SCIR. Infrared Illuminator Powerful Indoor/Outdoor IR Spotlight SCIR

SCIR Infrared Illuminator Powerful Indoor/Outdoor IR Spotlight The NetMedia SCIR Infrared (IR) Illuminator provides night vision for IR (850nm) sensitive cameras. It enables cameras such as NetMedia s B/W and Day/Night color models to see in complete darkness. It mounts to a typical round 4 inch junction box. Other junction boxes from your local hardware store may also be used after replacing the round base with another that has a 1/2 inch diameter hole for the elbow bracket. Product Includes: 1. Illuminator Assembly (IR LED s, IR Passing Filter, Housing, Housing Cap, Elbow Bracket, Locking Ring, Base, Gasket, Power Connector). 2. 12V DC 300mA Power Transformer, Center Conductor Positive. 3. Mounting Screws. Housing Available in ivory. Elbow Bracket Adjusts illuminator angle at base, screw, and housing. IR Passing Filter Hides LED s in daytime. IR Illuminators Behind IR Passing Filter - 850nm IR LED s provide night vision for IR sensitive cameras. Housing Cap Protects illuminator. Power Connector 12V DC 300mA, center positive. Gasket, Base & Screws Mount to round 4 junction box. Locking Ring Secures elbow bracket to base at desired position. DO NOT CUT OR SPLICE THE ILLUMINATOR S CABLES. MODIFYING THE UNIT IN ANY WAY WILL VOID THE WARRANTY. Installation Procedures: 1. Connect the 12V DC 300mA Power Transformer from an AC outlet to the Illuminator s Power Connector. 2. Mount the base to the junction box (not included) and adjust the Illuminator Assembly for proper lighting. Check camera to ensure that the desired area is illuminated without shining, either directly or by reflection, into the camera lens. When satisfied, secure all adjustment points. FEATURES Lets cameras see in complete darkness Works with NetMedia B/W & Day/Night cameras Provides 30 degree spot light up to 50 feet Weather resistant enclosure Internally routed cables Mounts directly to walls and ceilings Mounts to standard electrical fixtures Tamper resistant wiring Includes power supply 1 year limited warranty SPECIFICATIONS Infrared Illuminators: Illumination Range: Power Requirement: Power Connectors: Housing Size: Base Size: Base Mounting Holes: Assembly Weight: 64-850nm LED s 30 degree spot up to 50 ft. 12V DC 300mA Female 5.5mm OD, 2.1mm ID, center positive 3.13 dia. x 4 long 4.5 dia. x 0.75 high x 0.5 hole 3.5 centers 1 lb. (subject to change without notice) SCIR MAN-SCIR

NM-IRJBOX Infrared Illuminator No visible light or red glow The NetMedia IRJBOX Infrared (IR) Illuminator provides invisible light for IR (940nm) sensitive cameras. It enables cameras such as NetMedia s SC53 to see in complete darkness. The illuminator mounts in a wall with its bracket or in a typical single gang junction (light switch) box. It is concealed behind a black cover plate insert that allows only IR to pass. For best results, do not mount in the same junction box as the camera. Product Includes: 1. IR Illuminator Board (IR LED s, Power Y-Cable). 2. 12V DC 300mA Power Transformer, Center Conductor Positive. 3. Black Lens Cover Insert. 4. Mounting hardware (Bracket and Screws). Lens Cover Black insert conceals Illuminator, snaps into Cover Plate. IR Illuminator Board 940nm IR LED s provide invisible light for camera without red glow. Power Y-Cable provides female input and male output for 12V DC power. Mounting Bracket Installs in Wall Cutout. Illuminator also mounts in a junction box. Cover Plate Not Included Wall Cutout Not Included Installation Procedures: 1. Connect the 12V DC 300mA Power Transformer from an AC outlet to the Illuminator s Power Input Connector. If sharing power through the Y-Cable, make sure there is enough current for both devices; the Illuminator requires 200mA. 2. Install Illuminator Board into Mounting Bracket or Junction Box (not included). Check camera to ensure that the desired area is illuminated without shining, either directly or by reflection, into the camera lens. 3. Snap the Black Lens Cover into the Cover Plate (not included) by pressing all four corners in simultaneously. If necessary, the square corners of the insert may be slightly rounded. 4. Attach the Cover Plate to Mounting Bracket or Junction Box. Silicon or similar sealant may be used as needed. FEATURES Lets cameras see in complete darkness Works with NetMedia Day/Night color cameras No visible red glow Wide angle of IR dispersion Built-in Y-Cable for sharing power Mounts in standard electrical fixtures Includes Mounting Bracket Includes power supply 1 year limited warranty SPECIFICATIONS Infrared Illuminators: Illumination Range: Power Requirement: Power Connectors: Mounting Holes: Size: Weight: 64-940nm LED s Up to 6 ft. 12V DC 200mA 1 Male, 1 Female 5.5mm OD, 2.1mm ID, center positive 3.8 centers 4.25 long x 1 wide x 0.2 thick 0.8 oz. (subject to change without notice) NM-IRJBOX MAN-IRJBOX

NM-ACB3 Cable Box Bypass Kit Passes modulated signals directly to TV Use the NetMedia ACB3 Cable Box Bypass/Combiner Kit to pass a modulator signal to the TV tuner without disrupting the output of a digital or analog cable box. Most cable boxes will only tune cable service signals. Therefore, the TV must be used instead of the cable box to tune other signals. The ACB3 permits this by splitting the cable signal and filtering out channels 3 and 4 before recombining with the cable box which outputs an independent channel 3 or 4. Product Includes: 1. Bypass Filter Assembly (2 Two-Way Splitters, Male to Male F-Connector Coupler, Bypass Filter). 2. Mounting Screws. To Cable Box Sends signal to Cable Box RF Input. Cable Box Not Included - may be analog or digital box. From Cable Box Receives signal from Cable Box RF Output. From Wall Receives combined cable and modulator signal from distribution system. Bypass Filter Removes channels that would interfere with cable box output on channels 3 and 4. To TV Sends Cable Box Output and filtered bypass signal to TV RF Input. Installation Procedures: 1. Set the modulator according to its directions. Choose an unused channel with at least one blank channel on either side to separate it from any other broadcast, cable, or modulated sources. Be aware that digital cable data typically interferes with channels above 80, even though they appear unused, and even when the location is not subscribed to digital services. Channels 120-125 sometimes work without filtering; any filter required to clear a channel range from the main cable service would be separate and in addition to the one included with the ACB3 (NetMedia CNF7080 removes cable channels 70-80). Also, the TV analog channels 120-125 are not the same as the cable box digital channels 120-125 so they will not interfere with each other. 2. Combine the modulator and cable service at the beginning of the distribution system. This should be before any other splitters except for ones that are dedicated to Internet service. Make sure not to use any diplexers to split or combine because they will severely degrade whichever signal is connected to the SAT input/output. 3. Install an ACB3 Kit as shown above wherever there is a cable box that is connected to the TV s only RF cable/antenna input. 4. Use the cable box tuner/remote to view cable programming while the TV is set to channel 3 or 4. Use the TV tuner/remote to switch it to the modulator channel. FEATURES Lets TV tune to modulator channels Works with analog and digital boxes Prevents conflict on ch. 3 and 4 Sturdy compact design 1 year limited warranty SPECIFICATIONS Filtered Frequencies: Filtered Channels: Input/Output Connectors: Cable Type: Size: Weight: < 91MHz VHF 2-6 4 Male F, 75 Ohm Coax such as RG59 or RG6 5.5 long x 2 wide x 1 high 3.3 oz. (subject to change without notice) NM-ACB3 MAN-ACB3

One Year Limited Warranty NetMedia, Inc. warrants this product to be free from defects in materials and workmanship under normal use and service for One Year from the date of purchase or NetMedia will repair or, at its option, replace the defective product. Please keep your purchase receipt. In the unlikely event that you need warranty service, call NetMedia at 1-520-544-4567 for a Return Material Authorization (RMA) number. Then, return the product, with the RMA number clearly marked on the package, by a traceable method with freight pre-paid and accompanied by a copy of the purchase receipt to: Attn: Customer Service, NetMedia, Inc. 10940 N. Stallard Place, Tucson, AZ 85737-9527 No expressed or implied warranty is made for any defects in this product which result from accident, abuse, failure to operate the product in accordance with relevant instructions, neglect, immersion in or exposure to chemicals or liquid, extreme climate, excessive wear and tear and defect resulting from other extraneous causes such as unauthorized disassembly, repair and or modification. Any implied warranty arising from the sale of this product, including implied warranties of merchantability and fitness for a particular purpose, are limited to the warranty stated above. NetMedia shall not be responsible for any loss, damages or expenses, whether direct, consequential or incidental that arise from the use or inability to use this product. Some states do not allow limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from state to state. Frequently Asked Questions Q- Do I need the bypass kit if I use the A/V cables to connect the cable box to the TV? A- No. You only need the kit when you use the coax output of the cable box. Split the coax before the cable box. Connect the cable box to the TV s A/V input and the bypass coax to the the TV s RF input. Use the TV remote to switch the TV from the A/V input to the modulator channel. Q- Do I need the bypass kit if the TV has two coax inputs? A- No. You only need the kit when you use must combine the coax output of the cable box with the bypass coax in order to go into the same input of the TV. Split the coax before the cable box. Connect the cable box output to one RF input and the bypass coax to the other RF input. Use the TV remote to change RF inputs on the TV (ANT1, ANT2) and then select the modulator channel. Q- Why can t I see the modulator on the cable box, even after I installed the bypass kit? A- Most cable boxes are setup to only tune the cable company s channels. The purpose of the bypass kit is to send the modulator signal directly to the TV for tuning. Therefore, you will have to use the TV s remote instead of the cable box remote. Change the TV from the cable box channel (3 or 4) to the modulator s channel. Q- Why does the modulator signal look snowy after I put in the bypass kit? A- The bypass kit will reduce the strength of the signal that passes through the filter and splitters. Try turning up the gain of the modulator or amplfying the signal at the head end of the distribution system to compensate for the loss. Make sure the modulator looks good without the bypass kit. Also make sure the kit is installed according to the diagram. Q- Can the bypass kit be used with digital cable service? A- Yes. When the kit is properly installed, the digital service has a clear path to the cable box; the signal does not pass through the filter. Even so, the filter only removes low VHF frequencies which are not near the typical digital range above channel 80. Q- Does this filter make clear channels for the modulator? A- No. Any splitters, amplifiers or filters that you use for combining signals together are separate from the ones used to bypass the cable box. If there are no clear cable channels then you will need an additional filter, such as NetMedia s NM-CNF7080, at the head of the distribution system. The filter goes on the cable service before it combines with the modulator. Modulator set from ch. 70-80. Cable Box Main cable or antenna Splitter/ Combiner NM-CNF7080 ch. 70-80 Notch Filter The notch filter does not bypass the cable box. NetMedia Cable Box Bypass/Combiner Kit NM-ACB3 The kit filter does not make clear channels for the modulator. Television NM-ACB3 Figure 1 - Bypassing a digital or analog cable box and recombining to a single coax input on the TV. The NM-ACB3 filter removes any conflict with the cable box on channel 3 or 4. The NM-CNF7080 filter removes any conflict with the cable service on channels 70-80. Switch the TV from the cable box channel (3 or 4) to the modulated channel (70-80). MAN-ACB3

RF Notch Filter NM-CNF7080 Removes Cable Channels 70-80 The NetMedia CNF7080 RF Notch Filter removes cable channels 70-80 (UHF 19-29) to allow insertion of up to 6 custom modulated sources (ch. 70, 72, 74, 76, 78, 80). This range is ideal for deletion because it has the fewest analog channels and does not typically interfere with digital services. The filter also prevents the modulated channels (70-80) from backfeeding through the cable system into neighbor s televisions. Product Includes: 1. NetMedia Notch Filter Male F-Connector Functions as input or output, provides easy connection to coax. Female F-Connector Functions as input or output, provides easy connection to splitter/combiner, amplifier, or distribution panel. Modulator Set for channels from 70 to 80 Splitter/ Combiner Distribution Panel or Splitter Camera Television FEATURES Main cable or antenna Makes room for 6 modulated channels Works with two NetMedia TriplePlays Keeps modulator signals from neighbors Bi-directional, passes DC power Deletes UHF and CABLE channels 1 year limited warranty CNF7080 Notch Filter Removes CABLE 70 to 80 and UHF 19-29 Figure 1 - Connecting the filter to an antenna or cable service for modulator distribution to multiple televisions. SPECIFICATIONS Filtered Frequencies: Filtered Channels: Filter Slope: Input/Output Connectors: Cable Type: Size: Weight: Television 498MHz to 564MHz CABLE 70-80, UHF 19-29 5 channels on either side 1 Male and 1 Female F, 75 Ohm Coax such as RG59 or RG6 0.8 dia. x 2.25 long 1.5 oz. (subject to change without notice) NM-CNF7080 MAN-CNF7080

One Year Limited Warranty NetMedia, Inc. warrants this product to be free from defects in materials and workmanship under normal use and service for One Year from the date of purchase or NetMedia will repair or, at its option, replace the defective product. Please keep your purchase receipt. In the unlikely event that you need warranty service, call NetMedia at 1-520-544-4567 for a Return Material Authorization (RMA) number. Then, return the product, with the RMA number clearly marked on the package, by a traceable method with freight pre-paid and accompanied by a copy of the purchase receipt to: Attn: Customer Service, NetMedia, Inc. 10940 N. Stallard Place, Tucson, AZ 85737-9527 No expressed or implied warranty is made for any defects in this product which result from accident, abuse, failure to operate the product in accordance with relevant instructions, neglect, immersion in or exposure to chemicals or liquid, extreme climate, excessive wear and tear and defect resulting from other extraneous causes such as unauthorized disassembly, repair and or modification. Any implied warranty arising from the sale of this product, including implied warranties of merchantability and fitness for a particular purpose, are limited to the warranty stated above. NetMedia shall not be responsible for any loss, damages or expenses, whether direct, consequential or incidental that arise from the use or inability to use this product. Some states do not allow limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights, which vary from state to state. Frequently Asked Questions Q- I connected the filter but why does the cable service look good until I combine it with the modulator? A- The filter should be applied to the antenna or cable service before the signals are combined at the beginning of the distribution system. Make sure you are not using any satellite diplexers to split or combine. If one of the signals still looks snowy then it probably needs amplification. Amplify it after the filter but before the signals are combined. +10 to +20dBmV is usually enough, too much will degrade the other signal. Q- Can this filter be used with digital cable service? A- Yes. The digital data usually starts in the 80 s which is above this filter s range. Expect to lose analog channels from around 68-82 but check all subscribed digital services including an Internet connection after it is installed. Q- Does this filter help modulator signals bypass and combine with cable box signals? A- No. Any splitters, amplifiers or filters (like this one) that you use for combining signals together are separate from the ones used to bypass the cable box. First, verify that the modulator and cable signals look good by connecting the coax directly to the TV with the TV s tuner. Then, to bypass a cable box, split the coax two ways with one side going to the cable box. If you use the cable box S-Video, composite, or component A/V outputs then the other side of the splitter goes directly to the TV. If you use the cable box coax output and there is only one coax input on the TV, then you must use a ch. 3/4 filter (included with NM-ACB3) and recombine the coaxes as shown in Figure 2. In any case, view the cable box through the appropriate TV connection, Video 1, ANT 2, channel 3/4, then change the TV (NOT THE CABLE BOX) to the modulated channels. You must repeat this process for every cable box. Modulator Cable Box Main cable or antenna Splitter/ Combiner NM-CNF7080 Ch. 70-80 Notch Filter The notch filter does not bypass the cable box. NetMedia Cable Box Bypass/Combiner Kit NM-ACB3 The kit filter does not make clear channels for the modulator. Television Figure 2 - Bypassing a digital or analog cable box and recombining to a single coax input on the TV. The NM-ACB3 filter removes any conflict with the cable box on channel 3 or 4. The NM-CNF7080 filter removes any conflict with the cable service on channels 70-80. Switch the TV from the cable box channel (3 or 4) to the modulated channels (70-80). NM-CNF7080 MAN-CNF7080