INSTR.RB24-9014_JULY 2015 v1.1 AUTOMATE PARADIGM CUT-IN WALL SWITCH Single, Double and Fifteen Channel Switches. FRONT LCD Screen UP STOP DOWN P2 Button UP STOP DOWN P2 Button + CHANNEL - CHANNEL 15 Channel 2 Channel 1 Channel BACK PACK CONTENTS Switch Fixing screws & anchors Instruction Manual 1.5V AAA Battery (QTY 2) Battery Compartment (Shown with cover in position) TECHNICAL SPECIFICATIONS Voltage: Frequency: 3V (2X AAA) 433.92 MHz TransmittingPower: 10 milliwatt Ambient Operating Temperature: Transmission Distance: -10 C - 50 C up to 200 meters (open space) 433MHz Page. 1 of 6
CONTENTS Installing switch batteries Mounting cut-in switch Select channel to be programmed Pairing switch to motor Group Control Adding & deleting switches. Adding & deleting channels. Troubleshooting p3 p3 p4 p4 p4 p5 p5 p6 U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Declaration of Conformity required for EU market CAUTION Do not expose to moisture or extreme temperatures Replace with correct battery type as specified Do not allow children to play with this device or battery. Use or modification outside the scope of this instruction manual will void warranty. DISPOSAL Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately Page. 2 of 6
INSTALL REMOTE BATTERY 1 2 3 Replace cover Remove cover from remote: with 2 fingers placed in upper area of cover, press gently in and down to disengage cover and slide down to remove Install battery with negative(-) sides facing the springs by reversing step 1 INSTALL WALL MOUNT HOLDER Use supplied fasteners and anchors as needed to attach base to desired surface as shown in figure Page. 3 of 6
1. SELECT CHANNEL TO BE PROGRAMMED (For Single Channel Remote skip to Pairing Remote to Motor ) Detail View of Remote Controls 15 Channel Switch Only Press Channel + button until desired channel is reached on LCD screen 2. PAIRING REMOTE TO MOTOR ACTIVATE PAIRING MODE ON MOTOR 2a (Any Motor) Press & hold button on motor head (3sec) OR 2a (Non-Battery Motor) Power ON motor BEEP 1X 2b Within 4sec, Press & Hold STOP (3sec) JOG 2X + BEEP 3X 3. GROUP CONTROL Explanation: in this step you are going to pair multiple motors to a single channel on your remote. This will allow you to operate a series of motors in unison without needing to change channels. Ensure that each motor you want to group is also assigned to another channel by itself Confirm that motor limits and favorite position are already set for each individual motor Select the channel you want to control the group of motors with REPEAT steps 2A and 2B for all motors using your desired group channel NOTE: Channel zero defaults to group control for all motors paired to remote Page. 4 of 6
4. ADDING & DELETING SWITCHES A = Existing Switch B = New Switch 4a 4b 4c (Switch B) SWITCH TO REMOTE B 5. ADDING & DELETING CHANNELS A = Existing Channel B = New Channel 5a 5b 5c (Switch B) SWITCH TO REMOTE B Page. 5 of 6
TROUBLESHOOTING PROBLEM CAUSE REMEDY Motor is not responding Cannot set limits on a single Motor (multiple motors respond) Switch battery is discharged Battery is inserted incorrectly Radio interference / Shielding Receiver distance is too far from remote Power failure Incorrectwiring Using group channels to adjust motor limits Replace battery Check battery polarity Ensure remote is positioned away from metal objects and that aerial on motor or receiver is kept straight and away from metal. Move remote to a closer position. Check power supply to motor is connected and active. Check wiring is connected correctly (refer to motor installation instructions) Always reserve an individual channel for programming functions. SYSTEM BEST PRACTICE Provide an extra 15 channel remote in your multi motor projects, that provides individual control for each motor for programming purposes. ROLLEASE ACMEDA USA 200 HarvardAvenue Stamford, CT 069026320 T +1 203 964 1573 F +1 203 964 0513 ROLLEASE ACMEDA AUSTRALIA 110 Northcorp Boulevard, Broadmeadows VIC 3047 T +61 3 9355 0100 F +61 3 9355 0110 ROLLEASE ACMEDA EUROPE Via Conca Del Naviglio 18, Milan (Lombardia)Italy T +39 02 8982 7317 F +39 02 8982 7317 Western Australia Branch Unit 1, 41 MulgulRoad, Malaga WA6090 T +61 8 9248 5571 F +61 8 9248 5572 Queensland Branch Unit 2/62 Borthwick Avenue, Murarrie QLD 4172 info@rolleaseacmeda.co m rolleaseacmeda.com Page. 6 of 6