A CENTURY OF AUTOMOTIVE VISION SAFETY WIRELESS KIT FOR ROSCO BACKUP CAMERA SYSTEMS STSW1001T STSW1001R STSW1001 INSTALLATION / USER'S MANUAL
Wireless Kit For Backup Camera Systems TABLE OF CONTENTS Introduction........................................................ 2 Technical Description................................................. 3 Transmitter Details................................................... 4 Receiver Details...................................................... 5 Wiring Diagram...................................................... 6 Installation........................................................... 7 Pairing............................................................. 8 Troubleshooting...................................................... 9 STSW1001 WIRELESS KIT FOR ROSCO BACKUP CAMERA SYSTEMS The STSW1001 Wireless Kit can be used with most Rosco backup camera systems. The Wireless Kit eliminates the need for a hard-wired connection between the camera and monitor. The transmitter connects to the camera and will wirelessly transmit video and audio to the receiver, which then displays the image on the monitor. 2
STSW1001 TECHNICAL DESCRIPTION The radio link consists of a transmitter module and a receiver module. They transmit videos and sound wirelessly from the camera to the monitor. The transmitter module is preferably powered via IGN source and is also used to supply the camera with power. See pg. 8 for pairing options and instructions. The receiver module is powered by the monitor. The wireless signal is transmitted in the 2.4 GHZ range. The system is intended as an aid for reversing, Driver must use mirrors and proper care when reversing.................................. i NOTICE! The system transmits digital data, which is then converted to an analog signal for display on the monitor. If the monitor displays a yellow warning triangle, there is a fault in the video transmission. It is possible that the display of the camera image on the monitor is delayed. There is a slight delay (typically 0.2 seconds) depending on environment and other factors. 3
Wireless Kit For Backup Camera Systems TRANSMITTER DETAILS fig 1 NO. IN FIG.1, MEANING 1 Antenna connection 2 Pairing button 3 Operating mode display: LED glows red when signals are being transmitted LED flashes red when the components are being paired 4 Camera Connection 5 Blue cable (CAMERA POWER TRIGGER): voltage supply for camera 6 Green cable (REVERSE TRIGGER): control cable for activating the pairing signal 7 Red cable (DC INPUT): Connection to the positive terminal of the voltage supply; preferably IGN 8 Black cable (GND): Connection to the negative terminal of the voltage supply or ground 4
STSW1001 RECEIVER DETAILS fig 2 NO. IN FIG.2, MEANING 1 Antenna connection 2 Pairing button 3 Operating mode display: LED glows red when signals are being transmitted LED flashes red when the components are being paired 4 Monitor connection 5 Green cable (REVERSE TRIGGER): control cable for activating the pairing signal 6 Black cable (GND): Connection to ground 5
Wireless Kit For Backup Camera Systems WIRING DIAGRAM Black(GND) Red(Power 12V-32V in) STSW1001T Transmitter TX White(C2 Trigger) Green(C1 Reverse) FUSE/2A M12 M10 C2 F C1 Connected to Camera 122CM Black: GND Black: GND Green:Reverse (for pairing) FUSE/2A Green:Reverse(for Reverse pairing) Blue:Camera Camera Power Power Red:DC12V-24V Red: DC12V-24V Black: Black: GND GND C1 M10 M12 C2 TX White(C2 Trigger) Green(C1 Reverse) FUSE/2A STSW1001R Receiver M12 M10 PAIRING Pairing: LED LED Red(Power 12V-32V in) Black(GND) RX RX RING D M12 M10 Connected to Monitor Green Green:Reverse (for pairing) (for pairing) Black: GND Black: GND 6
STSW1001 INSTALLATION i NOTE! Video and sound are sent from the transmitter module to the receiver module. To ensure proper functioning, it is important to check whether the wireless transmission is stable before final installation. To test the installation, proceed as follows: Attach the modules temporarily to the planned installation location. Install the rear view video system if you have not already done so. Start up the rear view video system. If the camera image transmission is stable (two or three reception bars at the top right of the monitor), you can complete final installation of the two modules. If faults occur (only one reception bar or a yellow warning triangle on the top right of the monitor) turn or move the transmitter or receiver module slightly and conduct further tests. Attaching the modules To do this, proceed as follows for each module: Hold the module at the chosen location and mark the four points for drill holes. Drill holes with a diameter of 5/32in (#21) at each of the points you just marked. Screw the module on with #10-32 self-tapping screws.......................................................... i Fixing the antennas NOTE! Always align the antennas in the same direction, for example, both vertically. This improves the transmission performance. You can glue the antennae on the corresponding module. 7
Wireless Kit For Backup Camera Systems PAIRING - 2 OPTIONS i NOTE! The transmitter module and the receiver module have to be paired with each other so that the monitor can display the camera images. This is conducted at the factory. OPTION 1: Pairing the system manually with the pairing button Press the pairing button on the receiver module three times within 10 s (press the button approx. 1 time per second). The LED on the receiver module flashes red. The monitor displays the message Pairing Start and a counter that counts down 50 s. You need to perform the pairing of the transmitter module within 50 s. Press the pairing button on the transmitter module three times within 10 s (press the button approx. 1 time per second). The LED on the transmitter module flashes red. The modules synchronize themselves with each other. This takes approx. three to five seconds. For successful pairing, the monitor shows the Save data message and the picture appears. If pairing is unsuccessful, the monitor displays the message Pairing Failed. Repeat the pairing procedure......................................................... OPTION 2: Pairing the system with reverse gear You can start pairing the module via the reverse gear if you connect the red cable from the transmitter module to the positive terminal and the green cable of both modules on the reversing light Switch on the monitor. Activate the required channel. Engage and disengage the reverse gear three times within 10 s. The LED on the transmitter module and the LED on the receiver module flash red. The modules synchronise themselves with each other. This takes approx. three to five seconds. For successful pairing, the monitor shows the Save data message and the picture appears. If pairing is unsuccessful, the monitor displays the message Pairing Failed. Repeat the pairing procedure. 8
STSW1001 TROUBLESHOOTING FAULT CAUSE SUGGESTED REMEDY The monitor displays the message No Signal The transmitter module is not working. Check the voltage supply. The monitor displays the message Reverse for Imaging The green and the blue cable are incorrectly connected. The transmitter module is not receiving a video signal. Check the camera connection and function. The monitor displays the message Pairing Failed. The start signal (on/off three times) is incomplete or missing. Repeat the system pairing until the monitor displays Save data. The monitor displays the message wait for TX. Regular image playback or yellow warning triangle on the screen. Transmitter and receiver modules have lost identification. The transmitter module has no voltage supply. - Check the voltage supply. Make sure that the antennae of the receiver module and the transmitter module are firmly connected. Check the reception bars on the monitor. If only one reception bar is displayed, change the position of the transmitter or receiver module. Check if the battery charge is sufficient. 9
Wireless Kit For Backup Camera Systems NOTES 10
STSW1001 NOTES 11
A CENTURY OF AUTOMOTIVE VISION SAFETY 90-21 144th Place, Jamaica, New York 11435 TEL (800) 227-2095 FAX (718) 297-0323 info@roscomirrors.com www.roscomirrors.com www.roscovision.com