Safety information Roxtec recommends that all installations are performed without facility operation. Follow national regulations and installation codes. ny action affecting the routed service should be performed according to manufacturer recommendations. Installation instructions Roxtec CF 6 EMC and Roxtec CF 6 O EMC CF 6 EMC CF 6 O EMC Openable frame perture dimensions and conductive area Measurements in (mm). 0 9. 7 Ø. (x) Ø7 (x) 0. 8. 87 0. T Maximum wall thickness is T: mm. : This area shall always be conductive and connected to ground. Tools needed Phillips screwdriver (not included) Torx key (included) Cable stripper tool. Recommended by the cable manufacturer (not included)
Components CF frame 6 7. Back plate. EMC plate. Cross recess screws. Torx screws. Cabinet/wall 6. Compression rubber 7. Front plate Roxtec Lubricant Roxtec CM ES module Roxtec CM PE module B B C C D B D B F G E F E E F : Environmental side B: Interior side C: Cable jacket D: Cable screen E: Plastic film F: Conductive tape G: Vertical ES screen : Environmental side B: Interior side C: Cable jacket D: Cable screen E: Plastic film F: Conductive tape Roxtec CM ES modules For cable/pipe outer diameter Module size Minimum Maximum CM w0/0 ES 0 0 CM 0w0/0 ES 0 0 CM w0 ES. 0. CM 0w0 ES. 6. CM 0w0 ES 0 CM 0 0- ES 9.. Roxtec CM PE modules For cable/pipe outer diameter Module size Minimum Maximum CM w0/0 PE 0 0 CM 0w0/0 PE 0 0 CM w0 PE. 0. CM 0w0 PE. 6. CM 0w0 PE 0 CM 0 0- PE 9.. Unused modules can be used as spare capacity. Center cores must always be present in unused modules.
Installation a b Clean the area in order to achieve good electrical conductivity between the counter frame and the inside of the structure. Route the cable through the compression rubber and front plate. Install the back plate and the EMC plate inside the cabinet. For openable frames, install the back plate and the EMC plate around the cables inside the cabinet. Mark where the outer jacket is to be removed to fit the conductive tape position (min mm). Cut and remove the outer jacket and any plastic foil to expose the screen/armor of the cable. Terminate the screen/armor according to the cable requirement. Suggestions for cable preparations are available on www.roxtec.com. Correct placement of cable in EMC module.
Installation of Roxtec CM ES modules Remove the protection paper from the modules and fold back the tape. Note: Protection paper must be removed on spares also. dapt layers to outer jacket. dapt layers to cable screen. dapt vertical ES screen to cable screen. 6 7 8 chieve a gap of 0.-.0 mm () between the module halves. If not, repeat step -. The halves may not differ by more than one layer. Ensure good electrical conductivity between the cable screen and module tape. Fold the adhesive conductive tape tightly inside the module half from one side along the inner layers. Lift the plastic film from the folded side. Fold the tape on the other side tightly inside the module half. There must be no air-pockets. 9 0 Fold the plastic film back inside the module half. Lubricate all modules sparsely with Roxtec Lubricant on inside and outside rubber surfaces only. Do not lubricate the plastic film. For spare modules, lubricate all inside sealing surfaces with Roxtec Lubricant. Do not lubricate the film. Remove the plastic film. Keep the tape clean. Note: Plastic film must be removed on spares also.
6 Insert the modules from the outside of the cabinet with the conductive tape inwards. Cable shall be installed so that eventual extra exposed cable screen runs into the cabinet. For openable frames, fit the compression gasket around the cables by using the pre-opened long side. Thoroughly lubricate the compression rubber on both outside and inside surfaces with Roxtec Lubricant. 7 8 9 Position the compression rubber around the modules. Position the front plate on the compression rubber. Tighten the torx screws alternately in small steps. lways start with the short sides. Recommended torque 8-0 Nm. Disassembly and reinstallation of Roxtec CM ES modules Untighten the torx screws alternately. lways start with the short sides. Remove the front plate. Remove the compression rubber. Push out the modules needed from the back side. Clean the void. dapt the removed module to the new cable according to the CM ES instructions.
Installation of Roxtec CM PE modules Remove the protection paper from the modules and fold back the tape. dapt layers to outer jacket. dapt layers to cable screen. chieve a gap of 0.-.0 mm () between the module halves. If not, repeat step -. The halves may not differ by more than one layer. Ensure good electrical conductivity between the cable screen and module tape. 6 7 8 Fold the adhesive tape tightly inside the module half from one side along the inner layers. Lift the plastic film from the folded side. Fold the tape on the other side tightly inside the module half. There must be no air-pockets. Fold the plastic film back inside the module half. 9 0 Lubricate all modules sparsely with Roxtec Lubricant on inside and outside rubber surfaces only. Do not lubricate the film. For spare modules, lubricate all inside sealing surfaces with Roxtec Lubricant. Do not lubricate the film. Remove the plastic film. Keep the tape clean. Note: Plastic must be removed on spares also. Insert the modules from the outside of the cabinet. 6 Cable shall be installed so that eventual extra exposed cable screen runs into the cabinet. For openable frames, fit the compression gasket around the cables by using the pre-opened long side. Thoroughly lubricate the compression rubber on both outside and inside surfaces with Roxtec Lubricant. Position the compression rubber around the modules.
7 8 Position the front plate on the compression rubber. Tighten the torx screws alternately in small steps. lways start with the short sides. Recommended torque 8-0 Nm. Disassembly and reinstallation of Roxtec CM PE modules Untighten the torx screws alternately. lways start with the short sides. Remove the front plate. Remove the compression rubber. Push out the modules needed from the back side. Clean the void. dapt the removed module to the new cable according to the CM PE instructions.
Note For optimum reliability, wait hours or longer after installation before exposing the cables/pipes to strain or pressure. n incorrectly adapted module shall be replaced (layers shall not be reused). Cables shall go straight through the frame. Permitted Roxtec modules: CM ES and CM PE. Minimum diameter of cables:. mm. Maximum diameter of cables:. mm. pprovals or certificates may include amendments or limitations related to this application. The latest version of this and related documents are found at roxtec.com. DISCLIMER The Roxtec cable entry sealing system ( the Roxtec system ) is a modularbased system of sealing products consisting of different components. Each and every one of the components is necessary for the best performance of the Roxtec system. The Roxtec system has been certified to resist a number of different hazards. ny such certification, and the ability of the Roxtec system to resist such hazards, is dependent on all components that are installed as a part of the Roxtec system. Thus, the certification is not valid and does not apply unless all components installed as part of the Roxtec system are manufactured by or under license from Roxtec ( authorized manufacturer ). Roxtec gives no performance guarantee with respect to the Roxtec system, unless (I) all components installed as part of the Roxtec system are manufactured by an authorized manufacturer and (II) the purchaser is in compliance with (a), and (b), below. (a) During storage, the Roxtec system or part thereof, shall be kept indoors in its original packaging at room temperature. (b) Installation shall be carried out in accordance with Roxtec installation instructions in effect from time to time. The product information provided by Roxtec does not release the purchaser of the Roxtec system, or part thereof, from the obligation to independently determine the suitability of the products for the intended process, installation and/or use. Roxtec gives no guarantee for the Roxtec system or any part thereof and assumes no liability for any loss or damage whatsoever, whether direct, indirect, consequential, loss of profit or otherwise, occurred or caused by the Roxtec systems or installations containing components not manufactured by an authorized manufacturer and/or occurred or caused by the use of the Roxtec system in a manner or for an application other than for which the Roxtec system was designed or intended. Roxtec expressly excludes any implied warranties of merchantability and fitness for a particular purpose and all other express or implied representations and warranties provided by statute or common law. User determines suitability of the Roxtec system for intended use and assumes all risk and liability in connection therewith. In no event shall Roxtec be liable for indirect, consequential, punitive, special, exemplary or incidental damages or losses. Roxtec International B Box 0, 7 Karlskrona, SWEDEN PHONE +6 6 67 00, FX +6 80 EMIL info@roxtec.com, www.roxtec.com rticle number: SS000080 Document number: SS000080 version D Roxtec and Multidiameter are registered trademarks of Roxtec in Sweden and/or other countries.