SHARE 30 TX 0 90 60 RX COM +5V LISTED 7TT US APARATUS TeamWork Kits Installation Guide TeamWork 400 and TeamWork 600 Kits The TeamWork 400 and TeamWork 600 kits consist of an HDMI switcher, system controller, Cable Cubby, and cables packaged together as a complete system that, in most cases, requires no configuration. Contact Closure & Tally 00-20V 50/60Hz IPL T PC System Controller 2A MAX 2A MAX IR IN S G AUDIO/VIDEO LAN Flat Panel AC Cord 2V 0.3A MAX SW4 HDMI Switcher +V G SW4 HDMI S TALLYOUT CONTACT RS-232 Control Cable HDMI Pro Cable HDMI Video Regional Sales 50 SOUTH 20 WEST EAST NORTH 90 60 30 0 Flat Panel Display w/ Integrated Speakers Regional Sales 50 SOUTH 20 WEST EAST NORTH Cable Cubby 2000 Cable Access Enclosure Show Me Cables The diagram above shows a typical TeamWork 400 application. The input devices (laptops and a tablet) connect to the switcher, using Show Me cables. The Show Me cables allow the user to select the active input on the switcher. A control cable connects the RS-232 ports on the switcher and the system controller. The system controller powers the display on and off. The system controller has been configured so that when a video signal is detected on any of the switcher inputs, the display is powered on. A 30 second timer is started when no signal is detected on any of the switcher inputs. If an active source is detected before the timer expires, the display remains on and the timer is reset. If 30 seconds pass without an active signal, the system controller powers off the display. The TeamWork kits work, as described, without further software configuration. If you need to change the behavior or operation of the system, you must configure the system controller (see the IPL T PC/IPL T PCi User Guide at www.extron.com). TeamWork VGA Kit The TeamWork VGA kit adds support for legacy analog computer sources to the TeamWork 400 and TeamWork 600 collaboration systems. For fast installation, the analog-to-digital converter (RGB-HDMI 300 A) is pre-configured for use with flat panel displays that have a resolution of 080p. If you need to change the behavior or operation of the converter, see the RGB-DVI 300 and RGB HDMI 300 (A) User Guide at www.extron.com. NOTE: The RGB-HDMI 300 A is pre-configured to lock out the front panel buttons. To enable or disable front panel security lockout, press and hold the Menu and Enter buttons simultaneously for two seconds.
HDMI Switcher Analog-to-Digital Converter SW4 HDMI S TALLYOUT 2V.0A MAX RS-232 2V 0.3A MAX +V CONTACT RGB/R-Y,Y,B-Y AUDIO RGB - HDMI 300 A HDMI Contact Closure and Tally G VGA Show Me Cable SHARE Features z Standard systems support groups of up to four (TeamWork 400) or six (TeamWork 600) users. z Standard systems contain a complete turnkey package that includes cables, switcher, system controller, and Cable Cubby enclosure. z System controller pre-loaded with Global Configurator that requires no further adjustment. z Works with most commercially available flat panel displays, laptops and tablets. z HDCP compliant z Supports legacy analog sources with optional TeamWork VGA kit. z Section 508 compliant. Kit Components When your kit is delivered, check that all the components are present. TeamWork 400 and TeamWork 600 Kits TeamWork 400 TeamWork 600 HDMI switcher (SW4 HDMI, 4 input) (SW6 HDMI, 6 input) System controller (IPL T PC) (IPL T PC) Cable Cubby Cable Cubby 200 Cable Cubby 400 Power modules (included with the Cable Cubby) 2 HDMI Show Me cables 4 6 HDMI cable Switcher control cable 4-cable Cable Cubby Bracket Kit pair Installation Guide TeamWork Kits Installation Guide TeamWork VGA Kit TeamWork VGA Analog-to-digital converter (RGB-HDMI 300 A) VGA Show Me cable HDMI cable Installation Guide TeamWork Kits Installation Guide 2
00-20VAC 50/60Hz 2A MAX 2A MAX COM +5V IR IN S G LAN US LISTED 7TT AUDIO/VIDEO APARATUS TeamWork Kits Installation Guide (Continued) Display Requirements The TeamWork system is designed to work with most brands and models of flat panel displays available worldwide. For optimum performance, consider the following when selecting the displays for your TeamWork installation. The display should be tested thoroughly prior to installation or mass deployment of TeamWork systems. Power attributes The system works by controlling AC power to the display. When the display is in the ON state with an HDMI input selected, it must be able to power back ON to the same HDMI input when AC power is disconnected and reconnected. If the display doesn t behave this way, an alternate display should be used. Alternatively, you may need to control the display a different way (i.e. RS-232, infrared, or via Ethernet) using a different type of control processor. Sleep mode if the display has a Sleep Mode feature (sometimes called auto sleep ), it must be disabled. Many displays have an option to disable this within the menu settings. Resolution The TeamWork systems were designed for use with flat panels having an HDMI input connector and having a native resolution of 080p. Many of the readily available consumer and professional displays support 080p natively. Audio Audio from source devices is supported in the TeamWork system by routing it as an embedded audio signal to the display for playback via integrated speakers. Most displays with HDMI inputs and integrated speakers work this way. Some professional or commercial grade displays do not have integrated speakers and will not support audio playback. Typically, source devices with HDMI output connectors embed audio onto the HDMI connector. NOTES: Always check and test compatibility before installation. Some systems may require advanced configuration of the system controller and require the display to be controlled by RS-232, Ethernet, or Infrared. Some displays support a lockout of local buttons. recommends that, after setup, user accessible controls are locked whenever possible. This ensures the display remains optimized for the TeamWork system. System Controller HDMI Switcher 2V 0.3A MAX S TALLYOUT +V CONTACT G Teamwork Systems work by controlling AC power to the display. RS-232 Switcher Control TeamWork systems require a display that returns to the previous state when the power cord is disconnected and then plugged back in. How to check if a display is compatible:. Apply AC power to the display. 2. Turn the display ON. 3. Select the HDMI input. 4. Adjust the volume. 5. Unplug the display (remove AC power). 6. Re-apply AC power to the display. If the display powers back up (to the ON state) and to the same input and volume level, the display will work with the TeamWork system. AC Power For Audio Playback display should have integrated speakers. Display should have an HDMI input and support embedded audio. 080p Native Resolution Display 3
Installation Install the Module Assemblies and Show Me Cables Detailed instructions are in the Cable Cubby Setup Guide. recommends the layout shown to the right with AAP shelf assemblies on either side of the power modules. NOTE: The figure to the right shows the US power module. Power modules for other countries look different. Cable Pass-through Cassette Module Power Module (to source device) (to switcher) Top of Cable Cubby Share Button Three-conductor pigtail for contact closure and tally Bottom of Cable Cubby ATTENTION: The end with the button and LED connects to the input devices and must come out of the top of the Cable Cubby. Le bout avec le bouton et la LED se connecte aux appareils d entrée et doit ressortir du haut du Cable Cubby. The end with the three-conductor pigtail connects to the switcher and must come out of the bottom of the Cable Cubby. Le bout avec le mini câble à trois conducteurs se connecte au sélecteur et doit ressortir du bas du Cable Cubby.. Assemble the cable pass-through cassette module as shown in the diagram to the right. 2. Insert the cable cassette module into the Cable Cubby from underneath and secure them in position with the provided #4 40 Phillips head screws and star washers. NOTE: The diagrams on this page show HDMI Show Me cables in the cable cassette module. If you are using the TeamWork VGA kit, install VGA Show Me cables in exactly the same way. 3 Snap the included hole plugs into any unused holes. 2 Secure the grommet panel on the cassette module. Insert cables through the bottom of the cassette module and into the holes of the grommet panel. Install the Power Modules in the Cable Cubby Insert the power module into the Cable Cubby from underneath and secure the power modules in position with the provided #4 40 Phillips head screws and star washers. WARNING: Possible electric shock: To ensure good electric grounding, you must use the star washers with the screws. AVERTISSEMENT: Risque de choc électrique: Afin d assurer une mise à la terre correcte, vous devez fixer les modules d alimentation au Cable Cubby à l aide de vis et de rondelles en étoile. 25V~ 2A MAX TOTAL 2 Secure the modules using two of the provided screws. Slide the cassette modules into the Cable Cubby from underneath. 4
AUTO IR SWITCH CONFIG CONFIG S IPL T PC MENU R ENTER S SIGNAL HDCP TX RX ADJUST IR HDMI SWITCHER RGB - HDMI 300 A 00 LINK ACT TeamWork Kits Installation Guide (Continued) Mounting and Placement of System Components Decide where to install your TeamWork system and where to place the individual components. z The Cable Cubby should provide easy access for as many users as possible. Ensure that there is ample space for cables under the table. Ensure that the edge on which the lid opens is correctly oriented. z The system controller should be placed close to the display. z The SW4 HDMI (or SW6 HDMI) switcher should be placed close to the Cable Cubby. z The analog-to-digital converter (with the optional TeamWork VGA kit) should be placed next to the switcher. Ensure that the VGA connector can connect to the converter and that the three-conductor pigtail can connect to the switcher. 080p Native Resolution Display VGA Show Me Cable HDMI Show Me Cable Switcher HDMI Video to Display SW4 HDMI Cable Cubby Cable Access Enclosure VGA Kit (optional) Power Supplies (2) Shown mounted with optional UTS 00/UTS 50 Under Table Shelf System. AC Power To Display System Controller Secure Show Me Cable to Cable Cubby and create a loop. Installing the Cable Cubby in the Table Before cutting the table and installing the Cable Cubby, see the Cable Cubby Setup Guide (see www.extron.com). ATTENTION: Ensure that the orientation of the cable cubby and the hole dimensions are correct before cutting the table. Assurez vous que la position du Cable Cubby et les dimensions du trou soient correctes avant de couper la table. After installation, secure the cables to avoid them becoming tangled (see the figure above). Après l installation, sécurisez les câbles de façon à éviter qu ils ne s emmêlent (voir l illustration au-dessus). 5
SHARE 30 TX 0 90 60 RX COM +5V LISTED 7TT APARATUS US TeamWork Kits Installation Guide (Continued) Cabling 2V 0.3A MAX SW4 HDMI Switcher TALLYOUT +V CONTACT G SW4 HDMI S 6 2 Contact Closure & Tally 5 00-20V 50/60Hz IPL T PC System Controller RS-232 Control Cable 2A MAX 2A MAX HDMI Pro Cable HDMI Video 3 6 IR IN S G AUDIO/VIDEO LAN Flat Panel AC Cord 4 60 30 0 Regional Sales 50 SOUTH 20 WEST EAST NORTH 90 Flat Panel Display w/ Integrated Speakers Regional Sales 50 SOUTH 20 WEST EAST NORTH Cable Cubby 2000 Cable Access Enclosure Show Me Cables Connect the Show Me cables to the source devices. 2 Connect the Show Me cables to the switcher. 3 Connect the switcher to the display. 4 Connect the display power cable to the system controller. 5 Connect the system controller to the switcher. 6 Connect power to the switcher and system controller. This diagram shows the TeamWork 400 system. To add a TeamWork VGA kit to the TeamWork system, see VGA Show Me Cables on page 8. 6
Show Me Cables The Show Me cables are for use with TeamWork systems. They feature a Share button for remote input source selection and a control pigtail, which may be wired directly into switchers with contact closure and tally outputs. HDMI Show Me cable (to source device) (to switcher) Top of Cable Cubby Share Button Three-conductor pigtail for contact closure and tally Bottom of Cable Cubby VGA Show Me cable (to source device) Top of Cable Cubby SHARE Share Button Three-conductor pigtail for contact closure and tally (to converter) Bottom of Cable Cubby HDMI Show Me Cables. Connect the input end of the Show Me cable to the source device. 2. Connect the HDMI output to the switcher. SW4 HDMI Switcher (HDMI input) SW4 HDMI S TALLY OUT 2V 0.4A MAX +v CONTACT G SHOW ME CABLE SWITCHER END (output) Male HDMI connector Three-conductor pigtail for contact closure and tally TALLY OUT +v CONTACT Red Black G Drain wire (not used) 3. Connect the black (Tally Out) and red (Contact) pigtail wires as shown above. The number under the Tally Out and Contact pins must correspond to the video input on the switcher. NOTES: The drain wire does not need to be wired to the switcher. The Show Me cables are grounded via the video connectors. Do not connect the Show Me cable to the +V pin on the switcher. Pigtail Press the Share button to switch the connected source to the main presentation display. Pressing the Share button creates a momentary contact closure, which triggers the switcher to select the connected source device. If a tally output is available, the button will light up blue. NOTES: The source device provides the +5 VDC supply voltage needed to illuminate the Share button. If the source device does not supply this +5VDC, the Share button will not illuminate. Some mobile devices do not provide the required voltage to light up the button. Digital Show Me cables support embedded audio and CEC signals. 7
VGA Show Me Cables. Connect the input end of the VGA Show Me cable to the source device. 2. Connect the output of the Show Me cable to the VGA input of the analog-to-digital converter. 3. Connect the HDMI cable from the digital output of the converter to the HDMI input of the switcher. HDMI Switcher Analog-to-Digital Converter 2V.0A MAX 4 RGB/R-Y,Y,B-Y AUDIO RGB - HDMI 300 A HDMI RS-232 SW4 HDMI 2V 0.3A MAX S SHOW ME CABLE Male VGA Connector SWITCHER END (output) 2 5 Three-conductor 3 pigtail for contact closure and tally. TALLYOUT +V CONTACT G TALLY OUT +v CONTACT SHARE Red Black G Drain wire (not used) Pigtail SHOW ME CABLE SOURCE END 4. (Optional) Connect the audio output from the source device to the 3.5 mm TRS audio input on the converter (the cable is not provided with the TeamWork VGA kit). The audio signal is embedded in the HDMI output signal. 5. Connect the black (Tally Out) and red (Contact) pigtail wires as shown above. The number under the Tally Out and Contact pins must correspond to the video input on the switcher. NOTES: The drain wire does not need to be wired to the switcher. The Show Me cables are grounded via the video connectors. Do not connect the Show Me cable to the +V pin on the switcher. Press the Share button to switch the connected source to the main presentation display. Pressing the Share button creates a momentary contact closure, which triggers the switcher to select the connected source device. If a tally output is available, the button will light up blue. NOTE: The source device provides the +5 VDC supply voltage needed to illuminate the Share button. If the source device does not supply this +5 VDC, the Share button will not illuminate. Some mobile devices do not provide the required voltage to light up the button. 8
Connect the Switcher to the Display Device Connect the switcher HDMI output to the HDMI input of the display device, using the provided cable. If necessary, see the user guide for the display device. Connect the Display to the System Controller Connect the power cord from the display device to the power output receptacle of the system controller. TeamWork systems work by controlling the AC power to the display. Connect the System Controller to the Switcher Connect the COM port of the system controller to the RS-232 port on the switcher with the provided control cable. System Controller (IPL T PC) COM Switcher (SW4 HDMI or SW6 HDMI) TX RX +5V 4-pole connector (to system controller) 5-pole connector (to switcher) Switcher Control Cable ATTENTION: The two ends of the RS-232 control cable are different. One has a 4 pole connector, the other has a 5 pole connector. Les deux terminaisons du câble de contrôle RS-232 sont différentes. L une a un connecteur 4 pôles, l autre a un connecteur 3 pôles. Connect Power The system controller uses an internal power supply. Connect the power cord to a wall outlet. The TeamWork 600 systems use a 6 input switcher with an internal power supply. Connect the power cord to a wall outlet. The TeamWork 400 systems use a 4 input switcher with a 2 VDC, A power supply, which is provided with the switcher. 2V 0.4A MAX ATTENTION: Do not connect the power supply to the SW4 HDMI switcher until you have read the Attention notifications in the Wiring the Power Supply section of the SW HDMI Series User Guide. Ne branchez pas le sélecteur SW4 HDMI avant d avoir lu la mise en garde dans la section «sources d alimentation» du SW HDMI Series User Guide. The optional TeamWork VGA kit also includes a 2 VDC, A power supply for the analog to digital converter. 9
Converter SIS Commands The following features have been pre-configured on the RGB-HDMI 300 A. The values should be re entered if they have been erased by a factory reset (see the RGB-DVI 300 and RGB-HDMI 300 (A) User Guide at www.extron.com for a complete explanation of SIS commands). Feature SIS Command Set output signal resolution to 080p E24*8RATE} Enable power save mode EPSAV} Enable Auto-Image *A Disable auto memories E0AMEM} Enable front panel security lockout X E = Escape key } = Carriage return (no line feed) Testing the System The TeamWork system has been pre-configured so that, once all the connections have been made and the devices are all powered on, there should be no need of further configuration for the system to work. To ensure that the system has been set up correctly, follow these steps:. Power on the equipment z Source devices z Switcher z System controller (IPL T PC) 2. Press the Power button () on the front panel of the system controller. The LED (2) lights green when power is being supplied to the attached output device. 3. Turn on the display and confirm that the display is receiving power. 4. Go to the menu for the display and disable the Sleep Mode feature. If necessary, see the user guide for the display. 5. Press the power button on the power controller. The LED should go out and the display should be turned off. 6. Connect one of the Show Me cables to a video source, such as a laptop. 7. Press the Show Me button on that cable. If the source device is providing a video signal, the LED on the Show Me cable lights blue and the display automatically turns on. 8. Connect a second Show Me cable to a second video source. 9. Repeat step 7 to verify that the second source device is providing a video signal and it is the output signal from the switcher. When the button on the second Show Me cable is pressed, the LED lights blue and the LED on the first cable is switched off. 0. Disconnect all the Show Me cables from the source devices. After about 30 seconds without an input signal, the display should turn off.. Connect a Show Me cable to a source device and press the Show Me button on that cable. As soon as an active video signal is detected, the display should automatically turn on. Troubleshooting IPL T PC No Image on the Display: Cause There is a problem with the source device: Solution Verify that the source device is powered on and outputs an active signal. Cause 2 Cable connections are incorrect: Solution Verify that the HDMI output cable from the switcher is connected to the current HDMI input of the display. R 2 TX RX IR 00 LINK ACT 0
Cause 3 Display is off: Solution Verify that the display is in the on state. Solution 2 The TeamWork system turns the display on and off by controlling the AC power. If the display has a Sleep Mode feature, this feature must be disabled to prevent the display from accidentally powering off. Cause 4 The display has a problem: Solution Verify that the display functions correctly. Cause 5 The display cannot show video at the incoming resolution: Solution The EDID settings on the switcher may need to be changed. Refer to the SW HDMI Series User Guide (see www.extron.com) or contact an Support representative at www.extron.com/company/contactus.aspx. Show Me Button LEDs Stay Off When Pressed: Cause The cable is not plugged into a source device that is producing an active video output signal: Solution Verify that the source device is on and producing an active signal. Cause 2 Contact or Tally wiring is incorrect: Solution See Show Me Cables (page 7) to ensure the contact and tally pins are correctly wired. Cause 3 The switcher is not powered on: Solution Verify that the switcher is powered on. Cause 4 Problem with Show Me cable: Solution Try connecting the video source with a different cable. If the second cable works correctly, there may be a problem with the Show Me cable. Contact Support at www.extron.com/company/contactus.aspx. Cause 5 Problem with Switcher: Solution If none of the cables work correctly, there may be a problem with the switcher. Contact an Support representative at www.extron.com/company/contactus.aspx. Cause 6 The source device does not output +5V: Solution This is a problem with the source device. HDMI specifications require pin 8 to carry a +5V output and VGA specifications require pin 9 to carry a +5V output. The Display Does Not Automatically Turn On: Cause Incorrect wiring: Solution Verify that the RS-232 communication cable is connected properly between the IPLink controller and switcher. Cause 2 There is no video signal present at Show Me cables: Solution Verify that an active signal is present at the input of any of the Show Me cables. Cause 3 IPLink configuration on the system controller is missing or corrupted: Solution Contact an Support representative at www.extron.com/company/contactus.aspx. Cause 4 Display power is out of sync: Solution The display is in standby mode. Turn on the display using the remote or the physical power button. Cause 5 Display has sleep mode enabled Solution Go to the menu for the display and disable the sleep mode feature. Turn on the display using the remote or physical power button. The Display Stays On and Never Turns Off: Cause Video signal is present at Show Me cables: Solution Verify that no active signals are present at the inputs of any of the Show Me cables. The TeamWork system is designed to turn off the Display only when no video signals are present.
Headquarters +.800.633.9876 (Inside USA/Canada Only) USA - West USA - East +.74.49.500 +.99.850.000 +.74.49.57 FAX +.99.850.00 FAX Europe +800.3987.6673 (Inside Europe Only) +3.33.453.4040 +3.33.453.4050 FAX Asia +65.6383.4400 +65.6383.4664 FAX Japan +8.3.35.7655 +8.3.35.7656 FAX China +86.2.3760.568 +86.2.3760.566 FAX Middle East +97.4.299.800 +97.4.299.880 FAX Korea +82.2.3444.57 +82.2.3444.575 FAX India 800.3070.3777 (Inside India Only) +9.80.3055.3777 +9.80.3055.3737 FAX 2 205 Electronics All rights reserved. www.extron.com 68-2400-5 Rev A 0 5