Optical Broadband Platform. NEW: Active and passive RFoG components

Optical Broadband Platform NEW: Active and passive RFoG components

Optical Broadband Platform Optical broadband platform for up to 16 modules Fitted with 2 redundant power supply and cooling fan units Wide selection of optical transmitters, amplifiers and return path receivers All optical and electrical connections are on the rear panel. Test sockets are on the front panel Can be integrated in any HMS-conform monitoring system Pluggable control panel with LC display, LEDs and input keys Tuning and management also via web browser RS 485 remote monitoring and control interface Several optical broadband platforms can be managed using just one controller module Automatic redundant operation of adjacent modules High reliability due to dust-proof modules and large cooling ribs Models available for mains voltage (100... 240 V AC ) and direct voltage (36... 72 V DC ) Design: 19 racking, 4 height units (RU) Kathrein's KOBRA system offers a comprehensive broadband platform meeting all the requirements of optical transmission. A wide range of optical transmitters, amplifiers and return path receivers is complemented by individual units in 19 design. The foundation is based on the 19 broadband platform KBP 4000R, into which a total of 16 modules can be inserted. It is already equipped with two redundant power supply and fan units ensuring reliable operation. The product package additionally includes a pluggable control panel with LC display, status LEDs and input keys. A power bus system in the rear section of the platform enables direct module connection to the 24 VDC supply voltage, to the RS 485 remote supervision and control interface as well as to control panel management. The broadband platform is designed as a 4 RU module carrier and can also be adapted to ETSI cabinets. 2

For use in hubs, for example, the remotely fed broadband platform 48 V DC variant (KBP 4048R) can also be used. Extensive management and monitoring facilities allow flexible and reliable operation in any net configuration. The provided pluggable control panel enables all required settings to be made on inserted devices. The net element controller module Ethernet (NCM 10) plays the leading role in this function. This unit establishes the connection between the control panel and all plugged-in modules via the RS 485 bus. The NCM 10 can thereby control up to three full KBP 4000R or 4048R broadband platforms. On the other hand, it converts the RS 485 data to SNMP/Ethernet and web browser/ Ethernet protocol. Thus, all settings and queries can be carried out via PC with a web browser. In addition, it is possible to integrate the broadband platform in any HMS-compatible monitoring system such as the KOM system from Kathrein. Together with the Kathrein optical compact receivers, the KOBRA can be used to set up an optical distribution system that meets each and every requirement. Modular design and a broad product programme make it possible to design anything cost-effectively, from simple optical feeds to classic HFC structures and video distribution in FTTH networks. Kathrein are continually enhancing their products and expanding their product range. Additional product variants are available upon request. 3

4 Functional and reliable - the "optical broadband The optical broadband platform KOBRA is designed with a sophisticated operation and management concept. The central element is the net element controller Ethernet 'NCM 10'. This module provides the interface to the rear RS 485 bus to which all platform modules are connected. In addition, it establishes the connection to external management systems, e.g. via web browser, or monitoring systems, such as HMS monitoring systems. Gerät 16 Ultimately, it enables local setting of all parameters through the control panel with display and input keys. Decentralized data storage in each individual module allows independent operation (without the controller module) after start-up. Slim modules, some with dual functions (e.g. return path receiver), ensure high functional density. Minimal space requirement increases cost-effectiveness and makes later upgrading easier. Despite their high output power, the optical amplifiers only require two or three slots. All test sockets are located on the front panel. This guarantees easy access for tests or measurements. The optical and RF interfaces are located on the rear panel of the platform, simplifying cabling in 19 racks.

platform " in detail Redundant power supply units, each equipped with double fan units, ensure high reliability. If service is required, the power supply units can even be exchanged under operational conditions (hot-pluggable). Ample cooling ribs guarantee long endurance of all active components. An additional advantage is the dust-proof design of all components. The cooling air only flows along the cooling ribs and not through the modules themselves. Disturbances due to dust and dirt are therefore practically ruled out. 5

19" broadband platform for optical modules KBP 4000R 25010022 KBP 4048R 25010021 Up to 16 modules can be inserted into the broadband platform Fitted with 2 redundant power supply and cooling fan units Power supplies can be exchanged under operation Plug-in controller with LC display, status LEDs and input keys Bus for: - 24 V DC module power supply - RS 485 remote monitoring and control interface - Controller management Models available for 100... 240 V AC and 48/60 V DC powering Automatic recognition of inserted modules Design: 19" racking, 4 height units (RU) Can be adapted to ETSI defined cabinets Note: The net element controller module Ethernet NCM 10 is required if modules are to be tuned to other settings and for monitoring purposes Type KBP 4000R KBP 4048R Order no. 25010022 25010021 Input voltage range V AC: 100-240 DC: 36-72 Input voltage W < 240 < 240 Max. input power of inserted modules W < 192 < 192 Dimensions (W x H x D) mm 483 x 102 x 476 483 x 102 x 476 Weight kg 12 12 6

Net element controller module Ethernet NCM 10 26210079 For management and monitoring of active modules in the 19" broadband platform KBP 40xx Conversion of RS 485 data to SNMP/ Ethernet and Web browser/ Ethernet protocol Interface to displays and input keys on the front panel Automatic recognition of all modules connected to the RS 485 bus Ethernet interface 10/100 Mbit/s for SNMPv1 and Web server Flash micro-controller technology for rapid and simple software updates via Ethernet interface LEDs for status display Low power consumption Note: Up to three KBP 40xxR broadband platforms can be managed and monitored by one NCM 10 module Block diagram LAN/WAN TCP/IP RJ 45 Cable Ethernet NCM 10 Kobra Broadband Platform #1 μp LC Display I/O RS 485 Module Input keys Module #2 Module Module #3 Module Module #16 Module RJ 45 Cable Kobra Broadband Platform #2 RS 485 #17 #18 #19 #32 Kobra Broadband Platform #3 RS 485 Module #33 Module #34 Module #35 Module #48 RJ 45 Cable Type NCM 10 Order no. 26210079 Power consumption W 2.5 7

Directly modulated broadcast transmitters, 1310 nm, extremely linear OTA 1303X2-E 24610353 OTA 1305X2-E 24610354 OTA 1308X2-E 24610355 OTA 1311X2-E 24610356 OTA 1313X2-E 24610357 OTA 1314X2-E 24610358 Opto-electrical conversion of forward path signals Extremely linear, low-noise laser with predistortion technology Optical output power between 3 and 14 dbm Adjustable optical output level, 0 to -3 db (relative) Active narrowcast input (NC) with high decoupling to the broadcast signal (BC) Electronic tuning elements for attenuation, slope, output level, Optical Modulation Index (OMI) etc. Automatic load control for constant OMI RS 485 interface Optical interfaces: E-2000, 0.1-dB-type (other connectors on request) Test socket for input signal Test socket for RF signal in front of the laser diode Block diagram 8

Type OTA 1303X2-E OTA 1305X2-E OTA 1308X2-E OTA 1311X2-E OTA 1313X2-E OTA 1314X2-E Order no. 24610353 24610354 24610355 24610356 24610357 24610358 Nominal output level optical dbm 3 5 8 11 13 14 Optical wave length nm 1310 Optical output level range (relative) db 0 to -3 Optical return loss db > 45 RF frequency range MHz 5-1000 Nominal input level (5 % OMI, Broadcast) Nominal input level (5 % OMI, Narrowcast) Level range (BC), in relation to nominal input level, electronically settable Slope range (BC), electronically settable Level range (NC), electronically settable Decoupling between BC and NC input dbμv 80 dbμv 87 dbμv 73 97 db -3... +16 dbμv 80 92 db > 50 CSO (CENELEC 42, 0 dbm at node) db 68 CTB (CENELEC 42) db 69 Return loss at 47 MHz db 20-1.5/oct., > 15 Return loss 5-65 MHz db > 18 Impedance Ω 75 Power consumption (operation) W 12 Power consumption (stand-by) W 4 Weight kg 1.3 9

Externally modulated transmitters OTA 1585X-E 24610361 OTA 1585D23X-E 24610362 OTA 1585X-E-SAT 24610363 Electro-optical conversion (externally modulated) of AM-VSB/QAM forward path signals Designed for operation with optical amplifiers (EDFAs/ YEDFAs) Excellent parameters enable design of optical distribution systems over 100 km in length Very low-noise, narrow-band DFB laser Optical modulator with 2 optical outputs Automatic RF gain control: CW carrier, video or manual Settable SBS threshold up to 19 dbm Wave lengths: 1550 nm or 1558.98 nm in ITU-DWDM channel plan (ITU channel 23) Tunable wave length up to ± 100 GHz Additional ITU wave lengths on request Optical interface: E-2000, 0.1 db-type (other connectors on request) Settable slope RF test output with 20 db tap loss OTA 1585X-E-SAT transmits the CATV frequency band (AM-VSB, FM, QAM) and the SAT-IF frequency band (analogue, DVB-S/ DVB-S2) Block diagram 10

Type OTA 1585X-E OTA 1585D23X-E OTA 1585X-E-SAT Order no. 24610361 24610362 24610363 Optical interface E-2000 E-2000 E-2000 Optical wave length nm 1550 + 10/- 2 ITU-T Ch 23 (1558.98 nm) 1550 + 10/- 2 Laser line width MHz 0.3 0.3 0.3 Optical output level dbm 2 x 8.5 2 x 8.5 2 x 8.5 Relative intensity noise (RIN) dbc/hz -160-160 -160 CATV Input level per TV channel, nominal dbμv 80 80 80 Input level range per TV channel (AGC) dbμv 78... 96 78... 96 78... 96 Return loss at 47 MHz db 20-1.5/oct., > 15 20-1.5/oct., > 15 20-1.5/oct., > 15 Frequency range MHz 47-1000 47-1000 47-862 Frequency response 47-862 MHz db < ± 0.75 < ± 0.75 < ± 0.75 Frequency response 862 MHz to 1 GHz db < ± 1.5 < ± 1.5 < ± 1.5 Adjustment range slope db -2... +8-2... +8-2... +8 CNR (CENELEC 42, without fibre, 0 dbm at node) db 55.5 55.5 54.5 (52.5) 1) CSO (CENELEC 42) dbc 65 65 64 CTB (CENELEC 42) dbc 65 65 63 Test socket db -20 ± 1-20 ± 1-20 ± 1 RF interface F-type socket F-type socket F-type socket SAT-IF Frequency range MHz - - 950... 2605 Frequency response 950-2605 MHz db - - < ± 2 Nominal input level per SAT-IF channel (OMI = 1 %) RMS input level range (ALC functional range) dbμv - - 85 db - - -11... +5 Impedance ohms - - 75 Test output at OMI = 1 % dbμv - - 66 ± 2.5 CNR (P rx = 0 dbm, 36 QPSK carrier, no fibre length) db - - > 27 Intermodulation spacing db - - < -35 General Power consumption W < 40 < 40 < 44 No. of required slots in KBP 40xxR 4 4 4 Weight kg 4.7 4.7 4.7 1) Value in brackets for CATV and SAT-IF application with 36 QPSK modulated SAT-IF signals with carrier frequencies in the range of 1000 2600 MHz 11

12 Directly modulated narrowcast downstream transmitters, DWDM OTN 3111L-E 24610397 OTN 3311L-E 24610213 OTN 3511L-E 24610398 OTN 3711L-E 24610399 Electro-optical conversion of forward path signals Extremely linear, low-noise DWDM laser with pre-distortion technology Wave lengths according to DWDM ITU grid, adjustable ± 100 GHz Optical output power: 11 dbm, cooled laser Two RF inputs (low/high) for adaptation to different level conditions Electronic tuning elements for attenuation, slope, output level, Optical Modulation Index, etc. Automatic load control for constant Optical Modulation Index RS 485 interface RF interfaces: F-type sockets Test socket for input level Test socket for optical output level or RF signal Block diagram BCin a BCin b μc Type OTN 3111L-E OTN 3311L-E OTN 3511L-E OTN 3711L-E Order no. 24610397 24610213 24610398 24610399 Optical interface E-2000 E-2000 E-2000 E-2000 Optical wave length nm 1552.520 1550.920 1549.320 1547.720 Nominal optical output level dbm 11 Optical output level range dbm 8-11 Optical return loss db > 45 RF frequency range MHz 5-1000 Input level for OMI = 5 % (low input) dbμv 73 97 Input level for OMI = 5 % (high input) dbμv 87 104 Attenuation range, electronically adjustable db 0-24 Slope range, electronically adjustable db -3... +16 Return loss at 47 MHz db 20-1.5/oct., > 15 Return loss 5-65 MHz db > 18 Test socket (output) db -20 Impedance ohms 75 Power consumption W 9

Directly modulated twin transmitters, CWDM OTD 06C11C12-E 24610393 OTD 06C13C14-E 24610394 OTD 06C15C16-E 24610395 OTD 06C17C18-E 24610396 Electro-optical conversion of forward path or return path signals Low-noise laser Optical output power: 2 x 6 dbm Twin transmitters with two independent RF paths and two independent laser diodes Electronic tuning elements for attenuation, Optical Modulation Index, etc. Automatic load control for constant Optical Modulation Index RS 485 interface for monitoring Optical interface: E-2000, 0.1 db-type RF interfaces: F-type sockets F-type test socket for input level Block diagram BCin1a BCin1b BCin2b BCin2a μc Type OTD 06C11C12-E OTD 06C13C14-E OTD 06C15C16-E OTD 06C17C18-E Order no. 24610393 24610394 24610395 24610396 Optical interface E-2000 Optical wave lengths nm 1471 and 1491 1511 and 1531 1551 and 1571 1591 and 1611 Nominal optical output level dbm 6 Optical output level tolerance db -1 +2 Optical return loss db > 45 RF frequency range MHz 5-1000 CNR with OMI = 3.9 %, P rx = 0 dbm, CENELEC db 51 CSO with OMI = 3.9 %, P rx = 0 dbm, CENELEC dbc 62 CTB with OMI = 3.9 %, P rx = 0 dbm, CENELEC dbc 63 Input level for OMI = 5 % dbμv 75 Attenuation range, electronically adjustable db 0-10 Transmitter decoupling 47... 862 MHz db 55 Return loss at 47 MHz db 18-1.5/oct., > 15 Return loss 5-65 MHz db > 18 Impedance Ω 75 Power consumption W 6 Test socket (output) db -20 Weight kg 1.3 13

Broadband amplifier, 5-1000 MHz TVO 1024 25110033 Broadband amplifier for universal use in forward and return paths For use in the optical broadband platform KOBRA Automatic load control (can be switched off) Frequency range: 5-1000 MHz Gain: 0... 24 db, electronically settable Slope range: 0... 16 db, electronically settable Main input for broadcast signals and secondary input for narrowcast signals Test socket for output signal Stand-by mode for low power consumption RS 485 interface Block diagram IN IN (coupled) ATT, EQ OUT TP μp RS485 CA1024 14 Type TVO 1024 Order no. 25110033 Frequency range MHz 5-1000 Gain, electronically settable db 0 to 24 Slope, electronically settable db 0 to 16 Frequency response (7-870 MHz) db ± 0.8 Frequency response (5-1000 MHz) db ± 1.5 Input level narrowcast input 1), relative db + 14 Max. output level 2), CSO > 60 db, CTB > 60 db dbμv 106 Return loss 5-65 MHz db > 18 Return loss 47-1000 MHz db 18-1/oct., > 15 Noise figure 5-870 MHz db 6.5 Noise figure 870-1000 MHz db 7.5 Impedance Ω 75 Power consumption, operation W 8 Power consumption, stand-by W 1 Weight kg 1.3 1) 14 db directional coupler 2) CENELEC raster, 42 channels, flat

Directly modulated broadcast transmitter, 1550 nm OTA 1508X-E 24610401 Opto-electrical conversion of forward path signals Low-noise laser with pre-distortion technology Optical output power: 8 dbm Electronic tuning elements for attenuation, optical modulation index, slope, output power, prechirp, etc. Automatic load control for constant Optical Modulation Index RS 485 interface for monitoring Optical interface: E-2000, 0.1 db-type RF interfaces: F-type sockets F-type test socket for input level SBS suppression and prechirp technology Block diagram Type OTA 1508X-E Order no. 24610401 Optical interface E-2000 Optical wave length nm 1550 Nominal optical output level dbm 8 Optical output level tolerance db ± 1.5 Optical return loss db > 45 RF frequency range MHz 5-1000 CNR with OMI = 4.1 %, P rx = 0 dbm, CENELEC 1) db 51 CSO with OMI = 4.1 %, P rx = 0 dbm, CENELEC 1) dbc 60 CTB with OMI = 4.1 %, P rx = 0 dbm, CENELEC 1) dbc 62 Input level for OMI = 5 % dbμv 73 97 Attenuation range, electronically adjustable db 0-24 Return loss at 47 MHz db 18-1.5/oct., > 15 Return loss 5-65 MHz db > 18 Impedance ohms 75 Power consumption W 9 Test socket (output) db -20 Weight kg 1.3 1) 20 km fibre, optical receiver with 0 dbm input power, lä=7pa/ Hz 15

Directly modulated broadcast twin transmitter, 1310 nm OTD 1304X-E 24610391 Opto-electrical conversion of forward path signals Low-noise laser with pre-distortion technology Optical output power: 2 x 4 dbm Twin transmitters with two independent RF paths and two independent laser diodes Electronic tuning elements for attenuation, Optical Modulation Index, etc. Automatic load control for constant Optical Modulation Index RS 485 interface for monitoring Optical interface: E-2000, 0.1 db-type RF interfaces: F-type sockets F-type test socket for input level BCin1a BCin1b μc BCin2b BCin2a Type OTD 1304X-E 16 Order no. 24610391 Optical interface E-2000 Optical wave length nm 1310 ± 20 Nominal optical output level dbm 4 each Tolerance of optical output level db -1 +2 Optical return loss db > 45 RF frequency range MHz 5-1000 CNR with OMI = 4.1 %, P rx = 0 dbm, CENELEC db 51 CSO with OMI = 4.1 %, P rx = 0 dbm, CENELEC dbc 62 CTB with OMI = 4.1 %, P rx = 0 dbm, CENELEC dbc 63 Input level for OMI = 5 % dbμv 75 Attenuation range, electronically adjustable db 0-10 Transmitter decoupling 47 862 MHz db 55 Return loss at 47 MHz db 18-1.5/oct., > 15 Return loss 5-65 MHz db > 18 Impedance Ω 75 Power consumption W 6 Test socket (output) db -20 Weight kg 1.3

Optical downstream receiver ORM 10 DS-E 24710045 Opto-electrical conversion of downstream signals Can be operated with one or two separate outputs Redundant operation possible Monitoring of the optical input power Monitoring of the RF output level Pilot-controlled RS 485 interface for monitoring and control Very low power consumption Optical interfaces: E-2000, 0.1 db-type; (other connectors on request) Ultra low-noise frontend Block diagram Similar to picture Opt. in BCout1 BCout2 Test RS485 μc Type ORM 10 DS-E Order no. 24710045 Optical interfaces E-2000 Optical wave length nm 1280-1610 Optical input level range dbm -8 to +4 Equivalent noise current density at -8 dbm pa/ Hz 5 Optical return loss db > 45 RF frequency range MHz 47 870 RF output level at OMI = 4 % (1 output) dbμv 94 RF output level at OMI = 4 % (2 outputs) dbμv 90.5 Frequency response db ± 1.0 Return loss at 85 MHz: - 1 db/oct. db > 19 Test sockets db 20 Impedance Ω 75 Power consumption, operation W < 12.5 Pilot frequency for AGC MHz 80.15 Weight kg 1.3 17

Optical return path receivers, twin ORM 40E 22E 24710018 24710026 ORM 22SC 24710046 Opto-electrical conversion of return path signals Two receivers, with individual shut-down Two separate outputs with test sockets Redundant operation possible Monitoring of the optical input power at all inputs Pilot-controlled Wide optical input powe range RS 485 interface Line code evaluation Stand-by mode for unused receiver to reduce power consumption Very low power consumption Optical interfaces: E-2000, 0.1-dB-type or SC/APC; (other connectors on request) Block diagram TP #1 ICS #1 IN #1 OUT #1 μp RS485 ICS #2 IN #2 OUT #2 OR265-nn TP #2 Type ORM 22E ORM 22SC Order no. 24710026 24710046 Optical interfaces E2000 SC/APC Optical wave length nm 1280-1610 Optical input level range dbm -16 to +2 Optical return loss db > 40 RF frequency range MHz 5-200 Equivalent noise current density pa/ Hz 2.5 RF output level at OMI = 5 % dbμv 90 Frequency response db ± 0.75 Return loss db > 19 Pilot control range db 36 Optical modulation index pilot % 5 Test sockets db 20 Impedance Ω 75 Power consumption, operation/stand-by W 6/1.5 Weight kg 1.3 18

Optical return path receiver, quad ORM 40E 24710018 Opto-electrical conversion of return path signals in HFC networks Four receivers, with individual shut-down Four separate outputs, each switchable to the test port Redundant operation possible Monitoring of the optical input power at all inputs AGC is both pilot-controlled and optical-power controlled Wide optical input power range RS 485 interface for monitoring and control Line code evaluation Stand-by mode for each unused receiver to reduce power consumption Very low power consumption Optical interfaces: E-2000, 0.1 db-type; (other connectors on request) Requires two slots in KOBRA KBP 40xx-R subrack Block diagram Block diagram LEDs LON P C PSK AGC Demod (opt. input power RS485 or pilot contr olled ) Optical input -22... +2dBm Optical input -22... +2dBm Optical input - 22... +2dBm 0...10dB 0...24dB 0...10dB 0...24dB 0...10dB 0...24dB 20 db test point RF output >85dBV 20 db test point RF output >85dBV RF output >85dBV 20 db test point Optical input RF output - 22... +2dBm 0...10dB 0...24dB >85dBV 20 db test point Type ORM 40E Order no. 24710018 Optical interfaces E-2000 Optical wave length nm 1280-1610 Sensitivity of the optical receiver A/W 0.8 Equivalent noise current density at -16 dbm pa/ Hz 2.5 Optical input level range dbm -16 to +2 Optical return loss db > 45 RF frequency range MHz 5-200 RF output level at OMI = 5 % dbμv 65 to 90 Frequency response db ± 0.75 Return loss at 47 MHz db > 20 RF output socket/ test socket (front panel) F Pilot control range db 26 Pilot tone frequency khz 590 640 Optical modulation index pilot % 5 Test sockets db 20 Impedance Ω 75 Power consumption normal operation (all 4 receivers active)/stand-by W 8/1.5 CINR with -11 dbm (4 QAM carriers with 2 MHz bandwidth, 10 % OMI) db 50 Number of slots required 2 Weight kg 2.25 19

RFoG return path receiver ORM 43E-RFoG 24710047 NEW Opto-electrical conversion of DOCSIS return path signals Two separate receivers, with individual shut-down Four separate outputs or one common output Redundant operation possible Monitoring of the optical input power at all inputs Wide optical input power range RS 485 interface Stand-by mode for unused receiver to reduce power consumption Very low power consumption Optical interfaces: E-2000, 0.1 db-type (other connectors on request) Ultra low-noise figure of 0.8 pa/ Hz Block diagram E1 ICS db A1 E2 ICS db A2 C E3 ICS db A3 E4 ICS db A4 μc Type ORM 43E-RFoG 20 Order no. 24710047 Optical interfaces E-2000 Optical wave length nm 1280-1630 Equivalent noise current density pa/ Hz 0.8 Optical input level range dbm -25 to -18 Optical return loss db > 40 RF frequency range MHz 5-85 RF output level at OMI = 17,5 % dbμv 76 Frequency response db ± 0.75 Return loss db > 19 Impedance Ω 75 Power consumption W 6 Weight kg 2.25

Optical amplifiers OBM 113S-E 24910028 OBM 213S-E 24910029 OBM 413D-E 24910030 OBM 116S-E 24910031 OBM 216D-E 24910032 OBM 416D-E 24910033 Amplifies optical signals in the 1550 nm range Optical output power: 13 or 16 dbm, 1 to 4 outputs, type dependent Monitors optical input and output levels as well as pump laser current 1 or 2 pump lasers, type dependent Automatic switch-off with low input level Low noise figure Stand-by mode for low power consumption Requires two slots in the optical broadband platform Optical interfaces: E-2000, 0.1 db-type (other connectors on request) Block diagram 1:n μc Type OBM 113S-E OBM 213S-E OBM 413D-E OBM 116S-E OBM 216D-E OBM 416D-E Order no. 24910028 24910029 24910030 24910031 24910032 24910033 Optical wave length nm 1540-1560 Optical interfaces E-2000 Optical return loss db 50 Optical input level dbm -4 +10 Noise figure (with 0 dbm) db < 4.8 Optical output power per output dbm 13 13 13 16 16 16 Optical output level tolerance (1551-1556/1548-1560 nm) db ± 0.5/0.8 Number of outputs 1 2 4 1 2 4 Number of pump lasers 1 1 2 1 2 2 Power consumption, operation W 12 12 24 12 24 24 Power consumption, stand-by W 6 6 10 6 10 10 No. of required slots in KBP 40xxR 2 Weight kg 2 21

Optical amplifiers (YEDFA) OBM 0420Y-E 24910043 OBM 0820Y-E 24910044 OBM 1620Y-E 24910045 OBM 1616Y-E 24910046 Amplifies optical signals in the 1550 nm range Optical output power: 16 or 20 dbm, 4, 8 or 16 outputs, type dependent Monitors optical input and output levels as well as pump laser current 2 pump lasers Automatic switch-off with low input level Low noise figure via cascading of an EDFA as preamplifier and a YEDFA as end stage Stand-by mode for low power consumption Requires two slots in the optical broadband platform KBP 40xxR Optical interfaces: - input: E-2000, 0.1 db-type (other connectors on request); - output: LC/APC Very high number of outputs due to high-gain, cladding-pumped YEDFA end stage LEDs for status display Block diagram EDFA μc YEDFA 1:n 22 Type OBM 0420Y-E OBM 0820Y-E OBM 1620Y-E OBM 1616Y-E Order no. 24910043 24910044 24910045 24910046 Optical wave length nm 1545-1565 Optical interfaces input/outputs E-2000 / LC/APC-8 Optical return loss db 40 Optical input level dbm -5 +10 Noise figure (at 0 dbm) db < 5.5 Optical output level per output dbm 20 16 Optical output level tolerance (1551-1556/1548-1560 nm) db ± 0.5 Number of outputs 4 8 16 16 Number of pump lasers 2 2 2 1 Power consumption, operation W 18 24 36 24 Power consumption, stand-by W 6 6 10 6 No. of required slots in KBP 40xxR 2 Weight kg 2

Optical fibre switch OFS 112-E 24810223 Redundancy selection from two input signals RS 485 management interface for integration in diverse NMS systems Independent level monitoring of both optical inputs Position-sensor and LED signalling for the active switch position Operation modes: Automatic, remote-controlled or manual LED display (red-yellow-green) for signalling the optical input level and the function of the module Block diagram E-2000 μc μp Optical fibre Type OFS 112-E Order no. 24810223 Optical wave lengths nm 1460-1620 Type of optical fibre Mono-mode 9/125 according to ITU G.625 Optical return loss db 45 Optical input level dbm -8... +12 Insertion loss (1540... 1570 nm) 1) db 1 Insertion loss (1460... 1620 nm) 1) db 1.7 Optical isolation of the input ports db 80 Number of outputs 1 Number of inputs 2 Power consumption, operation W 0.3 Temperature range (operation) C 0... 40 No. of required slots in KBP 40xxR 2 Optical interface E-2000 1) Without connectors 23

Externally modulated transmitters (19" design), 1550 nm ESA 1085XA-E 24610252 ESA 1085XA-E 24610140 ESA 1100XA-E 24610351 Designed for operation with optical amplifiers (EDFAs) Excellent parameters enable design of optical distribution systems over 100 km Very low-noise, narrow-band DFB laser Electro-optical modulator (Mach Zehnder) with 2 optical outputs Automatic RF gain control: CW carrier, video or manual Settable SBS threshold up to 19 dbm Service interface: HTTP/SNMP Ethernet (integrated Web server) Wave length: 1558.98 nm (ITU channel 23) Additional wave lengths and optical output levels on request Two power supply modules, pluggable during operation Design: 19" racking, 1 height unit, depth 600 mm Power supply, type dependent: 230 V AC or 48 V DC Block diagram 24 Type ESA 1085XA-E ESA 1085XA-E ESA 1100XA-E Order no. 24610252 24610140 24610351 Optical interfaces E-2000, 0.1 db E-2000, 0.1 db E-2000, 0.1 db Optical wave length nm 1558.98 1558.98 1558.98 Optical output level dbm 2 x 8.5 2 x 8.5 2 x 10.0 Relative intensity noise (RIN) dbc/hz -160-160 -160 Input level per TV channel, nominal dbμv 80 80 80 AGC dynamic range db +3... -6 +3... -6 +3... -6 Return loss at 47 MHz db 20-1.5/oct., > 15 20-1.5/oct., > 15 20-1.5/oct., > 15 Frequency range MHz 47-1000 47-1000 47-1000 Frequency response 47-862 MHz db ± 0.75 ± 0.75 ± 0.75 Test socket db -20 ± 1-20 ± 1-20 ± 1 RF interface F-type socket F-type socket F-type socket Voltage supply V 100... 240 AC ± 36... ± 72 DC ± 36... ± 72 DC Power consumption W 60 60 60 Weight kg 9.7 9.7 9.7

Directly modulated broadcast transmitters, 1310 nm OTS 1303N-E 24610334 OTS 1305N-E 24610340 OTS 1308N-E 24610405 OTS 1313N-SC 24610404 Opto-electrical conversion of forward signals such as AM-VSB, FM and QAM in HFC networks Low-noise laser with pre-distortion technology Optical output level adjustable from 0 to -3 db (relative) Dual RF input (low/high) to adapt to different input levels Electronic tuning elements for attenuation, slope, output level, Optical Modulation Index (OMI) etc. Automatic load control for constant OMI RS 485 interface Optical interface: E-2000, 0.1 db-type (other connectors on request) Test socket for input signal Test socket for RF signal of laser diode Stand-alone unit Block diagram Type OTS 1303N-E OTS 1305N-E OTS 1308N-E OTS 1313N-SC Order no. 24610334 24610340 24610405 24610404 Nominal output level optical dbm 3 5 8 13 Optical interfaces E-2000 E-2000 E-2000 SC/APC Optical wave length nm 1310 Optical output level range (relative) db 0 to -3 CNR 1) db 51 1) RF frequency range MHz 5-1000 Nominal input level (5% OMI, Low input) dbμv 73... 97 Nominal input level (5 % OMI, High input) dbμv 87... 104 Slope range, electronically adjustable db -2... +16 Return loss at 47 MHz db 20-1.5/oct., > 15 Return loss 5-65 MHz db > 18 Impedance Ω 75 Power consumption W 17 Mechanical dimensions, L x W x H (19, 1 RU) mm 483 x 240 x 45 EMC EN 50083-2 Safety EN 50083-1, EN 60950 Environmental conditions ETS 300 019-1-3 (temp. contr. loc.) Operational voltage V AC 100... 240 1) CENELEC 42, OMI = 4 %, 5 km mono-mode fibre, Prx = 0 dbm, Ith = 7 pa/ Hz 25

Externally modulated transmitter for CATV and SA ESA 1085XaS-E 230 V 24610392 Opto-electrical conversion of forward path signals Designed for operation with optical amplifiers (EDFAs) Excellent parameters enable design of optical distribution systems over 100 km Very low-noise, narrow-band DFB laser Optical modulator with 2 optical outputs Automatic RF gain control: CW carrier, video or manual Settable SBS threshold up to 19 dbm Service interface:: HTTP/SNMP Ethernet LCD display and LEDs on the front panel Additional wave lengths and optical output levels on request Optical interface: E-2000, 0.1 db-type (other connectors on request) Two power supply modules, pluggable during operation Design: 19" racking, 1 height unit, depth: 600 mm Power supply, type dependent: 230 V AC or 48 VDC Transmits the CATV frequency band (AM-VSB, FM, QAM) and the SAT-IF frequency band (analogue, DVB-S/ DVB-S2) Similar to picture Block diagram 26

T-IF (19" design) Type ESA 1085XaS-E 230V Order no. 24610392 Optical interface E-2000, 0.1 db Optical wave length nm 1548... 1560 Wave length tuning range GHz -100, -50, 0, 50, 100 Optical output level dbm 2 x 8.5 Relative intensity noise (RIN) dbc/hz -160 Input level per TV channel, nominal dbμv 80 AGC dynamic range db +3... -6 Return loss at 47 MHz db 20-1.5/oct., > 15 CATV Frequency range MHz 47... 862 Frequency response 47-862 MHz db ± 0.75 CNR (only CATV, without fibre length, CENELEC 42) db 54.5 CNR (CATV and SAT-IF, without fibre length, CENELEC 42 and 36 QPSK) db 52.5 CSO (P rx = 0 dbm, L = 25 km, EDFA) db 64 CTB (P rx = 0 dbm, L = 25 km, EDFA) db 63 Test socket db -20 ± 1 RF interface F-type socket SBS threshold (adjustable, CATV, fibre lengths < 65 km) dbm Up to 19 SAT-IF Frequency range MHz 950... 2605 Frequency response 950-2605 MHz db < ± 2 Nominal input level per SAT-IF channel (OMI = 1 %) dbμv 85 RMS input level range (ALC functional range) db -11... +5 Impedance ohms 75 Test output at OMI = 1 % dbμv 66 ± 2.5 CNR (P rx = 0 dbm, 36 QPSK carrier, no fibre length) db > 27 Intermodulation spacing db < -35 General Voltage supply V AC 2 x 100... 240 Power consumption W 68 Weight kg 9 Design 19" racking, 1 height unit, depth 600 mm 27

Optical amplifiers (19" design) OBV 1616 24910037 OBV 3216 24910036 OBV 820 24910035 OBV 1620 24910034 OBV 820W 24910053 Amplifies optical signals in the 1550 nm range Optical output power: 16.5 or 20 dbm, 8 to 32 outputs, type dependent Monitors optical input and output levels as well as pump laser current ErYb-doped optical amplifier Low noise figure LC display, LEDs and input keys on front panel RS 485 interface for management Ideal for FTTH or HFC applications Optical interfaces: LC/APC Design: 19" racking, 1 height unit (RU) Two power supply modules, pluggable during operation Block diagram EDFA μc YEDFA Similar to picture 1:n Type OBV 1616 OBV 3216 OBV 820 OBV 820W OBV 1620 Order no. 24910037 24910036 24910035 24910053 24910034 Optical wave length nm 1545-1565 Optical return loss db 45 Optical input level dbm -5 +10 Noise figure (with 0 dbm) db < 5.5 Optical output level per output dbm 16.5 16.5 20 20 20 Optical decoupling, input db 35 Optical decoupling, output db 35 Number of outputs W 16 32 8 8 16 Power consumption, max. W 45 45 40 40 45 Voltage supply V AC 100 240 Web interface No Yes No 28

29 Optical CWDM Mux/Demux BOD 04C-UL-K13 OD 24810166 BOD 04C-UL-K13 OM 24810228 Thin-film technology CWDM passband channel spacing: 20 nm according to ITU grid High isolation of optical channels Optical connectors: E-2000 Compact design Types:...-OM: Multiplexer...-OD: Demultiplexer Similar to picture Type BOD 04C-UL-K13 OD BOD 04C-UL-K13 OM Order no. 24810166 24810228 Number of channels 4 4 Central wave lengths nm 1511, 1531, 1551, 1571 1511, 1531, 1551, 1571 CWDM passband nm ± 6.5 ± 6.5 CWDM passband flatness db 0.5 0.5 Max. insertion loss 1) db 1.8 1.8 Typ. insertion loss 1) db 1.4 1.4 Maximum insertion loss Mux/Demux pair 1) db 2.4 2.4 Optical isolation betweeen adjacent channels db 30 30 Optical isolation (non-adjacent channel) db 45 45 Optical return loss db 45 45 Operating temperature range C 0... +65 0... +65 1) Without connectors

Optical 1310 CWDM Mux/Demux BOD 05C-1310-UL-K11 OM 24810088 BOD 05C-1310-UL-K11 OD 24810087 BOD 05C-1310-UL-K13 OM 24810075 BOD 05C-1310-UL-K13 OD 24810074 Thin-film technology CWDM passband channel spacing: 20 nm according to ITU grid High isolation of optical channels Extremely low insertion loss: UL- type Optical connectors: E-2000 Ultra-compact design, including pigtails Types:...-OM: Multiplexer...-OD: Demultiplexer Similar to picture Type BOD 05C-1310-UL- K11 OM BOD 05C-1310-UL- K11 OD BOD 05C-1310-UL- K13 OM BOD 05C-1310-UL- K13 OD Order no. 24810088 24810087 24810075 24810074 Number of channels 5 5 5 5 Central wave lengths nm 1471, 1491, 1511, 1531 1471, 1491, 1511, 1531 1511, 1531, 1551, 1571 1511, 1531, 1551, 1571 CWDM passband nm ± 6.5 ± 6.5 ± 6.5 ± 6.5 CWDM passband flatness db 0.5 0.5 0.5 0.5 Maximum CWDM insertion loss db 1.8 1.8 1.8 1.8 Maximum CWDM insertion loss 1) Mux/Demux pair db 2.4 2.4 2.4 2.4 Passband 1310 nm nm 1270-1350 1270-1350 1270-1350 1270-1350 Maximum insertion loss 1) 1310 nm db 1.0 1.0 1.0 1.0 Passband reflection band nm 1504-1578 1464-1618 1504-1578 1464-1618 Maximum insertion loss 1) reflection band db 0.6 0.6 0.6 0.6 Optical isolation betweeen adjacent channels db 30 30 30 30 Optical isolation (non-adjacent channel) db 45 45 45 45 Optical isolation 1310 nm - CWDM db 40 40 40 40 Optical return loss db 45 45 45 45 Operating temperature range C 0... +65 0... +65 0... +65 0... +65 1) Without connectors 30

Optical CWDM Mux/Demux BOD 08C-UL-K11-OM 24810230 BOD 08C-UL-K11-OD 24810229 Thin-film technology CWDM passband channel spacing: 20 nm according to ITU grid High isolation of optical channels Optical connectors: E-2000 Compact design Types:...-OM: Multiplexer...-OD: Demultiplexer Similar to picture Type BOD 08C-UL-K11-OM BOD 08C-UL-K11-OD Order no. 24810230 24810229 Number of channels 8 8 Central wave lengths nm 1471, 1491, 1511, 1531, 1551, 1571, 1591, 1611 1471, 1491, 1511, 1531, 1551, 1571, 1591, 1611 CWDM passband nm ± 6.5 ± 6.5 CWDM passband flatness db 0.5 0.5 Max. insertion loss 1) db 1.8 1.8 Typ. insertion loss 1) db 1.4 1.4 Maximum insertion loss Mux/Demux pair 1) db 2.4 2.4 Optical isolation betweeen adjacent channels db 30 30 Optical isolation (non-adjacent channel) db 45 45 Optical return loss db 45 45 Operating temperature range C 0... +65 0... +65 1) Without connectors 31

Optical 1310 CWDM Mux/Demux BOD 09C-1310-UL-K11-OM 24810079 BOD 09C-1310-UL-K11-OD 24810078 Thin-film technology CWDM passband channel spacing: 20 nm according to ITU grid High isolation of optical channels for the demultiplexer Extremely low insertion loss (UL) Optical connectors: E-2000 Ultra-compact design, including pigtails Compact design Types:...-OM: Multiplexer...-OD: Demultiplexer Similar to picture Type BOD 09C 1310-UL-K11-OM BOD 09C-1310-UL-K11-OD Order no. 24810079 24810078 Number of channels 9 9 Central wave lengths nm 1471, 1491, 1511, 1531, 1551, 1571, 1591, 1611 1471, 1491, 1511, 1531, 1551, 1571, 1591, 1611 CWDM passband nm ± 6.5 ± 6.5 CWDM passband flatness db 0.5 0.5 Maximum insertion loss 1) Mux/Demux pair db 3.2 3.2 Passband 1310 nm nm 1270-1350 1270-1350 Maximum insertion loss 1) 1310 nm db 1.0 1.0 Passband reflection band nm 1464-1618 1464-1618 Maximum insertion loss 1) reflection band db 0.6 0.6 Optical isolation betweeen adjacent channels db 30 30 Optical isolation (non-adjacent channel) db 15 45 Optical isolation 1310 nm CWDM db 40 40 Optical return loss db 45 45 Operating temperature range C 0... +65 0... +65 1) Without connectors 32

Optical DWDM Mux/Demux 200-GHz ITU grid BOD 0420 K31-OD 24810112 BOD 0420 K31-OM 24810113 Thin-film technology DWDM channel spacing: 200 GHz according to ITU grid High isolation of optical channels Optical connectors: E-2000 Ultra-compact design Types:...-OM: Multiplexer...-OD: Demultiplexer Similar to picture Type BOD 0420 K31-OD BOD 0420 K31-OM Order no. 24810112 24810113 Number of channels 4 Central wave lengths nm 1552,52; 1550,92; 1549,32; 1547,72 (C31, C33, C35, C37) DWDM passband nm ± 0.25 CWDM passband flatness db 0.5 Maximum insertion loss 1) db 2.0 Typ. insertion loss 1) nm 1.6 Optical isolation betweeen adjacent channels db 30 Optical isolation (non-adjacent channel) db 45 Optical return loss db 45 Operating temperature range C 0 to +65 1) Without connectors 33

Optical splitters BOV 002-CWDM 24810162 BOV 003-CWDM 24810184 BOV 004-CWDM 24810160 Optical splitters for universal application Low insertion loss Optimised for 1310 and 1550 nm or CWDM wave lengths Optical connectors: E-2000 (other connectors on request) High reliability Ultra-compact design, including pigtails Similar to picture Type BOV 002-CWDM BOV 003-CWDM BOV 004-CWDM Order no. 24810162 24810184 24810160 Optical wave length nm 1310, 1468.5-1617.5 Splitting ratio 1:2 1:3 1:4 Typ. insertion loss 1) db 3.3 5.6 7.4 Maximum insertion loss 1) db 3.6 5.9 7.7 Uniformity db 0.7 1.1 1.4 Optical isolation, outputs db 50 Min. return loss db 45 1) Without connectors 34

Optical taps BOC 003-CWDM 24810231 BOC 004-CWDM 24810232 BOC 005-CWDM 24810233 BOC 006-CWDM 24810234 BOC 007-CWDM 24810235 BOC 008-CWDM 24810236 BOC 009-CWDM 24810237 BOC 010-CWDM 24810238 BOC 012-CWDM 24810239 BOC 014-CWDM 24810240 Optical splitters for universal application Low insertion loss Optimised for the CWDM spectrum of 1471 1611nm (C11 C18) Optical connectors: E-2000 (other connectors on request) High reliability Ultra-compact design, including pigtails Similar to picture Type BOC 003- CWDM BOC 004- CWDM BOC 005- CWDM BOC 006- CWDM BOC 007- CWDM BOC 008- CWDM BOC 009- CWDM BOC 010- CWDM BOC 012- CWDM BOC 014- CWDM Order no. 24810231 24810232 24810233 24810234 24810235 24810236 24810237 24810238 24810239 24810240 Optical nm 1471 1611 wave length Typ. tap loss 1) db 3.2 4 5 6 7 8 9 10 12 14 Tap loss tolerance db ± 0.4 ± 0.4 ± 0.4 ± 0.4 ± 0.4 ± 0.8 ± 0.9 ± 0.9 ± 1.3 ± 1.5 Typ. through loss 1) db 3.2 2.6 1.9 1.5 1.2 0.9 0.8 0.6 0.5 0.4 Through loss tolerance Optical isolation, outputs Temperature range (operation) db ± 0.4 ± 0.3 db 50 C -10 +65 1) Without connectors 35

Optical Mux/Demux, tube design BWMR 1550-1610-60-LC-RFoG 24810255 BWMR 1310-1610-60-LC-RFoG 24810256 BWMR 1550-1310-60-LC-RFoG 24810257 NEW Optical multiplexer/demultiplexer: Wave lengths in DS: 1310 or 1550 nm; Wave lengths in US: 1310 or 1610 nm High reliability Extremely high isolation of 65 db Low insertion loss Design: tube Optical connectors: 900 μm fibres Connectors: LC/APC Designed for operation in RFoG networks for separation of downstream and upstream wave lengths in the headend Similar to picture 36 Type 1) Without connectors BWMR 1550-1610-60-LC-RFoG BWMR 1310-1610-60-LC-RFoG BWMR 1550-1310-60-LC-RFoG Order no. 24810255 24810256 24810257 Wave length 1 'pass channel' 1550 ± 40 1310 ± 40 1550 ± 40 Wave length 2 'reflect channel' nm 1610 ± 6.5 1610 ± 6.5 1310 ± 20 Loss tolerance 'pass channel common' with wave length 1 1) db 1.0 Selection 'common pass channel' with wave length 2 db 45 Loss tolerance 'common reflect channel' with wave length 2 1) 0.5 Selection 'common pass channel' with wave length 1 db 15 Directional attenuation 'pass channel reflect channel' with wave length 1 60 PDL db 0.2 Optical return loss db 45 Max. optical output mw 300 Dimensions (L x D) mm 39 x 5.5 Operating temperature C -5... +70 Storage temperature C -40... +85 Fibre Optical connectors SMF, 0.9 mm loose tube, l = 1 m LC/APC

Optical passive racking 19", 1 RU KOP 10 25010023 19" racking for passive optical components Universal application KOP 10 can be equipped with up to 24 OKU 01/SC, OKU 01/E or OKU 01/SC-E optical connectors Unused openings can be covered with protective caps Ideal for integration of the BOV 00x optical splitters or BOC 0xx taps Dimensions (H x W x D) in mm: 45 x 440 x 215 Accessories (included in delivery scope): 19 fastening kit, hook-and-loop tape (2 units, 200 x 5 mm), 24 dummy plugs 37

FTTX RFoG splitters 19", 1 RU BOS 2032SC 25010067 BOS 2032LC 25010066 NEW 19" 1 RU carrier Contains an optical 2:32 splitter Two group inputs and 32 outputs with SC/APC or LC/APC connectors ITU-G.694.2-compliant Broadband PLC splitter Integrated fibre tray Block diagram Similar to picture Type BOS 2032SC BOS 2032LC Order no. 25010067 25010066 Configuration 1 x 2:32 Wave length range nm 1260 1650 Max. insertion loss (-40 +80 C) per splitter 1) db 17.8 Uniformity db < 1.6 Polarisation dependent loss db 0.35 Typ. isolation (directivity) db 55 Min. return loss db 55 Temperature range (operation/storage) C -40... +85 Relative humidity (non-condensing) % 90 Max. optical output mw < 300 Dimensions (W x H x D), 19" chassis mm 482 x 45 x 196 Fibre type (Core/sheathing/outer diameter) μm 9/125/250; G657A Type of optical connection SC/APC LC/APC 1) Includes opt. connectors, over complete temperature range and all polarisation states 38

FTTX RFoG splitters 19", 1 RU BOS 2064SC 25010065 BOS 2064LC 25010064 NEW 19" 1 RU carrier Contains an optical 2:64 splitter Two group inputs and 64 outputs with SC/APC or LC/APC connectors ITU-G.694.2-compliant Broadband PLC splitter Integrated fibre tray Block diagram Similar to picture Type BOS 2064SC BOS 2064LC Order no. 25010065 25010064 Configuration 1 x 2:64 Wave length range nm 1260 1650 Max. insertion loss (-40 +80 C) per splitter 1) db 21.1 Uniformity db < 1.2 Polarisation dependent loss db 0.3 Typ. isolation (directivity) db 55 Min. return loss db 55 Temperature range (operation/storage) C -40... +85 Relative humidity (non-condensing) % 90 Max. optical output mw < 300 Dimensions (W x H x D), 19" chassis mm 482 x 45 x 196 Fibre type (Core/sheathing/outer diameter) μm 9/125/250 Type of optical connection SC/APC LC/APC 1) Including opt. connectors 39

Optical attenuators ODF 01/SC 24810198 ODF 02/SC 24810199 ODF 03/SC 24810200 ODF 04/SC 24810201 ODF 05/SC 24810202 ODF 06/SC 24810203 ODF 07/SC 24810204 ODF 08/SC 24810205 ODF 09/SC 24810206 ODF 10/SC 24810207 Optical SC attenuators for universal use with SC connectors Available types: ODF 01/SC... ODF 10/SC for attenuation values of 1 db... 10 db in 1 db steps Type ODF 01/SC ODF 02/SC ODF 03/SC ODF 04/SC ODF 05/SC Order no. 24810198 24810199 24810200 24810201 24810202 Attenuation db 1 2 3 4 5 Type ODF 06/SC ODF 07/SC ODF 08/SC ODF 09/SC ODF 10/SC Order no. 24810203 24810204 24810205 24810206 24810207 Attenuation db 6 7 8 9 10 40

41 Optical attenuators ODF 01/E 24810141 ODF 02/E 24810141 ODF 03/E 24810143 ODF 04/E 24810144 ODF 05/E 24810145 ODF 06/E 24810146 ODF 07/E 24810147 ODF 08/E 24810148 ODF 09/E 24810149 ODF 10/E 24810150 Optical E-2000 attenuators for universal use with E-2000 connectors Available types: ODF 01/E... ODF 10/E for attenuation values of 1 db... 10 db in 1 db steps Type ODF 01/E ODF 02/E ODF 03/E ODF 04/E ODF 05/E ODF 06/E ODF 07/E ODF 08/E ODF 09/E ODF 10/E Order no. 24810141 24810142 24810143 24810144 24810145 24810146 24810147 24810148 24810149 24810150 Attenuation db 1 2 3 4 5 6 7 8 9 10

Optical patch cables OFC 050/E yellow 24810152 OFC 150/E yellow 24810154 OFC 300/E yellow 24810157 OFC 050/E red 24810151 OFC 150/E red 24810155 OFC 300/E red 24810156 OFC 300/SC 24810104 OFC 300/LC 24810126 OFC 300/LC-E 24810174 OFC 300 SC-E 24810262 Optical patch cables for universal application 2.5 mm patch cord Type OFC 050/E yellow OFC 150/E yellow OFC 300/E yellow OFC 050/E red OFC 150/E red Order no. 24818152 24818154 24818157 24810151 24810155 Length cm 50 150 300 50 150 Diameter of patch cord mm 2.5 2.5 2.5 2.5 2.5 Opt. attenuation of optical connectors db 0.1 0.1 0.1 0.1 0.1 Optical connectors 2 x E-2000 Type OFC 300/E red OFC 300/SC OFC 300/LC OFC 300/LC-E OFC 300 SC-E Order no. 24810156 24810104 24810126 24810174 24810262 Length cm 300 300 300 300 300 Diameter of patch cord mm 2.5 2.5 2.5 2.5 2.5 Opt. attenuation of optical connectors db 0.1 0.3 0.3 0.3 0.3/0.1 Optical connectors 2 x E-2000 2 x SC/APC 2 x LC/APC LC/APC E-2000 SC/APC E-2000 42

Optical couplers OKU 01/SC 24810031 OKU 01/SC-E 24810099 OKU 01/E 24810100 Optical couplers for universal use Available types: - OKU 01/SC: SC/APC both ends - OKU 01/SC-E: Optical connection adapter SC/APC to E-2000 - OKU 01/E: E-2000 both ends Similar to picture 43

Please contact us for advice: The products described must only be installed by qualified specialists. Please consult the provided instruction manuals for the safety instructions that are to be considered during use. 99811676/1/0411/JH/Pf Technical modifications are reserved. All specified data are typical values if not otherwise noted. www.kathrein.de catv@kathrein.de KATHREIN-Werke KG Phone +49 (0)8031 184-0 Fax +49 (0)8031 184-385 Anton-Kathrein-Str. 1-3 P.O. Box 10 04 44 83004 Rosenheim GERMANY