identifies wires or cable in a bundle or group without damaging cable insulation. Adjustable volume level for various work environments Both amplifier and LED for loud or dark work environments. Can work with any existing analog tone generator in the market. Power switch to prevent battery drain. Specification: Power Source: DC 9V battery x 1pcs Power Consumption: 90 ma Humidity: 0 to 95% (non-condensing) Dimensions: 234 x 32 x 37 mm Approx. Weight: 85g WZ0016 WIRE CUTTER 5.40 +VAT The angled cutting pliers from LogiLink is ideal for stripping and cutting of 20-24 AWG wire. The cutter is angled 45 degrees and has insulated handles. A spring simplifies operation 74101A UNIVERSAL CABLE CUTTER AND WIRE STRIPPER 10.80 +VAT FOR PATCH AND COAX Universal cable cutter and wire stripper, suitable for patching and coaxial cable. The cable cutter Duch separates patch cables and coaxial cables up to a diameter of about 6mm. Furthermore, can be removed with this tool in a simple way the cable sheath. WZ0003 CRIMPING TOOL UNIVERSAL WITH CUTTER AND ISOLATER METAL 16.20 +VAT Multifunctional Modular Tool for crimping cables for network and telephone Smooth-running cable cutter Easy cable stripping Crimping tool for 8P8C-RJ45, 6P6C-RJ12 6P4C-RJ11, 4P4C, 4P2C, DEC shielded 8P8C-RJ45 Modular Plugs Blade cover lever action HQ Metal WZ0004 CRIMPING TOOL FOR RJ45 WITH CUTTER METAL 6.75 +VAT Modular Crimping Tool Suitable for 8P8C RJ45 plugs Smooth-running cable cutter Easy cable stripping Blade cover Rubbered, non-slip plastic handles Tool made of high-grade metal
WZ0001A LSA PUNSH DOWN TOOL 6.75 +VAT LSA Punch Down Tool Suitable for on-wall and in-wall wallplates Cutting of the extending cable end in one step According to the standard EIA/TIA 568 B For Network, DSL and ISDN 74220 LSA TECHNOLOGY INSERTION TOOL 56.70 +VAT The standard tool for all data, information and telecommunications cabling. Applicable for all LSA Technology series and RJ45 jacks and HIGHBAND. For connecting conductor diameters (from 0.35 to 0.9 mm) and core diameters (from 0.7 to 2.6 mm). In a wiring of a second wire in contact, the sensor is switched off (core specification and number of cores depends on used connection technology). The gap can be switched off to allow a loop through a potential on adjacent contacts. Lifetime: 0.4 mm: 200.000 wirings, 0.6 mm: 100.000 wirings, 0.8mm: 50,000 wirings Aderendlage scanning (sensor) scissors/cutting lock/pull hook/blade WZ0005 ISOLATION AND CUTTING TOOL FOR PATCHCABLE 3.38 +VAT Universal Cable Stripping Tool Suitable for patch- and raw cables Blade cover Tool made of high-quality plastic Integrated cable cutter 43031A ALL-ROUND CUTTER KNIFE, 18mm BLADE, WITH 3 BLADES 4.73 +VAT Multi-use knife with break-off blade, plastic model with robust handle and metal guide 18mm blade with metal guide incl. 2 replacement blades PW-342 BITSET 31-PCS FOR QUICKLOADER CASE 31.05 +VAT WITH BELT TIE-CLIP 5 x Phillips, 5 x slot, 3 x Pozidrive, 7 x Torx, 10 x female hexagon Phillips: 0/1/2/2R/3 slot: 3/4/5/6/8 Pozidrive: 1/2/3 Torx: T10/T15/T20/T25/T27/T30/T40 female hexagon: 1,5/2/2.5/3/4/5 6/7/8/10 KAB0039 LOGILINK CABLE FASTENER SET 2.70 +VAT Cable mounting with double-sided tape For mounting on smooth surfaces Suitable for organizing cables Easy opening and closing the cover Easily attaches to tables, boards and corners In Box 10 Cable holders in 3 styles Color: Black KAB0013 CABLE SPIRAL WRAPPING BAND, 2.50m LOGILINK 25mm 6.41 +VAT The spiral tube from LogiLink bundles cables and protects cable reliable. The flexible cable tube is durable and reusable. The supplied installation tool simplifies the bundling of cables. The spiral tube cable tie is the space-saving option for a clean installation of cables and reducing trip hazards. Bundles and reliably protects cable Flexible cable tube Durable and reusable Dimensions: 2500 x 25 mm Incl. installation tool Color: Grey
KAB0014 CABLE SPIRAL WRAPPING BAND, 1.50m LOGILINK 28mm 5.06 +VAT The spiral tube from LogiLink bundles cables and protects cable reliable. The flexible cable tube is durable and reusable. The supplied installation tool simplifies the bundling of cables. The spiral tube cable tie is the space-saving option for a clean installation of cables and reducing trip hazards. Bundles and reliably protects cable Flexible cable tube Durable and reusable Dimensions: 1500 x 28 mm Incl. installation tool Color: Grey 59947S INLINE SPIRAL WRAPPING BAND 10m, BLACK, 15mm 12.83 +VAT The flexible cable channel of InLine makes it easy to combine several cables, wires, strands into a coil. The conduit may be simply wrapped around the collar and can be cut to custom length with scissors or knife. Inside diameter: 14mm, Outside diameter: 15mm Suitable for Federal-Diameter of about 15-20mm incl. Hand Tool 59947T INLINE SPIRAL WRAPPING BAND 10m, BLACK, 20mm 16.20 +VAT The flexible cable channel of InLine makes it easy to combine several cables, wires, strands into a coil. The conduit may be simply wrapped around the collar and can be cut to custom length with scissors or knife. Inside diameter: 19mm, Outside diameter: 20mm Suitable for Federal-Diameter of about 20-25mm incl. Hand Tool 59947U INLINE SPIRAL WRAPPING BAND 10m, BLACK, 28mm 17.55 +VAT The flexible cable channel of InLine makes it easy to combine several cables, wires, strands into a coil. The conduit may be simply wrapped around the collar and can be cut to custom length with scissors or knife. Length: 10m Color: black Inside diameter: 26mm, Outside diameter: 28mm Suitable for Federal-Diameter of about 28-35mm incl. Hand Tool 59965G INLINE CABLE TIE MOUNTS, 0.61 +VAT ADHESIVE, 20X20mm, BLACK, 10pcs