FACT Cable Termination Unit INSTALLATION INSTRUCTION FACT-GSS NOTE: - the FACT-GSS multi-purpose splice shelves features Single Circuit and Single Element fiber management system technology - these shelves supports splicing for multiple application like: - outdoor to indoor loose tube cable - loose tube cable to pigtail - loose tube cable to breakout or intrafacility cable - pigtail to pigtail - one FACT-element is designed to enter from each side with max. 8 FOPT-tubes or 48x single-pigtails 1,8mm or 48x 900µm IFC cable - for cable installation and fiber routing into the shelf please refer to appropriate cable-kit installation instructions - a dedicate area allows to install up to 2 Splitter OCC1-Series - a x:2 FBT-Splitter can be installed a special FACT-organizer tray CONTENT 1 General 1.1 Kit content 1.2 Tools required 2 Mounting FACT-GSS module 3 Dismounting FACT-GSS module 4 Internal tray to tray fiber routing 5 OCC1-splitter installation and routing 6 x:2 FBT-splitter installation on splice tray and routing
1 General 1.1 Kit content FACT-GSS-4E-48x4 1x Splice-Shelf for SC-application (max. 96 fiber) 4-Elements, 48x SC (Smouv or ANT) splice cassettes FACT-GSS-4E-32x12 ANT 1x Splice-Shelf for SE-application (max. 384 fiber) 4-Elements, 32x SE (ANT) splice cassettes FACT-GSS-1E-12x4 1x Splice-Shelf for SC-application (max. 24 fiber) 1-Elements, 12x SC (Smouv or ANT) splice cassettes FACT-GSS-1E-8x12 ANT 1x Splice-Shelf for SE-application (max. 96 fiber) 1-Elements, 8x SE (ANT) splice cassettes 2
FACT-GSS-4E-24x12 SMOUV 1x Splice-Shelf for SE-application (max. 288 fiber) 4-Elements, 24x SE (Smouv) splice cassettes FACT-GSS-1E-6x12 SMOUV 1x Splice-Shelf for SE-application (max. 72 fiber) 1-Elements, 6x SE (Smouv) splice cassettes 1.2 Tool required No tools needed to install the shelf Standard installation tooling for fiber optic cable 2 Mounting FACT-GSS module 2.1 Prepare the rack with the brackets on the position where you want to install the FACT-GSS module 2.2 Slowly slide the module to the back (push simultaneously on both sides, with both hands) until you clearly hear a CLICK noise 3
3 Dismounting FACT-GSS module 3.1 Open upper drawer (releasable) 3.2 Pull the orange puller locks (make sure both sides are in the unlocked position) 3.3 Slowly slide the module out (pull simultaneously on both sides, with both hands) 4 Internal tray to tray fiber routing 4.1 Internal splice-connection, leaving and entering at the same side 4
4.2 Internal splice-connection, leaving and entering not at the same side 5 OCC1-splitter installation and routing 5.1 Push the release-button and open the labeling-sheet-holder 5.2 Tilt all trays in on step like shown in the picture 5.3 Install splitter by pushing to the right untill you hear a click noise 5
5.4 Route the splitter-input/output-fibers throughout the groove plate to preferred splice-cassettes and splice with dedicated fiber. Coil the fibers into the fiber-storage 6 x:2 FBT-splitter installation and routing 6.1 Push the release-button and open the labeling-sheet-holder 6.2 Install splitter by simple click-in the splitter-cassette like shown in the picture 6.3 Splice the splitter-input-fiber on dedicated fiber and coil the fibers into the fiber-storage 6.4 Splice both splitter-output-fibers on dedicated fibers and coil the fibers into the fiber-storage 6
7
CommScope Connectivity Belgium bvba Diestsesteenweg 692 B-3010 Kessel-Lo, Belgium Tel.: 32-16-351 011 Fax: 32-16-351 697 commscope.com Visit our website or contact your local CommScope representative for more information. 2016 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks or trademarks, respectively, of CommScope, Inc. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to CommScope products or services. TC 1338/7/IP/1 08/16