Xsarius Satmeter Pro Manual 1
2
Directory of content Introduction Directory of content 3 Introduction 3 Satmeter Pro 02 Frontpanel & buttons 6 Xsarius provides high quality products that enable you to enjoy digital television. This also applies to the Xsarius Satmeter Pro. Your satellite dish is setup precisely and accurately in no time. In this manual you will find instructions for 3 models. The Satmeter Pro 02, 06 and 08. Quick manual 8 Using the menu 9 Channel 1.1 Channel 9 1.2 Add a channel 10 Installation 2.1 Autoscan 12 2.2 Add satellite 12 2.3 Delete satellite 13 System 3.1 Language settings 13 3.2 TV system 13 3.3 Auto-shut-down 13 3.4 OSD instellingen 13 Tools 4.1 Information 14 4.2 Satellite guide 14 4.3 Default value 14 4.4 Software upgrade 14 Specifications Satmeter Pro 02 15 Before using the Xsarius Satmeter Pro the battery needs to be fully charged (+/- 8 hours) to ensure a long life span. 3
Satmeter Pro 02
Satmeter Pro 02 Frontpanel and buttons 1 20 21 2 5 5 3 4 9 6 8 11 10 6 7 13 14 15 16 19 12 17 18 6
1 Signal input Input satellite dish 2 3,5 inch LCD display Display for the menu and TV channels 3 Signal indicator (LED) Signal indicator. Lights up when meter receives signal 4 Power indicator (LED) This indicator is green when the Xsarius Satmeter Pro 02 is switched on. If the meter is being charged this LED light will be red until the battery is fully charged. When the battery is fully charged the indicator turns green again. 5 13/18 V indicator Indicates 13V/18V setting 6 F1, F2, F3, F4 Function buttons 7 Navigation ( ) Use the navigations buttons to move your cursor 8 OK Confirmation button 9 Menu Press to display the main menu on the screen 10 Exit To cancel your selection or to move back to the previous menu 11 12 13 0-9 buttons PAUSE MUTE Press to enter required numbers in the input box Press pause to pause your programme. Press pause again to continue your programme. Press to temperarity cut off the sound of the program 14 SCAN Press to enter the Auto Scan menu 15 SAT Press to display the satellite list of searched channels 16 TV/R Press to switch between television and radio channels 17 INFO Press to show information of the current channel 18 USB port Connect to PC to upgrade 19 Charge port To connect with the charger cord. 20 On/Off switch To switch the Satellite meter on and off 21 AV IN/OUT Input/output audio and video signal 7
Quick manual Connect the Satmeter Pro 02 to your satellite dish and switch on the meter. Press the Menu button to open the menu. If their is no desired channel list set up, continue to the next step (step 1). In case a desire channeld list is already set up continue this quickmanual at step 2. 1 Creating a desired channel list (A) Open the main menu and select the option Add Channel. Now press OK. Use the navigation buttons ( ) to select the option Edit Satellite. Fill in the LNB parameters. Press Exit or Menu to head back to the previous menu. In case their are already useable transponders available select the desired parameter. To add a transponder select the option Add TP in the menu. Your required to fill in the TP Frequency, Symbol rate and polarity. (B) The Xsarius Satmeter Pro 02 shows the signalstrenght and quality. Setup your satellite dish based on the information the Xsarius Satmeter Pro provides. Your satellite dish is aligned properly when both signal strenght as quality indicates max. (Note! Signal intensity needs to be set to maximum when you align your satellite dish) 2 Selecting the desired channel list Select the desired channel list. Use the navigation buttons ( ) to select a channel. Now press the Info button to show information about the selected channel. If the signal strength and quality are not optimal, you can follow step 1B. Check if the the LNB frequency is correct before proceeding to step 1B. 8
Using the menu Once the Satellite Meter Pro is installed and the cables are connected, press Menu to open the mainmenu. The mainmenu has 4 options. Channel, Installation, System and Tools. Use the navigation buttons ( ) to select one of these options. Press OK to confirm your choice. Press exit at any time to exit the menu you ve opened. Channel 1.1 Channel In the submenu channel your able to manage the stored channels. You can edit, lock, pass over or delete radio and tv channels easily. To edit channels press Menu. You are now in the main menu. The option channel will be marked. Select TV Channel to edit TV channels. Select Radio channel to edit radio channels. Use the navigation buttons ( ) to make your selection. The edit menu will now appear. Deleting a channel Press 1 and select the channel you wish to delete. Press Ok to confirm your selection. The selected channel will now be marked with a X symbol. Select a marked channel and press OK once again to actually delete the channels that are marked. Press exit to confirm the changes. A confirmation message will show up. In case you want to undo the changes select Cancel and press Ok. Moving a channel Press 2 and select the channel you wish to move. Press Ok to confirm your selection. The channel will now be marked with a symbol. Use the navigation buttons ( ) to indicate where you want the selected program. Press ok to confirm the new location. Repeat this steps if you want to move more channels. 9
Add a channel to one of the 6 favorite lists Select the channel you would like to add add to your favorite lists. Press 3 to open the favorites submenu. Select one of the six favorite lists and press OK. The selected channel will be marked with a symbol. Repeat this steps if you want to add more channels to your favorite lists. Edit a Channel Select the channel you would like to edit. Press 4 to open the edit submenu. Use the navigation buttons ( ) to make your selection. Use the (0-9) buttons to enter numerical values. Select Save to confirm the changes. Press Exit to undo the changes and move to the previous menu. Changing satellite Press the SAT Button. Use the navigation buttons ( ) to select one of the stored satellites. The Channellist shows all channels received by the current satellite. Press OK head back to the channellist. 1.2 Add a channel Open the Channel menu and select the option Add channel. Press Ok. Satellite: TP Transponder: TP Frequency: Symbol rate: Polarization: Search: Press Ok to open the list with satellites. Use the navigation buttons ( ) to select the satellite you would like to check. Select the desired transponder Use the (0-9) numerical buttons to fill in the transponder frequency Symbol rate of the transponder Vertical or horizontal polarization Select the desired option 10
Edit satellite Satellite: Press OK to show a list of satellites. Select the satellite you wish to edit by using the navigation buttons ( ). LNB Type: Select the LNB type your using. LNB Freq (1,2): Fill in the correct frequency of the LNB s your using. LNB Power: Select the desired power setting. 22K: 22K: 22KHz control is automatically set for each LNB alternative. If universal is selected, 22KHz control should be switched off. DiSEqC: Select the port number to receive the RF signal from the LNB that is connected to your DiSEqC switch. Positioners: When your satellite dish is not aligned properly you won t receive any signal. The STB provides DiSEqC1.2 correct information that enables you to align your satellite dish correct. Satellite: TP: Postion no. & Save Limit setup: Movement: Continuous move Recalculation: Select the desired satellite. Select the desired transponder Select the position No. or null. Setting of limits for the antenna. The satellite can now be turned into the desired direction using the navigation buttons ( ). The satellite can be continuous moved to the desired direction. Press OK to recalculate Go to referance: Add TP: Delete TP: A focus point while searching a satellite can be selected by pressing OK. Add a new transponder to the selected satellite Delete the current transponder 11
Installation 2.1 Autoscan (1) Select autoscan and press OK to open the autoscan menu. (2) Press OK to open the satellite list. Now select the satellite you would like to scan for. Your selection will be marked with a X symbol. Select the desired modus and press OK to start automatic scanning. It is also possible to reset the current satellite by opening the Edit Satellite menu. 2.2 Add satellite Satellite: Press OK to open the submenu. give the satellite your about to add a name. Press menu to close the current menu. LNB Type: Select the LNB type your using. LNB Freq (1,2): Fill in the correct frequency of the LNB s your using. LNB Power: Select the desired power setting. 22K: 22Khz wordt automatisch ingesteld voor elke alternatieve LNB. Wanneer Universeel is geselecteerd dient de 22K modus uitgeschakeld te zijn. 22K: 22KHz control is automatically set for each LNB alternative. If universal is selected, 22KHz control should be switched off. DiSEqC: Select the port number to receive the RF signal from the LNB that is connected to your DiSEqC switch. 12
2.3 Delete satellite (1) Select Delete satellite and press OK (2) Select the satellite you wish to delete and press OK (3) Repeat step 2 for every satellite you wish to delete (4) To confirm your changes press Exit (5) You will now be asked to confirm the changes. Use the navigation buttons ( ) to cancel or confirm. System 3.1 Language settings Select the desired language for the menu s 3.2 TV System You can set the TV type by using the navigation buttons ( ). If the source program is PAL, TV set PAL. If the source program is NTSC, TV set NTSC. 3.3 Auto-shut-down To set a timer for automaticly shutting down the Satmeter Pro. 3.4 OSD settings Menu color: Transparancy: Parent lock Allows you to select the desired color for menu. You can adjust the transparency level by using the navigation buttons ( ) From 0% to 80%. This function allows you to lock the channel with a password in order to prevent children from accessing the channel. You can also protect your installed data and information using the Install Lock. If the STB Panel Lock item is set to OFF, the keys of the front panel is invalidation. The default password is 0000. When the correct password is entered, the selected menu opens automatically. 13
Tools 4.1 Information Here you will find information about the current channel 4.2 Satellite guide. The Satellite guide will help you with setting up your dish. Local longitude: Enter your local longitude Local latitude: Enter your local latitude Satellite longitude: Enter the longitude of the satellite you wish to align with. Start: Press OK. Information will be provided for setting up your satellite dish. 4.3 Default Value This option allows you to restore the parameters to the original state. Be careful when you use this option, because you can lose data. 4.4 Software upgrade You can upgrade software via the RS-232 serial port. Upgrade Mode: Select the desired upgrade mode. 14
Specifications Satmeter Pro 02 System capacity DVB-S Compliant Ja LNB input Connector F type, Female Frequency range Signal level LNB power LNB Switch control 950 MHz ~ 2150 MHz 66dBm ~ 25 dbm 13/18 V, Max 350 ma 22 KHz DisEqC Ver. 1.0 Demodulator Front end QPSK Demodulation range SCPC en MCPC compliant Spectral inversion 2Mbps ~ 45 Mbps yes Auto conversie System Processor 32 bit processor (200 Mhz) FLASH SDRAM 2Mbyte 16Mbyte Video decoder MPEG 2 MP@ML Data rate Max 15Mbits/s Resolution 720 x 576, 720 x 480 Videoformat PAL/ NTSC/ SECAM Audio MPEG MPEG 1 & 2 Type Sampling Rate Mono 32,44.1 & 48 KHz Data Connection USB Power LI-ION accu 3000 mah / 8.4 V max Supply voltage 12 Volt Charger 90-240V Properties Size 9.5 x 15.5 x 4.5 (cm) Weight 0,5 KG 15
www.xsarius.com 36