Wide View LCD 6 x Pushbuttons & Display DISTINCTIV CHARACTRISTICS Programmable display graphics for alphanumeric characters and animated sequences 6 colors of backlighting can be controlled dynamically Pushbutton switches or display with LCD, RGB LD backlighting General brightness of backlight is dynamically controlled in eight steps from dark to bright Operated by commands and data supplied via serial communications (SPI) Incorporates bitmap display function Dual image VRAM for quick change of displayed images Travel options: Standard travel of.mm, or long travel of.5mm (same as KP0 Series) Low energy consumption Dust tight construction Viewing areas: Switches - 7.0mm x.0mm (horizontal x vertical) Display -.mm x.mm High reliability and long life of one million (short travel) or three million (long travel) actuations High resolution of 6 x pixels poxy sealed straight PC terminals Snap-in standoff legs on the switches, or display s bracket with crimped legs, ensure secure mounting and alignment and prevent dislodging during wave soldering. Standard Travel Actual Sizes of Switches & Display Long Travel Display //
Wide View LCD 6 x Pushbuttons SWITCH PART NUMBRS & DSCRIPTION Part Numbers Switch Description LCD Mode LD Color IS5BFPRGB-0YN IS5BFPRGB SWITCH SPCIFICATIONS IS5BFPRGB-0YN RGB LD Backlight Black and White LCD Standard Travel SPST Momentary ON Gold Contacts Straight PC Terminals Standard Travel Black & White FSTN Positive Circuit SPST normally open SPST normally open lectrical Capacity (Resistive Load) 00mA @ V DC 00mA @ V DC Red/Green/Blue Long Travel Contact Resistance 00 milliohms maximum @ 0mV 0mA 00 milliohms maximum @ 0mV 0mA Insulation Resistance 00 megohms minimum @ 00V DC 00 megohms minimum @ 00V DC Dielectric Strength 5V AC for minute minimum 5V AC for minute minimum Mechanical ndurance,000,000 operations minimum,000,000 operations minimum lectrical ndurance,000,000 operations minimum,000,000 operations minimum Operating Force.7 ± 0.5 Newtons.0 ± 0.5 Newtons Total Travel.mm (.07 ).5mm (.77 ) TYPICAL SWITCH DIMNSIONS FOR STANDARD TRAVL See Pixel Detail (0.5). (.).5 Pixel Detail.66 (6.56).65 (.5).7 (.). (0.5).06 (0.).00 (0.0) Typ.000 (.66).5 (.0).5 Standoff Detail (0.5). (0.).00 Standoff = (.7).06 (.0).06 A Dimension A (0.0). (.5).0 Dia IS5BFPRGB RGB LD Backlight Black and White LCD Long Travel (0.6) Typ.0 (0.) Typ.06 See Standoff Detail (.).6 Standoff = (.).0 Footprint Terminal numbers are not on the switch. (.0).7 Standoff.60 Standoff (7.6).00 (5.0).5 Standoff Standoff (0.) Typ (0.) Typ.0.00.6 7x (0.75).00 7 5 (6.5).50 (6.5). 6.60 6 7 5 (6.5). (6.5).50 The Compact LCD 6 x Pushbutton may utilize the same footprint as the Standard Travel LCD 6 x Pushbutton. (.5).0 (.5).0 x (0.).05 (7.6).00 (5.0).5 x (.) Dia.05 Landless.6.70
Wide View LCD 6 x Pushbuttons TYPICAL SWITCH DIMNSIONS FOR LONG TRAVL LCD SPCIFICATIONS Characteristics of Display Display Operation Mode Display Condition Viewing Angle Direction Viewing Area Pixel Format Pixel Size Absolute Maximum Ratings (Temperature at 5 C) FSTN positive; background colors, black & white Transflective with built-in LD backlight 6 o clock 7.0mm x.0mm (horizontal x vertical) 6 x pixels (horizontal x vertical) 0.mm x 0.5mm (horizontal x vertical) *Operating Temperature Range 5 C ~ +50 C (+5 F ~ + F) Storage Temperature Range Backlight LD See Pixel Detail (0.5). (.).5 Pixel Detail 0 C ~ +60 C ( F ~ +0 F) RGB: red/green/blue * In a low temperature environment (below 0 C), speed and contrast decrease when image changes. The non-indicator dot may become dense in a high temperature environment (about +50 C). Highest backlight brightness level should not be used for temperatures above +5 C. Items Symbols Ratings Supply Voltage V DD 0.V to +7.0V Input Voltage V I 0.V to V DD +0.V Output Voltage V O 0.V to V DD +0.V Optical Characteristics (Temperature at 5 C) Items Symbols Min Typical Max Contrast Ratio Cr.0 Viewing Angle (Cr.) (0.5).06.66 (6.56).65 (.5).7 (.). (0.).00 (0.0) Typ.000 (.66).5 (.0).5 Standoff Detail (0.).00 Standoff = (.7).06 (.0).06 A Dimension A (.5).0 Dia (.).5 (0.6) Typ.0 (0.) Typ.06 See Standoff Detail Standoff = (.).0 Footprint Terminal numbers are not on the switch..70 Standoff Standoff (7.6).00.60 Up & Down q 0 Right & Left f 0.6 Standoff Standoff (0.) Typ.0 The following pages for Wide View LCD 6 x Pushbuttons apply to the both Standard Travel and Long Travel LCD 6 x Pushbuttons. (.)..6 7x (0.75).00.5.7.70.7.5 6 7 5 x (0.).05 (7.6).00.60 x (.) Dia.05
Wide View LCD 6 x Pushbuttons Recommended Operating Conditions (Temperature at 5 C) Items Symbols Minimum Typical Maximum Supply Voltage V DD.V 5.0V 5.V High Level Input Voltage V IH 0. V DD Low Level Input Voltage V IL 0.V DD SPI Clock Frequency f MHz Current Consumption I DD ** 0mA *** 60mA ** 0mA: Backlighting LD is off *** 60mA: Backlighting LDs (Red, Green, Blue) are maximum brightness SWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS Pin No. Symbol Name Function 5 6 7 NC SDO VDD GND SW Terminal of Switch Normally open SW Terminal of Switch Normally open GND 7 6 5 SW bit Shift Register SPI Common Driver Display Controller RAM # 56Byte Ground RAM # 56Byte seg...seg6 6bit Shift Register 6 x Dot Matrix LCD Panel V DD Power Power source for logic circuit and LCD SDO Data Out Data output line for SPI Data In Data input line for SPI Serial Clock Clock line for SPI that synchronizes commands and data Slave Select Chip select for SPI; line is active low NC None No connection Com...Com Segment Driver LD Driver Backlight LD Red Green Blue SW 5
Wide View LCD 6 x Pushbuttons, Display & Compact TIMING SPCIFICATIONS FOR SWITCHS & DISPLAY SPI Characteristics (See Timing Diagram) (Temperature at 5 C ~ +50 C and V DD = 5.0V ± %) Items Symbols Minimum Maximum SPI_ Set Up Time ts 0ns SPI_ Hold Time th 0ns SPI_CLK Cycle tcycck MHz SPI_CLK Width thwck 0ns SPI_DI Set Up Time tsdi 0ns SPI_DI Hold Time thdi 0ns SPI_DO Delay Time tddo 0ns SDO BITMAP ts tsdi SPI Timing Chart ( Using) tcycck thwck thdi D7 D6 D5 D D D D Segment D0 tddo D7 D6 D5 D D D D D0 th SDO CLK_ CLK_ CLK_ Low IS_ IS_ IS_7 Circuit xample IS_ IS_5 IS_ DATA_ DATA_ DATA_ SPI Timing Chart ( Low Level Fixed) tsdi tcycck thwck thdi D7 D6 D5 D D D D D0 tddo and shall be kept high when idle. IS_ IS_6 IS_ It is recommended that all pins be connected to a controller pin instead of ground. A clock glitch during power up could cause the communication to fall out of sync. Toggling the line resets the communication. D7 D6 D5 D D D D D0 Common 5 6 7 6 56 57 5 5 60 6 6 6 6 Byte Byte7 Byte Byte COM D0 D D D D D5 D6 D7 D0 D7 D0 D7 D0 D D D D D5 D6 D7 Byte6 COM D0 D D D D D5 D6 D7 D0 D D D D D5 D6 D7 Byte Byte56 Byte COM D0 D D D D D5 D6 D7 D0 D D D D D5 D6 D7 Transferring Display Data/Displaying LCD and Data Sequence Data (56 Bytes) 0 x 55 Byte Byte Byte55 Byte56 0 0 0 0 D7 D6 D5 D D D D D0 D7 D6 D D0 D7 D6 D5 D D D D D0 Notes: Display RAM has two screen areas. The first area is for the display on current LCD; the second area is for the data to be displayed next. The screens are changed when the second area is fully stored.
Wide View LCD 6 x Pushbuttons, Display & Compact COMMANDS & DATA Transferring display data/displaying on LCD: command ( Byte) + data (56 Bytes) Others: command ( Byte) + data ( Byte) s can be accepted only when all bits coincide; otherwise, they are not acknowledged Additional commands will not be received until the communication of commands ( Byte) and data (56 or Byte) is completed There is no time limit from the beginning to end of data receipt s may be executed consecutively (no need to wait between commands) Irregular commands or data are not recognized Initial status at power activation: LCD display off, LD off (brightness /0, color off) Transferring Display Data/Displaying on LCD Hex Binary Data Remarks 0 x 55 0000 56 Bytes (6 x =,0 bits) See above for details of bitmap data LD (Backlight) Color Set Hex Binary 0 x 0 0000000 LD (Backlight) Brightness Set Hex Binary Data R R G G B B bits x Data 0 x 000000 * * * bits Reset (Returning to Initial Status at Power Activation) Hex Binary Data 00 = off 0 = / 000 = /0 (dark) 00 = /0 00 = /7 0 = /5 Remarks For each of RGB: Remarks For leading bits: Remarks 0 = / = full 00 = / 0 = / 0 = / = full (bright) 0 x 5 000 000000 Returning to initial status at power activation
Wide View LCD 6 x Pushbuttons, Display & Compact PRCAUTIONS FOR HANDLING & STORAG OF LCD 6 x DVICS Handling. The IS Series devices are electrostatic sensitive.. Limit operating force to keytop to 00.0N maximum, as excessive pressure may damage the LCD device.. The IS series devices are not process sealed.. If the LCD is accidentally broken, avoid contact with the liquid and wash off any liquid spills to the skin or clothing. 5. Clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent. 6. Recommended soldering time and temperature limits: Do not exceed 60 C at the LCD level. Wave Soldering: see Profile B in Supplement section. Manual Soldering for Switch: see Profile A in Supplement section. Manual Soldering for Display: see Profile B in Supplement section. 7. xcessive images may result after the same image is emitted continuously for an extended period of time.. The highest backlight brightness level should not be used for temperatures above +5 C. Storage. Store in original container and away from direct sunlight.. Keep away from static electricity. ATTNTION LCTROSTATIC SNSITIV DVICS. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination.
OPTIONAL ACCORIS AT70-05K Socket for LCD 6 x Pushbutton Materials: Base - Glass Fiber Reinforced PBT Terminals - Brass/Beryllium Copper The socket permits the to be plugged in after automated processing. Use of the socket enables easy field replacement of the device. (0.).7 AT70-05L Socket for OLD Pushbutton Materials: Base - Glass Fiber Reinforced PBT Terminals - Brass/Beryllium Copper The socket permits the OLD to be plugged in after automated processing. Use of the socket enables easy field replacement of the device. (0.).7 AT70-05M Socket for OLD Display Materials: (.).0 Base - Glass Fiber Reinforced PBT Terminals - Brass/Beryllium Copper (.6). (7.). (0.5) Dia Typ.00 The socket permits the OLD SmartDisplay to be plugged in after automated processing. Use of the socket enables easy field replacement of the device. (7.6).6 (.).0 (.).7 (.).65.76 (.).7 (7.). (0.5) Dia Typ.00 (0.5).00 DiaTyp (7.6).00 (7.6).00 (0.0)..5.5 (6.).66.7.7 (5.5).07 (7.5).5.6 Optional Accessories Compatible Part Number for AT70-05K.76 Wide View/Long Travel LCD 6 x.76 IS5BFPRGB.6.76.76 7.7 0.7 (5.5).07 (6.).66.5.5 (7.6).00 x (0.75) Dia.00 Compatible Part Numbers for AT70-05L OLD Pushbutton ISC5ANP (7.6).00 0x (0.75) Dia.00 Compatible Part Number for AT70-05M OLD Display ISC0P Frameless OLD ISF5ACP (0.0). x (0.75) Dia.00 50