LED REFLECTOR WALL WASHER Our LED Wall Washers adopt high Power LED in RGB or single color as light source. It could be used in indoor or outdoor. The LED Wall Washer is our patented product with uniform mixed lights, distinctive appearance and so on. Its effect of mixed light used our company Self-developed Integral and ubiquitous reflector. To break with traditional way whose effect of mixed light is used LED Lens. The body of this product adopts distinctive style design with smooth lines, fine appearance and so on. The whole lamps and lanterns look very good. It is used matching bracket to achieve installing beside the wall or vertical the ground. It needn t adjust the angle to get very good lighting effect. It is used hand in hand connection among lights with conveniently installing and operating simply.
Single color LED Wall Washer is lighting once power-on. RGB LED Wall Washers are of 13 kinds of effects inside, connecting consoles outside, and so on for your choice. It could be integral controlling or stepshaped changing controlling. The mixed changing color is composed by red, green and blue with many kinds of lighting presenting continuous to beautify the environment and dot the city. Application: LED wall washer can be widely used for indoor, outdoor decoration and stage, meeting room, exhibition lighting, ancient buildings and cultural plaza and other places. Technique Parameters: Item WW8003 WW8004 WW8001 WW8002 Input Voltage Working Voltage AC90V~AC260V(50/60Hz) DC24V Max Power 37Watts 78Watts 19Watts 36Watts LED current Light Source 350 MA RGB High Power LED Single color as clients requirement 12leds/0.5m 24leds/1m 12leds/0.5m 24leds/1m Luminous Flux 380lm 760lm 620 lm 1165 lm LED Projecting Way Self-developed Integral and ubiquitous reflector Signal Standard DMX512 \ Control Way Environment Temperature IP rank Outside using DMX Control Box or DMX512 Standard Console; \ Master-Slave Services (Lighting once power-on) -20~ 40 IP65
Connection Ports: Power input port with 3-pin male waterproof connector Power output port with 3-pin female waterproof connector Standard DMX signals input port with 3-pin male waterproof connector Standard DMX signals output port with 3-pin female waterproof connector Button Functions: Each RGB wall washer has 14 color modes for options. Please refer to the MODE DETAILS Press these 2 buttons for different choices. Button 1 is for increasing, and button 2 is for decreasing. Please see the below: Interface display functions Instructions: 1. 001~512: means the wall washer is on the mode of being controlled, in this mode, the wall washer will be controlled by the main wall washer. 2. H-1~H-D: main control mode, in this mode, all the following connected wall washer, can change the same lighting effect as the first one. Modes Details 001~512: DMX code H-1: Single Red H-2: Single Green H-3: Single Blue H-4: Single Yellow H-5: Single Cyan H-6: Single Purple H-7: Single White H-8: 7-color Jumping changing H-9: 3-color Jumping changing H-A: 7-color Gradual changing H-b: 3-color Gradual changing
H-C: 7-color Flash changing H-D: 3-color Flash changing Dimension Drawing: 500mm Third-Single row led wall washer 1000mm Third-Single row led wall washer Attention 1. When you use the product, please make sure it works in good condition. 2. Each single row wall washer takes up 3 addresses, the first wall washer s address plus 3 is the address for the next one. 3. If you want all connected wall washers to change color together, you should set the same address for
all the wall washers. 4. Please set the address from 001 to 512. 5. The maximum address should be less than 510. 6. There should be only one main wall washer as a key controller (the wall washer works in main control mode, dmx512 control box or dmx console). 7. When many single row wall washers connected together, the connection please refers to the connection diagram. 8. The connection cable between two DMX Signals amplifier, or between DMX console and DMX signal amplifier, It can t exceed 100m; The distance between the first DMX signals amplifier or DMX console and the last wall washer can t exceed 100m. Connection Layout: Method 1
Method 2
Indoor and Outdoor use Warning 1. When the product in the packing box, please do not connect the power source; 2. Before installing please do not connect the high-voltage power supply, and make sure the equipment connect ground; 3. Replace any protection cover which is busted; 4. Attention fire protection, against electricity and quakeproof.
Before installing the product please read the instruction carefully, also please preserve this document for future reference. Attention Corrosiveness or soluble chemicals will make the outer covering protection of lamps to be destructed. Normal working temperature: - 35 ~40, the humidity: 0~95%, if surpasses this prescribed limit, it will have the disadvantageous influence to the life time. Storing temperature: -35~70. We are not being responsible for the aftereffect which use any correlative accessory is not provided by our company. Accessories for products connection Picture Product name Description 1. Part No.: CT-1001 2.Voltage: AC100-240V DMX512 3. One DMX512 controller box at least connect 30pcs led wall washers within controller box 100M.If more than 30pcs, should connected a signal amplifier. Each signal amplifier can connect 30pcs led wall washers...and so on. 4. size: 130*90*49MM, weight: 0.75KG.
DMX512 signal amplifier 1. Part No.: CT-2001 2. Voltage: AC100-240V 3. Can be repeater when in a longer signal transmission, then signal regeneration and branches, it can connect 30pcs led wall washes and a signal amplifier within 100M.Mainly use parallel and series connections cables. 4. Size: 130*90*49MM, weight: 0.75KG. 485 1-1 signal amplifier 1. Part No.: CT-2002 2. Voltage: DC12V 3. Can be repeater when in a longer signal transmission, then signal regeneration and branches, it can connect 30pcs led wall washes and a signal amplifier within 100M.Mainly use parallel and series connections cables. 4. size: 73*38*25MM, weight: 0.2KG. Accessories Needed: Description Quantity Unit Picture Comment Instruction Book 1 Copy Normal Tail Plug for transformer 1 Piece Normal Tail Plug for transformer 1 Piece Normal 3-pin waterproof female connector 1 Piece Normal Transfer Line (3pin XLR male connector switch to 3pin female connetor, 0.5m long. 1 Piece Optional