LCD HDTV/DVD COMBO USER S MANUAL SLC-2269A-3

LCD HDTV/DVD COMBO USER S MANUAL SLC-2269A-3 USER S MANUAL

Important Safety Precautions Important Safety Precautions 1 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol indicates important instructions accompanying the product. This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. When servicing use only identical replacement parts. Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. This symbol indicates "dangerous voltage" inside the product that presents a risk of electric shock or personal injury. WARNING To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The apparatus must not be exposed to dripping or splashing. Objects filled with liquids, such as vases or drinking glasses, must never be placed on the apparatus. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984 (Section 54 of Canadian Electrical Code, Part 1) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antennadischarge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrode. See following example. ELECTRIC SERVICE EQUIPMENT NEC-NATIONAL ELECTRICALCODE ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNINT (NEC SECTION 810-21) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250 PART H) 16. Mains plug is used as the disconnect device. It shall remain readily operable and should not be obstructed during intended use. 2

Table of Contents Introduction Features Specifications 5 6 Table of Contents Time Setup Lock 28 26 26 DVD Part-BASIC OPERATION 30 Accessories General Description Overview of front and side panel Overview of back panel Overview of remote control Installing Batteries in the Remote Control 7 7 8 9 10 13 Troubleshooting 32 External Connection Antenna connection Connecting VCR 13 13 14 Connecting DVD Player/Set-Top Box 15 Connecting DVD Player/Set-Top Box via HDMI Connnecting Digital Audio System Connecting Amplifier/DVD Home Theater Connecting PC 16 17 17 18 Supporting signals Basic operation Turning the TV On and Off Input Setup Channels Selection Volume Adjustment and Mute Setup Current Channel in formation 21 EPG Menu 18 19 19 20 20 20 21 Menu system introduction Picture Sound Channel 22 22 23 24 3 4

Introduction Introduction WFeatures arnings WSpecifications arnings ltv adopts TFT LCD display screen lhdtv Compatible( 480p,720p, 1080i, 1080p) lsupport American TV Standard 8VSB/Free 64/256QAM,NTSC System, ATSC System lconnect to computer directly to realize TV/monitor combo. lzero X radiation complies to green environment protection requirement ladvanced Chroma Processing lclosed captioning/parental LOCK lsap/stereo/mono; BTSC. lhdmi input lsupport COAXIAL ouput MODEL mm SLC-2269A-3 22 1680X1050 55W 533X196X397 4.9Kg Color active matrix LCD display Fine digital control Input terminals used for external equipment connection One computer VGA/PC input One COAXIAL output One COMPONENT input One HDMI input One AV input One AUDIO output One ANTENNA jack Adapter requirement IN Put Out Put NTSC System, ATSC System Antenna: 2~69; Cable: 1~135 (Analog: 1-125, Digital: 1-135) NTSC3.58 DC: 12V 5A 75 (Unbalance) (Max) 5WX2 DC 3V (Two AAA size batteries) o o 0C-40C Note: Design and specification modification maybe made at any time without prior notice; all data and dimensions are approximations. 5 6

RECALL CH.LIST EJECT OSD MENU EXIT SF -/-- POWER MTS V+ V+ ENTER SOUND CC CH+ CH- B.MARK RANDOM REPA-B PICTURE DISPLAY FAV.LIST PAUSE/PLAY STOP EPG STEUP ZOOM DVD MENU REPEAT S.TITLE GO TO ANGLE CLEAR PBC AUDIO PROGRAM D.ZOOM Accessories Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer. General Description Overview of front and side panel HDMTV Remote Control & Owner s Instructions Batteries (AAAx 2) MENU INPUT CH- CH+ VOL- VOL+ General Description Overview of side the DVD panel 8 5 4 6 7 Press button on the side panel or on the remote controller After placed a disc in the disc tray, press button to play the disc,and press button twice to pause Press button to stop in two modes: press the button once,stop memorize the interrupt position and the OSD shows pre-stop resume play by pr-essing button, press button twice to complet-ely stop disc,the osd shoe stop and then press the button to resume playing from the beginni-ng of the disc SPEAKER REMOTE CONTROL SENSOR Aim the remote control towards this spot on the TV. POWER INDICATOR Green: In power on mode. Red: In standby mode. INPUT Toggles between all the available input sources ( TV,AV, DVD,COMPONENT, HDMI, VGA) MENU Press to see an on-screen menu of your TV's features. CH+/- Press to change channels. In the on-screen menu, use the CH +/- buttons as up/down arrow buttons. VOL+/- Press to increase or decrease the volume. In the on-screen menu, use the VOL +/- buttons as left/right arrow buttons. Standby button Press button to toggle between normal and standby mode. 7 8

General Description General Description Overview of back panel Overview of remote control HDMI Connect to the HDMI jack of a device with an HDMI output. VGA/PC IN Connect to the video output jack on your PC. PHONE OUT Connect a set of phone for private listening COMPONENT Connect Component video. COMPOSITE VIDEO Video input for external devices, such as a camcorder or VCR. COMPOSITE COMPONENT AUDIO Audio inputs for external devices. 10 AUDIO OUT Connect to the audio output jacks on your amplifier/home theater. COAXIAL Connect to a Digital Audio devices. ANT Connect to an antenna or cable TV system. DC12V IN PHONE Connect the supplied power 10 1 2 3 6 7 10 11 13 22 4 5 9 8 12 16 14 15 17 19 RECALL CH.LIST EJECT OSD MENU EXIT SF. -/-- POWER MTS V+ V+ ENTER SOUND CC CH+ CH- B.MARK RANDOM REPA-B PICTURE DISPLAY PAUSE/PLAY STOP STEUP DVD MENU REPEAT S.TITLE GO TO ANGLE CLEAR PBC AUDIO PROGRAM D.ZOOM HDTV FAV.LIST EPG ZOOM 18 21 20 23 TV MODE: 1.POWER Button( ) Press this button to turn the TV on or into standby mode. 2.MUTE Button Press this button to mute the sound and the sign of mute will appear all the while if you do not press again. But the sign of mute will disappear if the CCD is displayed. 3.SLEEP Button Press this button to set the sleep timer. When the preset length of time has passed, the TV set enters standby 5 10 30 45 60 90 120 180 240 minutes. 4.SOUND Button Press this button to select desired sound mode. Four sound modes are available including Standard, Music, Movie and Personal. 5.PICTURE Button Press this button to select desired picture mode. Four picture modes are available including Standard, Soft, Dynamic and Personal. 6.RECALL Button This button is used to return to the previous channel 7.MTS Button W hen stereo program is received, press this button to switch sound system between mono and stereo. When SAP program is received, press this button to switch sound system between mono and SAP. When stereo and SAP program is received, press this button to switch among mono, stereo and SAP. 8.CC Button This button doesn t Look in this model 9. DISPLAY Button Press this button to display the information on current input. 10.NUMBER (0-9)Buttons Press these buttons to enter digits. These buttons for direct access to use a channel to enter channel number for both ATV and DTV or enter password for Parental lock. 11."-/--,." Button In TV mode, press this button and input the channel number which you want to select. Press this button to display the input source such as 12.AV/TV/DVD Button "TV, "AV, " DVD, "Component","HDMI" and "VGA" Using UP/DOWN button select item and press RIGHT or ENTER button to enter selected item. 13. CH. LIST Button Press this button to display the channel list in TV mode. 14.VOLUME+/VOLUME- (V+/V-) Buttons Press these buttons to increase or decrease the volume. 9 10

( ( / / ) )

SLEEP P.MODE S.MODE LIST DTV 1 2 3 SOURCE +-./ ABC DEF PHONE General Description Installing Batteries in the Remote Control External Connection Connecting VCR 1 Installing Batteries Open the battery compartment cover on the back side. These instructions assume that you have already connected your TV to an antenna or a cable TV system. Skip step 1 if you have not yet connected to an antenna or a cable system. Battery TV Rear Panel Cover Point the remote towards the remote control sensor of the wireless TV and use it within 7 meters. VCR Rear Panel 2 Insert two 1.5V AAA size batteries in correct polarity. Don t mix old or used batteries with new ones. Put the used batteries into the recycling bin since it can negatively affect the environment. 2xsize AAA 1.5V 3 Closed the cover. 5 4 Audio Cable (Not supplied) Video Cable (Not supplied) Battery Cover 3 RF Cable (Not supplied) The batteries shall not be eposed to ecessive heat such as sunshine fire of the like. Universal Remote Control operation please refer to Appendix 2. External Connection Antenna connection Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be connected to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder cable, you need to use the 300ohm/75ohm converter to connect the antenna cable to the antenna jack. For details Please refer to the following drawing. Antennas with 300 W flat twins Leads Antennas with 75 W Round Leads Follow the instructions in Viewing a VCR or Camcorder Tape to view your VCR tape. Each VCR has a different back panel configuration. When connecting a VCR, match the color of the connection terminal to the cable. We recommend the use of cables with a Ferrite Core. 1. Unplug the cable or antenna from the back of the TV. 2. Connect the cable or antenna to the ANT IN terminal on the back of the VCR. 3. Connect an RF Cable between the ANT OUT terminal on the VCR and the ANT IN terminal on the TV. 4. Connect a Video Cable between the VIDEO OUT jack on the VCR and the VIDEO IN jack on the TV. 5. Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AUDIO L and AUDIO R jacks on the TV. If you have a mono (non-stereo) VCR, use a Y-connector (not supplied) to hook up to the right and left audio input jacks of the TV. If your VCR is stereo, you must connect two cables. Use a 75ohm - 300ohm converter ANT IN 300ohm coaxial cable Antenna feeder 75ohm coaxial cable Antenna cable 13 14

PHONE PHONE External Connection Connecting DVD Player/Set-Top Box The rear panel jacks on your TV make it easy to connect a DVD to your TV. TV Rear Panel DVD Player/Set-Top Box External Connection Connecting DVD Player/Set-Top Box via HDMI This connection can only be made if there is a HDMI Output connector on the external device. DVD Player/Set-Top Box TV Rear Panel 2 Audio Cable (Not supplied) 1 Component Cable (Not supplied) Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting the video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also. Each DVD player/stb has a different back panel configuration. When connecting a DVD player/stb, match the color of the connection terminal to the cable. We recommend the use of cables with a Ferrite Core. 1. Connect a Component Cable between the COMPONENT IN [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR] jacks on the DVD player. 2. Connect Audio Cables between the COMPONENT IN [RAUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD player. HDMI Cable (Not supplied) What is HDMI? HDMI, or high-definition multimedia interface, is a next-generation interface that enables the transmission of digital audio and video signals using a single cable without compression. Multimedia interface is a more accurate name for it especially because it allows multiple channels of digital audio (5.1 channels). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP(High Bandwidth Digital Copy Protection) coding feature installed, and supports multi-channel digital audio. Each DVD player/stb has a different back panel configuration. We recommend the use of cables with a Ferrite Core. 1. Connect an HDMI Cable between the HDMI connector on the TV and the HDMI connector on the DVD player/set-top Box. 15 16

PHONE PHONE PHONE External Connection Connecting Digital Audio System The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV. Digital Audio System TV Rear Panel External Connection Connecting PC PC TV Rear Panel COAXIAL Cable (Not supplied) 1 D-Sub Cable (Not supplied) 2 Phone Out 5.1 CH audio is possible when the TV is connected to an external device supporting 5.1 CH. We recommend the use of cables with a Ferrite Core. 1. Connect an COAXIAL Cable between the SPDIF jacks on the TV and the Digital Audio Input jacks on the Digital Audio System. When a Digital Audio System is connected to the SPDIF terminal: Decrease the gain (volume) of the TV, and adjust the volume level with the system's volume control. Each PC has a different back panel configuration. The HDMI jacks do not support PC connection. We recommend the use of cables with a Ferrite Core. 1. Connect a D-Sub Cable between RGB/PC IN connector on the TV and the PC output connector on your computer. 2.Plug PHONE out connector into PHONE out jack on the TV the TV speaker will be muted. Connecting Amplifier/DVD Home Theater Amplifier/DVD Home Theater TV Rear Panel Supporting signals Input Mode Air Cable 8VSB Free 64/256QAM CVBS NTSC 3.58 Audio Cable (Not supplied) Each external input source device has a different back panel configuration. When connecting an external device, match the color of the connection terminal to the cable. We recommend the use of cables with a Ferrite Core. 1. Connect Audio Cables between the AUDIO L and R OUT on the TV and AUDIO IN [R- AUDIO-L]on the Amplifier/DVD Home Theater. When an audio amplifier is connected to the AV OUT [R-AUDIO-L] terminals: Decrease the gain (volume) of the TV, and adjust the volume level with the Amplifier's volume control. VGA/PC Component HDMI 640x480/60Hz 800x600/60Hz 1024x768/60Hz 480p/60Hz 720p/60Hz 1080i/60Hz 480p/60Hz 720p/60Hz 1080i/60Hz 1680x1050/60Hz 1080p/60Hz 1080p/60Hz 17 18

1 Basic Operation Turning the TV On and Off How to turn the TV on or off 1. Insert the power cord plug into a polarized AC outlet. 2. Press POWER button on the remote control or button on the LCD TV. 3. Normal picture will be displayed on the screen after 6 seconds. If no signal input, "No Signal" will be displayed on the screen. 4. If temporary POWER off is required, press POWER button on the remote control or button on the LCD TV. 5. If you want to completely switch off the power for this unit, unplug the power cord plug for this unit. 6. After switching off the unit, you should turn on the TV again at least 5 seconds later. Status indication lamp Green: In power on mode. Red: In standby mode. Auto power -off If there is no signal input in any Mode, the TV will automatically accesses the standby state in about 15 minutes. Memory before turning TV off The settings of picture and the preset channels will be memorized at turning off the unit. When being started up again, the unit will work according to the mode set before being turned off. To use Car cord Use the Car Cord provided for operation on 12V. DC NOTE: 1.AC/ DC adaptor provided can be connected to the specified voltage (AC 110 volts 60HZ). 2.If the polarized AC cord does not fit into a non polarized AC outlet, do not attempt to file or cut the blade. It is the user s responsibilityto have an electrician replace the obsolete outlet. 3.If you cause a static discharge when touchingthe unit, and the unit fails to function, simply unplug the unit from the AC outlet, wait a few minutes, and plug it back in. The unit should return to normal operation. NC 2 3 Basic Operation Menu operation 1Input Setup Press AV/TV/DVD key on the remote control to enter "INPUT SOURCE" menu. There are five options for you to select: "TV", "AV", "DVD","Component","HDMI",and "VGA. Use /qkey to move the cursor to the input you desired and press ENTER key to confirm. Channels Selection There are four ways to select channel: 1) Using 0~9, keys on the remote control to select channel directly. 2). Using CHr/skey on the remote control or on your TV to select channel. 3) Press PRE.CH key to turn to previous channel, press it again to return to current channel. Note: PRE.CH is not activated if no channel has been changed after TV turning on. 4) Select channels from "All Channels List" or "Favorite Channels List". Volume Adjustment and Mute Setup Volume adjustment Press VOL +/- key on the remote control or on the TV to display "Volume" menu, adjust the volume of TV between 0 to 100 by using VOL +/- key: ( To increase the volume, press VOL + key; ( To decrease the volume, press VOL - key; Mute Press MUTE key on the remote control to display mute icon on the left bottom of the screen, and the volume of TV will be turned off, press MUTE key again to turn on the volume. Mute can be canceled by using one of the methods below: ( Mute will be canceled if you press MUTE button again. ( Mute will be canceled if you press VOL + key. TV AV DVD Component HDMI VGA 19 20

4 5 Basic Operation Menu operation Current Channel Information Press INFO key on the remote control to display the following OSD, the indications of items in this OSD are listed in the following table. EPG Menu Press EPG key to enter "EPG" menu, the first line displays current channel number channel name, event title and current time. The second line displays all programs which will be displayed in this channel, press t/ukey to select the program you desired, then press ENTER key to enter this program to watch. Menu system instruction Picture Picture Press MENU key to display the main menu on the screen, use t/ukey to select "Picture" option, then press ENTER or qkey to enter "Picture" submenu. 1. Picture mode In "Picture" submenu, use / key to move the cursor to "Picture Mode" option to set the mode of video picture. Use t/u key to select one picture mode from four modes: "Standard", "Dynamic, "Soft" and "Personal". 2. Contrast In "Picture" submenu, use / key to move the cursor to "Contrast" option, then press t/ukey to adjust the value. 3. Brightness In "Picture" submenu, use / key to move the cursor to "Brightness" option, then press t/ukey to adjust the value. 4. Color In "Picture" submenu, use / key to move the cursor to "Color" option, then press t/ukey to adjust the value. 5. Tint In "Picture" submenu, use / key to move the cursor to "Tint" option, then press t/ukey to adjust the value. 6. Sharpness In "Picture" submenu, use / key to move the cursor to "Sharpness" option, then press t/ukey to adjust the value. 7. Color Mode In "Picture" submenu, use / key to move the cursor to "Color Mode" option, then press t/ukey to select one color mode from:"normal", "Warm", "Cool". 21 22

Menu system instruction Sound Sound Menu system instruction Channel Channel Press MENU key to display the main menu on the screen, use t/ukey to select "Sound" option, then press ENTER or key to enter "Sound" submenu. 1. Sound Mode In "Sound" submenu, use / key to move the cursor to the "Sound Mode" option, then use t/ukey to select one mode from following four modes: "Standard", "Music", "Movie and "Personal". 2. Bass In "Sound" submenu, use / key to move the cursor to the "Bass" option, then use t/ukey to adjust the value. 3. Treble In "Sound" submenu, use / key to move the cursor to the "Treble" option, then use t/ukey to adjust the value. 4. Balance In "Sound" submenu, use / key to move the cursor to the "Balance" option, then use t/ukey to adjust the value. 5. Surround In "Sound" submenu, use / key to move the cursor to the "Surround" option, then use t/ukey to select "On" or "Off". 6. AVC In "Sound" submenu, use / key to move the cursor to the "AVC" option, then use t/ukey to select "On" or "Off". 7. SPDIF Type Only when the input source is DTV, the function of SPDIF Output is available. In "Sound" submenu, use / key to select "SPDIF" option. There are two modes for you to select:"raw" and "PCM". Use t/ukey to select the mode you desired. 8. Audio Language In "Sound" submenu, use / key to move the cursor to the "Audio Language" option, there are three options for you to select: "French", "Spanish" and "English". Press t/u key to select the language you desired. Press MENU key to display the main menu on the screen, uset/ukey to select "Channel" option, then press ENTER or key to enter "Channel" submenu. 1. Antenna In "Channel" submenu, use / key to move the cursor to "Antenna" option. There are two options for you to select:"cable" and "Air", press t/ukey to select the Antenna type you desired. 2. Auto Scan In "Channel" submenu, use / key to select "Auto Scan", then press ENTER or u key to enter "Auto Scan" submenu. 1) Use / key to select "Cable System", If you have selected "Cable" in "Antenna", there are four options for you to select: "AUTO", "STD", "HRC" and "IRC". Press t/ukey to select the option you desired. 2) Then use / key to select "Auto to Scan", press ENTER key or ukey to start searching. If you want to stop searching, just press EXIT key. 3. Auto Scan add CH In "Channel" submenu, use / key to select Auto Scan add CH, then press ENTER or u key to enter Auto Scan add CH submenu. 4. Favorite In "Channel" submenu, use / key to select "Favorite", then press ENTER key to enter "Favorite" submenu. Use / key to select your favorite channels and use ENTER key to mark " and the selected channel will be listed in Favorite List. 23 24

Menu system instruction Channel 5. Show/Hide In "Channel" submenu, use / key to select "Show/Hide", then press ENTER key to enter "Show/Hide" submenu. Press / key to select the channel you want to hide or show, then use ENTER key to mark or remove " " and the selected channel will be hiden or shown. 6. Channel No. In "Channel" submenu, use / key to select "Channel No.", then press t/ukey to adjust current channel, you can see the current channel number. 7. Channel Label In "Channel" submenu, use / key to select "Channel Label", then press ENTER "Channel Label" submenu. Use to enter t/ukey to select and use / key to input the character or digit you want, press MENU key to confirm, then current channel is labeled. Notes: 1. If the channel is audio program, an icon will be displayed in front of "Radio channel". 2. If a program has been added to "Hide" list, when you select program with CH / CH key, this program will be directly jumped, but you can select the program by using digital key on the remote control. Menu system instruction Time Time Press MENU key to display the main menu on the screen, use t/ukey to select "Time" option, then press ENTER or key to enter "Time" submenu. 1. Sleep Timer In "Time" submenu, use / key to move the cursor to "Sleep Timer" option. There are eleven options for you to select: "Off", "5 Min", "10 Min", "15 Min", "30 Min", "45 Min", "60 Min", "90 Min", "120 Min", "180 Min" and "240 Min", press t/ukey to select "Sleep Time" you desired. 2. Time Zone In "Time" submenu, use /qkey to move the cursor to "Time Zone" option. There are six options for you to select: "Eastern", "Central", "Mountain", "Alaska", "Pacific", "Hawaii". Press t/ukey to select "Time Zone" your desired. 3. Daylight Saving time In "Time" submenu, use /qkey to move the cursor to "Daylight Saving Time" option. You can press t/ukey to select "On" or "Off". 4. Clock Show the update time. Setup Setup Press MENU key to display the main menu on the screen, use t/ukey to select "Setup" option, then press ENTER or key to enter "Setup" submenu. 1. Menu Language In "Setup" submenu, use /qkey to move the cursor to select "Menu Language" option, there are "English", "Français" and Español" options you can select. Press t/ukey to select the option you desired. 2. Transparency In "Setup" submenu, use /qkey to move the cursor to select "Transparency" option, there are "On" or "Off" options you can select. Press t/ukey to select the option you desired. 25 26

Menu system instruction Setup 3. Zoom Mode In "Setup" submenu, use /qkey to move the cursor to select "Zoom Mode" option, there are four options for you to select: "Wide", "Zoom", "Cinema" and "Normal". Press t/ukey to select zoom mode you desired. Note: In the VGA mode, you can only choose Normal and Wide. In the mode of Component and HDMI, you can only choose the Wide, Cinema and Zoom. 4. Noise Reduction In "Setup" submenu, use /qkey to move the cursor to "Noise Reduction" option, there are four options for you to select: "Off", "Weak", "Middle" and "Strong". Press t/ukey to select noise reduction you desired. 5. Advance In "setup submenu, use / key to move the cursor to the "Advance" option, then use t/ukey to adjust the related value. This function is only available for VGA. 1) H-POS In "Advance submenu, use /qkey to move the cursor to the "H-POS option, then press t/ukey to adjust the value. 2) V-POS In "Advance submenu, use /qkey to move the cursor to the V-POS option, then presst/ukey to adjust the value. 3) CLOCK In "Advance submenu, use /qkey to move the cursor to the CLOCK option, then presst/ukey to adjust the value. 4) PHASE In "Advance submenu, use /qkey to move the cursor to the PHASE option, then presst/ukey to adjust the value. 5) AUTO In "Advance submenu, use /qkey to move the cursor to the AUTO option, then press ukey this option will auto adjust the H-POS,V-POS,CLOCK and PHASE of the VGA picture. 6. DLC(Dynamic Luminance Control) In "Setup" submenu, use /qkey to move the cursor to select "DLC" option, then press tor ukey to select "On" or "Off". 7. Restore Default In "Setup" submenu, use /qkey to move the cursor to select "Restore Default" option, then press ENTER or ukey to enter "Restore Default" submenu. Use t/ukey to select "Yes" or "No", then press ENTER to confirm. If you select "Yes", all settings will be restored default settings. Menu system instruction Lock Lock Press MENU key to display the main menu on the screen, use t/u key to select Lock option, then press ENTER or u key to enter Enter Password, input the password to enter Lock submenu (the default and universal password is 0000). 1. Change Password In Lock submenu, use / key to move the cursor to select "Change Password" option, then press 0-9 digital keys to enter "Change Password" submenu. Use digital keys on the remote to change the password. Only when you input the same password twice,the password is set successfully. 2. System Lock In "Lock" submenu, use / key to move the cursor to select System Lock option, then use t/ukey to select "On" or "Off". Note: Only when the System Lock is "On", you can use / key to move the cursor to "US", "Canada" and "Reset RRT". 3. US In Lock submenu, use / key to move the cursor to select "US" option, then press ENTER u key to enter "US" submenu. or 27 28

Menu system instruction Lock 1) TV In "US" submenu, use / key to move the cursor to select "TV" option, then press ENTER or u key to enter "TV" submenu. Use / andt/u key to select the option you desired. Press 2) MPAA ENTER key to lock the option. In "US" submenu, use / key to move the cursor to select "MPAA" option. There are seven options for you to select : "R", "NC-17", "X", "N/A", "G", "PG press t/u key to select the option you desired. 4. Canada "and"pg-13", In "Lock" submenu, use / key to move the cursor to select "Canada " option, then press ENTER or u key to enter "Canada " submenu. 1) Canada English In "Canada" submenu, use / key to move the cursor to select"canada English" option. There are seven options for you to select: "C", "C8+", "G", "PG", "14+", "18+" and "E". Press t/u key to select the option you desired. 2) Canada French In "Canada" submenu, use / key to move the cursor to select "Canada French" option. There are six options for you to select: "E", "G", "8ans+", "13ans+", "16ans+" and "18ans+". Press 5. Reset RRT t/u key to select the option you desired. In "Lock" submenu, use / key to move the cursor to select "Reset RRT " option, then press ENTER or u key to enter "Reset RRT "submenu. Use t/u key to select "Yes" or "No", then press ENTER to confirm. If you select "Yes", all RRT settings will be restored default settings. DVD OPERATION Basic Operation 1. Turn On the TV and then press"av/tv/dvd" button of the remote controller, the TV will switch into DVD mode. 2. Place a disc horizontally into the disc slot,it will then be automatically loadedinto the mechanism. NOTE:Another disc can not be loaded if there isalready one in mechanism. b. No disc in mechanism, it will be initialized when the power turns on (automatically loads in about7 seconds). c. When it ejects, the disc will be automatically reload after about 10 seconds later if not removed. d. Compatible with both 12CM disc. a) Menu Play(compatible with DVD VCD2.0 discs) I. Stop 1) When you press thestop button for the first time, the player to pre-stop mode. 2) In pre-stopmode, the player remembers where you have stopped,when you start playing the discagain, the DVD player will pick up where you stopped. b) Title Play (compatible with DVD discs only). I. During DVD playback, press the Title button to display the DVDtitle contents. c) programme Play (compatible with DVD,VCD,CD, JPEG discs) The programme Playback option allows you to enter the order in which you want chapters or tracks to be played, a maximum of16. INITAL SETTING(DVD) Setup Menu 29 30

DVD remote control Troubleshooting 1. TV 2. 3. 4. CLOSED 5. MUTE 1. 2. TV TYPE:According to the COLOR Type of the TV,you can choose the TV Type according to your TV. NOTE:AUTO type is recommended. 8 3. 4. DEFAULT : Back to the factorysetting. 31 32

33 Picture defects and the reason

MSD119